6700 Series Art " hands free colour display digital videophone ENG D E 200mm 27mm PT3 PT2 G PT1 A 150mm H F SW2 PT4 NO C VA GND 12M GND BUS2 BU

Size: px

Start display at page:

Download "6700 Series Art " hands free colour display digital videophone ENG D E 200mm 27mm PT3 PT2 G PT1 A 150mm H F SW2 PT4 NO C VA GND 12M GND BUS2 BU"

희본 석
4 years ago
Views:

1 Art " hands free colour display digital videophone ENG D E 200mm 27mm PT3 PT2 G PT A 50mm H F SW2 PT4 NO C VA GND 2M GND BUS2 BUS AL LB GND A +DOL DOL B C I JP SW SW3 Fig. DESCRIPTI Surface mount hands free intelligent Videophone using 7 full colour active matrix LCD monitor for VX2300. Including 4 buttons service, privacy/bus relay activation, door- open/intercommunicating call and answer/camera recall plus 3 LED s for visual indication of privacy, door open services enabled and functions activated. Adjustments & programmable options: call tone volume on 3 levels (low, medium, high), speech volume, call tone melody, number of rings, and privacy duration. Also includes a local bell function. Fig. 2 LEGEND A Connection terminals B 8 Way dip switch bank C 4 Way dip switch bank D Contrast adjustment trimmer E Hue adjustment trimmer F Speech volume control sliding wheel G Brightness control sliding wheel H Call tone volume switch I Bus termination switch PUSH BUTTS (FIG. ) Service push button. When pressed it links internally the terminals C and NO on the connection terminals. Privacy -OFF push button. To enable the function press this button when the videophone is in stand-by. The service is automatically disabled when the programmed time expires (the privacy duration time can be programmed) or manually by pressing again the button. Activate bus relay board Art push button. To activate a bus relay, during a conversation, press this button quickly as many times as the address value of the relay. Camera switch push button. If the door station uses the Art. 4303N combined with Art. 4330N and Art. 4302V, pressing this button during a conversation switches the video signal coming from the internal camera module to the video signal coming from the camera module input for external camera. During the conversation, press and keep pressed the button until the camera switches. Repeat the operation to switch back to internal camera. Call Reject Button. During an incoming call, press this button to reject the call. The visitor doesn t receive any warning of the call rejected. Door open push button. Press this button to open the door when you are in conversation or you are receiving a call. Intercommunication push button. For an intercommunicating call, press as many times as the extension or address value to call (see SW3 Intercommunication Settings) EN - V. - 3/0/6

2 Art " hands free colour display digital videophone PUSH BUTTS (FIG. ) Answer push button. On an incoming call, operation of this button allows the user to answer and converse with the visitor. The relevant LED will illuminate. Switch off button. With the system switched on (monitor on), momentary operation of the button will switch the video monitor off. The videomonitor will also automatically switch off after a time delay if the button is not pressed. The relevant LED will switch off. Camera Recall push button. Press as many times as the DEVICE N. of the door station to switch on. Simplex button. Pressing and holding the button for more than 3 seconds will switch the videomonitor into SIMPLEX speech mode. Press and hold the button to speak to the caller ( LED will flash rapidly), release the button to listen ( LED will flash slowly). If the button is not pressed for 0 seconds the videomonitor will switch off. The videomonitor will revert to duplex speech when another call is made. LEDS (FIG. ) Privacy on LED LED It illuminates when the privacy service is enabled. Generic use LED It is controlled from the terminals +DOL and LED DOL. Normally used to signal the door status (open or closed). LED LED It illuminates when the videophone is switched. CTROLS (FIG. 2) Brightness control PT (sliding wheel). Call tone volume control SW2 (3 levels switch). Speech volume control PT4 (sliding wheel). Hue adjustment trimmer PT2 (rotate left to increase or right to decrease). Contrast adjustment trimmer* PT3 (rotate left to increase or right to decrease). *Not available in some LCD versions. Bus termination switch JP (upper position = BUS termination active, lower position = BUS termination disabled). PROGRAMMING The videophone setup consists of the following settings: Number of rings; Melody selection; Privacy duration; Unit address (..27, switches to 7 of SW); Bus Termination (open or close, jumper JP); Intercommunication mode (between apartments or within apartment, switch of SW3); Extension address (..4, switches 2,3 of SW3); Slave switch on mode (switch 4 of SW3). The programming of the number of rings, melody and privacy duration are carried out through the videophone push buttons, all other settings are carried out on the two dip-switch banks (SW and SW3) on the rear side of the video monitor (all the settings can be done without opening the videophone). It is necessary to remove temporary the power supply after making any programming changes. NUMBER OF RINGS, MELODY SELECTI AND PRIVACY DURATI All programming options are available only when the system is in stand-by. NUMBER OF RINGS. Keep pressed the button until the two LEDs and switch on. Press the button for the number of times corresponding to the required number of rings to set. A beep confirms each time the button is pressed. Once the required number of rings is reached, wait approx 5 seconds for the two LED s to switch off. The new value is stored. MELODY SELECTI Keep pressed the button until the two LEDs and switch on. The unit emits the current selected melody. Press the button and keep it pressed to listen the next melody. Repeat the operation until the required melody is found. Once the required melody is found, wait approx 5 seconds for the two LED s to switch off. The new melody is set EN - V. - 3/0/6

