KillTest

Transcription

1 KillTest

2 Exam : LAB : Title CCIE-ROUTING AND SWITCHING QUALIFICATION (Lab exam) Version : Demo 1 / 28

3 N1. 2 / 28

4 Part-1 Bridge and Switching 1.1 vtp Sw1/Sw2/Sw3/Sw4 VTP domain:vtp+yy VTP mode:transparent RackYYSw1/SW2/SW3/SW4: 3 / 28

5 vtp domain VTPYY vtp mode transparent that s not need t o use s/ c mode i n VT 1.2 VLAN Sw1: 40 VLAN_BB1 55 VLAN_55 60 VLAN_BB3 100 VLAN_ VLAN_200 Sw2: 50 VLAN_BB2 100 VLAN_ VLAN_200 Sw3 60 VLAN_BB3 200 VLAN_200 Sw4 200 VLAN_200 RackYYSw1: VLAN Name Status Ports 1 default active F0/7,F0/8,F0/9,F0/11,F0/12,F0/13,F0/14Fa0/15,Fa0/17 Fa0/18,Gi0/1,Gi0/2 40 VLAN_BB1 active Fa0/4, Fa0/10 55 VLAN_55 active Fa0/5 60 VLAN_BB3 active Fa0/6 100 VLAN_100 active Fa0/1, Fa0/2 200 VLAN_200 active RackYYSw2: VLAN Name Status Ports 1 default active F0/4,F0/5,F0/7,F0/8,F0/9,F0/11,F0/12,F0/13,F0/14,F0/16,F0/17 F0/18,Gi0/1,Gi0/2 50 VLAN_BB2 active F0/6, F0/ VLAN_100 active F0/1, F0/2 200 VLAN_200 active Po10 4 / 28

6 RackYYSw3: VLAN Name Status Ports 1 default active F0/1,F0/2,F0/3,F0/4 F0/5, F0/6, F0/7,F0/8,F0/9,F0/11,F0/12,F0/13, F0/14, F0/15, F0/16,F0/17,F0/18,Gi0/1,Gi0/2 60 VLAN_BB3 active Fa0/ VLAN_200 active RackYYSw4: VLAN Name Status Ports 1 default active F0/1,F0/2,F0/3,F0/4,F0/5,F0/6,F0/7,F0/8,F0/9,F0/10F0/11,F0/12 F0/13,F0/14,F0/15,F0/16,F0/17,F0/18,Gi0/1,Gi0/2 200 VLAN_200 active Po10 Verify: show vlan brief When u done, u must verify careful. 1.3 Port-channel between Sw1 a Sw2 Sw1 and Sw2 layer 3 Ether channel use port-channel 21 only Assign YY.YY.100.1/24 to Sw1 Port-channel 21 Assign YY.YY.100.2/24 to Sw2 Port-channel 21 ensure interface F0/23 and F0/24 are channel member for both Switch Do not reply on PAgP or LACP to facilitate the connection Verify layer 2 and layer 3 connectivity via the channel link RackYYSw1: interface range FastEthernet0/23-24 shutdown no Switchport channel-group 21 mode on no shutdown interface Port-channel21 ip address YY.YY RackYYSw2: interface range FastEthernet0/23-24 shutdown no Switchport channel-group 21 mode on no shutdown interface Port-channel21 ip address YY.YY Verify: show vtp status; show etherchannel summary; show etherchannel port-channel; 5 / 28

