CDX-GT522U/CDX-GT520U

Transcription

1 (1) FM/AM Compact Disc Player Operating Instructions GB KR To switch the FM/AM tuning step, see page 4. To cancel the demonstration (DEMO) display, see page 4. CDX-GT522U/CDX-GT520U

2 Be sure to install this unit in the dashboard of the car for safety. For installation and connections, see the supplied installation/connections manual. Laser Diode Properties Emission Duration: Continuous Laser Output: Less than 53.3μW (This output is the value measurement at a distance of 200 mm from the objective lens surface on the Optical Pick-up Block with 7 mm aperture.) Warning if your car s ignition has no ACC position Be sure to set the Auto Off function (page 15). The unit will shut off completely and automatically in the set time after the unit is turned off, which prevents battery drain. If you do not set the Auto Off function, press and hold until the display disappears each time you turn the ignition off. ZAPPIN and Quick-BrowZer are trademarks of Sony Corporation. Windows Media is either a registered trademark or trademark of Microsoft Corporation in the United States and/or other countries. This product contains technology subject to certain intellectual property rights of Microsoft. Use or distribution of this technology outside of this product is prohibited without the appropriate license(s) from Microsoft. MPEG Layer-3 audio coding technology and patents licensed from Fraunhofer IIS and Thomson. Android is a trademark of Google Inc. Use of this trademark is subject to Google Permissions. Note on the lithium battery Do not expose the battery to excessive heat such as direct sunlight, fire or the like. 2

3 Table of contents Getting Started Switching the FM/AM tuning step Canceling the DEMO mode Setting the clock Detaching the front panel Location of controls Main unit RM-X211 Remote commander Radio Storing and receiving stations RDS CD Playing a disc USB devices Playing back a USB device Searching and playing tracks Playing tracks in various modes Searching a track by name Quick-BrowZer Searching a track by listening to track passages ZAPPIN Sound Settings and Setup Menu Enjoying sophisticated sound functions Advanced Sound Engine Adjusting setup items Using optional equipment Auxiliary audio equipment Additional Information Precautions Maintenance Specifications Troubleshooting

4 Getting Started Switching the FM/AM tuning step The FM/AM tuning step is factory-set to the 50 khz (FM)/9 khz (AM) position. If the frequency allocation system of your country is based on 200 khz (FM)/10 khz (AM) or 100 khz (FM)/10 khz (AM) step, set the tuning step before use. This setting appears when this unit is turned off. 1 Press, rotate the control dial until GENERAL appears, then press it. 2 Rotate the control dial until TUNER- STP appears, then press it. 3 Rotate the control dial to select from 50K/9K, 100K/10K or 200K/10K, then press it. Receivable frequency by selected frequency setup: FM 50 khz: MHz, MHz, MHz... FM 100 khz: 87.5 MHz, 87.6 MHz, 87.7 MHz... FM 200 khz: 87.5 MHz, 87.7 MHz, 87.9 MHz... AM 9 khz: 531 khz, 540 khz, 549 khz... AM 10 khz: 530 khz, 540 khz, 550 khz... 2 Rotate the control dial until DEMO appears, then press it. 3 Rotate the control dial to select DEMO-OFF, then press it. The setting is complete. 4 Press (BACK) twice. The display returns to normal reception/ play mode. Setting the clock The clock uses a 12-hour digital indication. 1 Press, rotate the control dial until GENERAL appears, then press it. 2 Rotate the control dial until CLOCK- ADJ appears, then press it. The hour indication flashes. 3 Rotate the control dial to set the hour and minute. To move the digital indication, press /+. 4 After setting the minute, press. The setup is complete and the clock starts. To display the clock, press. Canceling the DEMO mode You can cancel the demonstration display which appears while this unit is turned off. 1 Press, rotate the control dial until DISPLAY appears, then press it. 4

5 Detaching the front panel You can detach the front panel of this unit to prevent theft. 1 Press and hold. The unit is turned off. 2 Press the front panel release button, then remove the panel by pulling it towards you. Caution alarm If you turn the ignition switch to the OFF position without detaching the front panel, the caution alarm will sound for a few seconds. The alarm will only sound if the built-in amplifier is used. Note Do not subject the front panel to heat/high temperature or moisture. Avoid leaving it in a parked car or on a dashboard/rear tray. Attaching the front panel Engage part of the front panel with part of the unit, as illustrated, and push the left side into position until it clicks. 5

6 Location of controls Main unit 6 This section contains instructions on the location of controls and basic operations. SOURCE/OFF button Press to turn on the power; select the source (Radio/CD/USB/AUX). Press repeatedly to change to another source. Press and hold for 1 second to turn off the power. Press and hold for more than 2 seconds to turn off the power and the display disappears. SEEK +/ buttons Radio: To tune in stations automatically (press); find a station manually (press and hold). CD/USB: To skip a track (press); skip tracks continuously (press, then press again within about 2 seconds and hold); reverse/fast-forward a track (press and hold). ZAP button page 12 To enter ZAPPIN mode. Control dial/enter/menu button page 15 Rotate to adjust volume. Press to enter setup mode. Receptor for the remote commander Disc slot Insert the disc (label side up), playback starts. Display window (Eject) button To eject the disc. USB port page 10 (BACK)/MODE button page 8 Press to return to the previous display; select the radio band (FM/AM). Front panel release button page 5 (BROWSE) button page 12 To enter the Quick-BrowZer mode (CD/USB). PTY (Program Type) button page 9 To select PTY in RDS.

7 Number buttons Radio: To receive stored stations (press); store stations (press and hold). CD/USB: / : ALBUM / (during MP3/ WMA/AAC playback) To skip an album (press); skip albums continuously (press and hold). : (Repeat)* page 11 : SHUF page 11 : PAUSE To pause playback. Press again to resume playback. DSPL (Display)/SCRL (Scroll) button page 9, 10, 11 To change display items (press); scroll a display item (press and hold). AUX input jack page 18 * This button has a tactile dot. Note If the unit is turned off and the display disappears, the unit cannot be operated with the remote commander unless on the unit is pressed, or a disc is inserted to activate the unit first. RM-X211 Remote commander Remove the insulation film before use. OFF button To turn off the power; stop the source. SOURCE button Press to turn on the power. Press repeatedly to change to another source (Radio/CD/USB/AUX). ( )/ ( ) buttons To control Radio/CD/USB, the same as /+ on the unit. Setup items, etc., can be operated by. (BACK) button To return to the previous display. ENTER button To apply a setting. PTY (Program Type) button VOL (Volume) +*/ button 7

8 ATT (Attenuate) button To attenuate the sound. To cancel, press again. MODE button Press to select the radio band (FM/AM). SOUND/MENU button To enter the SOUND menu directly (press); to enter setup mode (press and hold). (BROWSE) button (+)/ ( ) buttons To control CD/USB, the same as / on the unit. Setup items, etc., can be operated by. DSPL (Display)/SCRL (Scroll) button Number buttons To receive stored stations (press); store stations (press and hold). To pause playback (press ). * This button has a tactile dot. Radio Storing and receiving stations Tuning step setting is required (page 4). Notes If the tuning step setting is changed, the stored stations will be erased. If replacing the car battery or changing the connections, the tuning step setting will be erased, and you will need to set again. Caution When tuning in stations while driving, use Best Tuning Memory (BTM) to prevent an accident. Storing automatically BTM 1 Press repeatedly until TUNER appears. To change the band, press repeatedly. You can select from FM1, FM2, FM3, AM1 or AM2. 2 Press, rotate the control dial until GENERAL appears, then press it. 3 Rotate the control dial until BTM appears, then press it. The unit stores stations in order of frequency on the number buttons. Storing manually 8 1 While receiving the station that you want to store, press and hold a number button ( to ) until MEM appears.

