CDX-GT615UV

Transcription

1 (1) FM/AM Compact Disc Player Operating Instructions 사용설명서 GB KR To switch the FM/AM tuning step, see page 4. To cancel the demonstration (DEMO) display, see page 4. FM/AM 튜닝단위를전환하려면 4 페이지를참조하십시오. 데모 (DEMO) 표시를취소하려면 4 페이지를참조하십시오. CDX-GT615UV

2 Be sure to install this unit in the dashboard of the car for safety. For installation and connections, see the supplied installation/connections manual. This label is located on the bottom of the chassis. Warning if your car s ignition has no ACC position Be sure to set the Auto Off function (page 21). The unit will shut off completely and automatically in the set time after the unit is turned off, which prevents battery drain. If you do not set the Auto Off function, press and hold until the display disappears each time you turn the ignition off. ZAPPIN and Quick-BrowZer are trademarks of Sony Corporation. Windows Media is either a registered trademark or trademark of Microsoft Corporation in the United States and/or other countries. This product contains technology subject to certain intellectual property rights of Microsoft. Use or distribution of this technology outside of this product is prohibited without the appropriate license(s) from Microsoft. iphone, ipod, ipod classic, ipod nano, and ipod touch are trademarks of Apple Inc., registered in the U.S. and other countries. MPEG Layer-3 audio coding technology and patents licensed from Fraunhofer IIS and Thomson. Note on the lithium battery Do not expose the battery to excessive heat such as direct sunlight, fire or the like. 2

3 Table of contents Getting Started Switching the FM/AM tuning step Canceling the DEMO mode Setting the clock Detaching the front panel Location of controls Radio Storing and receiving stations RDS CD Playing a disc USB devices Playing back a USB device ipod Playing back ipod Operating an ipod directly Passenger control Searching and playing tracks Playing tracks in various modes Searching a track by name Quick-BrowZer Searching a track by listening to track passages ZAPPIN Changing the illumination Changing the color of display and buttons Dynamic Color Illuminator Advanced color setting Sound Settings and Setup Menu Changing the sound settings Enjoying sophisticated sound functions Advanced Sound Engine Adjusting setup items Using optional equipment Auxiliary audio equipment Additional Information Precautions Maintenance Specifications Troubleshooting

4 Getting Started Switching the FM/AM tuning step The FM/AM tuning step is factory-set to the 50 khz (FM)/9 khz (AM) position. If the frequency allocation system of your country is based on 200 khz (FM)/10 khz (AM) or 100 khz (FM)/10 khz (AM) step, set the tuning step before use. This setting appears when turned off. 1 Press and hold the select button. The setup display appears. 2 Rotate the control dial until TUNER- STP appears, then press it. 3 Rotate the control dial to select from 50K/9K, 100K/10K or 200K/10K, then press it. Receivable frequency by selected frequency setup: FM 50 khz: MHz, MHz, MHz... FM 100 khz: 87.5 MHz, 87.6 MHz, 87.7 MHz... FM 200 khz: 87.5 MHz, 87.7 MHz, 87.9 MHz... AM 9 khz: 531 khz, 540 khz, 549 khz... AM 10 khz: 530 khz, 540 khz, 550 khz... Canceling the DEMO mode You can cancel the demonstration display which appears during turning off. 1 Press and hold the select button. The setup display appears. 2 Rotate the control dial until DEMO appears, then press it. 3 Rotate the control dial to select DEMO-OFF, then press it. The setting is complete. 4 Press (BACK). The display returns to normal reception/ play mode. Setting the clock The clock uses a 12-hour digital indication. 1 Press and hold the select button. The setup display appears. 2 Rotate the control dial until CLOCK- ADJ appears, then press it. The hour indication flashes. 3 Rotate the control dial to set the hour and minute. To move the digital indication, press /+. 4 After setting the minute, press the select button. The setup is complete and the clock starts. To display the clock, press. 4

5 Detaching the front panel You can detach the front panel of this unit to prevent theft. 1 Press and hold. The unit is turned off. Attaching the front panel Engage part A of the front panel with part B of the unit, as illustrated, and push the left side into position until it clicks. 2 Press the front panel release button, then pull it off towards you. Caution alarm If you turn the ignition switch to the OFF position without detaching the front panel, the caution alarm will sound for a few seconds. The alarm will only sound if the built-in amplifier is used. Note Do not subject the front panel to heat/high temperature or moisture. Avoid leaving it in a parked car or on a dashboard/rear tray. 5

6 Location of controls Main unit This section contains instructions on the location of controls and basic operations. SOURCE/OFF button Press to turn on the power/change the source (Radio/CD/USB/AUX). Press and hold for 1 second to turn off the power. Press and hold for more than 2 seconds to turn off the power and the display disappears. SEEK +/ buttons Radio: To tune in stations automatically (press); find a station manually (press and hold). CD/USB: To skip tracks (press); skip tracks continuously (press, then press again within about 1 second and hold); reverse/fast-forward a track (press and hold). ZAP button page 15 To enter ZAPPIN mode. Control dial/select button page 18, 21 To adjust volume (rotate); select setup items (press and rotate). Disc slot Insert the disc (label side up), playback starts. Display window (eject) button To eject the disc. USB connector page 11, 12 (BACK)/MODE button page 9, 13 Press to return to the previous display/ select the radio band (FM/AM). Press and hold to enter/cancel the passenger control. Front panel release button page 5 Receptor for the remote commander (BROWSE) button page 14 To enter the Quick-BrowZer mode. 6

7 PTY button page 10 To select PTY in RDS. Number buttons Radio: To receive stored stations (press); store stations (press and hold). CD/USB: / : ALBUM / (during MP3/ WMA/AAC playback) To skip albums (press); skip albums continuously (press and hold). : REP* page 14 : SHUF page 14 : PAUSE To pause playback. To cancel, press again. DSPL (display)/scrl (scroll) button page 10, 11, 12, 13 To change display items (press); scroll the display item (press and hold). AUX input jack page 22 * This button has a tactile dot. Note If the unit is turned off and the display disappears, it cannot be operated with the remote commander unless on the unit is pressed, or a disc is inserted to activate the unit first. 7

