CDX-GT320MP

Transcription

1 (1) FM/AM Compact Disc Player Operating Instructions GB KR To switch the FM/AM tuning step, see page 4. To cancel the demonstration (DEMO) display, see page 4. CDX-GT320MP

2 Be sure to install this unit in the dashboard of the car for safety. For installation and connections, see the supplied installation/connections manual. Laser diode properties Emission duration: Continuous Laser output: Less than 53.3 μw (This output is the value measured at a distance of about 200 mm from the objective lens surface on the optical pick-up block with 7 mm aperture.) Windows Media is either a registered trademark or trademark of Microsoft Corporation in the United States and/or other countries. This product contains technology subject to certain intellectual property rights of Microsoft. Use or distribution of this technology outside of this product is prohibited without the appropriate license(s) from Microsoft. MPEG Layer-3 audio coding technology and patents licensed from Fraunhofer IIS and Thomson. Note on the lithium battery Do not expose the battery to excessive heat such as direct sunlight, fire or the like. Warning if your car s ignition has no ACC position Be sure to set the Auto Off function (page 11). The unit will shut off completely and automatically in the set time after the unit is turned off, which prevents battery drain. If you do not set the Auto Off function, press and hold until the display disappears each time you turn the ignition off. 2

3 Table of contents Getting Started Switching the FM/AM tuning step Canceling the DEMO mode Setting the clock Detaching the front panel Location of controls Main unit RM-X201 Remote commander Radio Storing and receiving stations RDS CD Playing a disc Playing tracks in various modes Sound Settings and Setup Menu Adjusting setup items Using optional equipment Auxiliary audio equipment Additional Information Precautions Maintenance Specifications Troubleshooting

4 Getting Started Switching the FM/AM tuning step The FM/AM tuning step is factory-set to the 50 khz (FM)/9 khz (AM) position. If the frequency allocation system of your country is based on 200 khz (FM)/10 khz (AM) or 100 khz (FM)/10 khz (AM) step, set the tuning step before use. This setting appears when this unit is turned off. 1 Press, rotate the control dial until GENERAL appears, then press it. 2 Rotate the control dial until TUNER- STP appears, then press it. 3 Rotate the control dial to select from 50K/9K, 100K/10K or 200K/10K, then press it. Receivable frequency by selected frequency setup: FM 50 khz: MHz, MHz, MHz... FM 100 khz: 87.5 MHz, 87.6 MHz, 87.7 MHz... FM 200 khz: 87.5 MHz, 87.7 MHz, 87.9 MHz... AM 9 khz: 531 khz, 540 khz, 549 khz... AM 10 khz: 530 khz, 540 khz, 550 khz... 2 Rotate the control dial until DEMO appears, then press it. 3 Rotate the control dial to select DEMO-OFF, then press it. The setting is complete. 4 Press (BACK) twice. The display returns to normal reception/ play mode. Setting the clock The clock uses a 12-hour digital indication. 1 Press, rotate the control dial until GENERAL appears, then press it. 2 Rotate the control dial until CLOCK- ADJ appears, then press it. The hour indication flashes. 3 Rotate the control dial to set the hour and minute. To move the digital indication, press +/. 4 After setting the minute, press. The setup is complete and the clock starts. To display the clock, press. Canceling the DEMO mode You can cancel the demonstration display which appears while this unit is turned off. 1 Press, rotate the control dial until DISPLAY appears, then press it. 4

5 Detaching the front panel You can detach the front panel of this unit to prevent theft. 1 Press and hold. The unit is turned off. 2 Press the front panel release button, then remove the panel by pulling it towards you. Caution alarm If you turn the ignition switch to the OFF position without detaching the front panel, the caution alarm will sound for a few seconds. The alarm will only sound if the built-in amplifier is used. Note Do not subject the front panel to heat/high temperature or moisture. Avoid leaving it in a parked car or on a dashboard/rear tray. Attaching the front panel Engage part of the front panel with part of the unit, as illustrated, and push the left side into position until it clicks. 5

6 Location of controls Main unit RM-X201 Remote commander Remove the insulation film before use. This section contains instructions on the location of controls and basic operations. SOURCE/OFF button Press to turn on the power; select the source (Radio/CD/AUX). Press and hold for 1 second to turn off the power. Press and hold for more than 2 seconds to turn off the power and the display disappears. SEEK +/ buttons Radio: To tune in stations automatically (press); find a station manually (press and hold). CD: To skip a track (press); skip tracks continuously (press, then press again within about 2 seconds and hold); reverse/fast-forward a track (press and hold). MODE button page 8 To select the radio band (FM/AM). 6

7 Control dial/enter/menu button page 11 Rotate to adjust volume. Press to enter setup mode. Receptor for the remote commander Disc slot Insert the disc (label side up), playback starts. Display window (Eject) button To eject the disc. (BACK) button To return to the previous display. Front panel release button page 5 EQ3 (Equalizer) button page 10 To select an equalizer type (XPLOD, VOCAL, EDGE, CRUISE, SPACE, GRAVITY, CUSTOM or OFF). PTY (Program Type) button page 8 To select PTY in RDS. Number buttons Radio: To receive stored stations (press); store stations (press and hold). CD: / : ALBUM / (during MP3/ WMA playback) To skip an album (press); skip albums continuously (press and hold). : (Repeat)* page 10 : SHUF page 10 : PAUSE To pause playback. Press again to resume playback. DSPL (Display)/SCRL (Scroll) button page 8, 9 To change display items (press); scroll a display item (press and hold). AUX input jack page 12 OFF button To turn off the power; stop the source. SOURCE button Press to turn on the power; select the source (Radio/CD/AUX). ( )/ ( ) buttons To control radio/cd, the same as /+ on the unit. Setup items can be operated by. ENTER button To apply a setting. PTY (Program Type) button VOL (Volume) +*/ button ATT (Attenuate) button To attenuate the sound. To cancel, press again. SOUND/MENU button To enter the SOUND menu directly (press); to enter setup mode (press and hold). DSPL (Display) button (+)/ ( ) buttons To control CD, the same as / on the unit. Setup items can be operated by. SCRL (Scroll) button Number buttons To receive stored stations (press); store stations (press and hold). To pause playback (press ). * This button has a tactile dot. Note If the unit is turned off and the display disappears, the unit cannot be operated with the remote commander unless on the unit is pressed, or a disc is inserted to activate the unit first. 7

8 Radio Storing and receiving stations Tuning step setting is required (page 4). Notes If the tuning step setting is changed, the stored stations will be erased. If replacing the car battery or changing the connections, the tuning step setting will be erased, and you will need to set again. Caution When tuning in stations while driving, use Best Tuning Memory (BTM) to prevent an accident. Receiving the stored stations 1 Select the band, then press a number button ( to ). Tuning automatically 1 Select the band, then press +/ to search for the station. Scanning stops when the unit receives a station. Repeat this procedure until the desired station is received. Tip If you know the frequency of the station you want to listen to, press and hold +/ to locate the approximate frequency, then press +/ repeatedly to fine adjust to the desired frequency (manual tuning). Storing automatically BTM 1 Press repeatedly until TUNER appears. To change the band, press repeatedly. You can select from FM1, FM2, FM3, AM1 or AM2. 2 Press, rotate the control dial until GENERAL appears, then press it. 3 Rotate the control dial until BTM appears, then press it. The unit stores stations in order of frequency on the number buttons. RDS FM stations with Radio Data System (RDS) service send inaudible digital information along with the regular radio program signal. Notes Depending on the country/region, not all RDS functions may be available. RDS will not work if the signal strength is too weak, or if the station you are tuned to is not transmitting RDS data. Changing display items Press. 8 Storing manually 1 While receiving the station that you want to store, press and hold a number button ( to ) until MEMORY appears. Selecting PTY (Program Types) Use PTY to display or search for a desired program type. 1 Press during FM reception. The current program type name appears if the station is transmitting PTY data.