7 1.4 Port-channel between Sw1-Sw3 and Sw2-Sw4 Sw1-Sw3 Sw2-Sw4 layer 2 Ether-channels use port 10 only F0/19 and F0/20 are members of the switches On Sw2 and Sw4 assign all interface in the EC as static-access port on VLAN_200 unconditional enable PAGP to facility the connection verify layer 2 connectivity via the channel link RackYYSw1: interface range FastEthernet0/19-20 shutdown Switchport trunk encapsulation isl Switchport mode trunk channel-group 10 mode desirable no shutdown RackYYSw3: interface range FastEthernet0/19-20 shutdown Switchport trunk encapsulation isl Switchport mode trunk channel-group 10 mode desirable no shutdown RackYYSw2: interface range FastEthernet0/19-20 shutdown Switchport mode access Switchport access VLAN 200 channel-group 10 mode desirable no shutdown RackYYSw4: interface range FastEthernet0/19-20 shutdown Switchport mode access Switchport access VLAN 200 channel-group 10 mode desirable no shutdown Verify: show etherchannel summary; show etherchannel portchannel; Combining the VLAN below, you can see the Sw2 and Sw4 po10 also in VLAN200, before you do on any group - 10 before Switchport access desirable mode or the VLAN 200 VLAN po10 see table. Must be done in the Port. See display any up. 6 / 28

8 1.5 Catalyst layer 3 configuration Configure Sw1 and Sw2 IP address as outlined n diagram Connectivity to R3 uses route ports R1 and R2 are members of vlan 100 on Sw1 and Sw2 1.6 Catalyst layer 3 configuration Configure Sw3 and Sw4 IP addressing Configure VLAN_200 in Sw1 with IP address YY.YY.34.1/24 Configure VLAN_200 in Sw2 with IP address YY.YY.43.1/24 Verify the connectivity between Sw1 and Sw2 RackYYSw1: VLAN 100 YY.YY /24 VLAN 200 YY.YY.34.1/24 RackYYSw2: VLAN 100 YY.YY /24 VLAN 200 YY.YY.43.1/24 RackYYSw3: VLAN 200 YY.YY /24 RackYYSw4: VLAN 200 YY.YY /24 RackYYSw1: ip routing interface VLAN100 ip address YY.YY interface VLAN200 ip address syy.yy RackYYSw2: ip routing interface VLAN100 ip address YY.YY interface VLAN200 ip address YY.YY RackYYSw3: ip routing 7 / 28

9 interface VLAN200 ip address YY.YY RackYYSw4: ip routing interface VLAN200 ip address YY.YY Verify: show ip interface brief; show ip route RackYYSw1: interface FastEthernet0/3 no Switchport ip address YY.YY RackYYSw2: interface FastEthernet0/3 no Switchport ip address YY.YY Verify: show interface status; show ip interface brief; show ip route 1.7Catalyst feature Cofigure Sw1-F0/1 so that the interface will stop forwarding unicast traffic if the input rate exceeds 65 Mbps RackYYSw1: interface Fa0/1 Storm-control unicast level Verify: show storm-control unicast 1.8 Catalyst tunning Cofigure the amount of tine a neighbou should hold CDP information sent by Sw2 before discarding it to 2 minutes RackYYSw1: cdp holdtime 120 Verify: show cdp 1.9 Catalyst Feature F0/5 Configure Sw1 to control and block the flood of unknown Multicast traffic on the interface RackYYSw1: interface Fa0/5 8 / 28

10 Switchport block multicast Ip Igmp snooping Or i p cg mp enabl Verify: show interface interface-id switchport Part-2 IGP and BGP IGP 2.1 OSPF Bbackbones The link between Sw1 and Sw2 All interface in VLAN_100 on Sw1 Sw2 R1 and R2 R3 G0/0 and G0/1 and the fa0/3 on Sw1 and Sw2 Loop back 0 interface on Sw1 Sw2 R2 and R3 Verifying that all OSPF neighbor have built their adjacencies RackYYR1: network YY.YY area 0 network YY.YY area 0 RackYYR2: network YY.YY area 0 network YY.YY area 0 network YY.YY area 0 RackYYSw1: network YY.YY area 0 network YY.YY area 0 network YY.YY area 0 network YY.YY area 0 RackYYSw2: network YY.YY area 0 network YY.YY area 0 network YY.YY area 0 network YY.YY area 0 RackYYR3: network YY.YY area 0 9 / 28