8 RM-X211 Remote commander OFF SOURCE PTY MENU SOUND ATT MODE DSPL/ SCRL PAUSE VOL Remove the insulation film before use. + ENTER 8 9 q; qa qs qd qf OFF button To turn off the power; stop the source. SOURCE button To turn on the power; change the source (Radio/CD/USB/AUX). ( )/ ( ) buttons To control Radio/CD/USB, the same as /+ on the unit. Setup, sound setting, etc., can be operated by. (BACK) button ENTER button To apply a setting. PTY button VOL (volume) +*/ button ATT (attenuate) button To attenuate the sound. To cancel, press again. MODE button Press to select the radio band (FM/AM). Press and hold to enter/cancel the passenger control. SOUND/MENU button To enter sound setting (press); enter menu (press and hold). (BROWSE) button (+)/ ( ) buttons To control CD/USB, the same as / (ALBUM / ) on the unit. Setup, sound setting, etc., can be operated by. DSPL/SCRL button Number buttons To receive stored stations (press); store stations (press and hold). To pause playback (press ). * This button has a tactile dot. 8

9 Radio Storing and receiving stations Tuning step setting is required (page 4). Notes If the tuning step setting is changed, the stored stations will be erased. If replacing the car battery or changing the connections, the tuning step setting will be erased, and you will need to set again. Caution When tuning in stations while driving, use Best Tuning Memory (BTM) to prevent an accident. Storing automatically BTM 1 Press repeatedly until TUNER appears. To change the band, press repeatedly. You can select from FM1, FM2, FM3, AM1 or AM2. Storing manually 1 While receiving the station that you want to store, press and hold a number button ( to ) until MEM appears. Receiving the stored stations 1 Select the band, then press a number button ( to ). Tuning automatically 1 Select the band, then press +/ to search for the station. Scanning stops when the unit receives a station. Repeat this procedure until the desired station is received. Tip If you know the frequency of the station you want to listen to, press and hold +/ to locate the approximate frequency, then press +/ repeatedly to fine adjust to the desired frequency (manual tuning). 2 Press and hold the select button. The setup display appears. 3 Rotate the control dial until BTM appears, then press it. The unit stores stations in order of frequency on the number buttons. 9

10 RDS FM stations with Radio Data System (RDS) service send inaudible digital information along with the regular radio program signal. Notes Depending on the country/region, not all RDS functions may be available. RDS will not work if the signal strength is too weak, or if the station you are tuned to is not transmitting RDS data. Changing display items Press. Selecting PTY (Program Types) Displays the currently received program type. Also searches your selected program type. 1 Press during FM reception. The current program type name appears if the station is transmitting PTY data. 2 Rotate the control dial until the desired program type appears, then press it. The unit starts to search for a station broadcasting the selected program type. Type of programs NEWS (News), AFFAIRS (Current Affairs), INFO (Information), SPORT (Sports), EDUCATE (Education), DRAMA (Drama), CULTURE (Culture), SCIENCE (Science), VARIED (Varied), POP M (Pop Music), ROCK M (Rock Music), EASY M (M.O.R. Music), LIGHT M (Light classical), CLASSICS (Serious classical), OTHER M (Other Music), WEATHER (Weather), FINANCE (Finance), CHILDREN (Children s program), SOCIAL A (Social Affairs), RELIGION (Religion), PHONE IN (Phone In), TRAVEL (Travel), LEISURE (Leisure), JAZZ (Jazz Music), COUNTRY (Country Music), NATION M (National Music), OLDIES (Oldies Music), FOLK M (Folk Music), DOCUMENT (Documentary) Note You may receive a different radio program from the one you select. Setting CT (Clock Time) The CT data from the RDS transmission sets the clock. 1 Set CT-ON in setup (page 21). Note The CT function may not work properly even though an RDS station is being received. 10

11 CD Playing a disc This unit can play CD-DA (also containing CD TEXT) and CD-R/CD-RW (MP3/ WMA/AAC files (page 23)). 1 Insert the disc (label side up). Playback starts automatically. To eject the disc, press. Note When ejecting/inserting a disc, keep any USB devices disconnected to avoid damage to the disc. Changing display items Displayed items may differ depending on the disc type, recording format and settings. Press. USB devices MSC (Mass Storage Class)-type USB devices compliant with the USB standard can be used. Corresponding codec is MP3 (.mp3), WMA (.wma), AAC (.m4a) and AAC (.mp4). Backup of data in a USB device is recommended. For details on the compatibility of your USB device, visit the support site on the back cover. Note Connect the USB device after starting the engine. Depending on the USB device, malfunction or damage may occur if it is connected before starting the engine. Playing back a USB device 1 Open the USB cover, then connect the USB device to the USB connector with its USB cable. Playback starts. If a USB device is already connected, to start playback, press repeatedly until USB appears. To stop playback, press and hold for 1 second. To remove the USB device, stop the USB playback, then remove the USB device. 11

12 Notes Do not use USB devices so large or heavy that they may fall down due to vibration, or cause a loose connection. Do not detach the front panel during playback of the USB device, otherwise USB data may be damaged. Changing display items Displayed items may differ depending on the USB device, recording format and settings. Press. ipod In these Operating Instructions, ipod is used as a general reference for the ipod functions on the ipod and iphone, unless otherwise specified by the text or illustrations. For details on the compatibility of your ipod, see About ipod (page 24) or visit the support site on the back cover. Notes The maximum number of displayable data is as follows. folders (albums): 128 files (tracks) per folder: 500 It may take time for playback to begin, depending on the amount of recorded data. DRM (Digital Rights Management) files may not be played. During playback or fast-forward/reverse of a VBR (Variable Bit Rate) MP3/WMA/AAC file, elapsed playing time may not display accurately. Playback of the following MP3/WMA/AAC files is not supported. lossless compression copyright-protected Playing back ipod Before connecting the ipod, turn down the volume of the unit. 1 Open the USB cover, then connect the ipod to the USB connector with the USB connection cable for ipod (not supplied)*. * Using the RC-100IP USB connection cable for ipod is recommended. The tracks on the ipod start playing automatically from the point last played. 12 If an ipod is already connected, to start playback press repeatedly until USB appears. ( IPD appears in the display when ipod is recognized.) Press and hold for 1 second to stop playback. To remove the ipod, stop the ipod playback, then remove the ipod.