9 2 Rotate the control dial until the desired program type appears, then press it. The unit starts to search for a station broadcasting the selected program type. Type of programs NEWS (News), AFFAIRS (Current Affairs), INFO (Information), SPORT (Sports), EDUCATE (Education), DRAMA (Drama), CULTURE (Culture), SCIENCE (Science), VARIED (Varied), POP M (Pop Music), ROCK M (Rock Music), EASY M (M.O.R. Music), LIGHT M (Light classical), CLASSICS (Serious classical), OTHER M (Other Music), WEATHER (Weather), FINANCE (Finance), CHILDREN (Children s program), SOCIAL A (Social Affairs), RELIGION (Religion), PHONE IN (Phone In), TRAVEL (Travel), LEISURE (Leisure), JAZZ (Jazz Music), COUNTRY (Country Music), NATION M (National Music), OLDIES (Oldies Music), FOLK M (Folk Music), DOCUMENT (Documentary) CD Playing a disc This unit can play CD-DA (also containing CD TEXT) and CD-R/CD-RW (MP3/ WMA files (page 14)). 1 Insert the disc (label side up). Playback starts automatically. To eject the disc, press. Note Corresponding codec is MP3 (.mp3) and WMA (.wma). Changing display items Press. Displayed items may differ depending on the disc type, recording format and settings. Note You may receive a different radio program from the one you select. Setting CT (Clock Time) The CT data from the RDS transmission sets the clock. 1 Set CT-ON in setup (page 11). Note The CT function may not work properly even though an RDS station is being received. 9

10 Playing tracks in various modes You can listen to tracks repeatedly (repeat play) or in random order (shuffle play). 1 During playback, press ( ) or (SHUF) repeatedly until the desired play mode appears. Repeat play Select TRACK ALBUM* OFF Shuffle play Select SHUF ALBUM* SHUF DISC SHUF OFF To play track repeatedly. album repeatedly. track in normal order (Normal play). To play album in random order. disc in random order. track in normal order (Normal play). Sound Settings and Setup Menu Customizing the equalizer curve EQ3 CUSTOM of EQ3 allows you to make your own equalizer settings. 1 During reception/playback, press repeatedly to select CUSTOM, then press (BACK). 2 Press. 3 Rotate the control dial until SOUND appears, then press it. 4 Rotate the control dial until EQ3 LOW, EQ3 MID or EQ3 HIGH appears, then press it. 5 Rotate the control dial to adjust the selected item, then press it. The volume level is adjustable in 1 db steps, from 10 db to +10 db. *When an MP3/WMA is played. Repeat steps 4 and 5 to adjust the equalizer curve. To restore the factory-set equalizer curve, press and hold before the setting is complete. 6 Press (BACK) twice. The display returns to normal reception/ play mode. 10

11 Adjusting setup items 1 Press, rotate the control dial until the desired category appears, then press it. 2 Rotate the control dial until the desired item appears, then press it. 3 Rotate the control dial to select the setting, then press it.* The setting is complete. 4 Press (BACK) to return to the previous display. * For CLOCK-ADJ, TUNER-STP and BTM settings, step 4 is not necessary. The following items can be set depending on the source and setting: GENERAL: CLOCK-ADJ (Clock Adjust) (page 4) TUNER-STP* 1 (Tuner Step) (page 4) CAUT ALM* 1 (Caution Alarm) Activates the caution alarm: ON, OFF (page 5). BEEP Activates the beep sound: ON, OFF. AUTO OFF Shuts off automatically after a desired time when the unit is turned off: NO, 30S (Seconds), 30M (Minutes), 60M (Minutes). AUX-A* 1 (AUX Audio) Activates the AUX source display: ON, OFF (page 12). REAR/SUB* 1 Switches the audio output: REAR- OUT (power amplifier), SUB-OUT (subwoofer). CT (Clock Time) Activates the CT function: ON, OFF (page 9). BTM* 2 (page 8) *1 When the unit is turned off. *2 When the tuner is selected. SOUND: EQ3 LOW* 1 (page 10) EQ3 MID* 1 (page 10) EQ3 HIGH* 1 (page 10) BALANCE Adjusts the sound balance: RIGHT-15 (R15) CENTER (0) LEFT-15 (L15). FADER Adjusts the relative level: FRONT-15 (F15) CENTER (0) REAR-15 (R15). LOUDNESS Reinforces bass and treble for clear sound at low volume levels: ON, OFF. S.WOOFER* 2 (Subwoofer) SW LEVEL (Subwoofer Level) Adjusts the subwoofer volume level: +10 db 0 db 10 db. ( ATT is displayed at the lowest setting.) SW PHASE (Subwoofer Phase) Selects the subwoofer phase: SUB NORM, SUB REV. LPF (Low Pass Filter) Selects the subwoofer cut-off frequency: OFF, 80Hz, 100Hz, 120Hz, 140Hz, 160Hz. HPF (High Pass Filter) Selects the front/rear speaker cut-off frequency: OFF, 80Hz, 100Hz, 120Hz, 140Hz, 160Hz. 11

12 AUX VOL* 3 (AUX Volume Level) Adjusts the volume level for each connected auxiliary equipment: +18 db 0 db 8 db. This setting negates the need to adjust the volume level between sources. *1 When EQ3 is activated (page 10). *2 When the audio output is set to SUB-OUT. *3 When the AUX is selected. DISPLAY: DEMO (Demonstration) Activates the demonstration: ON, OFF. BLK OUT (Black Out) Turns off the illumination automatically for any source (e.g., during radio reception/cd playback, etc.) if no operation is performed for 5 seconds: ON, OFF. To turn the light back on, press any button on the unit or the remote commander. Using optional equipment Auxiliary audio equipment By connecting an optional portable audio device to the AUX input jack (stereo mini jack) on the unit and then simply selecting the source, you can listen on your car speakers. Connecting the portable audio device 1 Turn off the portable audio device. 2 Turn down the volume on the unit. 3 Connect the portable audio device to the unit with a connecting cord (not supplied)*. * Be sure to use a straight type plug. DIMMER Changes the display brightness: ON, OFF. AUTO SCR* (Auto Scroll) Scrolls long items automatically: ON, OFF. M.DISPLAY (Motion Display) ON : to show moving patterns. OFF : to deactivate the Motion Display. * When the CD is selected. Adjusting the volume level Be sure to adjust the volume for each connected audio device before playback. 1 Turn down the volume on the unit. 2 Press repeatedly until AUX appears. 3 Start playback of the portable audio device at a moderate volume Set your usual listening volume on the unit. 5 Adjust the input level (page 12).