11 network YY.YY area 0 network YY.YY area 0 Verify: show ip ospf interface brief; show ip ospf neighbor 2.2 OSPF over NBMA OSPF area 11 consist of the follow interface and attributes The Frame Relay network between R3 R4 R5 Loop back 0 on R4 and R5 VLAN_55 Ensure there is no DR/BDR RackYYR3: interface s0/0/0.3 ip ospf network point-to-multipoint non-broadcast network YY.YY area 11 nei YY.YY.11.4 nei YY.YY.11.5 RackYYR4: interface s0/0/0.4 ip ospf network point-to-multipoint non-broadcast network YY.YY area 11 network YY.YY area 11 RackYYR5: interface s0/0/0.5 ip os net point-to-multipoint non-broadcast network YY.YY area 11 network YY.YY area 11 network YY.YY area 11 Verify: show ip ospf interface brief; show ip ospf neighbor 2.3 OSPF ASBR and RIP version 2 Configure R4 to receive RIP v2 routes from Backbone 1 When properly configured you will receives RIP v2 routes in the class B address range Z.Z Configure R4 so that the external RIP routes are injected into area 11 and appear throughout that OSPF domain Ensure external routes originates from Autonomous Systems Boundary Routers (ASBR) outside area 11 cannot be flooded within the area 10 / 28

12 Permit OSPF type-3 routes into area 11(Look in R5) RackYYR4: ip prefix-list fbb1 per /16 le 32 Router rip version 2 no auto-summary network distribute-list prefix fbb1 in Fa0/0 redistribute rip metric-type 1 subnets area 11 nssa RackYYR3: area 11 nssa RackYYR5: area 11 nssa Verify: show ip protocol; show ip route rip; show ip ospf; show ip route ospf; 2.4 Area 34 and Area 43 OSPF area 34 consists of the VLAN_200 interfaces on Sw1 and Sw3 and loopback 0 in Sw3 OSPF area 43 consists of the VLAN_200 interfaces on Sw2 and Sw4 and loopback 0 in Sw4 RackYYSw1: network YY.YY area 34 RackYYSw2: network YY.YY area 43 RackYYSw3: network YY.YY area 34 network YY.YY area 34 RackYYSw4: 11 / 28

13 network YY.YY area 43 network YY.YY area 43 Verify: show ip ospf interface brief; show ip ospf neighbor 2.5 OSPF ABR Static routes are not permitted for this question inject a default route into area 0 area 11 area 34 area 43 Use fewest number of steps or commands to completes this RackYYR3: area 11 nssa default-information-originate default-information originate always Verify: show ip route ospf; show ip ospf database 2.6 OSPF Summary Add the following interface on R2 to Area 0 Loopback /24 Loopback /24 Loopback /24 Summarize the above address into a single route Your summary route must be compact and not waste address space Verify the Summary is in the OSPF routing table on R5 and you can ping all the host address R3 Sw 1 Sw2 to make regional summary. RackYYR2: int lo22 ip address int lo32 ip address int lo47 ip address network area 0 Here I choose loopback interface directly in three IOS12.4 versions used after the interface declared ospf support. That fast, and not an error. RackYYR3/Sw1/Sw2: area 0 range Verify; show ip ospf; show ip route ospf; show ip ospf database 12 / 28

14 (If the announcement of OSPF loop, IP add is 24 bits, I use all is point-to-point type) 2.7 RIP version 2 Advertise all the individual YY.YY.0.0 network prefixes generated within your lab topology to backbone 1 Instruct the backbone 1 router that your networks are 5 hops away Filter all other prefixes to backbone 1 1: RackYYR4: Access-list 4 per YY.YY Router rip Redistribute ospf yy metric 1 Offset-list 4 out 4 g0/0 Distribute-list 4 out g0/0 Verify: debug ip rip 2: router rip Redistribute os 8 metric 5 route-map fromospf Route-map fromospf per 10 Match ip add prefix-list fromospf Ip prefix-list fromospf per /16 le 32 Using a heavy distributed orders will solve the three requirements. Our slogan is the strategy to solve the problem with a minimum of job, to minimize CPU consumption. And into the routing database RIP only router rip Redis os 8 route-map fromospf Default-metric 5 Route-map fromosfp per 10 Match ip add fromospf Ip access-list standard fromospf Per router rip Redis os 8 route-map fromospf Route-map fromospf per 10 Set metric 5 Distribute-list prefix fromospf out os 8 Ip prefix-list fromospf per /16 le 32 The source method the worst, To execute the job finished three strategy needs. 2.8 EIGRP EIGRP 100 AS 100 consists of the following interface 13 / 28