9 Receiving the stored stations 1 Select the band, then press a number button ( to ). Tuning automatically 1 Select the band, then press +/ to search for the station. Scanning stops when the unit receives a station. Repeat this procedure until the desired station is received. Tip If you know the frequency of the station you want to listen to, press and hold +/ to locate the approximate frequency, then press +/ repeatedly to fine adjust to the desired frequency (manual tuning). RDS FM stations with Radio Data System (RDS) service send inaudible digital information along with the regular radio program signal. Notes Depending on the country/region, not all RDS functions may be available. RDS will not work if the signal strength is too weak, or if the station you are tuned to is not transmitting RDS data. Changing display items Press. Selecting PTY (Program Types) Use PTY to display or search for a desired program type. 2 Rotate the control dial until the desired program type appears, then press it. The unit starts to search for a station broadcasting the selected program type. Type of programs NEWS (News), AFFAIRS (Current Affairs), INFO (Information), SPORT (Sports), EDUCATE (Education), DRAMA (Drama), CULTURE (Culture), SCIENCE (Science), VARIED (Varied), POP M (Pop Music), ROCK M (Rock Music), EASY M (M.O.R. Music), LIGHT M (Light classical), CLASSICS (Serious classical), OTHER M (Other Music), WEATHER (Weather), FINANCE (Finance), CHILDREN (Children s program), SOCIAL A (Social Affairs), RELIGION (Religion), PHONE IN (Phone In), TRAVEL (Travel), LEISURE (Leisure), JAZZ (Jazz Music), COUNTRY (Country Music), NATION M (National Music), OLDIES (Oldies Music), FOLK M (Folk Music), DOCUMENT (Documentary) Note You may receive a different radio program from the one you select. Setting CT (Clock Time) The CT data from the RDS transmission sets the clock. 1 Set CT-ON in setup (page 16). Note The CT function may not work properly even though an RDS station is being received. 1 Press during FM reception. The current program type name appears if the station is transmitting PTY data. 9

10 CD Playing a disc This unit can play CD-DA (also containing CD TEXT) and CD-R/CD-RW (MP3/ WMA/AAC files (page 19)). 1 Insert the disc (label side up). Playback starts automatically. To eject the disc, press. Notes When ejecting/inserting a disc, keep any USB devices disconnected to avoid damage to the disc. Corresponding codec is MP3 (.mp3), WMA (.wma), and AAC (.m4a). Changing display items Press. Displayed items may differ depending on the disc type, recording format and settings. USB devices MSC (Mass Storage Class)-type USB devices compliant with the USB standard can be used. Backup of data to a USB device is recommended. MSC (Mass Storage Class)-type Android Phone compliant with the USB standard can be used. Depending on the Android Phone, setting the USB connection mode to MSC is required. Notes Connect the USB device after starting the engine. Depending on the USB device, malfunction or damage may occur if it is connected before starting the engine. Corresponding codec is MP3 (.mp3), WMA (.wma), AAC (.m4a) and AAC (.mp4). For details on the compatibility of your USB device, visit the support site on the back cover. Playing back a USB device 1 Open the USB cover, then connect the USB device to the USB port. 10 Playback starts. If a USB device is already connected, to start playback, press repeatedly until USB appears. To stop playback, press and hold for 1 second.

11 To remove the USB device, stop the USB playback, then remove the USB device. Notes Do not use USB devices so large or heavy that they may fall down due to vibration, or cause a loose connection. Do not detach the front panel during playback of the USB device, otherwise USB data may be damaged. Changing display items Press. Displayed items may differ depending on the USB device, recording format and settings. Notes The maximum number of tracks is 10,000. It may take time for playback to begin, depending on the amount of recorded data. During playback or fast-forward/reverse of a VBR (Variable Bit Rate) MP3/WMA/AAC file, elapsed playing time may not display accurately. Playback of the following MP3/WMA/AAC files is not supported. lossless compression copyright-protected DRM (Digital Rights Management) files Multi-channel audio files Searching and playing tracks Playing tracks in various modes You can listen to tracks repeatedly (repeat play) or in random order (shuffle play). Available play modes differ depending on the selected sound source. 1 During playback, press ( ) or (SHUF) repeatedly until the desired play mode appears. Playback in selected play mode may take time to start. Repeat play Select TRACK ALBUM OFF Shuffle play To play track repeatedly. album repeatedly. track in normal order (Normal play). Select SHUF ALBUM SHUF DISC* 1 SHUF DEVICE* 2 SHUF OFF To play album in random order. disc in random order. device in random order. track in normal order (Normal play). *1 CD only *2 USB only 11

12 Searching a track by name Quick-BrowZer You can search for a track in a CD or USB device easily by category. 1 Press (BROWSE)*. The unit enters the Quick-BrowZer mode, and the list of search categories appears. When the track list appears, press (BACK) repeatedly until the desired search category appears. * During USB playback, press (BROWSE) for more than 2 seconds to directly return to the beginning of the category list. 2 Rotate the control dial to select the desired search category, then press it to confirm. 3 Repeat step 2 until the desired track is selected. Playback starts. To exit the Quick-BrowZer mode, press (BROWSE). Note When entering the Quick-BrowZer mode, the repeat/shuffle setting is canceled. Searching by skip items Jump mode When many items are in a category, you can search for a desired item quickly. 1 Press + in Quick-BrowZer mode. The item name will appear. 2 Rotate the control dial to select the item near the one desired. The list is skipped in steps of 10% of the total number of items in the list. 3 Press. The display returns to the Quick- BrowZer mode and the selected item appears. 4 Rotate the control dial to select the desired item and press it. Playback starts if the selected item is a track. To cancel Jump mode, press (BACK) or. Searching a track by listening to track passages ZAPPIN By playing back short track passages in a CD or USB device in sequence, you can search for a track you want to listen to. ZAPPIN mode is suitable for searching for a track in shuffle or shuffle repeat mode. 1 Press during playback. Playback starts from a passage of the next track. You can select the playback time (page 16). Track pressed. The part of each track to play back in ZAPPIN mode. 2 Press or when a track you want to listen is played back. The track that you select returns to normal play mode from the beginning. Pressing (BACK) will also play back the chosen track. Tips Press +/ in ZAPPIN mode to skip a track. Press / (ALBUM / ) in ZAPPIN mode to skip an album. 12