3 Art " hands free colour display digital videophone PRIVACY DURATI Keep pressed the button until the two LEDs and are switched on. Press the button for the number of times corresponding to the required privacy duration to set. Each time the button is pressed, the duration is increased by 5 minutes: i.e. to set 2 hours, press the button 8 times. Once the required privacy time is reached, wait approx 5 seconds for the two LED s to switch off. The new duration is set. VIDEOPHE ADDRESS SW...7 The table below shows how to set the address of the videophone. Considering that = and OFF = 0, multiply each digit for the relevant decimal weight then sum values obtained to get the address: E.g. as highlighted in the SW...7 table OFF,,OFF,OFF,, OFF, in binary is equal to 0000 then multiplying each digit for the relevant decimal weight you obtain the address that is 37. SWITCHES STATUS BINARY CODE - DECIMAL WEIGHT ADDRESS OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF Note: The maximum number of units allowed is 00 but the address of each unit can be a value between and 27. VIDEOPHE END OF LINE TERMINATI JP Looking at the videophone from the rear: Move the switch JP to the upper position to enable the bus termination. Move the switch JP to the lower position to disable the bus termination. In case of more units (intercoms, videophones or video monitors) in a parallel connection (bus wires are connected to the terminals of the first unit then from this to the second and so on up to 4 units max) the BUS termination must be enabled only for the last unit in the chain while on all other units it must be set to disabled. INTERCOMMUNICATI MODE SW3. This switch establishes the intercommunication mode: in OFF position (default) intercommunication is between units in the same apartment (same addresses but different extension); in position the intercommunication is between SW3. units in different apartments (different addresses). On installations where there are more than one intercom/videophone in the same apartment and intercommunication between different apartments is required, only one intercom/videophone may be set with this function (SW3.=, SW3.2=OFF, SW3.3=OFF). The other intercom/videophones in the apartment must be set for local intercommunication with extension addresses 2-4 (slaves). From the intercom/videophone set for intercommunication with other apartments it will not be possible to intercommunicate within the apartment but slave extensions 2-4 will be able to intercommunicate with each other within the apartment. EXTENSI NO SW If the intercommunication between apartments is enabled (switch of SW3 = ) leave these two switches in default position (both to OFF). Otherwise, if the intercommunication is between the same apartment (switch of SW3 = OFF), set the SW extension addresses starting always from. During the external call, all video monitors in the same flat will ring but the video will be shown only from the videophone with extension address. 2 3 EXTENSI NO. OFF OFF (default, master) OFF 2 (slave) OFF 3 (slave) 4 (slave) EN - V. - 3/0/6