15 The Frame Relay network between R1 and R6 Loopback0 on R1 and R6 The BB2 interface on R6 should appear as an external EIGRP route on R1 R6 must have a single 16 bit prefix via R1 to the YY.YY.0.0 network. Do not use route filters or automatic summary Redistribute EIGRP routes into ospf area RackYYR1: Ip prefix-list eto per YY.YY.0.0/16 Route-map eto deny 10 Match ip add pre eto Route-map eto per 20 ip prefix-list ote seq 5 permit /0 route-map ote deny 10 match ip address prefix-list ote route-map ote permit 20 Router eigrp 100 No au Net YY.YY Net YY.YY Redistribute ospf YY metric route-map ote Router os yy Redistribute eigrp 100 subnets metric-type 1 route-map eto Int s0/0/0 Ip summary ei 100 YY.YY RackYYR6: Route-map con per 10 Match interface E0/1 Router eigrp 100 No au Net YY.YY Net YY.YY Redistribute connected route-map CON metric Verify: show ip protocol; show ip route eigrp; show ip route ospf; 2.9 EIGRP over BB3 The backbone 3 router will be sending some class A,B and C IP prefixes 14 / 28

16 Create a prefix-list and apply it so that the EIGRP process will only accept prefixes in the class C address might on the routing table Deny all routes to BB3 (Here should notice first octet= ) Prefix list access list A: /1 le B: /2 le C: /3 le RackYYR6: Ip prefix-list fbb3 per /5 le 32 Ip prefix-list fbb3 per /8 le 32 Ip prefix-list tbb3 deny /0 le 32 Router eigrp 100 Net YY Distribute-list prefix fbb3 in F0/0 Distribute-list prefix tbb3 out F0/0 Verify: show ip protocol; show ip route eigrp 2.10 IPV6 R1 G0/1 2033:YY:YY:21::1 S0/0/0 2033:YY:YY:16::1(FE80::217:94FF:FE15:8C90) R6 f0/1 2033:YY:YY:62::6 S0/3/0 2033:YY:YY:16::6(FE80::215:C6FF:FE4A:6210) All the interface run OSPF v3 RackYYR1#show ipv6 interface brief Gi0/0 [up/up] FE80::ZZZZ:ZZZZ:ZZZZ //link-local address 2038:YY:YY:11::1 Serial0/0/0 [up/up] FE80::ZZZZ:ZZZZ:ZZZZ 2038:YY:YY:61::1 RackYYR6#show ipv6 interface brief Gi0/0 [up/up] FE80::ZZZZ:ZZZZ:ZZZZ 2038:YY:YY:66::6 Serial0/0/0 [up/up] FE80::ZZZZ:ZZZZ:ZZZZ 2038:YY:YY:61::6 15 / 28