13 Caution for iphone When you connect an iphone via USB, telephone volume is controlled by iphone itself. In order to avoid sudden loud sound after a call, do not increase the volume on the unit during a telephone call. Note Do not detach the front panel during playback of the ipod, otherwise data may be damaged. Tip ipod is recharged while the unit is turned on. Resuming mode When the ipod is connected to the dock connector, playback starts in the mode set by the ipod. In this mode, the following buttons do not function. (REP) (SHUF) Operating an ipod directly Passenger control You can operate an ipod directly even when connected to the dock connecter. 1 During playback, press and hold. MODE IPOD appears and you will be able to operate the ipod directly. To exit the passenger control, press and hold. Then MODE AUDIO will appear and the play mode will change to ipod mode. Note The volume can be adjusted only by the unit. Changing display items Press. Note Some letters stored in ipod may not be displayed correctly. Skipping albums, podcasts, genres, playlists and artists To Do this Skip Press / (ALBUM / ) [press once for each] Skip continuously Press and hold / (ALBUM / ) [hold to desired point] 13

14 14 Searching and playing tracks Playing tracks in various modes You can listen to tracks repeatedly (repeat play) or in random order (shuffle play). Available play modes differ depending on the selected sound source. 1 During playback, press (REP) or (SHUF) repeatedly until the desired play mode appears. Playback in selected play mode may take time to start. Repeat play Select TRACK ALBUM PODCAST* 1 ARTIST* 1 PLAYLIST* 1 GENRE* 1 OFF Shuffle play Select SHUF ALBUM To play track repeatedly. album repeatedly. podcast repeatedly. artist repeatedly. playlist repeatedly. genre repeatedly. track in normal order (Normal play). To play album in random order. SHUF DISC* 2 disc in random order. SHUF PODCAST* 1 podcast in random order. SHUF ARTIST* 1 artist in random order. SHUF PLAYLIST* 1 playlist in random order. SHUF GENRE* 1 SHUF DEVICE* 3 SHUF OFF *1 ipod only *2 CD only *3 USB and ipod only genre in random order. device in random order. track in normal order (Normal play). Searching a track by name Quick-BrowZer You can search for a track in a CD or USB device easily by category. 1 Press (BROWSE)*. The unit enters the Quick-BrowZer mode, and the list of search categories appears. When the track list appears, press (BACK) repeatedly until the desired search category appears. * During playback, press (BROWSE) for more than 2 seconds to directly return to the beginning of the category list (USB only). 2 Rotate the control dial to select the desired search category, then press it to confirm. 3 Repeat step 2 until the desired track is selected. Playback starts. To exit the Quick-BrowZer mode, press (BROWSE). Note When entering the Quick-BrowZer mode, the repeat/shuffle setting is canceled.

15 Searching by skip items Jump mode When many items are in a category, you can search the desired item quickly. 1 Press + in Quick-BrowZer mode. The item name will appear. 2 Rotate the control dial to select the item near the one desired. It skips in steps of 10% of the total item number. 3 Press the select button. The display returns to the Quick- BrowZer mode and the selected item appears. 4 Rotate the control dial to select the desired item and press it. Playback starts if the selected item is a track. To cancel Jump mode, press (BACK) or. Searching by alphabetical order Alphabet search When an ipod is connected to the unit, you can search for a desired item alphabetically. 1 Press + in Quick-BrowZer mode. 2 Rotate the control dial to select the first letter of the desired item, then press it. A list of items beginning with the selected letter appears in alphabetical order. 3 Rotate the control dial to select the desired item, then press it. Playback starts if the selected item is a track. To cancel Alphabet search, press (BACK) or. Notes In Alphabet search, a symbol or article (a/an/ the) before the selected letter of the item is excluded. Depending on the search item you select, only Jump mode may be available. Alphabet search may take some time, depending on the amount of tracks. Searching a track by listening to track passages ZAPPIN While playing back short track passages in a CD or USB device in sequence, you can search for a track you want to listen to. ZAPPIN mode is suitable for searching for a track in shuffle or shuffle repeat mode. 1 Press during playback. Playback starts from a passage of the next track. You can select the playback time (page 22). Track pressed. The part of each track to play back in ZAPPIN mode. 2 Press the select button or when a track you want to listen is played back. The track that you select returns to normal play mode from the beginning. Pressing (BACK) also confirms a track to playback. Tips Press +/ in ZAPPIN mode to skip a track. Press / (ALBUM / ) in ZAPPIN mode to skip album. 15

16 Changing the illumination Changing the color of display and buttons Dynamic Color Illuminator Dynamic Color Illuminator allows you to change the color of the display and buttons on the main unit to match the car s interior. You can select from 12 preset colors, customized color and 5 preset patterns. Preset colors: RED, AMBER, M_AMBER, YELLOW, WHITE, LIGHT GREEN, GREEN, LIGHT BLUE, SKY BLUE, BLUE, PURPLE, PINK. Preset patterns: RAINBOW, OCEAN, SUNSET, FOREST, RANDOM. 1 Press and hold the select button. The setup display appears. 2 Rotate the control dial until COLOR appears, then press it. 3 Rotate the control dial to select the desired preset color, then press it. 4 Press (BACK). Note If the control dial is rotated rapidly, the color of the display and the buttons may change too quickly. Customizing the display and button color Custom Color You can register a customized color for the display and buttons. 1 Press and hold the select button. The setup display appears. 2 Rotate the control dial until CUSTOM-C appears, then press it. 3 Rotate the control dial until BASE appears, then press it. You can select a preset color as a basis for further customizing. When you select BASE, customized color is overwritten. 4 Rotate the control dial to select from RGB RED, RGB GRN, or RGB BLUE, then press it. 5 Rotate the control dial to adjust the color range, then press it. Adjustable color range: You cannot set 0 for all color ranges. 6 Press (BACK). Changing DAY/NIGHT color mode You can set a different color for DAY/ NIGHT depending on the DIMMER setting. Color mode DIMMER* 1 DAY NIGHT OFF or AUTO (turn off the head light* 2 ) ON or AUTO (turn on the head light* 2 ) 16 *1 For details on the DIMMER, see page 21. *2 Available only when the illumination control lead is connected. 1 Select DAYNIGHT in step 2. 2 Select DAY or NIGHT. 3 Customize the preset channel from step 2 to 5.

