IMPERIAL - ISA Sleeve earings SOLILUE Self-Lubricating, Statically Self-Aligning earings for Extreme Industrial Applications UNIIE SA

Transcription

1 CONTENTS Sleeve earings eatures / enefits Specifi cation/how To Order Nomenclature Selection SOLILUE - Inch SOLILUE - Metric abbitted and ronze-ushed RONZOIL Selection/imensions SOLILUE abbitted ronze-ushed RONZOIL Collars Part Number Index INEX-1 Key Word Index INEX-34 IMPERIAL - ISA UNIIE SA International earings SLEEVOIL Sleeve earing 13-1

2 IMPERIAL - ISA Sleeve earings SOLILUE Self-Lubricating, Statically Self-Aligning earings for Extreme Industrial Applications UNIIE SA International earings Sleeve earing SLEEVOIL Good in temperature extremes and inaccessible locations. Will function effectively in a vacuum. Ideal where bearings are subject to dry cycles or where lube systems would be too costly. Usable in many corrosive (chemical) medias. Will operate in submersible applications of some low viscosity liquids. Recommended for slow speeds and limited shaft movement applications. 13-2

3 Sleeve earings AITTE AN RONZE-USHE EARINGS GOO OR SLOW SPEES AN SHOCK LOAS MPTA LOA RATINGS Cast Iron Housings 2 and 4 olt Housings abbitted Solid or ully Split Housing abbitted earing Surface IMPERIAL - ISA UNIIE SA ronzed-ushed ully Split Housing Replaceable Split ronze ushings rass Locking Spool for Easy ushing Replacement International earings RONZOIL Sleeve earing Self Oiling ushing eeds Oil to Split Pressed Steel Housing Statically Self-Aligning ushing Shoulder Provides Self-Lubricating earing Thrust Surface Slotted olt Holes Oil Resistant Rubber Grommets Available for Sound Isolation and Static Electricity Protection SLEEVOIL 13-3

4 IMPERIAL - ISA UNIIE SA International earings Sleeve earing SLEEVOIL SPECIICATION/ HOW TO ORER Sleeve earings HOW TO ORER SLEEVE EARINGS There are two ways to specify OGE Sleeve earings. Most of the product offering have part numbers with listings shown throughout this catalog. Use of part numbers ensures accurate order processing. When part numbers are not shown, the product may be specifi ed by description or part name. This method is used when ordering units that include modifi cations or options. To order by description, use the nomenclature key shown on page 13-5 and add any special instructions to the end of the description for options not covered by the nomenclature. SOLILUE Statically self-aligning, non-galling, solid-fi lm lubricating for temperature extremes. 700 Series: -40 to Series: -200 to -40 ; 250 to 1, Series: -40 to 800 Also suitable for submerged and limited movement applications. abbitted Grease lubricated for moderate speeds and loads, ambient temperature to 130, babbitt accurately bored to insure even load distribution for conveyor shafts, heavy gear, and chain drives use. ronze-ushed Grease lubricated for moderate speeds, ambient temperature to 300 and heavy loads or shock loads make the advantage of a precision replaceable bronze bushing desirable. Other bushing material is available on a special order basis, such as bronze with graphite plugs, or phenolic resin on nylon. RONZOIL Economical, statically self-aligning, and self-lubricating pillow blocks and four-bolt fl ange units for fans, light machinery, and other general use; ambient temperature to

5 Sleeve earings SLEEVE EARING IMPERIAL - ISA P2 - LT SH MOIICATIONS/EATURES: SH Stainless Steel Housing (Available with SOLILUE LT Series Only) HOUSINGS: STYLE: SHAT SIZE: P2 Pillow lock, 2 olt O RONZOIL 115 irst igit: Number Of Inches ase ASO abbitted Solid Second And Third igit: Sixteenths Of An Inch P4 Pillow lock, 4 olt ASP abbitted Split 115 Indicates 1-15/16 ase AR abbitted Rigid 50M IRST TWO IGITS: ore In Millimeters; 2 lange, 2 olt AA abbitted Angle M : Indicates Metric imension 4 lange, 4 olt AP abbitted Plate HNG Hanger earing ZSP ronze ushed Split NSTU Narrow Slot Take-Up ZR ronze ushed Rigid SCH Screw Conveyor ZA ronze ushed Angle Hanger earing LT7 SOLILUE LT700 Series WSTU Wide Slot Take-Up LT10 SOLILUE LT 1000 Series T Tape ase LT7 SOLILUE Lower acking Height lange racket On Pillow locks or LT700 Series LT10 SOLILUE Lower acking Height On Pillow locks or LT1000 Series LT7NP SOLILUE LT700 Series Nickel Plate LM8 SOLILUE LM800 Series MM7 SOLILUE MM700 Series MM10 SOLILUE MM1000 Series UNIIE SA International earings Sleeve earing SLEEVOIL 13-5