17 RackYYR1#show ipv6 route IPv6 Routing Table -7 entries Codes: C -Connected, L -Local, S -Static, R -RIP, B -BGP U -Per-user Static route I1 -ISIS L1, I2 -ISIS L2, IA - ISIS inte area, IS -ISIS summary O - OSPF intr OI - OSPF inter, OE1 - OSPF ext 1, OE2 -OSPF ext 2 ON1 - OSPF NSSA ext 1, ON2 - OSPF NSSA ext 2 C 2038:YY:YY:11::/64 [0/0] via ::, Gi0/0 L 2038:YY:YY:11::1/128 [0/0] via ::, Gi0/0 C 2038:YY:YY:61::/64 [0/0] via ::, Serial0/0/0 L 2038:YY:YY:61::1/128 [0/0] via ::, Serial0/0/0 O 2038:YY:YY:66::/64 [110/65] via FE80::ZZZZ:ZZZZ:ZZZZ, Serial0/0/0 L FE80::/10 [0/0] via ::, Null0 L FF00::/8 [0/0] via ::, Null0 RackYYR6#show ipv6 route IPv6 Routing Table -7 entries Codes: C -Connected, L -Local, S -Static, R -RIP, B -BGP U -Per-user Static route I1 -ISIS L1, I2 -ISIS L2, IA -ISIS inter area, IS -ISIS summary O - OSPF intra, OI - OSPF inter, OE1 - OSPF ext 1, OE2 -OSPF ext 2 ON1 - OSPF NSSA ext 1, ON2 - OSPF NSSA ext 2 O 2038:YY:YY:11::/64 [110/65] via FE80::ZZZZ:ZZZZ:ZZZZ, Serial0/0 C 2038:YY:YY:61::/64 [0/0] via ::, Serial0/0/0 L 2038:YY:YY:61::6/128 [0/0] via ::, Serial0/0/0 C 2038:YY:YY:66::/64 [0/0] via ::, Gi0/0 L 2038:YY:YY:66::6/128 [0/0] via ::, Gi0/0 L FE80::/10 [0/0] via ::, Null0 L FF00::/8 [0/0] via ::, Null0 RackYYR1: ipv6 unicast-routing ipv6 16 / 28

18 Router-id YY.YY.1.1 interface Serial0/0/0 ipv6 address 2033:YY:YY:16::1/64 ipv6 ospf network point-to-point ipv6 ospf 8 area 0 Frame-Relay map ipv6 2038:YY:YY:16::6 106 broadcast Frame-Relay map ipv6 li nk_l oca ± 106 br oadcas interface g0/1 ipv6 address 2033:YY:YY:21::1/64 ipv6 ospf 1 area 0 RackYYR6: ipv6 unicast-routing ipv6 Router-id YY.YY.6.6 interface Serial0/0/0 ipv6 address 2033:YY:YY:16::6/64 ipv6 ospf network point-to-point ipv6 ospf 6 area 0 Frame-Relay map ipv6 2033:YY:YY:16::1 601 broadcast Frame-Relay map ipv6 li nk_l oca ± 601 br oadcas interface g0/1 ipv6 address 2033:YY:YY:62::6/64 Ipv6 ospf 6 area 0 Verify: show ipv6 interface brief; show ipv6 route BGP R1: Loopback 200: 200.1YY.101.1/32 R2: Loopback 200: 200.1YY.102.1/32 R3: Loopback 200: 200.YY.3.1/32 R4: Loopback 200: 200.YY.4.1/32 R5: Loopback 200: 200.YY.5.1/32 R6: Loopback 200: 200.1YY.106.1/ IBGP Configure IBGP as follows AS YY: Configure only R3 R4,and R5 to be part of the AS YY,R3 is the Route-Reflector for this AS AS 1YY:Configure only R1,R2 and R6 to be part of the AS 1YY. Don t confi gur e RR or confederation in the AS You can use any IP address to form the IBGP peers Advertise the loopback 200 on all BGP routers through BGP and make sure you are able to ping these loopbacks from inside each AS 17 / 28

19 Loopback 200: AS YY: 200.YY.X.1/32 AS 1YY:200:1YY.10X.1/32 RackYYR3: Router bgp YY no auto-summary no synchronization bgp Router-id YY.YY.3.3 network 200.YY.3.1 mask neighbor YY.YY.4.4 remote-as YY neighbor YY.YY.4.4 update-source loop0 neighbor YY.YY.4.4 route-reflector-client neighbor YY.YY.5.5 remote-as yy neighbor YY.YY.5.5 update-source loop0 neighbor YY.YY.5.5 route-reflector-client RackYYR4: Router bgp YY no auto-summary no synchronization bgp Router-id YY.YY.4.4 network 200.YY.4.1 mask neighbor YY.YY.3.3 remote-as YY neighbor YY.YY.3.3 update-source Loopback0 RackYYR5: Router bgp YY no auto-summary no synchronization bgp Router-id YY.YY.5.5 network 200.YY.5.1 mask neighbor YY.YY.3.3 remote-as YY neighbor YY.YY.3.3 update-source Loopback0 If use peer - group, configuration is as follows: RACK08R3#router bgp 8 no synchronization bgp router-id bgp log-neighbor-changes network mask neighbor zhenglei peer-group neighbor zhenglei remote-as 8 18 / 28