17 Advanced color setting Changing the color with sound synchronization Sound Synchronization When you select a preset pattern, sound synchronization becomes effective. 1 Press and hold the select button. The setup display appears. 2 Rotate the control dial until SND SYNC appears, then press it. 3 Rotate the control dial to select SYNC-ON, then press it. 4 Press (BACK). Start up effect Start White When you push on, the color of display and the buttons on the main unit turns white once, and then the color changes to the customized color. 1 Press and hold the select button. The setup display appears. 2 Rotate the control dial until START- WHT appears, then press it. 3 Rotate the control dial to select WHITE-ON, then press it. 4 Press (BACK). To cancel Start White, select OFF on step 3. Displaying clear color White Menu You can display the menu more clearly (White) without concern for color setting. 1 Press and hold the select button. The setup display appears. 2 Rotate the control dial until WHT MENU appears, then press it. 3 Rotate the control dial to select WHITE-ON, then press it. 4 Press (BACK). To cancel White Menu, select OFF on step 3. 17

18 18 Sound Settings and Setup Menu Changing the sound settings Adjusting the sound characteristics 1 During reception/playback, press the select button. 2 Rotate the control dial until the desired menu item appears, then press it. 3 Rotate the control dial to select the setting, then press it. 4 Press (BACK). The following items can be set: EQ7 PRESET (page 18) EQ7 SETTING (page 19) POSITION SET POSITION (Listening Position setting) (page 19) ADJ POSITION* 1 (Listening Position adjustment) (page 20) SET SW POS* 1 * 2 (Subwoofer Position setting) (page 19) BALANCE Adjusts the sound balance: RIGHT-15 CENTER LEFT-15. FADER Adjusts the relative level: FRONT-15 CENTER REAR-15. DM+ (page 20) RB ENH (Rear Bass Enhancer) (page 20) SW LEVEL* 2 (Subwoofer Level) Adjusts the subwoofer volume level: +10 db 0 db 10 db. ( ATT is displayed at the lowest setting.) AUX VOL* 3 (AUX Volume level) Adjusts the volume level for each connected auxiliary equipment: +18 db 0 db 8 db. This setting negates the need to adjust the volume level between sources. *1 Hidden when SET POSITION is set to OFF. *2 When the audio output is set to SUB-OUT (page 21). *3 When AUX source is activated (page 22). Enjoying sophisticated sound functions Advanced Sound Engine Advanced Sound Engine creates an ideal incar sound field with digital signal processing. Selecting the sound quality EQ7 Preset You can select an equalizer curve from 7 equalizer curves (XPLOD, VOCAL, EDGE, CRUISE, SPACE, GRAVITY, CUSTOM or OFF). 1 During reception/playback, press the select button. 2 Rotate the control dial until EQ7 PRESET appears, then press it. 3 Rotate the control dial until the desired equalizer curve appears, then press it. 4 Press (BACK). To cancel the equalizer curve, select OFF in step 3.

19 Tip The equalizer curve setting can be memorized for each source. Customizing the equalizer curve EQ7 Setting CUSTOM of EQ7 allows you to make your own equalizer settings. 1 Select a source, then press the select button. 2 Rotate the control dial until EQ7 SETTING appears, then press it. 3 Rotate the control dial until BASE appears, then press it. You can select an equalizer curve as a basis for further customizing. 4 Rotate the control dial to select the equalizer curve, then press it. 5 Setting the equalizer curve. Rotate the control dial to select the frequency range, then press it. BAND1: 63 Hz BAND2: 160 Hz BAND3: 400 Hz BAND4: 1 khz BAND5: 2.5 khz BAND6: 6.3 khz BAND7: 16.0 khz Rotate the control dial to adjust the volume level, then press it. The volume level is adjustable in 1 db steps, from -6 db to +6 db. Repeat steps and to adjust other frequency ranges. Optimizing sound by Time Alignment Listening Position The unit can simulate a natural sound field by delaying the sound output from each speaker to suit your position. The options for POSITION are indicated below. FRONT L ( ): Front left FRONT R ( ): Front right FRONT ( ): Center front ALL ( ): In the center of your car OFF: No position set You can also set the approximate subwoofer position from your listening position if: the audio output is set to SUB-OUT (page 21). the listening position is set besides OFF. The options for SET SW POS are indicated below. NEAR ( ): Near NORMAL ( ): Normal FAR ( ): Far 1 During reception/playback, press the select button. 2 Rotate the control dial until SET POSITION appears, then press it. 3 Rotate the control dial to select from FRONT L, FRONT R, FRONT or ALL, then press it. 4 Rotate the control dial until SET SW POS appears, then press it. 6 Press (BACK) twice. The equalizer curve is stored in CUSTOM. 19

20 5 Rotate the control dial to select the subwoofer position from NEAR, NORMAL or FAR, then press it. 6 Press (BACK). To cancel listening position, select OFF on step 3. Adjusting the listening position You can fine-tune the listening position setting. 1 During reception/playback, press the select button. 2 Rotate the control dial until ADJ POSITION appears, then press it. Using rear speakers as subwoofer Rear Bass Enhancer Rear Bass Enhancer enhances the bass sound by applying the low pass filter setting (page 22) to the rear speakers. This function allows the rear speakers to work as a subwoofer if one is not connected. 1 During reception/playback, press the select button. 2 Rotate the control dial until RB ENH appears, then press it. 3 Rotate the control dial to select from 1, 2 or 3, then press it. 4 Press (BACK). 3 Rotate the control dial to adjust the listening position, then press it. Adjustable range: +3 CENTER 3. 4 Press (BACK). DM+ Advanced DM+ Advanced improves digitally compressed sound by restoring high frequencies lost in the compression process. 1 During playback, press the select button. 2 Rotate the control dial until DM+ appears, then press it. 3 Rotate the control dial to select ON, then press it. 4 Press (BACK). Tip The DM+ setting can be memorized for each source. 20