13 Sound Settings and Setup Menu Enjoying sophisticated sound functions Advanced Sound Engine Advanced Sound Engine creates an ideal incar sound field with digital signal processing. Selecting the sound quality EQ7 Preset You can select an equalizer curve from 7 equalizer curves (XPLOD, VOCAL, EDGE, CRUISE, SPACE, GRAVITY, CUSTOM or OFF). 1 During reception/playback, press, rotate the control dial until SOUND appears, then press it. 2 Rotate the control dial until EQ7 PRESET appears, then press it. 3 Rotate the control dial until the desired equalizer curve appears, then press it. 4 Press (BACK) twice. To cancel the equalizer curve, select OFF in step 3. Tip The equalizer curve setting can be memorized for each source. 1 After selecting a source, press, rotate the control dial until SOUND appears, then press it. 2 Rotate the control dial until EQ7 SETTING appears, then press it. 3 Rotate the control dial until BASE appears, then press it. You can select an equalizer curve as a basis for further customizing. 4 Rotate the control dial to select the equalizer curve, then press it. 5 Setting the equalizer curve. Rotate the control dial to select the frequency range, then press it. BAND1: 63 Hz BAND2: 160 Hz BAND3: 400 Hz BAND4: 1 khz BAND5: 2.5 khz BAND6: 6.3 khz BAND7: 16.0 khz Rotate the control dial to adjust the volume level, then press it. The volume level is adjustable in 1 db steps, from -6 db to +6 db. Repeat steps and to adjust other frequency ranges. 6 Press (BACK) to return to the previous display. The equalizer curve is stored in CUSTOM. Customizing the equalizer curve EQ7 Setting CUSTOM of EQ7 allows you to make your own equalizer settings. Optimizing sound by Time Alignment Listening Position The unit can simulate a natural sound field by delaying the sound output from each speaker to suit your position. 13

14 The options for POSITION are indicated below. FRONT L ( ): Front left FRONT R ( ): Front right FRONT ( ): Center front ALL ( ): In the center of your car OFF: No position set To cancel listening position, select OFF in step 4. Adjusting the listening position You can fine-tune the listening position setting. 14 You can also set the approximate subwoofer position from your listening position if: the audio output is set to SUB-OUT (page 16). the listening position is set to other than OFF. The options for SET SW POS are indicated below. NEAR ( ): Near NORMAL ( ): Normal FAR ( ): Far 1 During reception/playback, press, rotate the control dial until SOUND appears, then press it. 2 Rotate the control dial until POSITION appears, then press it. 3 Rotate the control dial until SET F/R POS appears, then press it. 4 Rotate the control dial to select from FRONT L, FRONT R, FRONT or ALL, then press it. 5 Rotate the control dial until SET SW POS appears, then press it. 6 Rotate the control dial to select the subwoofer position from NEAR, NORMAL or FAR, then press it. 7 Press (BACK) to return to the previous display. 1 During reception/playback, press, rotate the control dial until SOUND appears, then press it. 2 Rotate the control dial until POSITION appears, then press it. 3 Rotate the control dial until ADJ POSITION appears, then press it. 4 Rotate the control dial to adjust the listening position, then press it. Adjustable range: +3 CENTER 3. 5 Press (BACK) to return to the previous display. DM+ Advanced DM+ Advanced improves digitally compressed sound by restoring high frequencies lost in the compression process. 1 During playback, press, rotate the control dial until SOUND appears, then press it. 2 Rotate the control dial until DM+ appears, then press it. 3 Rotate the control dial to select ON, then press it. 4 Press (BACK) twice. Tip The DM+ setting can be memorized for each source other than the tuner.

15 Using rear speakers as subwoofer Rear Bass Enhancer Rear Bass Enhancer enhances the bass sound by applying a low pass filter setting (page 16) to the rear speakers. This function allows the rear speakers to work as a subwoofer if one is not connected. 1 During reception/playback, press, rotate the control dial until SOUND appears, then press it. 2 Rotate the control dial until RB ENH appears, then press it. 3 Rotate the control dial until RBE MODE appears, then press it. 4 Rotate the control dial to select from 1, 2 or 3, then press it. 5 Press (BACK) to return to the previous display. Using a subwoofer without a power amplifier Subwoofer Direct Connection You can use the subwoofer without a power amplifier when it is connected to the rear speaker cord. Note Be sure to connect a 4-8 ohm subwoofer to either of the rear speaker cords. Do not connect a speaker to the other rear speaker cord. 1 During reception/playback, press, rotate the control dial until SOUND appears, then press it. 2 Rotate the control dial until SW DIREC appears, then press it. 3 Rotate the control dial until SW MODE appears, then press it. 4 Rotate the control dial to select 1, 2 or 3, then press it. 5 Press (BACK) to return to the previous display. For details on the settings for the subwoofer phase, position, low pass filter frequency and the low pass filter slope, see page 16. Adjusting setup items 1 Press, rotate the control dial until the desired category appears, then press it. 2 Rotate the control dial until the desired item appears, then press it. 3 Rotate the control dial to select the setting, then press it.* The setting is complete. 4 Press (BACK) to return to the previous display. *For CLOCK-ADJ, TUNER-STP and BTM settings, step 4 is not necessary. The following items can be set depending on the source and setting: GENERAL: CLOCK-ADJ (Clock Adjust) (page 4) TUNER-STP* 1 (Tuner Step) (page 4) CAUT ALM* 1 (Caution Alarm) Activates the caution alarm: ON, OFF (page 5). BEEP Activates the beep sound: ON, OFF. AUTO OFF Shuts off automatically after a desired time when the unit is turned off: NO, 30S (Seconds), 30M (Minutes), 60M (Minutes). 15

16 AUX-A* 1 (AUX Audio) Activates the AUX source display: ON, OFF (page 18). REAR/SUB* 1 Switches the audio output: SUB-OUT (subwoofer), REAR-OUT (power amplifier). CT (Clock Time) Activates the CT function: ON, OFF (page 9). BTM* 2 (page 8) ZAPPIN* 3 ZAP TIME (Zappin Time) Selects the playback time for the ZAPPIN function. Z.TIME-1 (about 6 seconds), Z.TIME-2 (about 15 seconds), Z.TIME-3 (about 30 seconds). ZAP BEEP (Zappin Beep) Applies a beep sound between track passages: ON, OFF. *1 When the unit is turned off. *2 When the tuner is selected. *3 When the CD or USB is selected. SOUND: EQ7 PRESET (page 13) EQ7 SETTING (page 13) POSITION SET F/R POS (Set Front/Rear Position) (page 13) ADJ POSITION* 1 (Adjust Position) (page 14) SET SW POS* 1 * 2 (Set Subwoofer Position) (page 14) DM+* 3 (page 14) LOUDNESS (Dynamic Loudness) Reinforces bass and treble for clear sound at low volume levels: ON, OFF. ALO (Automatic Level Optimizer) Adjust the playback volume level of all playback sources to the optimum level: ON, OFF. RB ENH* 4 (Rear Bass Enhancer) RBE MODE (Rear Bass Enhancer Mode) Selects the rear bass enhancer mode: 1, 2, 3, OFF. LPF FREQ (Low Pass Filter Frequency) Selects the subwoofer cut-off frequency: 50Hz, 60Hz, 80Hz, 100Hz, 120Hz. LPF SLOP (Low Pass Filter Slope) Selects the LPF slope: 1, 2, 3. SW DIREC* 5 (Subwoofer Direct Connection) SW MODE (Subwoofer Mode) Selects the subwoofer mode: 1, 2, 3, OFF. SW PHASE (Subwoofer Phase) Selects the subwoofer phase: NORM, REV. SW POS* 1 (Subwoofer Position) (page 14) Selects the subwoofer position: NEAR, NORMAL, FAR. LPF FREQ (Low Pass Filter Frequency) Selects the subwoofer cut-off frequency: 50Hz, 60Hz, 80Hz, 100Hz, 120Hz. LPF SLOP (Low Pass Filter Slope) Selects the LPF slope: 1, 2, 3. BALANCE Adjusts the sound balance: RIGHT-15 CENTER LEFT FADER Adjusts the relative level: FRONT-15 CENTER REAR-15.