20 neighbor zhenglei update-source Loopback0 neighbor zhenglei route-reflector-client neighbor peer-group zhenglei neighbor peer-group zhenglei no auto-summary RackYYR1: Router bgp 10YY no auto-summary no synchronization bgp Router-id YY.YY.1.1 network 200.1YY mask neighbor YY.YY.2.2 remote-as 10YY neighbor YY.YY.2.2 update-source Loopback0 neighbor YY.YY.6.6 remote-as 10YY neighbor YY.YY.6.6 update-source Loopback0 RackYYR2: Router bgp 10YY no auto-summary no synchronization bgp Router-id YY.YY.2.2 network 200.1YY mask neighbor YY.YY.1.1 remote-as 10YY neighbor YY.YY.1.1 update-source Loopback0 neighbor YY.YY.6.6 remote as 10YY neighbor YY.YY.6.6 update-source Loopback0 RackYYR6: Router bgp 10YY no auto-summary no synchronization bgp Router-id YY.YY.6..6 network 200.1YY mask neighbor YY.YY.1.1 remote-as 10YY neighbor YY.YY.1.1 update-source Loopback0 neighbor YY.YY.2.2 remote-as 10YY neighbor YY.YY.2.2 update-source Loopback0 Verify: show ip bgp summary; show ip bgp 7.2 EGP Configure EBGP as follows R6 EBGP peers with BB2 IP address YY.254 AS / 28

21 R1 EBGP peers with R3 R2 EBGP peers with R3 You can use any IP address to form the EBGP peers Make sure all routers in AS YY have the EBGP routes from AS 254 via 1YY on their BGP and IP routing tables. You do not need to ping these routes Make sure you are able to ping the loop back 200 from all BGP routers on both AS. You are permitted to use 4 static routes within minimum mask to fulfill this Requirement RackYYR6: Router bgp 10YY neighbor YY.254 remote-as 254 neighbor YY.254 local-as YY no-prepend RackYYR1: Router bgp 10YY neighbor YY.YY.3.3 remote-as YY neighbor YY.YY.3.3 ebgp-multihop 255 neighbor YY.YY.3.3 update-source Loopback0 RackYYR2: Router bgp 10YY neighbor YY.YY.3.3 remote-as YY neighbor YY.YY.3.3 ebgp-multihop 255 neighbor YY.YY.3.3 update-source Loopback0 RackYYR3: Router bgp YY Neighbor YY.YY.1.1 remote-as 10YY Neighbor YY.YY.2.2 remote-as 10YY Neighbor YY.YY.1.1 update-source loop0 Neighbor YY.YY.2.2 update-source loop0 Neighbor YY.YY.1.1 ebgp-multihop 255 Neighbor YY.YY.2.2 ebgp-multihop 255 RackYYSw1: Ip route 200.1YY valn 100 Ip route 200.1yy Y.Y.1.1 RackYYSw2: Ip route 200.1YY valn 100 Ip route 200.1yy Y.Y.1.1 Verify: show ip bgp; ping all lo200 in ASYY and AS1YY 20 / 28