21 Adjusting setup items 1 Press and hold the select button. The setup display appears. 2 Rotate the control dial until the desired item appears, then press it. 3 Rotate the control dial to select the setting, then press it.* The setting is complete. 4 Press (BACK). * For CLOCK-ADJ, TUNER-STP and BTM settings, step 4 is not necessary. The following items can be set depending on the source and setting: CLOCK-ADJ (Clock Adjust) (page 4) TUNER-STP* 1 (Tuner Step) (page 4) CT (Clock Time) Activates the CT function: ON, OFF (page 10). BEEP Activates the beep sound: ON, OFF. CAUT ALM* 1 (Caution Alarm) Activates the caution alarm: ON, OFF (page 5). AUX-A* 1 (AUX Audio) Activates the AUX source display: ON, OFF (page 22). AUTO OFF Shuts off automatically after a desired time when the unit is turned off: NO, 30S (Seconds), 30M (Minutes), 60M (Minutes). REAR/SUB* 1 Switches the audio output: SUB-OUT (subwoofer), REAR-OUT (power amplifier). BLK OUT (Black Out) Turns off the illumination automatically for any source (e.g., during radio reception/cd playback, etc.) if no operation is performed for 5 seconds: ON, OFF. To bring the light back on, press any button on the unit. DEMO (Demonstration) Activates the demonstration: ON, OFF. DIMMER Changes the display brightness. AT : to dim the display automatically when you turn lights on. (Available only when the illumination control lead is connected.) ON : to dim the display. OFF : deactivate the dimmer. COLOR (Preset Color) Selects the preset color of the display and buttons on the main unit (page 16). CUSTOM-C (Custom Color) Selects a preset color as a basis for further customizing (page 16). SND SYNC Selects the color with sound synchronization: ON, OFF. WHT MENU Sets the effect when the source is switched: ON, OFF. START-WHT Sets the start up color: ON, OFF. M.DISPLAY (Motion Display) SA : to show moving patterns and spectrum analyzer. OFF : to deactivate the Motion Display. AUTO SCR (Auto Scroll) Scrolls long items automatically: ON, OFF. 21

22 ZAP TIME (Zappin Time) Selects the playback time for the ZAPPIN function. Z.TIME-1 (about 6 seconds), Z.TIME-2 (about 15 seconds), Z.TIME-3 (about 30 seconds). ZAP BEEP (Zappin Beep) Has the beep sound between track passages: ON, OFF. LPF FREQ* 2 (Low Pass Filter Frequency) Selects the subwoofer cut-off frequency: 50Hz, 60Hz, 80Hz, 100Hz, 120Hz. LPF SLOP* 2 (Low Pass Filter Slope) Selects the LPF slope: 1, 2, 3. SW PHASE* 3 (Subwoofer Phase) Selects the subwoofer phase: NORM, REV. HPF FREQ (High Pass Filter Frequency) Selects the front/rear speaker cut-off frequency: OFF, 50Hz, 60Hz, 80Hz, 100Hz, 120Hz. Using optional equipment Auxiliary audio equipment By connecting an optional portable audio device to the AUX input jack (stereo mini jack) on the unit and then simply selecting the source, you can listen on your car speakers. Connecting the portable audio device 1 Turn off the portable audio device. 2 Turn down the volume on the unit. 3 Connect the portable audio device to the unit with a connecting cord (not supplied)*. * Be sure to use a straight type plug. 22 HPF SLOP (High Pass Filter Slope) Selects the HPF slope (effective only when HPF FREQ is set to other than OFF ): 1, 2, 3. LOUDNESS (Dynamic Loudness) Reinforces bass and treble for clear sound at low volume levels: ON, OFF. ALO (Automatic Level Optimizer) Adjust the playback volume level of all playback sources to the optimum level: ON, OFF. BTM (page 9) *1 When the unit is turned off. *2 When the audio output is set to SUB-OUT or Rear Bass Enhancer is set to other than OFF. *3 When the audio output is set to SUB-OUT. Adjusting the volume level Be sure to adjust the volume for each connected audio device before playback. 1 Turn down the volume on the unit. 2 Press repeatedly until AUX appears. 3 Start playback of the portable audio device at a moderate volume. 4 Set your usual listening volume on the unit. 5 Adjust the input level (page 18).

23 Additional Information Precautions Cool off the unit beforehand if your car has been parked in direct sunlight. Do not leave the front panel or audio devices brought in inside the car, or it may cause malfunction due to high temperature in direct sunlight. Power antenna (aerial) extends automatically. Moisture condensation Should moisture condensation occur inside the unit, remove the disc and wait for about an hour for it to dry out; otherwise the unit will not operate properly. To maintain high sound quality Do not splash liquid onto the unit or discs. Notes on discs Do not expose discs to direct sunlight or heat sources such as hot air ducts, nor leave it in a car parked in direct sunlight. Before playing, wipe the discs with a cleaning cloth from the center out. Do not use solvents such as benzine, thinner, commercially available cleaners. This unit is designed to play back discs that conform to the Compact Disc (CD) standard. DualDiscs and some of the music discs encoded with copyright protection technologies do not conform to the Compact Disc (CD) standard, therefore, these discs may not be playable by this unit. Discs that this unit CANNOT play Discs with labels, stickers, or sticky tape or paper attached. Doing so may cause a malfunction, or may ruin the disc. Discs with non-standard shapes (e.g., heart, square, star). Attempting to do so may damage the unit. 8 cm (3 1 /4 in) discs. Notes on CD-R/CD-RW discs The maximum number of: (CD-R/CD-RW only) folders (albums): 150 (including root folder) files (tracks) and folders: 300 (may less than 300 if folder/file names contain many characters) displayable characters for a folder/file name: 32 (Joliet)/64 (Romeo) If the multi-session disc begins with a CD- DA session, it is recognized as a CD-DA disc, and other sessions are not played back. Discs that this unit CANNOT play CD-R/CD-RW of poor recording quality. CD-R/CD-RW recorded with an incompatible recording device. CD-R/CD-RW which is finalized incorrectly. CD-R/CD-RW other than those recorded in music CD format or MP3 format conforming to ISO9660 Level 1/Level 2, Joliet/Romeo or multi-session. Playback order of MP3/WMA/ AAC files MP3/WMA/AAC Folder (album) MP3/WMA/ AAC file (track) 23