13 Additional Information Precautions Cool off the unit beforehand if your car has been parked in direct sunlight. Do not leave the front panel or audio devices brought in inside the car, or it may cause malfunction due to high temperature in direct sunlight. Power antenna (aerial) extends automatically. Moisture condensation Should moisture condensation occur inside the unit, remove the disc and wait for about an hour for it to dry out; otherwise the unit will not operate properly. To maintain high sound quality Do not splash liquid onto the unit or discs. Notes on discs Do not expose discs to direct sunlight or heat sources such as hot air ducts, nor leave it in a car parked in direct sunlight. Before playing, wipe the discs with a cleaning cloth from the center out. Do not use solvents such as benzine, thinner, commercially available cleaners. This unit is designed to play back discs that conform to the Compact Disc (CD) standard. DualDiscs and some of the music discs encoded with copyright protection technologies do not conform to the Compact Disc (CD) standard, therefore, these discs may not be playable by this unit. Discs that this unit CANNOT play Discs with labels, stickers, or sticky tape or paper attached. Doing so may cause a malfunction, or may ruin the disc. Discs with non-standard shapes (e.g., heart, square, star). Attempting to do so may damage the unit. 8 cm (3 1 /4 in) discs. Notes on CD-R/CD-RW discs The maximum number of: (CD-R/CD-RW only) folders (albums): 150 (including root folder) files (tracks) and folders: 300 (may less than 300 if folder/file names contain many characters) displayable characters for a folder/file name: 32 (Joliet)/64 (Romeo) If the multi-session disc begins with a CD- DA session, it is recognized as a CD-DA disc, and other sessions are not played back. Discs that this unit CANNOT play CD-R/CD-RW of poor recording quality. CD-R/CD-RW recorded with an incompatible recording device. CD-R/CD-RW which is finalized incorrectly. CD-R/CD-RW other than those recorded in music CD format or MP3 format conforming to ISO9660 Level 1/Level 2, Joliet/Romeo or multi-session. Playback order of MP3/WMA files MP3/WMA Folder (album) MP3/WMA file (track) 13

14 About MP3 files MP3, which stands for MPEG-1 Audio Layer-3, is a music file compression format standard. It compresses audio CD data to approximately 1/10 of its original size. ID3 tag versions 1.0, 1.1, 2.2, 2.3 and 2.4 apply to MP3 only. ID3 tag is 15/30 characters (1.0 and 1.1), or 63/126 characters (2.2, 2.3 and 2.4). When naming an MP3 file, be sure to add the file extension.mp3 to the file name. During playback or fast-forward/reverse of a VBR (Variable Bit Rate) MP3 file, elapsed playing time may not display accurately. Maintenance Replacing the lithium battery of the remote commander When the battery becomes weak, the range of the remote commander becomes shorter. Replace the battery with a new CR2025 lithium battery. Use of any other battery may present a risk of fire or explosion. + side up Note If you play a high-bit-rate MP3, such as 320 kbps, sound may be intermittent. About WMA files WMA, which stands for Windows Media Audio, is a music file compression format standard. It compresses audio CD data to approximately 1/22* of its original size. WMA tag is 63 characters. When naming a WMA file, be sure to add the file extension.wma to the file name. During playback or fast-forward/reverse of a VBR (Variable Bit Rate) WMA file, elapsed playing time may not display accurately. *only for 64 kbps Note Playback of the following WMA files is not supported. lossless compression copyright-protected If you have any questions or problems concerning your unit that are not covered in this manual, consult your nearest Sony dealer. Notes on the lithium battery Keep the lithium battery out of the reach of children. Should the battery be swallowed, immediately consult a doctor. Wipe the battery with a dry cloth to assure a good contact. Be sure to observe the correct polarity when installing the battery. Do not hold the battery with metallic tweezers, otherwise a short-circuit may occur. WARNING Battery may explode if mistreated. Do not recharge, disassemble, or dispose of in fire. Cleaning the connectors The unit may not function properly if the connectors between the unit and the front panel are not clean. In order to prevent this, detach the front panel (page 5) and clean the connectors with a cotton swab. Do not apply too much force. Otherwise, the connectors may be damaged. 14

15 Notes For safety, turn off the ignition before cleaning the connectors, and remove the key from the ignition switch. Never touch the connectors directly with your fingers or with any metal device. Specifications Tuner section FM Tuning range: MHz (at 50 khz step) MHz (at 100 khz step) MHz (at 200 khz step) FM tuning step: 50 khz/100 khz/200 khz switchable Antenna (aerial) terminal: External antenna (aerial) connector Intermediate frequency: 25 khz Usable sensitivity: 8 dbf Selectivity: 75 db at 400 khz Signal-to-noise ratio: 80 db (stereo) Separation: 50 db at 1 khz Frequency response: 20 15,000 Hz AM Tuning range: 531 1,602 khz (at 9 khz step) 530 1,710 khz (at 10 khz step) AM tuning step: 9 khz/10 khz switchable Antenna (aerial) terminal: External antenna (aerial) connector Intermediate frequency: 9,124.5 khz or 9,115.5 khz/4.5 khz (at 9 khz step) 9,115 khz or 9,125 khz/5 khz (at 10 khz step) Sensitivity: 26 μv General Outputs: Audio outputs terminal (rear/sub switchable) Power antenna (aerial)/power amplifier control terminal (REM OUT) Inputs: Remote controller input terminal Antenna (aerial) input terminal AUX input jack (stereo mini jack) Tone controls: Low: ±10 db at 60 Hz (XPLOD) Mid: ±10 db at 1 khz (XPLOD) High: ±10 db at 10 khz (XPLOD) Power requirements: 12 V DC car battery (negative ground (earth)) Dimensions: Approx mm (7 1 /8 2 7 in) (w/h/d) Mounting dimensions: Approx mm (7 1 /4 2 1 /8 6 5 /16 in) (w/h/d) Mass: Approx. 1.2 kg (2 lb 11 oz) Supplied accessories: Remote commander: RM-X201 Parts for installation and connections (1 set) Your dealer may not handle some of the above listed accessories. Please ask the dealer for detailed information. Design and specifications are subject to change without notice. CD Player section Signal-to-noise ratio: 120 db Frequency response: 10 20,000 Hz Wow and flutter: Below measurable limit Power amplifier section Output: Speaker outputs Speaker impedance: 4 8 ohms Maximum power output: 52 W 4 (at 4 ohms) 15