22 7.3 Path Selection Configure R1 so it informs AS YY that the routes 200.1YY and 200.1YY are to preferable be reached via R1 Configure R2 so it informs AS YY,that the routes 200.1YY are to preferable be reached via R2 Route filtering is not permitted, DO NOT change any attributes coming from BGP AS 254 RackYYR1: ; ip prefix-list r2loop seq 5 permit 200.1YY.102.1/32 route-map MED permit 10 match ip address prefix r2loop set metric 100 route-map MED permit 20 Router bgp 10YY neighbor YY.YY.3.3 route-map MED out RackYYR2: ip prefix-list r1r6loop per 200.1yy.101.1/32 ip prefix-list r1r6loop per 200.1yy.106.1/32 route-map MED permit 10 match ip address prefix r1r6loop set metric 100 route-map MED permit 20 Router bgp 10YY neighbor YY.YY.3.3 route-map MED out RackYYR6: Router bgp 10YY Neighbor YY.YY.1.1 send-community Neighbor YY.YY.2.2 send-community RackYYR1: Router bgp 10YY Neighbor YY.YY.2.2 send-community Neighbor YY.YY.3.3 send-community RackYYR2: Router bgp 10YY Neighbor YY.YY.1.1 send-community Neighbor YY.YY.3.3 send-community 21 / 28

23 RackYYR3: Router bgp YY Neighbor YY.YY.4.4 send-community Neighbor YY.YY.5.5 send-community Verify show ip bgp; show ip bgp community Part-3 IP Feature (Multicast eight points, eight points, safety QOS8 points, IP properties eight points, total 32 points) IP IOS feature 3.1 Exception handling Configure R4 to enable exception handling Filename:R4-DUMP Username:ccie Password:cisco Ftp address: YY.254 RackYYR4: ip ftp username ccie ip ftp password cisco exception protocol ftp exception dump150.1.yy.254 exception corefile R4-DUMP 3.2 System logging Buffer alert critical emergencies and error Set the buffer size to 8192 Indicate the date and time for each logged entry RackYYR5: logging on logging buffered 8192 errors clock timezone GMT 8 clock set hh:mm:ss month year service timestamps log datetime local-time year show-timezone Verify: show logging; (All the time is like all equipment in good, I finally see configuration of all the equipment has been a time, and Windows of time) 3.3 DHCP Configure R5 to provide the following parameters for DHCP client on VLAN_55 22 / 28

24 IP address DNS server YY.YY and YY.YY Domain:cisco.com Default gateway Hosts must retain DHCP assigned address 10 days Permit only secure ARP entries to be installed in R5"s ARP table RackYYR5: Service dhcp ip dhcp excluded address YY.YY ip dhcp excluded address YY.YY ip dhcp excluded address YY.YY ip dhcp pool cisco network YY.YY default-router YY.YY dns-server YY.YY YY.YY domain-name ccie.com lease 10 update arp Security 6.1 Tracing Traffic Source to Device under Attack It is suspected that Dos attack is being launched at host YY.254 select an appropriate device to configure so that you can start tracing the source of this attack. Your solution must meet the following criteria The result of the trace must be sent to syslog once a day This device is limited to trace to one IP address only DO NOT configure ACL to achieve this RackYYR5: ip source-track YY.254 ip source-track address-limit 1 ip source-track syslog-interval 1440 Verify: show ip source-track; show ip source-track 6.2 IP Fragment Attacking R4 picked up an BB1 from source is to address, with the attack and destination is a web server: 10.1 y. 5 requirements R4 stop these attacks, and allow the other traffic flow through Rack11R4: ip access-list extended FRAGMENT deny ip any host 10.1.yy.5 fragment permit ip any any 23 / 28

25 int g0/0 ip access-group FRAGMENT in 6.3 Catalyst Security not On Sw1-Fa0/7 configure x authentication meeting the following When clients that do RackYYSw1: aaa new-model aaa authentication dot1x default group radius aaa authorization network default group radius dot1x system-auth-control dot1x guest-vlan supplicant int Fa0/7 Switchport mode access dot1x port-control auto dot1x guest-vlan 55 dot1x host-mode multi-host Verify: show dot1x all; show dot1x interface interface-id details QOS 4.1 Congestion Avoidance Notication Configure R1-S0/0/0 such that is out bound traffic has utilized 75% of total bandwidth. R1 should sign that the network is congested and the recipients need to slow down sending packets. DO NOT configure Frame Relay BECN or FECN for this question RackYYR1: Ip tcp ecn Policy-map QOS class class-default bandwidth percent 75 random-detect random-detect ecn interface s0/0/0 no random-detect service-policy output QOS Verify: show policy-map interface interface-id 4.2 Traffic policing Client on VLAN_BB1 and VLAN_55 access a URL located on VLAN_BB2 frequently. This 24 / 28