17 S.WOOFER* 2 (Subwoofer) SW LEVEL (Subwoofer Level) Adjusts the subwoofer volume level: +10 db 0 db 10 db. ( ATT is displayed at the lowest setting.) SW PHASE (Subwoofer Phase) Selects the subwoofer phase: NORM, REV. SW POS* 1 (Subwoofer Position) Selects the subwoofer position: NEAR, NORMAL, FAR. LPF FREQ (Low Pass Filter Frequency) Selects the subwoofer cut-off frequency: 50Hz, 60Hz, 80Hz, 100Hz, 120Hz. LPF SLOP (Low Pass Filter Slope) Selects the LPF slope: 1, 2, 3. HPF (High Pass Filter) HPF FREQ (High Pass Filter Frequency) Selects the front/rear speaker cut-off frequency: OFF, 50Hz, 60Hz, 80Hz, 100Hz, 120Hz. HPF SLOP (High Pass Filter Slope) Selects the HPF slope (effective only when HPF FREQ is set to other than OFF ): 1, 2, 3. DISPLAY: DEMO (Demonstration) Activates the demonstration: ON, OFF. BLK OUT (Black Out) Turns off the illumination automatically for any source (e.g., during radio reception/cd playback, etc.) if no operation is performed for 5 seconds: ON, OFF. To turn the light back on, press any button on the unit or the remote commander. DIMMER Changes the display brightness: ON, OFF. AUTO SCR* (Auto Scroll) Scrolls long items automatically: ON, OFF. M.DISPLAY (Motion Display) SA : to show moving patterns and spectrum analyzer. OFF : to deactivate the Motion Display. * When the CD or USB is selected. AUX VOL* 6 (AUX Volume level) Adjusts the volume level for each connected auxiliary equipment: +18 db 0 db 8 db. This setting negates the need to adjust the volume level between sources. *1 Does not appear when SET F/R POS is set to OFF. *2 When the audio output is set to SUB-OUT (page 16). *3 Does not appear when the tuner is selected. *4 When the audio output is set to REAR- OUT and SW DIREC is set to OFF. *5 When the audio output is set to REAR- OUT and RBE MODE is set to OFF. *6 When the AUX is selected. 17

18 Using optional equipment Auxiliary audio equipment By connecting an optional portable audio device to the AUX input jack (stereo mini jack) on the unit and then simply selecting the source, you can listen on your car speakers. Connecting the portable audio device 1 Turn off the portable audio device. 2 Turn down the volume on the unit. 3 Connect the portable audio device to the unit with a connecting cord (not supplied)*. * Be sure to use a straight type plug. Additional Information Precautions Cool off the unit beforehand if your car has been parked in direct sunlight. Do not leave the front panel or audio devices brought in inside the car, or it may cause malfunction due to high temperature in direct sunlight. Power antenna (aerial) extends automatically. Moisture condensation Should moisture condensation occur inside the unit, remove the disc and wait for about an hour for it to dry out; otherwise the unit will not operate properly. To maintain high sound quality Do not splash liquid onto the unit or discs. 18 Adjusting the volume level Be sure to adjust the volume for each connected audio device before playback. 1 Turn down the volume on the unit. 2 Press repeatedly until AUX appears. 3 Start playback of the portable audio device at a moderate volume. 4 Set your usual listening volume on the unit. 5 Adjust the input level (page 17). Notes on discs Do not expose discs to direct sunlight or heat sources such as hot air ducts, nor leave it in a car parked in direct sunlight. Before playing, wipe the discs with a cleaning cloth from the center out. Do not use solvents such as benzine, thinner, commercially available cleaners. This unit is designed to play back discs that conform to the Compact Disc (CD) standard. DualDiscs and some of the music discs encoded with copyright protection technologies do not conform to the Compact Disc (CD) standard, therefore, these discs may not be playable by this unit.

19 Discs that this unit CANNOT play Discs with labels, stickers, or sticky tape or paper attached. Doing so may cause a malfunction, or may ruin the disc. Discs with non-standard shapes (e.g., heart, square, star). Attempting to do so may damage the unit. 8 cm (3 1 /4 in) discs. Notes on CD-R/CD-RW discs The maximum number of: (CD-R/CD-RW only) folders (albums): 150 (including root folder) files (tracks) and folders: 300 (may less than 300 if folder/file names contain many characters) displayable characters for a folder/file name: 32 (Joliet)/64 (Romeo) If the multi-session disc begins with a CD- DA session, it is recognized as a CD-DA disc, and other sessions are not played back. Discs that this unit CANNOT play CD-R/CD-RW of poor recording quality. CD-R/CD-RW recorded with an incompatible recording device. CD-R/CD-RW which is finalized incorrectly. CD-R/CD-RW other than those recorded in music CD format or MP3 format conforming to ISO9660 Level 1/Level 2, Joliet/Romeo or multi-session. Playback order of MP3/WMA/ AAC files MP3/WMA/AAC Folder (album) MP3/WMA/ AAC file (track) Maintenance Replacing the lithium battery of the remote commander When the battery becomes weak, the range of the remote commander becomes shorter. Replace the battery with a new CR2025 lithium battery. Use of any other battery may present a risk of fire or explosion. + side up Notes on the lithium battery Keep the lithium battery out of the reach of children. Should the battery be swallowed, immediately consult a doctor. Wipe the battery with a dry cloth to assure a good contact. Be sure to observe the correct polarity when installing the battery. Do not hold the battery with metallic tweezers, otherwise a short-circuit may occur. WARNING Battery may explode if mistreated. Do not recharge, disassemble, or dispose of in fire. Cleaning the connectors The unit may not function properly if the connectors between the unit and the front panel are not clean. In order to prevent this, detach the front panel (page 5) and clean the connectors with a cotton swab. Do not apply too much force. Otherwise, the connectors may be damaged. If you have any questions or problems concerning your unit that are not covered in this manual, consult your nearest Sony dealer. 19

20 20 Notes For safety, turn off the ignition before cleaning the connectors, and remove the key from the ignition switch. Never touch the connectors directly with your fingers or with any metal device. Specifications Tuner section FM Tuning range: MHz (at 50 khz step) MHz (at 100 khz step) MHz (at 200 khz step) FM tuning step: 50 khz/100 khz/200 khz switchable Antenna (aerial) terminal: External antenna (aerial) connector Intermediate frequency: 25 khz Usable sensitivity: 8 dbf Selectivity: 75 db at 400 khz Signal-to-noise ratio: 80 db (stereo) Separation: 50 db at 1 khz Frequency response: 20 15,000 Hz AM Tuning range: 531 1,602 khz (at 9 khz step) 530 1,710 khz (at 10 khz step) AM tuning step: 9 khz/10 khz switchable Antenna (aerial) terminal: External antenna (aerial) connector Intermediate frequency: 9,124.5 khz or 9,115.5 khz/4.5 khz (at 9 khz step) 9,115 khz or 9,125 khz/5 khz (at 10 khz step) Sensitivity: 26 μv CD Player section Signal-to-noise ratio: 120 db Frequency response: 10 20,000 Hz Wow and flutter: Below measurable limit USB Player section Interface: USB (Full-speed) Maximum current: 1 A Power amplifier section Output: Speaker outputs Speaker impedance: 4 8 ohms Maximum power output: 52 W 4 (at 4 ohms) General Outputs: CDX-GT522U: Audio outputs terminal (front, rear/sub switchable) CDX-GT520U: Audio outputs terminal (rear/sub switchable) Power antenna (aerial)/power amplifier control terminal (REM OUT) Inputs: Remote controller input terminal Antenna (aerial) input terminal AUX input jack (stereo mini jack) USB port Power requirements: 12 V DC car battery (negative ground (earth)) Dimensions: Approx mm (7 1 /8 2 7 in) (w/h/d) Mounting dimensions: Approx mm (7 1 /4 2 1 /8 6 5 /16 in) (w/h/d) Mass: Approx. 1.2 kg (2 lb 11 oz) Supplied accessories: Remote commander: RM-X211 Parts for installation and connections (1 set) Your dealer may not handle some of the above listed accessories. Please ask the dealer for detailed information. Design and specifications are subject to change without notice. Troubleshooting The following checklist will help you remedy problems you may encounter with your unit. Before going through the checklist below, check the connection and operating procedures. For details on using the fuse and removing the unit from the dashboard, refer to the installation/connections manual supplied with this unit. If the problem is not solved, visit the support site on the back cover. General No power is being supplied to the unit. Check the connection or fuse.