6 IMPERIAL - ISA UNIIE SA International earings Sleeve earing SLEEVOIL Sleeve earings - SOLILUE - Inch Series Too Hot Not Applicable Moisture Tends to Gum Up rg. Too Cold 1000 Series SOLILUE earing Operating Temperature earing Select a bearing from tables for normal loads or loads in limited shaft movement applications having a radial load equal to or greater than the actual load. This simple method is all that is required for the majority of general machine applications using commercial steel shafting and operating in a dry atmosphere. (or more favorable conditions, ratings may be increased somewhat; consult factory). collars may be used for slight amounts of thrust. Generally the rule of 10% of the radial load applies. irty environments will reduce bearing life and should be avoided. Losses due to friction can be as high as 30% depending on speed, lead, temperature and shaft material. ing Commercial steel shafting is good in applications where temperatures do not exceed 700. However, for extended bearing life, at any temperature, the shaft should be hardened to 35 Rockwell C or better. fi nish should be 10 to 20 micro-inches. A fi nish rougher than 20μ will lessen bearing life. A fi nish smoother than 10 will not allow the optimum lubricant fi lm to develop. tolerance should be +.000/-.002 for commercial steel shafting. If using other shaft materials, consult OGE for the shaft tolerance and thermal expansion. When commercial shafting is exposed to a corrosive media, it will oxidize. A rusty shaft will grow in the bearing, thus eliminating clearances. In this case stainless steel shafting may be used and/or provide for regularly scheduled movement of shaft. In elevated temperatures stainless grades such as 17-4, 15-5, or 13-8 are hardenable. s can be spray coated with ceramic or hard chrome. This is good up to about 800. Check with your supplier, since these coatings can fl ake off when the coeffi cient of thermal expansion of the base material differs greatly from that of the coating. High grade specialty shafting may be used in excess of It may be less expensive to use sleeves of this material on more economical shafting. Noise or High Pitched Squeal Carbon-graphite bushings can develop a high frequency vibration in resonance with the operating system to cause noise. ampening or change of resonant frequency of the shaft is required to eliminate noise. Specials SOLILUE bearings or bearings made from alternate bushing materials such as polymers, fi bers, bronze, etc. for unusual operating and load conditions are available on a specially engineered basis by supplying the following: size, material and rpm. Normal load, shock load and frequency. irection of load. Ambient temperature and atmospheric conditions (water, dirt, corrosive, etc.) Type of bearing: pillow block, fl ange bearing, etc. Housing material desired. Quantity. End Closures all earing end Closures are available (3-136). Note: SOLILUE bearings are not designed for rotating housing applications /IMENSIONS PAGE

7 Sleeve earings - SOLILUE - Inch SOLILUE 700, 1000 and 800 Series SOLILUE earing 700 and 1000 Series Radial Load Ratings in Pounds (Normal Loads) Radial Load Ratings in Pounds at various Revolutions per Minute Up to / /8, 15/16, /8, 1-3/ /4, 1-3/8, 1-7/16, 1-1/ /16, 1-3/ /16, / /16, 2-1/ /16, /16, 3-1/ /16, /16, 4-1/ /16, / /8, 15/16, /8, 1-3/ /4, 1-3/8, 1-7/16, 1-1/ /16, 1-3/ /16, / /16, 2-1/ /16, /16, 3-1/ NOTE: The above ratings apply to all base loaded pillow blocks, all cylindrical units and fl ange type bearings (up to 700 ). or fl ange bearings operating at temperatures above 700, cap and side loading of pillow blocks consult Application Engineering. or operations speeds below heave line, use LT1000 and/or hardened shaft. SOLILUE earing Corrosion (Chemical) Resistance earing Series Type of Chemical LM800 Chemical Mineral (Non-Oxidizing) Mineral (Oxidizing) Inorganic Salts (Acid orming) Organic (Strong) Organic (Weak) ph 3-7 Organic Salts (Acid orming) Acids and Acidic Solutions Alkalis (ases & Alkaline Solutions) Gases Salts Solvents Mineral (Non-Oxidizing) Mineral (Oxidizing) Inorganic Salts (ase orming) Organic (Strong) Weak Organic ases ph 7-11 Acid Alkaline (base) Anhydrous (dew Point below -30 ) Cyrogenic (Liquefied) Inert Oxidizing Reducing Good. Not known interaction; compatible Questionable (depends on conditions) Not recommended Acid Salts Alkaline Sales Metals Neutral Salts Neutral Salt Solutions Aliphatic Aromatic Chlorinated, luorinated Oxygenated, Sulfides Note: or compatibility or specifi c chemical, contact Application Engineering 700 and 1000 Series SOLILUE earing Radial Load Rating in Pounds (Limited Movement Applications) Max. Radial Load Max. ase Cap or Side Thrust Loaded Loading 3/ /8, 15/16, /8, 1-3/ /4, 1-3/8, 1-7/16, 1-1/ /16, 1-3/ /16, / /16, 2-1/ /16, 3 12, Use only when shaft movement is limited to approx. ±90º. Movement is infrequent as opposed to continuous and maximum bearing temperature is 700º. LM800 Radial Load Ratings earing Max. Radial ase Load Max. Radial Cap Load 3/ / / Note: These load ratings are to be used only when shaft rotation is less than 10 RPM and temperature does not exceed 800º. Maximum allowable thrust load is 50 lbs. /IMENSIONS PAGE SLEEVOIL Sleeve earing International earings UNIIE SA IMPERIAL - ISA 13-7