26 URL is website.com/directory. Select one suitable router to configure, so as to conserve bandwidth meeting the following criteria. Traffic from this URL back to these clients should not exceed bits per second. If the files download from this URL are image file then drop the traffic You may assume image the names end with the suffix:*.gif*.jpg or *.jpeg RackYYR6: ip cef ip access-list extended TRAFFIC permit ip YY YY permit ip YY YY.YY class-map match-all url match access-group name TRAFFIC match protocol http host match protocol http url /directory /* class-map match-all pic match class-map url match protocol http url *.jpg *.jpeg *.gif policy-map NBAR class pic drop class url police cir interface Gi0/1 service-policy input NBAR ip nbar protocol-discovery Verify: show policy-map interface interface-id 4.3 Discard Eligible and Traffic Shaping The Frame Relay link on R5 is experiencing heavy congesting. Configure R5 so that the Frame Relay provider does not drop any routing protocol packets during congesting and if the number of packets in R5"s Frame Relay interface queue exceeds 10,then the traffic rate will reduced to bps. RackYYR5: access-list 105 deny ospf any any access-list 105 deny tcp any eq 179 any access-list 105 deny tcp any any eq 179 access-list 105 deny pim any any access-list 105 permit ip any any frame-relay de-list 1 protocol ip list 105 interface s0/ / 28

27 frame-relay de-group map-class frame-relay FRTS Frame-Relay adaptive-shaping interface-congestion 10 Frame-Relay mincir interface Serial0/0 Frame-Relay traffic-shaping interface Serial0/0.5 Frame-Relay interface dlci 503 class FRTS Verify: show frame-relay pvc dlci Multicast 5.1 Sparse Mode Multicasting There is a multicast source for group located at VLAN_BB2 and another source for group located at VLAN_BB3.There are clients on VLAN_55 that would like to access these two groups. Configure R5,R3, Sw1,R1 and R6 to meet the following requirements Configure all devices using sparse mode R1 will be the RP for both multicast groups and R3 will be backup RP. Use the most reliable way to achieve this objective and do not configure RP information statically R5 needs to be able to ping both and RackYYR6: ip multicast-routing int g0/1 ip pim sparse-mode ip igmp join-group (This configuration is used) int g0/0 ip pim sparse-mode ip igmp join-group (This configuration is used) int s0/0/0 ip pim sparse-mode ip pim nbma-mode RackYYR1: ip multicast-routing int s0/0/0 ip pim sparse-mode ip pim nbma-mode int g0/0 ip pim sparse-mode int lo200 ip pim sparse-mode 26 / 28

28 ip pim send-rp-ann LO200 sco 10 group-list 11 ip pim send-rp-dis LO200 sco 10 access-list 11 per access-list 11 per RackYYSw1: ip multicast-routing int VLAN 100 ip pim sparse-mode int Fa0/3 ip pim sparse-mode RackYYR3: ip multicast routing int g0/0 ip pim sparse-mode int s0/0/0.3 ip pim sparse-mode ip pim nbma-mode ip pim dr-priority 200 int lo0 ip pim sparse-mode ip pim send-rp-ann Loopback0 sco 10 group-list 33 ip pim send-rp-dis Loopback0 sco 10 access-list 33 permit access-list 33 permit RackYYR5: ip multicast-routing int s0/0/0.5 ip pim sparse-mode ip pim nbma-mode int g0/0 ip pim sparse-mode Verify: show ip pim neighbor; show ip pim rp mapping; R5 ping group addresses and ; 5.2 Defense against Multicast Dos Attack There is a concern that hacker launch Dos attack against R5 with multicast group membership traffic. Configure R5 so that accept only 100 IGMP reports at any time but this limit does not apply to the group / 28

29 RackYYR5: ip access-list extended 105 permit igmp any host int g0/0 ip igmp limit 110 except 105 Verify: show ip igmp interface interface-id 28 / 28