21 If the unit is turned off and the display disappears, the unit cannot be operated with the remote commander. Turn on the unit. The power antenna (aerial) does not extend. The power antenna (aerial) does not have a relay box. No sound. The ATT function is activated. The position of the fader control FADER is not set for a 2-speaker system. No beep sound. The beep sound is canceled (page 15). An optional power amplifier is connected and you are not using the built-in amplifier. The contents of the memory have been erased. The power supply lead or battery has been disconnected or not connected properly. The unit is reset. Store again into the memory. Stored stations and correct time are erased. The fuse has blown. Makes noise when the position of the ignition is switched. The leads are not matched correctly with the car s accessory power connector. During playback or reception, demonstration mode starts. If no operation is performed for 5 minutes with DEMO-ON set, demonstration mode starts. Set DEMO-OFF (page 17). The display disappears from/does not appear in the display window. The dimmer is set to DIM-ON (page 17). The display disappears if you press and hold. Press on the unit until the display appears. The connectors are dirty (page 19). The Auto Off function does not operate. The unit is turned on. The Auto Off function activates after turning off the unit. Turn off the unit. The display disappears while the unit is operating. The Black Out function is set to on (page 17). The operation buttons do not function. The disc will not eject. Press and (BACK)/ for more than 2 seconds. The contents stored on the memory are erased. For your safety, do not perform the reset operation while you are driving Radio reception The stations cannot be received. The sound is hampered by noises. The connection is not correct. Connect an REM OUT lead (blue/white striped) or accessory power supply lead (red) to the power supply lead of a car s antenna (aerial) booster (only when your car has built-in radio antenna (aerial) in the rear/ side glass). Check the connection of the car antenna (aerial). If the auto antenna (aerial) will not go up, check the connection of the power antenna (aerial) control lead. The tuning step setting has been erased. Set the tuning step again (page 4). Preset tuning is not possible. Store the correct frequency in the memory. The broadcast signal is too weak. Automatic tuning is not possible. The broadcast signal is too weak. Perform manual tuning. RDS PTY displays The current station is not an RDS station. RDS data has not been received. The station does not specify the program type. CD playback The disc cannot be loaded. Another disc is already loaded. 21

22 22 The disc has been forcibly inserted upside down or in the wrong way. The disc does not play back. Defective or dirty disc. The CD-Rs/CD-RWs are not for audio use (page 19). MP3/WMA/AAC files cannot be played back. The disc is incompatible with the MP3/WMA/ AAC format and version. For details on playable discs and formats, visit the support site. MP3/WMA/AAC files take longer to play back than others. The following discs take a longer time to start playback. a disc recorded with a complicated tree structure. a disc recorded in Multi Session. a disc to which data can be added. The display items do not scroll. For discs with very many characters, those may not scroll. AUTO SCR is set to OFF. Set A.SCRL-ON (page 17). Press and hold (SCRL). The sound skips. Installation is not correct. Install the unit at an angle of less than 45 in a sturdy part of the car. Defective or dirty disc. USB playback You cannot play back items via a USB hub. This unit cannot recognize USB devices via a USB hub. Cannot play back items. A USB device does not work. Connect it again. A USB device takes longer to play back. The USB device contains files with a complicated tree structure. The sound is intermittent. The sound may be intermittent at a high-bitrate of more than 320 kbps. Error displays/messages CHECKING The unit is confirming the connection of a USB device. Wait until confirming the connection is finished. ERROR The disc is dirty or inserted upside down. Clean or insert the disc correctly. A blank disc has been inserted. The disc cannot play due to a problem. Insert another disc. USB device was not automatically recognized. Connect it again. Press to remove the disc. FAILURE The connection of speakers/amplifiers is incorrect. See the installation/connections manual of this model to check the connection. HUB NO SUPRT (Hubs Not Supported) USB hub is not supported on this unit. NO DEV (No Device) USB is selected as source without a USB device connected. A USB device or a USB cable has been disconnected during playback. Be sure to connect a USB device and USB cable. NO MUSIC The disc or USB device does not contain a music file. Insert a music CD in this unit. Connect a USB device with a music file in it. NO NAME A disc/album/artist/track name is not written in the track. OFFSET There may be an internal malfunction. Check the connection. If the error indication remains on in the display, consult your nearest Sony dealer.

23 OVERLOAD USB device is overloaded. Disconnect the USB device, then change the source by pressing. Indicates that the USB device is out of order, or an unsupported device is connected. PUSH EJT (Push Eject) The disc cannot be ejected. Press (eject). READ The unit is reading all track and album information on the disc. Wait until reading is complete and playback starts automatically. Depending on the disc structure, it may take more than a minute. USB NO SUPRT (USB Not Supported) The connected USB device is not supported. For details on the compatibility of your USB device, visit the support site. or During reverse or fast-forward, you have reached the beginning or the end of the disc and you cannot go any further. The character cannot be displayed with the unit. If these solutions do not help improve the situation, consult your nearest Sony dealer. If you take the unit to be repaired because of CD playback trouble, bring the disc that was used at the time the problem began. 23

24 자동차시동키에 ACC 위치가없을경우의경고자동꺼짐기능을설정하십시오 (15 페이지 ). 기기가꺼지고설정된시간이지나면자동으로완전히종료되므로배터리소모가방지됩니다. 자동꺼짐기능을설정하지않은경우시동키를끌때마다디스플레이가사라질때까지 를누르고계십시오. 레이저다이오드속성 방사지속시간 : 연속 레이저출력 : 53.3μW 미만 ( 이출력은 Optical Pick-up Block 의대물렌즈표면에서 7 mm 조리개를사용하여 200 mm 의거리에서측정한값입니다.) Android 는 Google Inc. 의상표입니다. 이상표의사용은 Google Permissions 의적용을받습니다. 2

25 목차 시작하기 FM/AM 튜닝단위전환하기 DEMO 모드취소하기 시계설정하기 전면패널분리하기 컨트롤위치 본체 RM-X211 리모컨 라디오 방송국저장및수신하기 RDS CD 디스크재생하기 USB 장치 USB 장치재생하기 트랙검색및재생하기 다양한모드로트랙재생하기 이름으로트랙검색하기 Quick-BrowZer 트랙구절을청취하여트랙검색하기 ZAPPIN 사운드설정및설정메뉴 정교한사운드기능즐기기 고급사운드엔진 설정항목조정하기 옵션장비사용하기 보조오디오장비 추가정보 사용전주의사항 유지관리 주요제원 문제해결