24 About ipod You can connect to the following ipod models. Update your ipod devices to the latest software before use. Made for ipod touch (4th generation) ipod touch (3rd generation) ipod touch (2nd generation) ipod touch (1st generation) ipod classic ipod with video* ipod nano (6th generation) ipod nano (5th generation) ipod nano (4th generation) ipod nano (3rd generation) ipod nano (2nd generation) ipod nano (1st generation)* iphone 4 iphone 3GS iphone 3G iphone * Passenger control is not available for ipod nano (1st generation) or ipod with video. Made for ipod, and Made for iphone mean that an electronic accessory has been designed to connect specifically to ipod or iphone, respectively, and has been certified by the developer to meet Apple performance standards. Apple is not responsible for the operation of this device or its compliance with safety and regulatory standards. Please note that the use of this accessory with ipod or iphone may affect wireless performance. If you have any questions or problems concerning your unit that are not covered in this manual, consult your nearest Sony dealer. Maintenance Replacing the lithium battery of the remote commander When the battery becomes weak, the range of the remote commander becomes shorter. Replace the battery with a new CR2025 lithium battery. Use of any other battery may present a risk of fire or explosion. 1 2 c + side up Notes on the lithium battery Keep the lithium battery out of the reach of children. Should the battery be swallowed, immediately consult a doctor. Wipe the battery with a dry cloth to assure a good contact. Be sure to observe the correct polarity when installing the battery. Do not hold the battery with metallic tweezers, otherwise a short-circuit may occur. WARNING Battery may explode if mistreated. Do not recharge, disassemble, or dispose of in fire. Cleaning the connectors The unit may not function properly if the connectors between the unit and the front panel are not clean. In order to prevent this, detach the front panel (page 5) and clean the connectors with a cotton swab. Do not apply too much force. Otherwise, the connectors may be damaged. 24

25 Notes For safety, turn off the ignition before cleaning the connectors, and remove the key from the ignition switch. Never touch the connectors directly with your fingers or with any metal device. Specifications Tuner section FM Tuning range: MHz (at 50 khz step) MHz (at 100 khz step) MHz (at 200 khz step) FM tuning step: 50 khz/100 khz/200 khz switchable Antenna (aerial) terminal: External antenna (aerial) connector Intermediate frequency: 25 khz Usable sensitivity: 8 dbf Selectivity: 75 db at 400 khz Signal-to-noise ratio: 80 db (stereo) Separation: 50 db at 1 khz Frequency response: 20 15,000 Hz AM Tuning range: 531 1,602 khz (at 9 khz step) 530 1,710 khz (at 10 khz step) AM tuning step: 9 khz/10 khz switchable Antenna (aerial) terminal: External antenna (aerial) connector Intermediate frequency: 9,124.5 khz or 9,115.5 khz/4.5 khz (at 9 khz step) 9,115 khz or 9,125 khz/5 khz (at 10 khz step) Sensitivity: 26 μv Power amplifier section Output: Speaker outputs Speaker impedance: 4 8 ohms Maximum power output: 52 W 4 (at 4 ohms) General Outputs: Audio outputs terminal (front, rear/sub switchable) Power antenna (aerial)/power amplifier control terminal (REM OUT) Inputs: Remote controller input terminal Antenna (aerial) input terminal AUX input jack (stereo mini jack) USB signal input connector Power requirements: 12 V DC car battery (negative ground (earth)) Dimensions: Approx mm (7 1 / /8 in) (w/h/d) Mounting dimensions: Approx mm (7 1 /4 2 1 /8 6 1 /2 in) (w/h/d) Mass: Approx. 1.2 kg (2 lb 11 oz) Supplied accessories: Remote commander: RM-X211 Parts for installation and connections (1 set) Optional accessory/equipment: USB connection cable for ipod: RC-100IP Your dealer may not handle some of the above listed accessories. Please ask the dealer for detailed information. Design and specifications are subject to change without notice. CD Player section Signal-to-noise ratio: 120 db Frequency response: 10 20,000 Hz Wow and flutter: Below measurable limit USB Player section Interface: USB (Full-speed) Maximum current: 1 A 25

26 26 Troubleshooting The following checklist will help you remedy problems you may encounter with your unit. Before going through the checklist below, check the connection and operating procedures. For details on using the fuse and removing the unit from the dashboard, refer to the installation/connections manual supplied with this unit. If the problem is not solved, visit the support site on the back cover. General No power is being supplied to the unit. Check the connection or fuse. If the unit is turned off and the display disappears, it cannot be operated with the remote commander. Turn on the unit. The power antenna (aerial) does not extend. The power antenna (aerial) does not have a relay box. No sound. The ATT function is activated. The position of the fader control FADER is not set for a 2-speaker system. No beep sound. The beep sound is canceled (page 21). An optional power amplifier is connected and you are not using the built-in amplifier. The contents of the memory have been erased. The power supply lead or battery has been disconnected or it is not connected properly. Stored stations and correct time are erased. The fuse has blown. Makes noise when the position of the ignition is switched. The leads are not matched correctly with the car s accessory power connector. During playback or reception, demonstration mode starts. If no operation is performed for 5 minutes with DEMO-ON set, demonstration mode starts. Set DEMO-OFF (page 21). The display disappears from/does not appear in the display window. The dimmer is set to DIM-ON (page 21). The display disappears if you press and hold. Press on the unit until the display appears. The connectors are dirty (page 24). The Auto Off function does not operate. The unit is turned on. The Auto Off function activates after turning off the unit. Turn off the unit. The display disappears while the unit is operating. The Black Out function is set to on (page 21). Radio reception The stations cannot be received. The sound is hampered by noises. The connection is not correct. Connect a power antenna (aerial) control lead (blue/white striped) or accessory power supply lead (red) to the power supply lead of a car s antenna (aerial) booster (only when your car has built-in radio antenna (aerial) in the rear/side glass). Check the connection of the car antenna (aerial). If the auto antenna (aerial) will not go up, check the connection of the power antenna (aerial) control lead. The tuning step setting has been erased. Set the tuning step again (page 4). Preset tuning is not possible. Store the correct frequency in the memory. The broadcast signal is too weak. Automatic tuning is not possible. The broadcast signal is too weak. Perform manual tuning.