8 IMPERIAL - ISA UNIIE SA International earings Sleeve earing SLEEVOIL Sleeve earings - SOLILUE - Metric +370 C -40 C 700 Series Too Hot Not Applicable Moisture Tends to Gum Up rg. Too Cold SOLILUE earing Operating Temperature +537 C +120 C -40 C -128 C 1000 Series earing Select a bearing from tables for normal loads or loads in limited shaft movement applications having a radial load equal to or greater than the actual load. This simple method is all that is required for the majority of general machine applications using commercial steel shafting and operating in a dry atmosphere. (or more favorable conditions, ratings may be increased somewhat; consult factory). collars may be used for slight amounts of thrust. Generally the rule of 10% of the radial load applies. irty environments will reduce bearing life and should be avoided. Losses due to friction can be as high as 30% depending on speed, load, temperature and shaft material. ing Commercial steel shafting is good in applications where temperatures do not exceed 370 C. However, for extended bearing life, at any temperature, the shaft should be hardened to 35 Rockwell C or better. fi nish should be.25 to.50 micro-meters. A fi nish rougher than.50 will lessen bearing life. A fi nish smoother than R a. 25 micro-meters will not allow the optimum lubricant fi lm to develop. tolerance should be +.000/-.051 millimeters for commercial steel shafting. If using other shaft materials, consult OGE for the shaft tolerance and thermal expansion. When commercial shafting is exposed to a corrosive media, it will oxidize. A rusty shaft will grow in the bearing, thus eliminating clearances. In this case stainless steel shafting may be used and/or provide for regularly scheduled movement of shaft. In elevated temperatures stainless grades such as 17-4, 15-5, or 13-8 are hardenable. s can be spray coated with ceramic or hard chrome. This is good up to about 425 C. Check with your supplier, since these coatings can fl ake off when the coeffi cient of thermal expansion of the base material differs greatly from that of the coating. High grade specialty shafting may be used in excess of 537 C. It may be less expensive to use sleeves of this material on more economical shafting. Noise or High Pitched Squeal Carbon-graphite bushings can develop a high frequency vibration in resonance with the operating system to cause noise. ampening or change of resonant frequency of the shaft is required to eliminate noise. Specials SOLILUE bearings or bearings made from alternate bushing materials such as polymers, fibers, bronze, etc. for unusual operating and load conditions are available on a specially engineered basis by supplying the following: size, material and rpm. Normal load, shock load and frequency. irection of load. Ambient temperature and atmospheric conditions (water, dirt, corrosive, etc.) Type of bearing: pillow block, fl ange bearing, etc. Housing material desired. Quantity. End Closures all earing End Closures are available (Page 3-136). Note: SOLILUE bearings are not designed for rotating housing applications /IMENSIONS PAGE

9 Sleeve earings - SOLILUE - Metric SOLILUE EARING 700 and 1000 SERIES SOLILUE earing 700 and 1000 Series Radial Load Ratings in Newtons (N) Normal Loads Series Radial Load Ratings in Newtons at Various Revolutions per Minute mm mm mm mm mm, 45mm mm mm mm, 75mm Series Radial Load Ratings in Newtons at Various Revolutions per Minute mm mm mm mm mm, 45mm mm mm mm, 75mm NOTE: The above ratings apply to all base loaded pillow blocks, all cylindrical units an fl ange type bearings (up to 370 C). or flange bearings operating at temperatures above 370 C, cap and side loading of pillow blocks consult Applications Engineering. or operation speeds below heavy line, use LT1000 and/or hardened shaft. IMPERIAL - ISA UNIIE SA International earings SOLILUE earings 700 Series and 1000 Series Radial Load Ratings in Newtons (N) (Limited Movement Applications) Max. Radial Load Max. Series ase Loaded Cap or Side Loading Thrust Load mm mm mm mm mm, 45mm mm mm mm, 75mm Use only when shaft movement is Limited to approx. ± 90º Movement is infrequent as opposed to continuous and maximum bearing temperature is 370ºC. Sleeve earing SLEEVOIL /IMENSIONS PAGE

10 IMPERIAL - ISA Sleeve earings - abbitted and ronze-ushed General Information UNIIE SA International earings Sleeve earing SLEEVOIL SCOPE-for Stock abbitted and ronze ushed earings, Pillow locks and Take-Ups of the Rigid, Grease Lubricated Type. Important-Referring to Table and Table on the opposite page: Table ratings apply to the following OGE abbitted Sleeve earings: Solid Journals Split abbitted Journals Rigid abbitted Pillow locks Angle abbitted Pillow locks Plate Type lange earings Type H Take-Ups Type A and Take-Ups Table 2 ratings apply to OGE ronze ushed Pillow locks: Split ronze ushed Journals Rigid ronze ushed Pillow locks Angle ronze ushed Pillow locks Note - Ratings do not apply to RONZOIL, Polymer SLEEVOIL or SOLILUE pillow blocks. Reference - lush type reducer bushings to be used with Part Number /8 NPT grease fi tting: Part No. escription /2 x 1/ /8 x 1/ /8 x 1/ /4 x 1/ /2 x 1/4 Selection - Select a bearing from rating tables having a radial load equal to or greater than the Actual Radial Load, provided that operating conditions numbered 1 thru 7, at right, are met. If these conditions cannot be met, select a bearing for an Equivalent Radial Load to be obtained by multiplying the Actual Radial Load by a service factor depending on the specifi c application. Use a factor of up to 2.0 for areas in the rating table to the left of the zigzag line. Use a factor of up to 3.0 for areas to the right of the zigzag line. Load ratings are based on industry standard ratings established by the Mechanical Power Transmission Association. (Standard No. 401) Operating Conditions 1. Maintain adequate grease lubrication. 2. Maintain proper bearing alignment for uniform distribution of load under all operating conditions. 3. Normal running loads must not exceed ratings shown in the load tables. Starting and occasional peak loads should not exceed ratings by more than 100%. 4. irection of load should not be closer than 30 to grease groove or closer than 30 to the joint between cap and base. If direction of load falls within this area which is not recommended, decrease maximum load by 50%. 5. The shaft journal surface fi nish must be equal to that of commercial steel shafting (about 32 micro inches) and the diameter within the tolerances of commercial steel shafting (+.000 / -.002) 6. Ambient temperature should not exceed 130 for babbitted and 300 for bronze-bushed bearings. If the shaft transmits heat from a source such as an oven, the shaft temperature at the bearing should not exceed these ambient temperatures. 7. earings should be protected against adverse operating conditions. /IMENSIONS PAGE