26 시작하기 FM/AM 튜닝단위전환하기 FM/AM 튜닝단위는출하시 50 khz (FM)/9 khz(am) 로설정되어있습니다. 해당국가의주파수할당방식이 200 khz (FM)/10 khz(am) 또는 100 khz(fm)/ 10 khz(am) 단위에기반을두는경우사용전에튜닝단위를설정하십시오. 이설정은기기의전원이꺼진경우표시됩니다. 1 를누르고, "GENERAL" 이나타날때까지컨트롤다이얼을돌린다음누릅니다. 2 "TUNER-STP" 가나타날때까지컨트롤다이얼을돌린다음누릅니다. 3 컨트롤다이얼을돌려 "50K/9K", "100K/10K" 또는 "200K/10K" 를선택한다음누릅니다. 선택한주파수설정별수신가능주파수 : FM 50 khz: MHz, MHz, MHz... FM 100 khz: 87.5 MHz, 87.6 MHz, 87.7 MHz... FM 200 khz: 87.5 MHz, 87.7 MHz, 87.9 MHz... AM 9 khz: 531 khz, 540 khz, 549 khz... AM 10 khz: 530 khz, 540 khz, 550 khz... 3 컨트롤다이얼을돌려 "DEMO-OFF" 를선택한다음누릅니다. 설정이완료되었습니다. 4 (BACK) 을두번누릅니다. 디스플레이가일반수신 / 재생모드로돌아갑니다. 시계설정하기 시계에는 12시간디지털표기가사용됩니다. 1 를누르고, "GENERAL" 이나타날때까지컨트롤다이얼을돌린다음누릅니다. 2 "CLOCK-ADJ" 가나타날때까지컨트롤다이얼을돌린다음누릅니다. 시간표시가깜박입니다. 3 컨트롤다이얼을돌려시간과분을설정합니다. 디지털표시를이동하려면 -/+ 를누릅니다. 4 분을설정한후 를누릅니다. 설정이완료되었으며시계가시작됩니다. 시계를표시하려면 을누릅니다. DEMO 모드취소하기 기기의전원이꺼질때표시되는데모를취소할수있습니다. 1 를누르고 "DISPLAY" 가나타날때까지컨트롤다이얼을돌린다음누릅니다. 2 "DEMO" 가나타날때까지컨트롤다이얼을돌린다음누릅니다. 4

27 전면패널분리하기 도난방지를위해본기기의전면패널을분리할수있습니다. 1 을길게누릅니다. 기기가꺼집니다. 2 전면패널해제버튼 를누른다음앞으로당겨패널을제거합니다. 경고성알람전면패널을분리하지않고시동키를 OFF 쪽에놓을경우경고성알람이몇초간울립니다. 알람은내장앰프가사용된경우에만울립니다. 참고 전면패널을고온다습한곳에두지마십시오. 주차한차량에그대로두거나계기판이나뒷좌석트렁크위에놓지마십시오. 전면패널부착하기 그림과같이전면패널의 부위를기기의 부위에결합하여찰칵소리가날때까지왼쪽을누릅니다. 5

28 컨트롤위치 본체 6 이단원에서는컨트롤위치와기본조작에대한지침이제공됩니다. SOURCE/OFF 버튼전원을켜거나소스 ( 라디오 /CD/USB/ AUX) 를선택합니다. 다른소스로변경하려면반복해서누릅니다. 전원을끄려면 1초간길게누릅니다. 전원을끄고디스플레이를사라지게하려면 2초이상길게누릅니다. SEEK +/- 버튼라디오 : 방송국을자동튜닝하거나 ( 누르기 ), 방송국을수동으로찾습니다 ( 길게누르기 ). CD/USB: 트랙을건너뛰거나 ( 누르기 ), 트랙을연속건너뛰거나 ( 누른다음약 2초내에다시길게누르기 ), 트랙되감기 / 빨리감기를합니다 ( 길게누르기 ). ZAP 버튼 12페이지 ZAPPIN 모드로들어갑니다. 컨트롤다이얼 /ENTER/MENU 버튼 15페이지볼륨을조정하려면돌립니다. 설정모드로들어가려면누릅니다. 리모컨수신부 디스크슬롯디스크를넣으면 ( 라벨면이윗면 ) 재생이시작됩니다. 디스플레이창 ( 꺼내기 ) 버튼디스크를꺼냅니다. USB 포트 10페이지 (BACK)/MODE 버튼 8페이지이전디스플레이로돌아가거나라디오대역 (FM/AM) 을선택하려면누릅니다. 전면패널해제버튼 5페이지 (BROWSE) 버튼 12 페이지 Quick-BrowZer 모드로들어갑니다 (CD/USB). PTY( 프로그램유형 ) 버튼 9 페이지 RDS 에서 PTY 를선택합니다.

29 숫자버튼라디오 : 저장된방송국을수신하거나 ( 누르기 ), 방송국을저장합니다 ( 길게누르기 ). CD/USB: / : ALBUM / (MP3/ WMA/AAC 재생도중 ) 앨범을건너뛰거나 ( 누르기 ), 앨범을연속으로건너뜁니다 ( 길게누르기 ). : ( 반복 )* 11페이지 : SHUF 11페이지 : PAUSE 재생을일시정지합니다. 재생을다시시작하려면다시누릅니다. DSPL( 디스플레이 )/SCRL( 스크롤 ) 버튼 9, 10, 11페이지디스플레이항목을변경하거나 ( 누르기 ), 디스플레이항목을스크롤합니다 ( 길게누르기 ). AUX 입력잭 18페이지 * 이버튼에는돌기가있습니다. RM-X211 리모컨 사용전에절연필름을제거하십시오. 참고 기기가꺼지고디스플레이가사라진경우기기에서 를누르거나디스크를넣어기기를활성화한후에만리모컨으로조작할수있습니다. OFF 버튼전원을끄거나, 소스를중지합니다. SOURCE 버튼전원을켜려면누릅니다. 다른소스 ( 라디오 /CD/USB/AUX) 로변경하려면반복해서누릅니다. ( )/ ( ) 버튼라디오 /CD/USB를제어합니다. 기기의 -/+ 와동일합니다. 설정항목등은 를사용하여조작할수있습니다. (BACK) 버튼이전화면으로돌아갑니다. ENTER 버튼설정을적용합니다. PTY( 프로그램유형 ) 버튼 VOL( 볼륨 ) +*/- 버튼 7

30 ATT( 약화 ) 버튼사운드를약화시킵니다. 취소하려면다시누릅니다. MODE 버튼라디오대역 (FM/AM) 을선택하려면누릅니다. SOUND/MENU 버튼 SOUND 메뉴로바로들어가거나 ( 누르기 ) 설정모드로들어갑니다 ( 길게누르기 ). (BROWSE) 버튼 (+)/ (-) 버튼 CD/USB를제어합니다. 기기의 / 와동일합니다. 설정항목등은 를사용하여조작할수있습니다. DSPL( 디스플레이 )/SCRL( 스크롤 ) 버튼 숫자버튼저장된방송국을수신하거나 ( 누르기 ), 방송국을저장합니다 ( 길게누르기 ). 재생을일시정지합니다 ( 누르기 ). * 이버튼에는돌기가있습니다. 라디오 방송국저장및수신하기 튜닝단위를설정해야합니다 (4 페이지 ). 참고 튜닝단위설정이변경된경우저장된방송국이지워집니다. 자동차배터리를교체하거나연결을변경한경우튜닝단위설정이지워지므로다시설정해야합니다. 주의운전중에방송국을튜닝할때는사고를방지하기위해 BTM(Best Tuning Memory) 을사용하십시오. 자동으로저장하기 BTM 1 "TUNER" 가나타날때까지 를반복해서누릅니다. 대역을변경하려면 를반복해서누릅니다. FM1, FM2, FM3, AM1 또는 AM2 를선택할수있습니다. 2 를누르고, "GENERAL" 이나타날때까지컨트롤다이얼을돌린다음누릅니다. 3 "BTM" 이나타날때까지컨트롤다이얼을돌린다음누릅니다. 숫자버튼의주파수순서대로방송국이저장됩니다. 수동으로저장하기 1 저장할방송국이수신되는상태에서 "MEM" 이나타날때까지숫자버튼 ( - ) 을길게누릅니다. 8