16 16 Troubleshooting The following checklist will help you remedy problems you may encounter with your unit. Before going through the checklist below, check the connection and operating procedures. For details on using the fuse and removing the unit from the dashboard, refer to the installation/connections manual supplied with this unit. General No power is being supplied to the unit. Check the connection or fuse. If the unit is turned off and the display disappears, the unit cannot be operated with the remote commander. Turn on the unit. The power antenna (aerial) does not extend. The power antenna (aerial) does not have a relay box. No sound. The ATT function is activated. The position of the fader control FAD is not set for a 2-speaker system. No beep sound. The beep sound is canceled (page 11). An optional power amplifier is connected and you are not using the built-in amplifier. The contents of the memory have been erased. The power supply lead or battery has been disconnected or not connected properly. The unit is reset. Store again in the memory. Stored stations and correct time are erased. The fuse has blown. Makes noise when the position of the ignition is switched. The leads are not matched correctly with the car s accessory power connector. During playback or reception, demonstration mode starts. If no operation is performed for 5 minutes with DEMO-ON set, demonstration mode starts. Set DEMO-OFF (page 12). The display disappears from/does not appear in the display window. The dimmer is set to DIMMER-ON (page 12). The display disappears if you press and hold. Press on the unit until the display appears. The connectors are dirty (page 14). The Auto Off function does not operate. The unit is turned on. The Auto Off function activates after turning off the unit. Turn off the unit. The display disappears while the unit is operating. The Black Out function is set to on (page 12). The operation buttons do not function. The disc will not eject. Press and (BACK) for more than 2 seconds. The contents stored in memory are erased. For your safety, do not perform the reset operation while you are driving. Radio reception The stations cannot be received. The sound is hampered by noises. The connection is not correct. Connect an REM OUT lead (blue/white striped) or accessory power supply lead (red) to the power supply lead of a car s antenna (aerial) booster (only when your car has built-in radio antenna (aerial) in the rear/ side glass). Check the connection of the car antenna (aerial). If the auto antenna (aerial) will not go up, check the connection of the power antenna (aerial) control lead. The tuning step setting has been erased. Set the tuning step again (page 4).

17 Preset tuning is not possible. Store the correct frequency in the memory. The broadcast signal is too weak. Automatic tuning is not possible. The broadcast signal is too weak. Perform manual tuning. RDS PTY displays The current station is not an RDS station. RDS data has not been received. The station does not specify the program type. CD playback The disc cannot be loaded. Another disc is already loaded. The disc has been forcibly inserted upside down or in the wrong way. The disc does not play back. Defective or dirty disc. The CD-Rs/CD-RWs are not for audio use (page 13). MP3/WMA files cannot be played back. The disc is incompatible with the MP3/WMA format and version (page 13). MP3/WMA files take longer to play back than others. The following discs take a longer time to start playback. A disc recorded with a complicated tree structure. A disc recorded in Multi Session. A disc to which data can be added. The display items do not scroll. For discs with very many characters, those may not scroll. AUTO SCR is set to OFF. Set AUTO SCR-ON (page 12). Press and hold (SCRL). The sound skips. Installation is not correct. Install the unit at an angle of less than 45 in a sturdy part of the car. Defective or dirty disc. The disc will not eject. Press (eject) (page 6). Error displays/messages ERROR The disc is dirty or inserted upside down. Clean or insert the disc correctly. A blank disc has been inserted. The disc cannot play due to a problem. Insert another disc. Press (eject) to remove the disc. FAILURE The connection of speakers/amplifiers is incorrect. See the installation/connections manual of this model to check the connection. NO MUSIC The disc does not contain a music file. Insert a music CD in this unit. NO NAME A disc/album/artist/track name is not written in the track. OFFSET There may be an internal malfunction. Check the connection. If the error indication remains on in the display, consult your nearest Sony dealer. PUSH EJT (Push Eject) The disc cannot be ejected. Press (eject) (page 6). READ The unit is reading all track and album information on the disc. Wait until reading is complete and playback starts automatically. Depending on the disc structure, it may take more than a minute. or During reverse or fast-forward, you have reached the beginning or the end of the disc and you cannot go any further. 17

18 The character cannot be displayed with the unit. If these solutions do not help improve the situation, consult your nearest Sony dealer. If you take the unit to be repaired because of CD playback trouble, bring the disc that was used at the time the problem began. 18

19

20 레이저다이오드속성방사지속시간 : 연속레이저출력 : 53.3 μw 미만 ( 이출력은 Optical Pick-up Block 의대물렌즈표면에서 7 mm 조리개를사용하여약 200 mm 의거리에서측정한값입니다.) 자동차시동키에 ACC 위치가없을경우의경고자동꺼짐기능을설정하십시오 (11 페이지 ). 기기가꺼지고설정된시간이지나면자동으로완전히종료되므로배터리소모가방지됩니다. 자동꺼짐기능을설정하지않은경우시동키를끌때마다디스플레이가사라질때까지 를누르고계십시오. 2

21 목차 시작하기 FM/AM 튜닝단위전환하기 DEMO 모드취소하기 시계설정하기 전면패널분리하기 컨트롤위치 본체 RM-X201 리모컨 라디오 방송국저장및수신하기 RDS CD 디스크재생하기 다양한모드로트랙재생하기 사운드설정및설정메뉴 설정항목조정하기 옵션장비사용하기 보조오디오장비 추가정보 사용전주의사항 유지관리 주요제원 문제해결

22 시작하기 FM/AM 튜닝단위전환하기 FM/AM 튜닝단위는출하시 50 khz (FM)/9 khz(am) 로설정되어있습니다. 해당국가의주파수할당방식이 200 khz (FM)/10 khz(am) 또는 100 khz(fm)/ 10 khz(am) 단위에기반을두는경우사용전에튜닝단위를설정하십시오. 이설정은기기의전원이꺼진경우표시됩니다. 1 를누르고, "GENERAL" 이나타날때까지컨트롤다이얼을돌린다음누릅니다. 2 "TUNER-STP" 가나타날때까지컨트롤다이얼을돌린다음누릅니다. 3 컨트롤다이얼을돌려 "50K/9K", "100K/10K" 또는 "200K/10K" 를선택한다음누릅니다. 선택한주파수설정별수신가능주파수 : FM 50 khz: MHz, MHz, MHz... FM 100 khz: 87.5 MHz, 87.6 MHz, 87.7 MHz... FM 200 khz: 87.5 MHz, 87.7 MHz, 87.9 MHz... AM 9 khz: 531 khz, 540 khz, 549 khz... AM 10 khz: 530 khz, 540 khz, 550 khz... 2 "DEMO" 가나타날때까지컨트롤다이얼을돌린다음누릅니다. 3 컨트롤다이얼을돌려 "DEMO-OFF" 를선택한다음누릅니다. 설정이완료되었습니다. 4 (BACK) 을두번누릅니다. 디스플레이가일반수신 / 재생모드로돌아갑니다. 시계설정하기 시계에는 12시간디지털표기가사용됩니다. 1 를누르고, "GENERAL" 이나타날때까지컨트롤다이얼을돌린다음누릅니다. 2 "CLOCK-ADJ" 가나타날때까지컨트롤다이얼을돌린다음누릅니다. 시간표시가깜박입니다. 3 컨트롤다이얼을돌려시간과분을설정합니다. 디지털표시를이동하려면 +/- 를누릅니다. 4 분을설정한후 를누릅니다. 설정이완료되었으며시계가시작됩니다. 시계를표시하려면 을누릅니다. DEMO 모드취소하기 기기의전원이꺼질때표시되는데모를취소할수있습니다. 1 를누르고 "DISPLAY" 가나타날때까지컨트롤다이얼을돌린다음누릅니다. 4

23 전면패널분리하기 도난방지를위해본기기의전면패널을분리할수있습니다. 1 을길게누릅니다. 기기가꺼집니다. 2 전면패널해제버튼 를누른다음앞으로당겨패널을제거합니다. 경고성알람전면패널을분리하지않고시동키를 OFF 쪽에놓을경우경고성알람이몇초간울립니다. 알람은내장앰프가사용된경우에만울립니다. 참고 전면패널을고온다습한곳에두지마십시오. 주차한차량에그대로두거나계기판이나뒷좌석트렁크위에놓지마십시오. 전면패널부착하기 그림과같이전면패널의 부위를기기의 부위에결합하여찰칵소리가날때까지왼쪽을누릅니다. 5