11 Sleeve earings - abbitted and ronze-ushed Radial Load Ratings (Refer To Instructions On Opposite Page) Table 1: MPTA Radial Load Ratings for abbitted Sleeve earings Radial Load Rating in Lbs. at Various Revolutions Per Minute s / / / / / / /16, 1-1/ /16, 1-3/ /16, 1-1/ /16, 1-3/ /16, /16, 2-1/ /16, 2-1/ /16, 2-3/ /16, /16, 3-1/ /16, /16, 4-1/ /16, /16, /16, /16, 6-1/ /16, /16, 7-1/ /16, or speeds lower than 10 rpm consult OGE. Table 2: MPTA Radial Load Ratings for ronze ushed Sleeve earings Radial Load Rating in Lbs. at Various Revolutions Per Minute s / / / / / / /16, 1-1/ /16, 1-3/ /16, 1-1/ /16, 1-3/ /16, /16, 2-1/ /16, 2-1/ /16, 2-3/ /16, /16, 3-1/ /16, /16, 4-1/ /16, /16, 5-1/ /16, /16, 6-1/ /16, /16, 7-1/ or speeds lower than 10 rpm consult OGE. 7-15/16, SLEEVOIL Sleeve earing International earings UNIIE SA IMPERIAL - ISA /IMENSIONS PAGE

12 IMPERIAL - ISA Sleeve earings - ronze ushings UNIIE SA International earings Sleeve earing SLEEVOIL Lower half of new bushing is installed by relieving shaft pressure, prying out old bushing and rolling in new one. or Split ronze ushed Journal earings. or Rigid ronze ushed Pillow locks. or Angle ronze ushed Pillow locks. These precision bushings are machined from quality cast cylinders of high grade leaded bronze. They are furnished in matched halves and sold in complete sets only. Grease grooves are provided in the top half for proper lubrication. ushings are designed to be installed in the bearings listed above without removing the shaft or bearing base. A brass locking spool positions the bushing preventing lateral movement or rotation. This simple method minimizes down time and labor costs. They are particularly suited for heavy loads, elevated temperatures and corrosive conditions. ushings made of special alloys can be furnished where especially diffi cult heat problems may arise. They will be priced on application. ronze ushing Sets New bushing upper half is easily dropped into bearing cap. Grease grooves in the top of bore offer adequate lubrication. Locking ushing Sets Spools* Part Part Wt. No. No. 1-15/ / / / / / / / / / / / / or other bushing material consult OGE Price is for one bushing set which includes upper and lower half * Order separately if desired /IMENSIONS PAGE

13 Sleeve earings - RONZOIL RAIAL LOA RATINGS OR RONZOIL SLEEVE EARINGS s Radial Load Rating in Lbs. at Various Revolutions Per Minute / / / / / / / Radial Load Rating in Lbs. at Various Revolutions Per Minute s / / / / / / / RONZOIL Take-Up earing Assembly (TUO--) Assy.No / / / / / Select a bearing from the rating tables having a radial load equal to or greater than the actual load providing normal operating conditions are met. If these conditions cannot be met, select a bearing for an equivalent radial load to be obtained by multiplying the actual radial load by a 2.0 to 4.0 service factor-depending on specifi c application. Normal Operating Conditions: 1. Adequate oil supply. 2. Proper bearing alignment for uniform distribution of load at all operating conditions. 3. No shock loading. 4. No adversely high operating conditions. 5. No moist, corrosive, or abrasive atmosphere. 6. surface fi nish must be equal to that of commercial steel shafting. (About 32 micro inches) 7. diameter tolerance within +.000/ Maximum operating temperature 180. SLEEVOIL Sleeve earing International earings UNIIE SA IMPERIAL - ISA /IMENSIONS PAGE

14 IMPERIAL - ISA /IMENSIONS Sleeve earings - SOLILUE 3/4 THRU 3 SOLILUE LT PILLOW LOCKS A G J L UNIIE SA International earings Sleeve earing SLEEVOIL Series MAXIMUM MINIMUM 700 SERIES 1000 SERIES Used on Part Number escription Wt. Part Number escription Wt. rame 204 3/ P2-LT P2-LT L-10 20mm P2-LT7-20M P2-LT10-20M 0.77 L-10 7/ P2-LT P2-LT / P2-LT P2-LT L P2-LT P2-LT mm P2-LT7-25M P2-LT10-25M 0.64 L / P2-LT P2-LT / P2-LT P2-LT L-20 30mm P2-LT7-30M P2-LT10-30M 1.22 L / P2-LT P2-LT / P2-LT P2-LT / P2-LT P2-LT L / P2-LT P2-LT mm P2-LT7-35M P2-LT10-35M 1.77 L / P2-LT P2-LT / P2-LT P2-LT L-20 40mm P2-LT7-40M P2-LT10-40M mm P2-LT7-45M P2-LT10-45M 2.63 L / P2-LT P2-LT P2-LT P2-LT L-30 50mm P2-LT7-50M P2-LT10-50M 3.08 L / P2-LT P2-LT L / P2-LT P2-LT / P2-LT P2-LT L-40 60mm P2-LT7-60M P2-LT10-60M 4.58 L / P2-LT P2-LT P2-LT P2-LT L-45 70mm P2-LT7-70M P2-LT10-70M mm P2-LT7-75M P2-LT10-75M 9.62 L-45 H M C 13-14