4 Art " colour display videophone SLAVE SWITCH MODE - SW3.4 This set up concerns the answering mode of the video monitor when there is more than one unit (max 4) in the same apartment. OFF (default) = during a call, only the video monitor with extension (master) will show the video. = SW3.4 the video monitor will be switched on independently of the extension address: in this case the video monitor must be supplied locally using a power supply Art. 323/2 or Art. AMR2-2 and connecting respectively + to terminal 2M and to terminal GND on the connection terminals (the local power supply is required for each black & white slave videophone or starting from the third slave videophone when they are all colour videophones). If you set for one slave videophone, you must set the same switch also for the relevant master videophone. SIGNALS CNECTI TERMINALS Signal Description BUS Bus input BUS2 Bus input GND Ground 2M +2Vdc power supply input (Art. 323/2 or Art. AMR2-2) for version with Memory Board option or auxiliary power supply input (to be used when two or more slave monitors are ringing together with the switch 4 of SW3 is set to ) GND Ground VA Not used C Dry contact. Internally linked to NO when the button is pressed. NO Dry contact. Internally linked to C when the button is pressed. Max 35Vdc, 50mA DOL Auxiliary LED power supply input (ground) +DOL Auxiliary LED power supply input (+2Vdc) GND A Ground output for use in combination with AL & LB active low inputs LB Local bell input (active low) AL Alarm input (not implemented yet) TECHNICAL SPECIFICATI Housing/Mounting: Videophones / surface mount Push buttons: Yes, 4 Programming: Yes, carried out by the buttons and the dip-switches located on the rear of the videophone Controls: Call tone volume, picture hue, brightness and contrast Power Supply: Supplied by the BUS line Power consumption: Stand-by: 0.6mA Operating: 300mA Working Temperature: C MEMORY BOARD This device is also available in the version with memory board (Art. 6788/VM). If you have that version, please refer to the 6200, 6300, 6400 and Memory Board user manual for installation and use. The manual is available for download at the following link: EN - V. - 3/0/6

5 Art " Hands free colour display digitalvideophone To next Video Distributor To Videophone ART.6788 Extension N. Videophone: ART.6788 Extension N. Videophone: ART.6788VM Extension N. Videophone: BUS OUT BUS OUT 2 BUS OUT 3 BUS OUT 4 S S2 S3 S4 AMPLIFICATI H BUS LINE TERMINATI M OFF L BUS BUS IN OUT Art.37N Art.AMR2-2 2Vdc Art.: "AMR2-2" power supply. Use it for memory video model. MAX N 0 MITOR Art.232 BUS N.B. Chiudere la linea BUS sull'ultimo distributore. Close the bus line on the last video distributor Art.4302NV-4302NRV N.B. Dopo ogni cambiamento nella programmazione del posto esterno, del videocitofono o del relè, è necessario togliere l'alimentazione al sistema e ripristinarla affinchè le variazioni vengano recepite dai rispettivi dispositivi. After each change on the programming of the door station, videophone or any other device connected to the system it is necessary to restart the system (power off then power on). Title: Titolo: Videx Electronics S.p.A. Via del Lavoro, Monte Giberto (FM) Phone: Fax info@videx.it Notes: Note: 2Vac SE 2 Push to Exit Data creazione: 28/09/206 Data modifica: 28/09/206 Autore: Marco@videx.it Cod.File: 23KVD003E.dwg Foglio / EN - V. - 3/0/6

6 Art " Hands free colour display digitalvideophone To next Video Distributor To Videophone ART.6788 Extension N. Videophone: N.B. Dopo ogni cambiamento nella programmazione del posto esterno, del videocitofono o del relè, è necessario togliere l'alimentazione al sistema e ripristinarla affinchè le variazioni vengano recepite dai rispettivi dispositivi. After each change on the programming of the door station, videophone or any other device connected to the system it is necessary to restart the system (power off then power on). ART.6788 Extension N. Videophone: ART.6788VM Extension N. Videophone: BUS OUT BUS OUT 2 BUS OUT 3 BUS OUT 4 S S2 S3 S4 AMPLIFICATI H BUS LINE TERMINATI M OFF L BUS BUS IN OUT Art.37N Art.AMR2-2 2Vdc Art.: "AMR2-2" power supply. Use it for memory video model. MAX N 0 MITOR Art.232 BUS N.B. Chiudere la linea BUS sull'ultimo distributore. Close the bus line on the last video distributor Art.4845 Art.4330N C CNV Art.4845 Art.4303N A C Title: Titolo: Videx Electronics S.p.A. Notes: Via del Lavoro, Monte Giberto (FM) Phone: Fax Note: - info@videx.it 2Vac SE Data creazione: 28/09/206 Data modifica: 28/09/206 Autore: Marco@videx.it Cod.File: 23KVD003F.dwg Foglio / EN - V. - 3/0/6