24 컨트롤위치 본체 RM-X201 리모컨 사용전에절연필름을제거하십시오. 이단원에서는컨트롤위치와기본조작에대한지침이제공됩니다. SOURCE/OFF 버튼전원을켜거나소스 ( 라디오 /CD/AUX) 를선택합니다. 전원을끄려면 1초간길게누릅니다. 전원을끄고디스플레이를사라지게하려면 2초이상길게누릅니다. SEEK +/- 버튼라디오 : 방송국을자동튜닝하거나 ( 누르기 ), 방송국을수동으로찾습니다 ( 길게누르기 ). CD: 트랙을건너뛰거나 ( 누르기 ), 트랙을연속건너뛰거나 ( 누른다음약 2초내에다시길게누르기 ), 트랙되감기 / 빨리감기를합니다 ( 길게누르기 ). MODE 버튼 8 페이지라디오대역 (FM/AM) 을선택합니다. 6

25 컨트롤다이얼 /ENTER/MENU 버튼 11페이지볼륨을조정하려면돌립니다. 설정모드로들어가려면누릅니다. 리모컨수신부 디스크슬롯디스크를넣으면 ( 라벨면이윗면 ) 재생이시작됩니다. 디스플레이창 ( 꺼내기 ) 버튼디스크를꺼냅니다. (BACK) 버튼이전디스플레이로돌아가려면누릅니다. 전면패널해제버튼 5페이지 EQ3( 이퀄라이저 ) 버튼 10페이지이퀄라이저유형 (XPLOD, VOCAL, EDGE, CRUISE, SPACE, GRAVITY, CUSTOM 또는 OFF) 을선택합니다. PTY( 프로그램유형 ) 버튼 8페이지 RDS에서 PTY를선택합니다. 숫자버튼라디오 : 저장된방송국을수신하거나 ( 누르기 ), 방송국을저장합니다 ( 길게누르기 ). CD: / : ALBUM / (MP3/WMA 재생도중 ) 앨범을건너뛰거나 ( 누르기 ), 앨범을연속으로건너뜁니다 ( 길게누르기 ). : ( 반복 )* 10페이지 : SHUF 10페이지 : PAUSE 재생을일시정지합니다. 재생을다시시작하려면다시누릅니다. DSPL( 디스플레이 )/SCRL( 스크롤 ) 버튼 8, 9페이지디스플레이항목을변경하거나 ( 누르기 ), 디스플레이항목을스크롤합니다 ( 길게누르기 ). AUX 입력잭 12페이지 OFF 버튼전원을끄거나, 소스를중지합니다. SOURCE 버튼전원을켜거나소스 ( 라디오 /CD/AUX) 를선택합니다. ( )/ ( ) 버튼라디오 /CD를제어합니다. 기기의 -/+ 와동일합니다. 설정항목은 를사용하여조작할수있습니다. ENTER 버튼설정을적용합니다. PTY( 프로그램유형 ) 버튼 VOL( 볼륨 ) +*/- 버튼 ATT( 약화 ) 버튼사운드를약화시킵니다. 취소하려면다시누릅니다. SOUND/MENU 버튼 SOUND 메뉴로바로들어가거나 ( 누르기 ) 설정모드로들어갑니다 ( 길게누르기 ). DSPL( 디스플레이 ) 버튼 (+)/ (-) 버튼 CD를제어합니다. 기기의 / 와동일합니다. 설정항목은 를사용하여조작할수있습니다. SCRL( 스크롤 ) 버튼 숫자버튼저장된방송국을수신하거나 ( 누르기 ), 방송국을저장합니다 ( 길게누르기 ). 재생을일시정지합니다 ( 누르기 ). * 이버튼에는돌기가있습니다. 참고 기기가꺼지고디스플레이가사라진경우기기에서 를누르거나디스크를넣어기기를활성화한후에만리모컨으로조작할수있습니다. 7

26 라디오 방송국저장및수신하기 튜닝단위를설정해야합니다 (4 페이지 ). 참고 튜닝단위설정이변경된경우저장된방송국이지워집니다. 자동차배터리를교체하거나연결을변경한경우튜닝단위설정이지워지므로다시설정해야합니다. 주의운전중에방송국을튜닝할때는사고를방지하기위해 BTM(Best Tuning Memory) 을사용하십시오. 저장된방송국수신하기 1 대역을선택하고숫자버튼 ( - ) 을누릅니다. 자동으로튜닝하기 1 대역을선택한다음 +/- 를눌러방송국을검색합니다. 방송국이수신되면스캔이중지됩니다. 원하는방송국이수신될때까지이절차를반복합니다. 팁 청취할방송국의주파수를알고있는경우 +/- 를길게눌러원하는주파수에가까워지면 +/- 를반복해서눌러해당주파수로미세조정합니다 ( 수동튜닝 ). 자동으로저장하기 BTM 1 "TUNER" 가나타날때까지 를반복해서누릅니다. 대역을변경하려면 를반복해서누릅니다. FM1, FM2, FM3, AM1 또는 AM2를선택할수있습니다. 2 를누르고, "GENERAL" 이나타날때까지컨트롤다이얼을돌린다음누릅니다. 3 "BTM" 이나타날때까지컨트롤다이얼을돌린다음누릅니다. 숫자버튼의주파수순서대로방송국이저장됩니다. 수동으로저장하기 1 저장할방송국이수신되는상태에서 "MEMORY" 가나타날때까지숫자버튼 ( - ) 을길게누릅니다. RDS RDS(Radio Data System) 서비스가있는 FM 방송국은귀에들리지않는디지털정보를일반라디오프로그램신호와함께전송합니다. 참고 국가 / 지역에따라일부 RDS 기능을사용하지못할수있습니다. 신호강도가너무약하거나튜닝한방송국에서 RDS 데이터를전송하지않는경우 RDS 가작동되지않습니다. 디스플레이항목변경하기 을누릅니다. PTY( 프로그램유형 ) 선택하기 PTY 를사용하여원하는프로그램유형을표시하거나검색합니다. 8