15 /IMENSIONS Sleeve earings - SOLILUE 3/4 THRU 3 SOLILUE LT PILLOW LOCKS IMPERIAL - ISA UNIIE SA Series A C Min. Max. olt ia. G H J L M International earings Sleeve earing SLEEVOIL 204 3/ /4 1-11/32 3-3/8 4-3/16 3/8 27/32 17/32 2-9/16 1-3/8 1-5/16 20mm / /16 1-1/16 5-1/2 1-13/ /16 4-1/2 3/8 27/32 19/ /32 1-9/16 1-7/ mm / /16 1-3/16 6-1/4 1-3/4 4-1/4 5 1/2 15/16 11/16 3-1/4 1-13/16 1-5/8 30mm /4 1-3/ /16 1-1/2 35mm 1-5/ / / / / / / / / / / /16 1-3/4 1-9/16 7-7/ /2 6-3/16 1/2 29/32 3/4 4-9/32 2-9/16 2-1/8 40mm 45mm / /8 8-1/8 2-1/ /16 5/8 1-1/32 3/4 4-17/ /16 2-1/4 50mm /16 1-3/4 8-7/8 2-5/16 6-3/8 7-7/16 5/8 1-7/32 7/8 4-31/32 3-1/8 2-1/2 2-7/ /2 1-13/16 9-1/2 2-3/8 6-7/8 7-15/16 5/8 1-7/32 7/8 5-13/32 3-1/2 2-3/4 60mm / / /4 2-7/8 8-1/2 9-1/2 7/8 1-7/ /4 3-15/16 3-1/2 70mm 75mm All imensions Are In Millimeters Unless Otherwise Specifi ed The LT and LT Pillow locks Are Identical Except the LT Pillow locks Have Lower acking imensions 13-15

16 IMPERIAL - ISA /IMENSIONS Sleeve earings - SOLILUE 3/4 THRU 3 SOLILUE LT PILLOW LOCKS A G J L UNIIE SA International earings Sleeve earing SLEEVOIL Series MINIMUM MAXIMUM H 700 SERIES 1000 SERIES Used on Part No. escription Wt. Part No. escription Wt. rame 204 3/ P2-LT P2-LT L-10 20mm P2-LT7-20M P2-LT10-20M 0.73 L-10 7/ P2-LT P2-LT / P2-LT P2-LT L P2-LT P2-LT mm P2-LT7-25M P2-LT10-25M 0.59 L / P2-LT P2-LT / P2-LT P2-LT L-20 30mm P2-LT7-30M P2-LT10-30M 1.18 L / P2-LT P2-LT / P2-LT P2-LT / P2-LT P2-LT L / P2-LT P2-LT mm P2-LT7-35M P2-LT10-35M 1.72 L / P2-LT P2-LT / P2-LT P2-LT L-20 40mm P2-LT7-40M P2-LT10-40M mm P2-LT7-45M P2-LT10-45M 2.18 L / P2-LT P2-LT P2-LT P2-LT L-30 50mm P2-LT7-50M P2-LT10-50M 2.72 L / P2-LT P2-LT L / P2-LT P2-LT / P2-LT P2-LT L-40 60mm P2-LT7-60M P2-LT10-60M 3.67 L / P2-LT P2-LT P2-LT P2-LT L-45 70mm mm L-45 M C 13-16

17 /IMENSIONS Sleeve earings - SOLILUE 3/4 THRU 3 SOLILUE LT PILLOW LOCKS IMPERIAL - ISA UNIIE SA Series A C Min. Max. olt ia. G H J L M International earings Sleeve earing SLEEVOIL 204 3/ /4 1-11/32 3-3/8 4-3/16 3/8 27/32 15/32 2-1/2 1-3/8 1-1/4 20mm / /16 1-1/16 5-1/2 1-13/ /16 4-1/2 3/8 27/32 15/ /32 1-9/16 1-5/ mm / /16 1-3/16 6-1/4 1-3/4 4-1/4 5 1/2 15/16 5/8 3-3/ /16 1-9/16 30mm /4 1-3/ /16 1-1/2 35mm 1-5/ / / / / / / / / / / /16 1-3/4 1-9/16 7-7/ /2 6-3/16 1/2 29/32 11/16 4-7/32 2-9/16 2-1/16 40mm 45mm / /8 8-1/8 2-1/ /16 5/8 1-1/32 11/ / /16 2-3/16 50mm /16 1-3/4 8-7/8 2-5/16 6-3/8 7-7/16 5/8 1-7/32 13/ /32 3-1/8 2-7/16 2-7/ /2 1-13/16 9-1/2 2-3/8 6-7/8 7-15/16 5/8 1-7/32 13/ /32 3-1/2 2-11/16 60mm / / /4 2-7/8 8-1/2 9-1/2 7/8 1-7/16 1-1/16 6-9/ /16 3-5/16 70mm 75mm All imensions Are In Millimeters Unless Otherwise Specifi ed The LT and LT Pillow locks are Identical Except the LT Pillow locks Have Lower backing imensions