27 RDS PTY displays The current station is not an RDS station. RDS data has not been received. The station does not specify the program type. CD playback The disc cannot be loaded. Another disc is already loaded. The disc has been forcibly inserted upside down or in the wrong way. The disc does not play back. Defective or dirty disc. The CD-Rs/CD-RWs are not for audio use (page 23). USB playback You cannot play back items via a USB hub. This unit cannot recognize USB devices via a USB hub. Cannot play back items. A USB device does not work. Reconnect it. The USB device takes longer to play back. The USB device contains files with a complicated tree structure. The sound is intermittent. The sound may be intermittent at a high-bitrate of more than 320 kbps. MP3/WMA/AAC files cannot be played back. The disc is incompatible with the MP3/WMA/ AAC format and version. For details on playable discs and formats, visit the support site. MP3/WMA/AAC files take longer to play back than others. The following discs take a longer time to start playback. a disc recorded with a complicated tree structure. a disc recorded in Multi Session. a disc to which data can be added. The display items do not scroll. For discs with very many characters, those may not scroll. AUTO SCR is set to OFF. Set A.SCRL-ON (page21). Press and hold (SCRL). The sound skips. Installation is not correct. Install the unit at an angle of less than 45 in a sturdy part of the car. Defective or dirty disc. 27

28 Error displays/messages CHECKING The unit is confirming the connection of a USB device. Wait until confirming the connection is finished. ERROR The disc is dirty or inserted upside down. Clean or insert the disc correctly. A blank disc has been inserted. The disc cannot play due to a problem. Insert another disc. USB device was not automatically recognized. Reconnect it again. Press to remove the disc. FAILURE The connection of speakers/amplifiers is incorrect. See the installation/connections manual of this model to check the connection. HUB NO SUPRT (Hubs Not Supported) USB hub is not supported on this unit. NO DEV (No Device) USB is selected as source without a USB device connected. A USB device or a USB cable has been disconnected during playback. Be sure to connect a USB device and USB cable. NO MUSIC The disc or USB device does not contain a music file. Insert a music CD in this unit. Connect a USB device with a music file in it. OFFSET There may be an internal malfunction. Check the connection. If the error indication remains on in the display, consult your nearest Sony dealer. OVERLOAD USB device is overloaded. Disconnect the USB device, then change the source by pressing. Indicates that the USB device is out of order, or an unsupported device is connected. READ The unit is reading all track and album information on the disc. Wait until reading is complete and playback starts automatically. Depending on the disc structure, it may take more than a minute. USB NO SUPRT (USB Not Supported) The connected USB device is not supported. For details on the compatibility of your USB device, visit the support site. or During reverse or fast-forward, you have reached the beginning or the end of the disc and you cannot go any further. The character cannot be displayed with the unit. If these solutions do not help improve the situation, consult your nearest Sony dealer. If you take the unit to be repaired because of CD playback trouble, bring the disc that was used at the time the problem began. NO NAME A disc/album/artist/track name is not written in the track. NOT FOUND There is no item beginning with the selected letter in Alphabet search. 28

29

30 2 자동차시동키에 ACC 위치가없을경우의경고자동꺼짐기능을설정하십시오 (21 페이지 ). 기기가꺼지고설정된시간이지나면자동으로완전히종료되므로배터리소모가방지됩니다. 자동꺼짐기능을설정하지않은경우시동키를끌때마다디스플레이가사라질때까지 를누르고계십시오.

31 목차 시작하기 FM/AM 튜닝단위전환하기 DEMO 모드취소하기 시계설정하기 전면패널분리하기 컨트롤위치 라디오 방송국저장및수신하기 RDS CD 디스크재생하기 USB 장치 USB 장치재생하기 ipod ipod 재생하기 ipod 직접조작하기 패신저컨트롤 트랙검색및재생하기 다양한모드로트랙재생하기 이름으로트랙검색하기 Quick-BrowZer 트랙구절을청취하여트랙검색하기 ZAPPIN 조명변경하기 디스플레이및버튼색상변경하기 Dynamic Color Illuminator 고급색상설정 사운드설정및설정메뉴 사운드설정변경하기 정교한사운드기능즐기기 고급사운드엔진 설정항목조정하기 옵션장비사용하기 보조오디오장비 추가정보 사용전주의사항 유지관리 주요제원 문제해결

32 시작하기 FM/AM 튜닝단위전환하기 FM/AM 튜닝단위는출하시 50 khz(fm)/9 khz(am) 로설정되어있습니다. 해당국가의주파수할당방식이 200 khz(fm)/10 khz(am) 또는 100 khz(fm)/10 khz(am) 단위에기반을두는경우사용전에튜닝단위를설정하십시오. 이설정은전원이꺼진경우표시됩니다. 1 선택버튼을길게누릅니다. 설정화면이나타납니다. 2 "TUNER-STP" 가나타날때까지컨트롤다이얼을돌린다음누릅니다. 3 컨트롤다이얼을돌려 "50K/9K", "100K/10K" 또는 "200K/10K" 를선택한다음누릅니다. 선택한주파수설정별수신가능주파수 : FM 50 khz: MHz, MHz, MHz... FM 100 khz: 87.5 MHz, 87.6 MHz, 87.7 MHz... FM 200 khz: 87.5 MHz, 87.7 MHz, 87.9 MHz... AM 9 khz: 531 khz, 540 khz, 549 khz... AM 10 khz: 530 khz, 540 khz, 550 khz... DEMO 모드취소하기 전원이꺼질때표시되는데모를취소할수있습니다. 1 선택버튼을길게누릅니다. 설정화면이나타납니다. 2 "DEMO" 가나타날때까지컨트롤다이얼을돌린다음누릅니다. 3 컨트롤다이얼을돌려 "DEMO-OFF" 를선택한다음누릅니다. 설정이완료되었습니다. 4 (BACK) 을누릅니다. 디스플레이가일반수신 / 재생모드로돌아갑니다. 시계설정하기 시계에는 12시간디지털표기가사용됩니다. 1 선택버튼을길게누릅니다. 설정화면이나타납니다. 2 "CLOCK-ADJ" 가나타날때까지컨트롤다이얼을돌린다음누릅니다. 시간표시가깜박입니다. 3 컨트롤다이얼을돌려시간과분을설정합니다. 디지털표시를이동하려면 -/+ 를누릅니다. 4 분을설정한후선택버튼을누릅니다. 설정이완료되었으며시계가시작됩니다. 시계를표시하려면 을누릅니다. 4