31 저장된방송국수신하기 1 대역을선택하고숫자버튼 ( - ) 을누릅니다. 자동으로튜닝하기 1 대역을선택한다음 +/- 를눌러방송국을검색합니다. 방송국이수신되면스캔이중지됩니다. 원하는방송국이수신될때까지이절차를반복합니다. 팁 청취할방송국의주파수를알고있는경우 +/- 를길게눌러원하는주파수에가까워지면 +/- 를반복해서눌러해당주파수로미세조정합니다 ( 수동튜닝 ). RDS RDS(Radio Data System) 서비스가있는 FM 방송국은귀에들리지않는디지털정보를일반라디오프로그램신호와함께전송합니다. 참고 국가 / 지역에따라일부 RDS 기능을사용하지못할수있습니다. 신호강도가너무약하거나튜닝한방송국에서 RDS 데이터를전송하지않는경우 RDS 가작동되지않습니다. 디스플레이항목변경하기 을누릅니다. PTY( 프로그램유형 ) 선택하기 PTY를사용하여원하는프로그램유형을표시하거나검색합니다. 1 FM 수신중에 를누릅니다. 방송국에서 PTY 데이터를전송하는중이면현재프로그램유형이름이나타납니다. 2 원하는프로그램유형이나타날때까지컨트롤다이얼을돌린다음누릅니다. 선택된프로그램유형을방송하는방송국이검색되기시작합니다. 프로그램유형 NEWS( 뉴스 ), AFFAIRS( 시사 ), INFO ( 정보 ), SPORT( 스포츠 ), EDUCATE ( 교육 ), DRAMA( 드라마 ), CULTURE ( 문화 ), SCIENCE( 과학 ), VARIED ( 기타 ), POP M( 팝음악 ), ROCK M ( 락음악 ), EASY M(M.O.R. 음악 ), LIGHT M( 가벼운클래식 ), CLASSICS ( 정통클래식 ), OTHER M( 기타음악 ), WEATHER( 날씨 ), FINANCE( 금융 ), CHILDREN( 어린이프로그램 ), SOCIAL A( 사회문제 ), RELIGION ( 종교 ), PHONE IN( 전화참가 ), TRAVEL( 여행 ), LEISURE( 레저 ), JAZZ( 재즈음악 ), COUNTRY( 컨츄리음악 ), NATION M( 민속음악 ), OLDIES( 흘러간노래 ), FOLK M( 포크음악 ), DOCUMENT( 다큐멘터리 ) 참고 선택한것과다른라디오프로그램이수신될수있습니다. CT( 시계시간 ) 설정하기 RDS 전송에포함된 CT 데이터는시계를설정합니다. 1 설정에서 "CT-ON" 을설정합니다 (16페이지). 참고 RDS 방송국을수신중인경우에도 CT 기능이제대로작동하지않을수있습니다. 9

32 CD 디스크재생하기 본기기에서는 CD-DA(CD TEXT도포함 ) 및 CD-R/CD-RW(MP3/WMA/ AAC 파일 (19페이지)) 을재생할수있습니다. 1 디스크를넣습니다 ( 라벨면이윗면 ). 자동으로재생이시작됩니다. 디스크를꺼내려면 을누릅니다. 참고 디스크를꺼내거나넣을때디스크가손상되지않도록모든 USB 장치를분리하십시오. 해당코덱은 MP3(.mp3), WMA(.wma) 및 AAC(.m4a) 입니다. 디스플레이항목변경하기 을누릅니다. 디스크유형, 기록형식및설정에따라표시된항목이다를수있습니다. USB 장치 USB 표준과호환되는 MSC(Mass Storage Class) 유형 USB 장치를사용할수있습니다. USB 장치에데이터를백업하는것이좋습니다. USB 표준과호환되는 MSC(Mass Storage Class) 타입의 Android Phone 을사용할수있습니다. Android Phone 에따라 USB 연결모드를 MSC 로설정해야합니다. 참고 엔진을시작한후 USB 장치를연결합니다. USB 장치에따라엔진시동전에연결할경우오작동이발생하거나손상될수있습니다. 해당코덱은 MP3(.mp3), WMA(.wma), AAC(.m4a) 및 AAC(.mp4) 입니다. USB 장치의호환성에대한자세한내용은뒤표지의지원사이트를참조하십시오. USB 장치재생하기 1 USB 커버를연다음 USB 장치를 USB 포트에연결합니다. 재생이시작됩니다. USB 장치가이미연결된경우재생을시작하려면 "USB" 가나타날때까지 를반복해서누릅니다. 재생을중지하려면 를 1초간길게누릅니다. 10 USB 장치를제거하려면 USB 재생을중지한다음 USB 장치를제거하십시오.

33 참고 진동으로인해떨어지거나연결이느슨해질수있으므로너무크거나무거운 USB 장치는사용하지마십시오. USB 데이터가손상될수있으므로 USB 장치의재생도중전면패널을분리하지마십시오. 디스플레이항목변경하기 을누릅니다. USB 장치, 기록형식및설정에따라표시된항목이다를수있습니다. 참고 최대트랙번호는 10,000입니다. 기록된데이터양에따라재생을시작하는데시간이걸릴수있습니다. VBR(Variable Bit Rate) MP3/WMA/ AAC 파일의재생또는빨리감기 / 되감기도중에는경과된재생시간이정확하게표시되지않을수있습니다. 다음 MP3/WMA/AAC 파일의재생은지원되지않습니다. 무손실압축파일 저작권보호파일 DRM(Digital Rights Management) 파일 멀티채널오디오파일 트랙검색및재생하기 다양한모드로트랙재생하기 트랙을반복적으로 ( 반복재생 ) 또는임의순서로 ( 셔플재생 ) 들을수있습니다. 사용가능한재생모드는선택한음원에따라다릅니다. 1 재생중에원하는재생모드가나타날때까지 ( ) 또는 (SHUF) 를반복해서누릅니다. 선택한재생모드로재생을시작하는데시간이걸릴수있습니다. 반복재생 선택 셔플재생 재생 TRACK 트랙을반복합니다. ALBUM 앨범을반복합니다. OFF 트랙을정상순서로 재생합니다 ( 정상재생 ). 선택 SHUF ALBUM SHUF DISC *1 SHUF DEVICE *2 SHUF OFF *1 CD에만해당 *2 USB에만해당 재생 앨범을임의순서로재생합니다. 디스크를임의순서로재생합니다. 장치를임의순서로재생합니다. 트랙을정상순서로재생합니다 ( 정상재생 ). 11