18 IMPERIAL - ISA /IMENSIONS Sleeve earings - SOLILUE 3-7/16 THRU 5 SOLILUE MM PILLOW LOCKS P A UNIIE SA International earings Sleeve earing SLEEVOIL 700 Series 1000 Series Part No. escription Part No. escription Wt. 3-7/ P2-MM P2-MM / P2-MM P2-MM / P2-MM P2-MM P2-MM P2-MM / P2-MM P2-MM / P2-MM P2-MM / P4-MM P4-MM P4-MM P4-MM /16 3-1/2 3-15/ /16 4-1/2 4-15/ olt ase 4 olt ase olt olt Min. Max. ia. E ia. Used On rame A C H / /16 H /16 3-3/16 H / /16 H /16 4-3/4 G H J L M P 9-1/4 10-1/4 5/ /4 1-3/ /8 3-1/4 7-1/4 9-7/8 11-1/2 3/ / /16 5-5/8 3-3/4 8-3/ / /16 7/ /2 2-1/4 9-7/ /16 4-1/ /8 14-3/ /4 1-11/16 2-3/4 10-1/2 7-9/ /8 No Published Metric imensions or This Product (MIN.-MAX.) G M H J L C E 13-18

19 /IMENSIONS Sleeve earings - SOLILUE 3-7/16 THRU 5 SOLILUE MM 4-OLT LANGE EARINGS IMPERIAL - ISA L UNIIE SA 700 Series 1000 Series Part No. escription Part No. escription Wt. 3-7/ MM MM / MM MM / MM MM MM MM / MM MM / MM MM / MM MM MM MM /16 3-1/2 3-15/ /16 4-1/2 4-15/16 5 A C E G H L 3-1/2 7-5/8 2-59/64 6 3/16 5/8 8-9/16 5/8 4-7/ /8 3-11/32 6-7/8 1/4 3/4 9-1/2 11/16 5-5/8 4-1/2 10-1/4 3-23/32 8-1/8 1/4 7/8 11-3/8 3/4 6-15/ /16 4-5/8 9-3/16 1/ /8 13/16 7-9/16 No Published Metric imensions or This Product G C A H E International earings Sleeve earing SLEEVOIL 13-19

20 IMPERIAL - ISA /IMENSIONS Sleeve earings - SOLILUE 3/4 THRU 2 SOLILUE LT 2-OLT LANGE EARING M N C A UNIIE SA International earings Sleeve earing SLEEVOIL Series Series 1000 Series Part No. escription Wt. Part No. escription Wt. 3/ LT LT mm LT7-20M LT10-20M / LT LT / LT LT LT LT mm LT7-25M LT10-25M / LT LT / LT LT mm LT7-30M LT10-30M / LT LT / LT LT / LT LT / LT LTI mm LT7-35M LT10-35M / LT LT / LT LT mm LT7-40M LT10-40M mm LT7-45M LT10-45M / LT LT LT LT mm LT7-50M LT10-50M 2.36 L J H 13-20

21 /IMENSIONS Sleeve earings - SOLILUE 3/4 THRU 2 SOLILUE LT 2-OLT LANGE EARING IMPERIAL - ISA UNIIE SA Series A C olt H J L M N ia. 3/4 29/ /16 1-1/8 3-17/32 3/8 1/2 5/32 1-3/8 2-3/8 1-1/2 20mm / /8 International earings Sleeve earing SLEEVOIL 15/ mm 63/ / / / /16 7/16 1/ / / / / /8 1-3/16 1-7/64 5-9/16 1-7/ /32 7/16 1/2 5/ /16 3-1/8 1-9/16 30mm / /4 1-3/8 1-7/16 1-7/32 6-1/8 1-3/8 5-1/8 1/2 9/16 5/32 2-1/8 3-3/4 1-27/32 1-1/2 35mm / /16 1-3/4 1-21/64 7-1/I6 1-19/ /32 1/2 5/8 3/16 2-9/16 4-3/8 1-29/32 40mm 45mm / / /32 7-7/ /32 6-3/16 1/2 5/8 3/ /16 4-9/32 2-1/32 50mm /

22 IMPERIAL - ISA /IMENSIONS Sleeve earings - SOLILUE 3/4 THRU 3 SOLILUE LT 4-OLT LANGE EARING C A L UNIIE SA International earings Sleeve earing SLEEVOIL Series Series 1000 Series Part No. escription Wt. Part No. escription Wt. 3/ LT LT mm LT7-20M LT10-20M 0.6 7/ LT LT / LT LT LT LT mm LT7-25M LT10-25M / LT LT / LT LT mm LT7-30M LT10-30M / LT LT / LT LT / LT LT / LT LT mm LT7-35M LT10-35M / LT LT / LT7-I LT mm LT7-40M LT10-40M mm LT7-45M LT10-45M / LT LT LT LT mm LT7-50M LT10-50M / LT LT / LT LT / LT LT mm LT7-60M LT10-60M / LT LT LT LT mm LT7-70M LT10-70M mm LT7-75M LT10-75M 8.03 J H 13-22

23 /IMENSIONS Sleeve earings - SOLILUE 3/4 THRU 3 SOLILUE LT 4-OLT LANGE EARING IMPERIAL - ISA Series 204 A C olt H J L 3/4 29/32 3-3/8 1-1/8 2-1/2 3/8 7/16 5/32 1-3/8 20mm / /16 63/64 3-3/4 1-1/8 2-3/4 7/16 1/2 3/16 1-9/ mm / /16 31/32 4-1/4 1-7/32 3-1/4 7/16 1/2 5/ /16 30mm /4 1-3/ /16 1-7/32 4-3/4 1-3/8 3-5/8 1/2 9/16 5/32 2-1/8 1-1/2 35mm /16 1-3/4 1-11/32 5-3/8 1-19/32 4-1/8 1/2 5/8 13/64 2-9/16 40mm 45mm / /32 5-5/8 1-21/32 4-3/8 1/2 5/8 7/ /16 50mm / /32 6-1/2 1-25/32 5-1/8 5/8 11/16 7/32 3-1/8 2-7/ /2 1-15/ /32 5-5/8 5/8 11/16 11/64 3-1/2 60mm / /32 7-3/4 2-3/4 6 3/4 1 17/ /16 70mm 75mm All imensions Are in Millimeters Unless Otherwise Specifi ed. SLEEVOIL Sleeve earing International earings UNIIE SA 13-23