27 1 FM 수신중에 를누릅니다. 방송국에서 PTY 데이터를전송하는중이면현재프로그램유형이름이나타납니다. 2 원하는프로그램유형이나타날때까지컨트롤다이얼을돌린다음누릅니다. 선택된프로그램유형을방송하는방송국이검색되기시작합니다. 프로그램유형 NEWS( 뉴스 ), AFFAIRS( 시사 ), INFO ( 정보 ), SPORT( 스포츠 ), EDUCATE ( 교육 ), DRAMA( 드라마 ), CULTURE ( 문화 ), SCIENCE( 과학 ), VARIED ( 기타 ), POP M( 팝음악 ), ROCK M ( 락음악 ), EASY M(M.O.R. 음악 ), LIGHT M( 가벼운클래식 ), CLASSICS ( 정통클래식 ), OTHER M( 기타음악 ), WEATHER( 날씨 ), FINANCE( 금융 ), CHILDREN( 어린이프로그램 ), SOCIAL A( 사회문제 ), RELIGION ( 종교 ), PHONE IN( 전화참가 ), TRAVEL( 여행 ), LEISURE( 레저 ), JAZZ( 재즈음악 ), COUNTRY( 컨츄리음악 ), NATION M( 민속음악 ), OLDIES( 흘러간노래 ), FOLK M( 포크음악 ), DOCUMENT( 다큐멘터리 ) CD 디스크재생하기 본기기에서는 CD-DA(CD TEXT도포함 ) 및 CD-R/CD-RW(MP3/WMA 파일 (14페이지)) 을재생할수있습니다. 1 디스크를넣습니다 ( 라벨면이윗면 ). 자동으로재생이시작됩니다. 디스크를꺼내려면 을누릅니다. 참고 해당코덱은 MP3(.mp3) 및 WMA(.wma) 입니다. 디스플레이항목변경하기 을누릅니다. 디스크유형, 기록형식및설정에따라표시된항목이다를수있습니다. 참고 선택한것과다른라디오프로그램이수신될수있습니다. CT( 시계시간 ) 설정하기 RDS 전송에포함된 CT 데이터는시계를설정합니다. 1 설정에서 "CT-ON" 을설정합니다 (11페이지). 참고 RDS 방송국을수신중인경우에도 CT 기능이제대로작동하지않을수있습니다. 9

28 다양한모드로트랙재생하기 트랙을반복적으로 ( 반복재생 ) 또는임의순서로 ( 셔플재생 ) 들을수있습니다. 1 재생중에원하는재생모드가나타날때까지 ( ) 또는 (SHUF) 를반복해서누릅니다. 반복재생 선택 셔플재생 선택 재생 TRACK 트랙을반복합니다. ALBUM* 앨범을반복합니다. OFF 트랙을정상순서로재생합니다 ( 정상재생 ). SHUF ALBUM* SHUF DISC SHUF OFF 재생 * MP3/WMA 를재생하는경우. 앨범을임의순서로재생합니다. 디스크를임의순서로재생합니다. 트랙을정상순서로재생합니다 ( 정상재생 ). 사운드설정및설정메뉴 이퀄라이저커브사용자정의 EQ3 EQ3의 "CUSTOM" 을사용하면고유한이퀄라이저설정을만들수있습니다. 1 수신 / 재생중에 를반복해서눌러 "CUSTOM" 을선택한다음 (BACK) 을누릅니다. 2 를누릅니다. 3 "SOUND" 가나타날때까지컨트롤다이얼을돌린다음누릅니다. 4 "EQ3 LOW", "EQ3 MID" 또는 "EQ3 HIGH" 가나타날때까지컨트롤다이얼을돌린다음누릅니다. 5 컨트롤다이얼을돌려선택한항목을조정하고누릅니다. 볼륨레벨은 -10 db db 사이에서 1dB 단위로조정할수있습니다. 이퀄라이저커브를조정하려면단계 4 와 5 를반복합니다. 출하시설정된이퀄라이저커브로복원하려면설정이완료되기전에 를길게누릅니다. 6 (BACK) 을두번누릅니다. 디스플레이가일반수신 / 재생모드로돌아갑니다. 10

29 설정항목조정하기 1 를누르고, 원하는범주가나타날때까지컨트롤다이얼을돌린다음누릅니다. 2 원하는항목이나타날때까지컨트롤다이얼을돌린다음누릅니다. 3 컨트롤다이얼을돌려설정을선택한다음누릅니다.* 설정이완료되었습니다. 4 이전화면으로돌아가려면 (BACK) 을누릅니다. * CLOCK-ADJ, TUNER-STP 및 BTM 설정의경우단계 4 가필요하지않습니다. 소스및설정에따라다음항목을설정할수있습니다 : GENERAL: CLOCK-ADJ( 시계조정 )(4 페이지 ) TUNER-STP* 1 ( 튜너단위 )(4 페이지 ) CAUT ALM* 1 ( 경고성알람 ) 경고성알람활성화 : "ON", "OFF" (5 페이지 ). BEEP 비프음활성화 : "ON", "OFF". AUTO OFF 기기가꺼진경우원하는시간후자동으로종료 : "NO", "30S( 초 )", "30M ( 분 )", "60M( 분 )". AUX-A* 1 (AUX 오디오 ) AUX 소스표시활성화 : "ON", "OFF"(12 페이지 ). REAR/SUB* 1 오디오출력전환 : "REAR-OUT"( 전원앰프 ), "SUB-OUT"( 서브우퍼 ). CT( 시계시간 ) CT 기능활성화 : "ON", "OFF"(9 페이지 ). BTM* 2 (8 페이지 ) *1 기기가꺼진경우. *2 튜너가선택된경우. SOUND: EQ3 LOW* 1 (10 페이지 ) EQ3 MID* 1 (10 페이지 ) EQ3 HIGH* 1 (10 페이지 ) BALANCE 사운드밸런스조정 : "RIGHT-15 (R15)" - "CENTER (0)" - "LEFT-15 (L15)". FADER 상대레벨조정 : "FRONT-15 (F15)" - "CENTER (0)" - "REAR-15 (R15)". LOUDNESS 낮은볼륨레벨에서사운드가분명하도록저음및고음강화 : "ON", "OFF". S.WOOFER* 2 ( 서브우퍼 ) SW LEVEL( 서브우퍼레벨 ) 서브우퍼볼륨레벨조정 : "+10 db" - "0 db" - "-10 db". ( 가장낮은설정에서 "ATT" 가표시됩니다.) SW PHASE( 서브우퍼위상 ) 서브우퍼위상선택 : "SUB NORM", "SUB REV". LPF( 저역통과필터 ) 서브우퍼컷오프주파수선택 : "OFF", "80Hz", "100Hz", "120Hz", "140Hz", "160Hz". HPF( 고역통과필터 ) 전면 / 후면스피커컷오프주파수선택 : "OFF", "80Hz", "100Hz", "120Hz", "140Hz", "160Hz". 11

30 AUX VOL* 3 (AUX 볼륨레벨 ) 연결된각보조장비의볼륨레벨조정 : "+18 db" - "0 db" - "-8 db". 이설정을사용하면소스간의볼륨레벨을조정할필요가없습니다. *1 EQ3가활성화된경우 (10페이지). *2 오디오출력이 "SUB-OUT" 으로설정된경우. *3 AUX가선택된경우. 옵션장비사용하기 보조오디오장비 옵션휴대용오디오장치를기기의 AUX 입력잭 ( 스테레오미니잭 ) 에연결하고소스를선택하여자동차스피커로들을수있습니다. DISPLAY: DEMO( 데모 ) 데모활성화 : "ON", "OFF". BLK OUT( 블랙아웃 ) 5 초간조작하지않으면소스 ( 예 : 라디오수신 /CD 재생도중 ) 조명자동끄기 : "ON", "OFF". 조명을다시켜려면기기또는리모컨에서아무버튼이나누릅니다. 휴대용오디오장치연결 1 휴대용오디오장치를끕니다. 2 기기의볼륨을낮춥니다. 3 연결코드 ( 별매품 )* 를사용하여휴대용오디오장치를기기에연결합니다. * 직선형플러그를사용해야합니다. DIMMER 디스플레이밝기변경 : "ON", "OFF" AUTO SCR*( 자동스크롤 ) 긴항목을자동으로스크롤 : "ON", "OFF". M.DISPLAY( 동작표시 ) "ON": 움직이는패턴표시. "OFF": 모션표시비활성화. * CD 를선택한경우. 볼륨레벨조정하기 재생전에연결된각오디오장치의볼륨을조정합니다. 1 기기의볼륨을낮춥니다. 2 "AUX" 가나타날때까지 를반복해서누릅니다. 3 적절한볼륨으로휴대용오디오장치의재생을시작합니다. 4 기기에서일상적인청취볼륨을설정합니다. 5 입력레벨을조정합니다 (12페이지). 12