34 이름으로트랙검색하기 Quick-BrowZer CD 또는 USB 장치에서범주별로트랙을쉽게검색할수있습니다. 1 (BROWSE) 를누릅니다 *. Quick-BrowZer 모드로들어가고검색범주목록이표시됩니다. 트랙목록이표시되면원하는검색범주가나타날때까지 (BACK) 을반복해서누릅니다. * 범주목록의시작부분으로바로돌아가려면 USB 재생중에 (BROWSE) 를 2초이상누릅니다. 2 컨트롤다이얼을돌려원하는검색범주를선택한다음눌러서확인합니다. 3 원하는트랙이선택될때까지단계 2를반복합니다. 재생이시작됩니다. Quick-BrowZer 모드를종료하려면 (BROWSE) 를누릅니다. 참고 Quick-BrowZer 모드로들어가면반복 / 셔플설정이취소됩니다. 항목건너뛰기로검색 점프모드 항목이많은범주에서원하는항목을신속하게검색할수있습니다. 1 Quick-BrowZer 모드에서 + 를누릅니다. 항목이름이나타납니다. 2 컨트롤다이얼을돌려원하는항목근처의항목을선택합니다. 목록에서총항목수의 10% 씩목록을건너뜁니다. 3 를누릅니다. 디스플레이는 Quick-BrowZer 모드로돌아가고선택한항목이표시됩니다. 4 컨트롤다이얼을돌려원하는항목을선택하고누릅니다. 선택한항목이트랙인경우재생이시작됩니다. 점프모드를취소하려면 (BACK) 또는 -를누릅니다. 트랙구절을청취하여트랙검색하기 ZAPPIN CD 또는 USB 장치에서짧은트랙구절을순차적으로재생하면서청취할트랙을검색할수있습니다. ZAPPIN 모드는셔플또는셔플반복모드에서트랙을검색하는데적합합니다. 1 재생중에 를누릅니다. 다음트랙의구절에서재생이시작됩니다. 재생시간을선택할수있습니다 (16페이지). 트랙 누름. 2 청취할트랙이재생되면 또는 를누릅니다. 정상재생모드로돌아가서선택한트랙이시작부분부터재생됩니다. (BACK) 을눌러도선택한트랙이재생됩니다. 팁 ZAPPIN 모드에서각트랙의재생부분. 트랙을건너뛰려면 ZAPPIN 모드에서 +/- 를누릅니다. 앨범을건너뛰려면 ZAPPIN 모드에서 / (ALBUM / ) 를누릅니다. 12

35 사운드설정및설정메뉴 정교한사운드기능즐기기 고급사운드엔진 고급사운드엔진은디지털신호처리를사용하여자동차내부의이상적인음장을만듭니다. 음질선택 EQ7 프리셋 7개의이퀄라이저커브 (XPLOD, VOCAL, EDGE, CRUISE, SPACE, GRAVITY, CUSTOM 또는 OFF) 중에서이퀄라이저커브를선택할수있습니다. 1 수신 / 재생중에 를누르고, "SOUND" 가나타날때까지컨트롤다이얼을돌린다음누릅니다. 2 "EQ7 PRESET" 이나타날때까지컨트롤다이얼을돌린다음누릅니다. 3 원하는이퀄라이저커브가나타날때까지컨트롤다이얼을돌린다음누릅니다. 4 (BACK) 을두번누릅니다. 이퀄라이저커브를취소하려면단계 3에서 "OFF" 를선택합니다. 팁 각소스에대한이퀄라이저커브설정을기억할수있습니다. 이퀄라이저커브사용자정의 EQ7 설정 EQ7 의 "CUSTOM" 을사용하면고유한이퀄라이저설정을만들수있습니다. 1 소스를선택한다음 를누르고, "SOUND" 가나타날때까지컨트롤다이얼을돌린다음누릅니다. 2 "EQ7 SETTING" 이나타날때까지컨트롤다이얼을돌린다음누릅니다. 3 "BASE" 가나타날때까지컨트롤다이얼을돌린다음누릅니다. 추가사용자정의를위한기준으로사용할이퀄라이저커브를선택할수있습니다. 4 컨트롤다이얼을돌려이퀄라이저커브를선택한다음누릅니다. 5 이퀄라이저커브를설정합니다. 컨트롤다이얼을돌려주파수범위를선택한다음누릅니다. BAND1: 63 Hz BAND2: 160 Hz BAND3: 400 Hz BAND4: 1 khz BAND5: 2.5 khz BAND6: 6.3 khz BAND7: 16.0 khz 컨트롤다이얼을돌려볼륨레벨을조정한다음누릅니다. 볼륨레벨은 -6dB - +6dB 사이에서 1dB 단위로조정할수있습니다. 단계 및 를반복하여다른주파수범위를조정합니다. 6 이전화면으로돌아가려면 (BACK) 을누릅니다. 이퀄라이저커브가 "CUSTOM" 에저장됩니다. 시간차조정으로사운드최적화 청취위치 본기기에서는사용자위치에맞게각스피커의사운드출력을지연시켜자연스러운음장을시뮬레이션할수있습니다. 13

36 "POSITION" 에사용되는옵션이아래에나와있습니다. FRONT L ( ): 왼쪽전면 FRONT R ( ): 오른쪽전면 FRONT ( ): 전면중앙 ALL ( ): 자동차중앙 OFF: 설정된위치없음 청취위치조정 청취위치설정을미세조정할수있습니다. 1 수신 / 재생중에 를누르고, "SOUND" 가나타날때까지컨트롤다이얼을돌린다음누릅니다. 2 "POSITION" 이나타날때까지컨트롤다이얼을돌린다음누릅니다. 3 "ADJ POSITION" 이나타날때까지컨트롤다이얼을돌린다음누릅니다. 다음경우에는청취위치에서대략적인서브우퍼위치를설정할수도있습니다 : 오디오출력이 "SUB-OUT" 으로설정된경우 (16페이지). 청취위치가 "OFF" 이외의것으로설정된경우. "SET SW POS" 에사용되는옵션이아래에나와있습니다. NEAR ( ): 근처 NORMAL ( ): 일반 FAR ( ): 멀리 1 수신 / 재생중에 를누르고, "SOUND" 가나타날때까지컨트롤다이얼을돌린다음누릅니다. 2 "POSITION" 이나타날때까지컨트롤다이얼을돌린다음누릅니다. 3 "SET F/R POS" 가나타날때까지컨트롤다이얼을돌린다음누릅니다. 4 컨트롤다이얼을돌려 "FRONT L", "FRONT R", "FRONT" 또는 "ALL" 을선택한다음누릅니다. 5 "SET SW POS" 가나타날때까지컨트롤다이얼을돌린다음누릅니다. 6 컨트롤다이얼을돌려 "NEAR", "NORMAL" 또는 "FAR" 중에서서브우퍼위치를선택한다음누릅니다. 4 컨트롤다이얼을돌려청취위치를조정한다음누릅니다. 조정가능한범위 : "+3" - "CENTER" - "-3". 5 이전화면으로돌아가려면 (BACK) 을누릅니다. DM+ 고급기능 DM+ 고급기능은압축프로세스에서손실된높은주파수를복원하여디지털압축사운드를향상시킵니다. 1 재생중에 를누르고, "SOUND" 가나타날때까지컨트롤다이얼을돌린다음누릅니다. 2 "DM+" 가나타날때까지컨트롤다이얼을돌린다음누릅니다. 3 컨트롤다이얼을돌려 "ON" 을선택한다음누릅니다. 4 (BACK) 을두번누릅니다. 팁 튜너이외의각소스별로 DM+ 설정을기억시킬수있습니다. 7 이전화면으로돌아가려면 (BACK) 을누릅니다. 14 청취위치를취소하려면단계 4 에서 "OFF" 를선택합니다.