24 IMPERIAL - ISA /IMENSIONS Sleeve earings - SOLILUE 3/4 THRU 2-1/2 SOLILUE LT NARROW SLOT TAKE-UP EARINGS UNIIE SA International earings Sleeve earing SLEEVOIL Series LT700 LT1000 Used Part No. escription Wt. Part No. escription Wt. on rame 3/ NSTU-LT NSTU-LT NS mm NSTU-LT7-20M NSTU-LT10-20M 0.77 WS-300 7/ NSTU-LT NSTU-LT / NSTU-LT NSTU-LT NSTU-LT NSTU-LT NS mm NSTU-LT7-25M NSTU-LT10-25M 0.77 WS / NSTU-LT NSTU-LT / NSTU-LT NSTU-LT NS mm NSTU-LT7-30M NSTU-LT10-30M 1.22 WS / NSTU-LT NSTU-LT / NSTU-LT NSTU-LT / NSTU-LT NSTU-LT / NSTU-LT NSTU-LT NS mm NSTU-LT7-35M NSTU-LT10-35M 1.36 WS / NSTU-LT NSTU-LT / NSTU-LT NSTU-LT mm NSTU-LT7-40M NSTU-LT10-40M mm NSTU-LT7-45M NSTU-LT10-45M / NSTU-LT NSTU-LT NSTU-LT NSTU-LT NS-400 WS-400 NS mm NSTU-LT7-50M NSTU-LT10-50M 2.4 WS / NSTU-LT NSTU-LT NS / NSTU-LT NSTU-LT / NSTU-LT NSTU-LT NS mm NSTU-LT7-60M NSTU-LT10-60M 3.18 WS

25 /IMENSIONS Sleeve earings - SOLILUE 3/4 THRU 2-1/2 SOLILUE LT NARROW SLOT TAKE-UP EARINGS IMPERIAL - ISA Series A C E Screw ia. G 204 3/ /2 1/4 1-1/2 2-3/16 3/4 7/16 20mm / /8, 15/16, 1 1-1/16 3-9/16 1/4 1-1/2 2-3/16 3/4 7/16 25mm / / /16 1-3/16 4-5/16 1/4 2-1/2 2-11/16 3/4 7/16 30mm / /4, 1-3/8, /16, 1-1/2 1-5/16 4-1/2 1/4 2-1/2 2-11/16 3/4 7/16 35mm / /16, 1-3/4 1-9/16 5-7/16 5/ /4 7/8 1/ mm 45mm / /16, 2 1-5/8 5-1/2 5/ /4 7/8 1/2 50mm / /16 1-3/4 6-1/8 5/16 3-1/2 3-5/8 1 19/ /16, 2-1/2 1-13/ /16 5/16 3-3/4 3-7/8 1 19/32 60mm UNIIE SA International earings Series H J L M N P Pin ia /4 7/8 1-3/8 1-3/8 2-5/8 3-1/8 5/16 20mm / /8, 15/16, 1 7/8 1-3/8 1-9/16 2-5/8 3-1/8 5/16 25mm /16 1-1/ /16 15/16 1-3/8 1-13/16 3-1/2 4-1/8 5/16 30mm /16 1-1/4, 1-3/8, /16, 1-1/2 15/16 1-3/8 2-1/8 3-1/2 4-1/8 5/16 35mm / /16, 1-3/4 1-7/32 1-5/8 2-9/ /4 3/ mm 45mm / /16, 2 1-3/32 1-5/8 2-13/ /4 3/8 50mm / /16 1-9/32 1-5/8 3-1/2 4-15/16 5-3/4 7/ /16, 2-1/2 1-9/32 1-3/4 3-1/8 4-7/16 5-3/8 7/16 60mm /16 Sleeve earing SLEEVOIL 13-25

26 IMPERIAL - ISA /IMENSIONS Sleeve earings - SOLILUE 3/4 THRU 3 SOLILUE LT WIE SLOT TAKE-UP EARINGS T K J M N L UNIIE SA International earings Sleeve earing SLEEVOIL Series LT700 LT1000 Used on Part No. escription Wt. Part No. escription Wt. rame 3/ WSTU-LT WSTU-LT WS mm WSTU-LT7-20M WSTU-LT10-20M 1.09 WS-300 7/ WSTU-LT WSTU-LT / WSTU-LT WSTU-LT WSTU-LT WSTU-LT WS mm WSTU-LT7-25M WSTU-LT10-25M 1.09 WS / WSTU-LT WSTU-LT / WSTU-LT WSTU-LT WS mm WSTU-LT7-30M WSTU-LT10-30M 1.41 WS / WSTU-LT WSTU-LT / WSTU-LT WSTU-LT / WSTU-LT WSTU-LT / WSTU-LT WSTU-LT WS mm WSTU-LT7-35M WSTU-LT10-35M 1.77 WS / WSTU-LT WSTU-LT / WSTU-LT WSTU-LT mm WSTU-LT7-40M WSTU-LT10-40M mm WSTU-LT7-45M WSTU-LT10-45M / WSTU-LT WSTU-LT WSTU-LT WSTU-LT WS-400 WS-400 WS mm WSTU-LT7-50M WSTU-LT10-50M 2.95 WS / WSTU-LT WSTU-LT WS E H G 2-7/ WSTU-LT WSTU-LT / WSTU-LT WSTU-LT WS mm WSTU-LT7-60M WSTU-LT10-60M 4.58 WS / WSTU-LT WSTU-LT WSTU-LT WSTU-LT mm WSTU-LT7-70M WSTU-LT10-70M mm WSTU-LT7-75M WSTU-LT10-75M 5.67 C A WS-515 WS