31 추가정보 사용전주의사항 자동차를직사광선이내리쬐는곳에주차한경우기기를미리식힙니다. 뜨거운직사광선으로인해오작동이발생할수있으므로전면패널또는오디오장치를자동차안에두지마십시오. 전원안테나는자동으로늘어납니다. 결로현상기기안에결로현상이발생한경우기기가올바로작동되지않을수있으므로디스크를꺼내고마를때까지한시간정도기다리십시오. 높은음질수준을유지하려면기기나디스크에액체가튀지않도록주의하십시오. 디스크에관한주의 디스크를직사광선이나열통풍구와같은열원에노출시키거나직사광선이내리쬐는곳에주차한자동차내부에두지마십시오. 재생하기전에클리닝헝겊을사용하여중심에서바깥쪽으로디스크를닦아내십시오. 벤젠, 시너, 시판되는클리너등과같은용제를사용하지마시오. 본기기는콤팩트디스크 (CD) 규격에준거한디스크를재생하도록디자인되어있습니다. 듀얼디스크나저작권보호기술을사용하여인코딩된일부음악디스크의경우콤팩트디스크 (CD) 규격을준수하지않으므로본기기에서재생하지못할수있습니다. 본기기에서재생할수없는디스크 라벨, 스티커또는접착테이프나종이가부착된디스크. 이러한디스크를재생하면오작동이발생하거나디스크가손상될수있습니다. 비표준모양의디스크 ( 예 : 하트모양, 사각형, 별모양 ). 재생을시도하면기기가손상될수있습니다. 8 cm 디스크. CD-R/CD-RW 디스크에대한주의점 최대개수 : (CD-R/CD-RW 에만해당 ) 폴더 ( 앨범 ): 150( 루트폴더포함 ) 파일 ( 트랙 ) 및폴더 : 300( 폴더 / 파일에포함된문자가많은경우 300 보다작을수있음 ) 파일 / 폴더이름에표시가능한문자 : 32(Joliet)/64(Romeo) 멀티세션디스크는 CD-DA 세션으로시작될경우 CD-DA 디스크로인식되고다른세션은재생되지않습니다. 본기기에서재생할수없는디스크 기록품질이나쁜 CD-R/CD-RW. 호환되지않는기록장치로기록된 CD-R/ CD-RW. 제대로파이널라이즈되지않은 CD-R/ CD-RW. ISO9660 Level 1/Level 2, Joliet/ Romeo 또는멀티세션에준거한음악 CD 형식이나 MP3 형식으로녹음되지않은 CD-R/CD-RW. MP3/WMA 파일의재생순서 MP3/WMA 폴더 ( 앨범 ) MP3/WMA 파일 ( 트랙 ) 13

32 MP3 파일에관하여 MP3(MPEG-1 Audio Layer-3) 는음악파일압축형식표준입니다. 오디오 CD 데이터를원래크기의약 1/10 로압축합니다. ID3 태그버전 1.0, 1.1, 2.2, 2.3 및 2.4 는 MP3 에만적용됩니다. ID3 태그는 15/30 문자 (1.0 및 1.1) 또는 63/126 문자 (2.2, 2.3 및 2.4) 입니다. MP3 파일의이름을지정할때는파일이름에파일확장자 ".mp3" 를추가해야합니다. VBR(Variable Bit Rate) MP3 파일의재생또는빨리감기 / 되감기도중에는경과된재생시간이정확하게표시되지않을수있습니다. 유지관리 리모컨의리튬배터리교체하기배터리의성능이약해지면리모컨의작동범위가짧아집니다. 이경우새로운 CR2025 리튬배터리로교체하십시오. 다른배터리를사용하면화재나폭발의위험이있습니다. + 면이위로 참고 320 kbps 와같이비트전송률이높은 MP3 를재생하는경우사운드가끊어질수있습니다. WMA 파일에관하여 WMA(Windows Media Audio) 는음악파일압축형식표준입니다. 오디오 CD 데이터를원래크기의약 1/22* 로압축합니다. WMA 태그는 63 문자입니다. WMA 파일의이름을지정할때는파일이름에파일확장자 ".wma" 를추가해야합니다. VBR(Variable Bit Rate) WMA 파일의재생또는빨리감기 / 되감기도중에는경과된재생시간이정확하게표시되지않을수있습니다. * 64 kbps 에만해당 참고 다음 WMA 파일의재생은지원되지않습니다. 무손실압축파일 저작권보호파일 본사용설명서에서다루지않은기기에관한문의사항이나문제점은가까운 Sony 대리점에문의하십시오. 리튬배터리에대한주의점 리튬배터리는어린이의손이닿지않는곳에두십시오. 배터리를삼켰을경우즉시의사의진찰을받은십시오. 접촉이잘되도록하려면마른헝겊으로배터리를닦으십시오. 배터리를넣을때극성이올바른방향인지확인하십시오. 단락될수있으므로금속핀셋을사용하여배터리를집지마십시오. 커넥터닦아내기기기와전면패널사이의커넥터가깨끗하지않은경우기기가올바르게작동하지않을수있습니다. 이를방지하려면전면패널을분리하고 (5 페이지 ) 면봉으로커넥터를닦으십시오. 힘을너무세게주지마십시오. 커넥터가손상될염려가있습니다. 14

33 참고 안전을위해커넥터를닦기전에시동키를끄고시동키에서키를제거하십시오. 손이나금속장치로커넥터를직접만지지마십시오. 주요제원 튜너부문 FM 튜닝범위 : MHz(50 khz 단위 ) MHz(100 khz 단위 ) MHz(200 khz 단위 ) FM 튜닝단위 : 50 khz/100 khz/200 khz 전환가능안테나단자 : 외부안테나커넥터중간주파수 : 25 khz 사용가능한감도 : 8 dbf 선택도 : 400 khz 에서 75 db 신호대잡음비 : 80 db( 스테레오 ) 분할 : 1 khz 에서 50 db 주파수응답 : 20-15,000 Hz AM 튜닝범위 : 531-1,602 khz(9 khz 단위 ) 530-1,710 khz(10 khz 단위 ) AM 튜닝단위 : 9 khz/10 khz 전환가능안테나단자 : 외부안테나커넥터중간주파수 : 9,124.5 khz 또는 9,115.5 khz/4.5 khz (9 khz 단위 ) 9,115 khz 또는 9,125 khz/5 khz (10 khz 단위 ) 감도 : 26 μv 일반출력 : 오디오출력단자 ( 후면 / 서브전환가능 ) 전원안테나 / 전원앰프컨트롤단자 (REM OUT) 입력 : 리모컨입력단자안테나입력단자 AUX 입력잭 ( 스테레오미니잭 ) 톤조절 : 저 : 60 Hz 에서 ±10 db(xplod) 중 : 1 khz 에서 ±10 db(xplod) 고 : 10 khz 에서 ±10 db(xplod) 필요전력 : 12 V DC 자동차배터리 ( 음극접지 ) 외형치수 : 약 mm ( 가로 / 세로 / 두께 ) 장착치수 : 약 mm ( 가로 / 세로 / 두께 ) 무게 : 약 1.2 kg 부속품 : 리모컨 : RM-X201 설치및연결용부품 (1 세트 ) 상기에열거한액세서리를취급하지않는대리점도있습니다. 자세한것은대리점으로문의하여주십시오. 디자인및주요제원은사전통보없이변경될수있습니다. CD 플레이어부문신호대잡음비 : 120 db 주파수응답 : 10-20,000 Hz 워우플러터 : 측정한계치미만 전원앰프부문출력 : 스피커출력스피커임피던스 : 4-8 ohms 최대전원출력 : 52 W 4(4 ohms 에서 ) 15