7 Wall mounting instructions B B A A 35cm C 2 F E C F Fig. Fig. 2 Fig. 3 2 Fig. 4 Fig. 5 Fig. 6. In order to install the videophone, it is necessary to remove the cover, which contains all the electronics, from the base: press lightly on the right part of the videophone and simultaneously pulling outwards the left part as shown in Fig.. 2. Put the base of the unit on the wall at approx 35cm from the finished floor to match the points for the fixing holes A (Fig. 2) remembering that the wires D (Fig. 3) must be fed through the large hole E (Fig. 3). If you use the flush mounting box 503, embed it into the wall vertically at approx. 40cm from the finished floor and the base. 3. Following Fig. 3, make the holes A, insert the wall plugs B and fix the base with the screws C feeding the wires D through the hole E. If you have used the box 503, fix the base to the wall through the holes F using the screws C. 4. As shown in Fig. 4, connect the wires to the removable terminals following the provided installation diagram. Connect the terminal blocks to the electronics contained in the cover as shown in Fig. 5. Test system before closing. Contrast and hue trimmers can be adjusted only if the videophone is open. To activate the display and see changes use the Camera Recall function by pressing button. Note: while testing the system, it is advisable to hold the cover with your hand. 5. Once testing is complete and all the necessary adjustments are made, close the unit as shown in Fig. 6: first hook in the right part and then the left part until you hear a click EN - V. - 3/0/6

8 MANUFACTURER VIDEX ELECTRICS S.P.A. Via del Lavoro, Monte Giberto (FM) Italy Tel (+39) Fax (+39) info@videx.it CUSTOMER SUPPORT All Countries: VIDEX ELECTRICS S.P.A. - technical@videx.it Tel: Fax: UK Customers: VIDEX SECURITY LTD Tech Line: Fax: Main UK office: VIDEX SECURITY LTD Osprey Trinity Park Trinity Way LD E4 8TD Phone: (+44) Fax: (+44) marketing@videx-security.com Northern UK office: VIDEX SECURITY LTD Unit 4-7 Chillingham Industrial Estate Chapman Street NEWCASTLE UP TYNE - NE6 2XX Tech Line: (+44) Phone: (+44) Fax: (+44) Greece office: VIDEX HELLAS Electronics 48 Filolaou Str. 633 ATHENS Phone: (+30) (+30) Fax: (+30) videx@videx.gr Danish office: VIDEX DANMARK Hammershusgade 5 DK-200 COPENHAGEN Phone: (+45) Fax: (+45) videx@videx.dk Benelux office: NESTOR COMPANY NV E3 laan, 93 B-9800 Deinze Phone: (+32) Fax: (+32) info@videx.be Dutch office: NESTOR COMPANY BV Business Center Twente (BCT) Grotestraat, 64 NL-7622 GM Borne info@videxintercom.nl The product is CE marked demonstrating its conformity and is for distribution within all member states of the EU with no restrictions. This product follows the provisions of the European Directives 204/30/EU (EMC); 204/35/EU (LVD); 20/65/EU (RoHS): CE marking 93/68/EEC.

3600 Series Art Digital videophone for VX2200 Digital System ON SW1 SW2 ON SW3 ON Fig. 1 Fig. 2 DE

3600 Series Art Digital videophone for VX2200 Digital System ON SW1 SW2 ON SW3 ON Fig. 1 Fig. 2 DE 161 62 46 178 218 ON SW1 SW2 ON SW3 ON 1 2 3 4 5 678 1 2 3 4 1 2 3 Fig. 1 Fig. 2 DESCRIPTION Intelligent videophone for the VX2200 digital system incorporating a 3,5 full colour active matrix LCD monitor,