27 /IMENSIONS Sleeve earings - SOLILUE 3/4 THRU 3 SOLILUE LT WIE SLOT TAKE-UP EARINGS IMPERIAL - ISA Series A C E ia. G 204 3/ /16 17/ /8 3/4 3/8 20mm / /8, 15/16, 1 1-1/ /16 17/ /16 13/16 3/8 25mm / /8, 1-3/16 1-3/16 4-3/8 17/32 2-1/4 2-3/4 7/8 3/8 30mm / /4, 1-3/ /16, 1-1/2 1-5/16 4-7/8 17/32 2-1/2 3-1/16 7/8 1/2 35mm / /16,1-3/4 1-9/16 5-5/8 11/16 3-1/4 3-7/16 1-1/8 5/8 40mm, 45mm / /16, 2 1-5/8 5-13/16 11/16 3-3/8 3-9/16 1-1/8 5/8 50mm / /16 1-3/4 6-11/16 1-1/16 3-3/4 4-3/16 1-3/8 3/ /16, 2-1/2 1-13/16 7-1/2 1-1/ /16 1-3/8 3/4 60mm / /16, /32 9-1/8 1-1/16 4-3/4 5-1/2 1-9/16 13/16 70mm, 75mm / UNIIE SA International earings Series H J K L M N T 204 3/4 5/ /4 1-3/ /8 1-3/8 20mm /8, 15/16, 1 5/ /16 1-9/ /8 1-3/8 25mm /8, 1-3/16 5/8 2-3/16 1-7/ /16 3-1/2 4-1/8 1-5/8 30mm /4, 1-3/ /16, 1-1/2 5/8 2-1/2 1-7/16 2-1/8 3-1/2 4-1/8 1-5/8 35mm /16,1-3/4 3/4 3-1/4 1-15/16 2-9/ /4 1-15/16 40mm, 45mm /16, 2 3/4 3-1/4 1-15/ / /4 1-15/16 50mm / /2 3-1/8 5-1/8 5-7/8 2-1/ /16, 2-1/2 1-1/ /2 3-1/2 5-1/8 5-7/8 2-1/2 60mm /16, 3 1-1/4 4-3/8 2-3/4 3-15/ / /16 2-3/4 70mm, 75mm Sleeve earing SLEEVOIL 13-27

28 IMPERIAL - ISA /IMENSIONS Sleeve earings - SOLILUE 1-15/16 THRU 3 TYPE GLT SOLILUE TAKE-UP EARINGS UNIIE SA International earings Sleeve earing SLEEVOIL 700 Series 1000 Series Part No. escription Part No. escription 1-15/ TP-GLT TP-GLT TP-GLT TP-GLT Wt. rame 10.1 TP10 2-3/ TP-GLT TP-GLT TP20 2-7/ TP-GLT TP-GLT / TP-GLT TP-GLT / TP-GLT TP-GLT TP-GLT TP-GLT TP TP

29 /IMENSIONS Sleeve earings - SOLILUE 1-15/16 THRU 3 TYPE GLT SOLILUE TAKE-UP EARINGS SLEEVOIL International earings UNIIE SA IMPERIAL - ISA 1-15/16 2 A C E J L T 1-5/8 6-1/2 2-3/ /4 6-3/8 2-13/16 2-3/8 2-3/16 1-3/ /2 6-3/4 3-3/8 6-7/8 3-1/8 2-3/8 2-7/16 2-1/2 2-15/ /16 7-1/2 2-3/ /2 7-7/16 3-1/2 2-3/4 2-23/32 8-1/2 2-1/ / /16 2-3/4 Sleeve earing 13-29

30 IMPERIAL - ISA /IMENSIONS Sleeve earings - SOLILUE 3/4 THRU 3 SOLILUE LT INSERTS UNIIE SA International earings Sleeve earing SLEEVOIL Series Part No. 700 Series 1000 Series LT700 Series escription Wt. Part No. LT1000 Series escription 3/ INS-LT INS-LT mm INS-LT7-20M INS-LT10-20M / INS-LT INS-LT / INS-LT INS-LT INS-LT INS-LT mm INS-LT7-25M INS-LT10-25M / INS-LT INS-LT / INS-LT INS-LT mm INS-LT7-30M INS-LT10-30M / INS-LT INS-LT / INS-LT INS-LT / INS-LT INS-LT / INS-LT INS-LT mm INS-LT7-35M INS-LT10-35M / INS-LT INS-LT / INS-LT INS-LT mm INS-LT7-40M INS-LT10-40M mm INS-LT7-45M INS-LT10-45M / INS-LT INS-LT INS-LT INS-LT mm INS-LT7-50M INS-LT10-50M / INS-LT INS-LT / INS-LT INS-LT / INS-LT INS-LT mm INS-LT7-60M INS-LT10-60M / INS-LT INS-LT INS-LT INS-LT mm INS-LT7-70M INS-LT10-70M mm INS-LT7-75M INS-LT10-75M Wt