33 전면패널분리하기 도난방지를위해본기기의전면패널을분리할수있습니다. 1 을길게누릅니다. 기기가꺼집니다. 전면패널부착하기 그림과같이전면패널의 A 부위를기기의 B 부위에결합하여찰칵소리가날때까지왼쪽을누릅니다. 2 전면패널해제버튼 를누른다음앞으로당겨떼어냅니다. 경고성알람전면패널을분리하지않고시동키를 OFF 쪽에놓을경우경고성알람이몇초간울립니다. 알람은내장앰프가사용된경우에만울립니다. 참고 전면패널을고온다습한곳에두지마십시오. 주차한차량에그대로두거나계기판이나뒷좌석트렁크위에놓지마십시오. 5

34 컨트롤위치 본체 6 이단원에서는컨트롤위치와기본조작에대한지침이제공됩니다. SOURCE/OFF 버튼전원을켜거나소스 ( 라디오 /CD/USB/ AUX) 를변경하려면누릅니다. 전원을끄려면 1초간길게누릅니다. 전원을끄고디스플레이를사라지게하려면 2초이상길게누릅니다. SEEK +/- 버튼라디오 : 방송국을자동튜닝하거나 ( 누르기 ), 방송국을수동으로찾습니다 ( 길게누르기 ). CD/USB: 트랙을건너뛰거나 ( 누르기 ), 트랙을연속건너뛰거나 ( 누른다음약 1초내에다시길게누르기 ), 트랙되감기 / 빨리감기를합니다 ( 길게누르기 ). ZAP 버튼 15페이지 ZAPPIN 모드로들어갑니다. 컨트롤다이얼 / 선택버튼 18, 21페이지볼륨을조정하거나 ( 돌리기 ), 설정항목을선택합니다 ( 눌러서돌리기 ). 디스크슬롯디스크를넣으면 ( 라벨면이윗면 ) 재생이시작됩니다. 디스플레이창 ( 꺼내기 ) 버튼디스크를꺼냅니다. USB 커넥터 11, 12페이지 (BACK)/MODE 버튼 9, 13페이지이전디스플레이로돌아가거나오디오대역 (FM/AM) 을선택하려면누릅니다. 패신저컨트롤에들어가거나취소하려면길게누릅니다. 전면패널해제버튼 5페이지 리모컨수신부 (BROWSE) 버튼 14 페이지 Quick-BrowZer 모드로들어갑니다.

35 PTY 버튼 10페이지 RDS에서 PTY를선택합니다. 숫자버튼라디오 : 저장된방송국을수신하거나 ( 누르기 ), 방송국을저장합니다 ( 길게누르기 ). CD/USB: / : ALBUM / (MP3/ WMA/AAC 재생도중 ) 앨범을건너뛰거나 ( 누르기 ), 앨범을연속으로건너뜁니다 ( 길게누르기 ). : REP* 14페이지 : SHUF 14페이지 : PAUSE 재생을일시정지합니다. 취소하려면다시누릅니다. DSPL( 디스플레이 )/SCRL( 스크롤 ) 버튼 10, 11, 12, 13페이지디스플레이항목을변경하거나 ( 누르기 ), 디스플레이항목을스크롤합니다 ( 길게누르기 ). AUX 입력잭 22페이지 * 이버튼에는돌기가있습니다. 참고 기기가꺼지고디스플레이가사라진경우기기에서 를누르거나디스크를넣어기기를활성화한후에만리모컨으로조작할수있습니다. 7

36 RM-X211 리모컨 OFF SOURCE PTY MENU SOUND ATT MODE DSPL/ SCRL PAUSE VOL 사용전에절연필름을제거하십시오. + ENTER 8 9 q; qa qs qd qf OFF 버튼전원을끄거나, 소스를중지합니다. SOURCE 버튼전원을켜거나, 소스를변경합니다 ( 라디오 /CD/USB/AUX). ( )/ ( ) 버튼라디오 /CD/USB를제어합니다. 기기의 -/+ 와동일합니다. 설정, 사운드설정등은 을사용하여조작할수있습니다. (BACK) 버튼 ENTER 버튼설정을적용합니다. PTY 버튼 VOL( 볼륨 ) +*/- 버튼 ATT( 약화 ) 버튼사운드를약화시킵니다. 취소하려면다시누릅니다. MODE 버튼라디오대역 (FM/AM) 을선택하려면누릅니다. 패신저컨트롤에들어가거나취소하려면길게누릅니다. SOUND/MENU 버튼사운드설정을입력하거나 ( 누르기 ), 메뉴로들어갑니다 ( 길게누르기 ). (BROWSE) 버튼 (+)/ (-) 버튼 CD/USB를제어합니다. 기기의 / (ALBUM / ) 와동일합니다. 설정, 사운드설정등은 을사용하여조작할수있습니다. DSPL/SCRL 버튼 숫자버튼저장된방송국을수신하거나 ( 누르기 ), 방송국을저장합니다 ( 길게누르기 ). 재생을일시정지합니다 ( 누르기 ). * 이버튼에는돌기가있습니다. 8

37 라디오 방송국저장및수신하기 튜닝단위를설정해야합니다 (4 페이지 ). 참고 튜닝단위설정이변경된경우저장된방송국이지워집니다. 자동차배터리를교체하거나연결을변경한경우튜닝단위설정이지워지므로다시설정해야합니다. 주의운전중에방송국을튜닝할때는사고를방지하기위해 BTM(Best Tuning Memory) 을사용하십시오. 자동으로저장하기 - BTM 1 "TUNER" 가나타날때까지 를반복해서누릅니다. 대역을변경하려면 를반복해서누릅니다. FM1, FM2, FM3, AM1 또는 AM2 를선택할수있습니다. 수동으로저장하기 1 저장할방송국이수신되는상태에서 "MEM" 이나타날때까지숫자버튼 ( - ) 을길게누릅니다. 저장된방송국수신하기 1 대역을선택하고숫자버튼 ( - ) 을누릅니다. 자동으로튜닝하기 1 대역을선택한다음 +/- 를눌러방송국을검색합니다. 방송국이수신되면스캔이중지됩니다. 원하는방송국이수신될때까지이절차를반복합니다. 팁 수신할방송국의주파수를알고있는경우 +/- 를길게눌러원하는주파수에가까워지면 +/- 를반복해서눌러해당주파수로미세조정합니다 ( 수동튜닝 ). 2 선택버튼을길게누릅니다. 설정화면이나타납니다. 3 "BTM" 이나타날때까지컨트롤다이얼을돌린다음누릅니다. 숫자버튼의주파수순서대로방송국이저장됩니다. 9