34 문제해결 다음점검목록은기기에서발생할수있는문제를해결하는데도움이됩니다. 아래의점검목록을진행하기전에연결및조작절차를확인하십시오. 퓨즈사용및계기판에서기기제거에대한자세한내용은본기기와함께제공된설치 / 연결설명서를참조하십시오. 일반 기기에전원이공급되지않는다. 연결또는퓨즈를확인합니다. 기기가꺼지고디스플레이가사라진경우리모컨으로기기를조작할수없습니다. 기기를켭니다. 전원안테나가연장되지않는다. 전원안테나에릴레이박스가없습니다. 소리가나지않는다. ATT 기능이활성화되었습니다. 페이더컨트롤 "FAD" 의위치가 2-스피커시스템용으로설정되지않았습니다. 비프음이들리지않는다. 비프음이취소되었습니다 (11페이지). 옵션전원앰프가연결되었고내장앰프를사용하고있지않습니다. 메모리내용이지워졌다. 전원공급리드선또는배터리가분리되었거나올바르게연결되지않았습니다. 기기가재설정되었습니다. 메모리에다시저장하십시오. 저장된방송국과올바른시간이지워진다. 퓨즈가끊어졌다. 시동키위치를전환하면소음이발생한다. 리드선이자동차의액세서리전원커넥터에제대로연결되어있지않습니다. 재생또는수신중에데모모드가시작된다. "DEMO-ON" 이설정된상태로 5분간조작하지않으면데모모드가시작됩니다. "DEMO-OFF" 를설정합니다 (12페이지). 디스플레이가디스플레이창에서사라지거나나타나지않는다. 조광등이 "DIMMER-ON" 으로설정되었습니다 (12페이지). 를길게누르면디스플레이가사라집니다. 디스플레이가표시될때까지기기에서 를누릅니다. 커넥터가더러워졌습니다 (14페이지). 자동꺼짐기능이작동하지않는다. 기기가켜졌습니다. 자동꺼짐기능은기기를끈후활성화됩니다. 기기를끕니다. 기기가작동하는중에디스플레이가사라진다. 블랙아웃기능이설정되었습니다 (12페이지). 조작버튼이작동하지않는다. 디스크가꺼내지지않는다. 및 (BACK) 을 2초이상누릅니다. 메모리에저장된내용이지워집니다. 안전을위해운전중에는재설정조작을수행하지마십시오. 라디오수신 방송국을수신할수없다. 사운드에서소음이들린다. 연결이올바르지않습니다. REM OUT 리드선 ( 파란색 / 흰색줄무늬 ) 또는액세서리전원공급리드선 ( 빨간색 ) 을자동차안테나부스터의전원공급리드선에연결합니다 ( 자동차의뒷면 / 측면유리에라디오안테나가내장된경우에만 ). 자동차안테나의연결을확인합니다. 자동안테나가올라오지않을경우전원안테나컨트롤리드선의연결을확인합니다. 튜닝단위설정이지워졌습니다. 튜닝단위를다시설정합니다 (4페이지). 프리셋튜닝이불가능하다. 올바른주파수를메모리에저장합니다. 방송신호가너무약합니다. 16

35 자동튜닝이불가능하다. 방송신호가너무약합니다. 수동튜닝을수행합니다. 디스크가꺼내지지않는다. ( 꺼내기 ) 를누릅니다 (6페이지). RDS PTY에 " " 가표시된다. 현재방송국이 RDS 방송국이아닙니다. RDS 데이터가수신되지않았습니다. 방송국에서프로그램유형을지정하지않습니다. CD 재생 디스크를넣을수없다. 다른디스크가들어있습니다. 위아래를뒤집어넣었거나잘못된방법으로디스크를강제로넣었습니다. 디스크가재생되지않는다. 결함이있거나더러운디스크입니다. CD-R/CD-RW는오디오용으로사용할수없습니다 (13페이지). MP3/WMA 파일을재생할수없다. 디스크가 MP3/WMA 형식및버전과호환되지않습니다 (13페이지). MP3/WMA 파일이다른파일에비해재생하는데시간이오래걸린다. 다음과같은디스크는재생을시작하는데시간이많이걸립니다. 복잡한트리구조를사용하여기록된디스크. 멀티세션으로기록된디스크. 데이터를추가할수있는디스크. 디스플레이항목이스크롤되지않는다. 문자가매우많은디스크의경우스크롤되지않을수있습니다. "AUTO SCR" 이 "OFF" 로설정되었습니다. "AUTO SCR-ON" 을설정합니다 (12페이지 ). (SCRL) 을길게누릅니다. 사운드를건너뛴다. 설치가올바르지않습니다. 자동차의튼튼한부분에 45 미만의각도로기기를설치합니다. 결함이있거나더러운디스크입니다. 오류표시 / 메시지 ERROR 디스크가더러워져있거나디스크를뒤집어넣었습니다. 디스크를닦아내거나올바르게넣습니다. 공디스크를넣었습니다. 문제가있는디스크는재생할수없습니다. 다른디스크를넣습니다. ( 꺼내기 ) 를눌러디스크를꺼냅니다. FAILURE 스피커 / 앰프의연결이잘못되었습니다. 본모델의설치 / 연결설명서를참조하여연결을확인합니다. NO MUSIC 디스크에음악파일이들어있지않습니다. 본기기에음악 CD를넣습니다. NO NAME 디스크 / 앨범 / 아티스트 / 트랙이름이트랙에기록되지않았습니다. OFFSET 내부오작동이발생했을수있습니다. 연결을확인합니다. 디스플레이에오류가계속표시될경우가까운 Sony 대리점에문의합니다. PUSH EJT ( 꺼내기누름 ) 디스크를꺼낼수없다. ( 꺼내기 ) 를누릅니다 (6페이지). READ 디스크의모든트랙및앨범정보를읽는중입니다. 읽기가완료되어자동으로재생이시작될때까지기다립니다. 디스크구조에따라 1분이상걸릴수있습니다. " " 또는 " " 되감기또는빨리감기중에디스크의시작또는끝부분에도달하여더이상감을수없습니다. 17

36 " " 해당문자를기기에서표시할수없습니다. 이러한해결방법으로문제가해결되지않는경우가까운 Sony 대리점에문의하십시오. CD 재생문제로인해기기수리를받으려면문제가발생할때사용했던디스크를가져오십시오 Sony Corporation Printed in Thailand