- 이 문서는 삼성전자의 기술 자산으로 승인자만이 사용할 수 있습니다 Part Picture Description 5. R emove the memory by pushing the fixed-tap out and Remove the WLAN Antenna. 6. INS

Size: px

Start display at page:

Download "- 이 문서는 삼성전자의 기술 자산으로 승인자만이 사용할 수 있습니다 Part Picture Description 5. R emove the memory by pushing the fixed-tap out and Remove the WLAN Antenna. 6. INS"

아민 빈
6 years ago
Views:

[Caution] Attention to red sentence 3-1.

As shown in picture, adhere Knob to the end closely

(2). 2. Picture when the battery is separated 3.

If only keyboard is disassembled, remove only 2 screws

1 [Caution] Attention to red sentence 3-1. Disassembly and Reassembly R520/ As shown in picture, adhere Knob to the end closely into the arrow direction(1), then push the battery up (2). 2. Picture when the battery is separated 3. Remove the Bottom screw. If only keyboard is disassembled, remove only 2 screws ( ) : M2 X L6, Silver (2EA) : M2 X L2, Black (2EA) : M2 X L8, Black (22EA) 4. Remove the Memory Door ( ) and HDD Door ( )

2 - 이 문서는 삼성전자의 기술 자산으로 승인자만이 사용할 수 있습니다 Part Picture Description 5. R emove the memory by pushing the fixed-tap out and Remove the WLAN Antenna. 6. INSULATOR by lifting the HDD up to about 70 degrees direction. 7. Remove the DVD to the arrow direction as shown in the picture 8. Remove Bottom Screw : M2 X L2, Black (2EA) 3-2

Push the HOOK up inwards by using a pin-set and then

[Caution] Be careful not to scratch on top of the

Lift the top side of the keyboard up carefully as shown

3 - 이 문서는 삼성전자의 기술 자산으로 승인자만이 사용할 수 있습니다 Part Picture Description 9. Push the HOOK up inwards by using a pin-set and then lift the keyboard up. [Caution] Be careful not to scratch on top of the keyboard or LCD panel when you push the hook up. 10. Lift the top side of the keyboard up carefully as shown in the picture 11. Lift the keyboard up, and then take the FPC out after lifting the Connector Lock. 12. Remove the speaker cable connector. 3-3

13. Separate the Touch Pad by pushing the

Separate it by lifting up by holding the

USB sub board, camera, Bluetooth, RJ11).

4 13. Separate the Touch Pad by pushing the connector to the arrow direction 14. Separate it by lifting up by holding the center part of the Top as shown in the Front cover picture. 15. Remove 7 cables (LCD, microphone, DC In, USB sub board, camera, Bluetooth, RJ11). 16. Camera Cable for Tape off when you listen to the will to separate. 3-4

5 17. Cable the status of separation. 18. Separate USB Sub board by removing the screw (2 EA) as shown in the picture. 19. After you remove the Hinge Screw gojeongyong Bottom Lift it up and separate the top LCD Assembly. 20. After separate status LCD Assembly. 3-5

6 21. ODD Sub board board and lift the right to separation. 22. board of the separate 23. ODD Connector Module Connector to separate the lock of the picture (Lock) and then, FFC will detach. 24. WLAN Fixed Screw (1EA) to separate and then in the direction of the arrow. 3-6

25. FAN connector of separate deuleoolrinda Themral module by separating the Screw.

[Caution] Be careful not to make scratch on the LCD Panel when you removing

7 25. FAN connector of separate deuleoolrinda Themral module by separating the Screw. 26. Screw fixed to the left of the CPU contains the following turned up completely separate. 27. Remove the screw (6 EA) after removing Rubber-LCD Cap as shown in the picture. [Caution] Be careful not to make scratch on the LCD Panel when you removing Rubber-LCD Cap. LCD 28. From inside the LCD Front deuleoolrinda carefully. [Caution] If necessary, and to use the LCD on the front namukal geulhimyi to avoid. 3-7

29. Satin in the Hinge Screw Hinge each of the two

LCD Panel to Hinge deuleoolrinda removed from the bottom.

Inverter for CCFL Type LCD Screw 1 EA, so more must be

8 29. Satin in the Hinge Screw Hinge each of the two gaessikeul deuleoolrinda decomposition. 30. LCD Panel to Hinge deuleoolrinda removed from the bottom. LCD 31. Inverter for CCFL Type LCD Screw 1 EA, so more must be separate. When you lift the LCD module should be separate with Inverter. 32. Screw 2 contains a shake up the top of the reinforcement plate. 3-8

9 33. Camera module Camera module and the connector to disconnect the deuleoolrinda. 34. For the cover of the Mic Mic Cable, and then will disconnect. 35. Remove from Camera Cable for LCD Back. TOP 36. LCD Panel LCD Cable disconnect back to back. CCFL Type LCD on top, and the Connector, Inverter-side connector shall be a separation. 3-9

10 LCD 37. LCD Panel LCD Bracket jwawoocheuk Screw for each part to separate the three gaessikeul. 38. Touchpad FFC is separate and the Speaker. TOP 39. Screw 2 EA will take to remove the DC in Jack cable. Bottom 40. The push in the direction of the arrow Hook Lift up separate Bluetooth. 41. Separate RJ11 lifted. 3-10

11 42. After the complete decomposition of Bottom Assembly. Bottom 3-11

12 3-12

6. Separate HDD by pulling in the arrow direction. * Cautions Avoid lifting HDD excessively, because Connector can be damaged ODD Remove

6. Separate HDD by pulling in the arrow direction. * Cautions Avoid lifting HDD excessively, because Connector can be damaged ODD Remove 3-1. Disassembly and Reassembly R510 [Caution] Attention to red sentence. 2 2 1. Before disassembling, the AC adaptor and Battery must be separated. 2. AS mark No.1/2 put KNOB-Battery to end of each side,