ROTARY SWITCH 로타리스위치 101

Size: px

Start display at page:

Download "ROTARY SWITCH 로타리스위치 101"

이현 유
5 years ago
Views:

1 0

2 안전을위한주의사항 / Attention list for safety 특징 Characteristics. 의회로는일반적으로 회로부터 9 회로까지조립식으로되어있어회로에따라선택할수있으므로경제적입니다.. Series number is prefabricated from to 9, thus allows for choice according to circuits, so its very economical. 경고 Warning 2. 사용수의선택방법은스톱바볼트 (Stopper Bolt) 를이용하여간단히변경되므로사용이편리합니다. 2. It s very convenient. Because the contact points can be easily changed by using the stopper bolt.. 인명사고및막대한재산상의피해가우려되는기기등에사용할경우에는반드시 2 중으로안전장치를부착한후에사용하십시오. 2. 지정한정격이외로사용시에는상해를입거나재산상의손실이발생할수있으므로주의하여주십시오.. 전원을입력 (ON) 시키기전에반드시결선이올바르게되어있는지확인하십시오.. 제품의분해, 가공, 개조, 수리를하면오작동의원인이되므로절대로하지마십시오.. When it use in a machine that might cause accidents of worker or enormous property damage, It should be used after the double safety device is attached. 2. If it is used with the voltage other than the designated one, it might cause injury for human and property damage.. Before turning on the power, make sure whether the wires are connected correctly.. Do not disassemble, process, remedy or repair this product in any case, because it might cause malfunctioning.. 다이얼스탭 (Dial Step) 각도는 26회로 (AP) 를선택할때는 60 /26 회로로 Step각도가정해지고, 회로 (AA) 를선택할때는 60 / 회로로 Step각도가정해집니다.. 이동이단자에서옆단자가회전할때완전히 OFF상태로변환후다음이 ON상태로되는 60 / 과 OFF상태로되지않고다시옆과 ON상태로되는 60 /26 2종류가있습니다. 5. 특수구조에의한조립식다단, 다련으로설계되었으며최대 60 /26 단 0련까지제작이가능합니다. 사양 접촉저항 0 mω 이하 (DC A, A). When the 26 circuit(ap) is selected, the degree of dial step is 60 /26 circuit. When the circuit(aa) is selected, the degree of dial step is 60 / circuit.. There are 2 kinds of the 60 / contact point which turns to the next contact point at the complete off position and 60 /26 contact point which turns to the next contact point at not off position. 5. It s special structure enables to assemble multi steps and series numbers. (up to 60 /26 step and 0 poles numbers) Specification Contact resistance Less than 0 mω(dc A, A) CODE 주의. 실외에서는사용하지마십시오.. Do not use it outside. 2. 부식성가스 ( 특히유해가스, 암모니아등 ), 가연성가스가발생하지않는장소에서사용하십시오.. 청소시물, 유기용제를사용하지마시고, 물기가없는마른수건이나압축공기등으로청소를하시기바랍니다.. 제품의설치및분리는전원을 OFF 한후에실시하여주십시오. 5. 외부기기와결선시번호를확인후배선을정확하게결선하여주십시오. 6. 제품부착에관하여다음과같은장소를피하여주십시오. ㆍ본체에직접진동, 충격이가하여지는장소. ㆍ티끌과먼지, 염분, 철분이많은장소ㆍ직사일광을받는장소. 7. 본제품의품질향상을위하여색상및일부디자인은사전통보및예고없이변경될수도있습니다. Attention 2. Do not use it in a place, where corrosive gas (especially, harmful gas, ammonia, etc.) and inflammable gases are generated.. For cleaning, use a dry cloth or compressed air, do not use water or fluid solvent.. For installation and separation of this product, make sure the power is OFF. 5. When connecting it with external equipments, check the wire number and make sure it is connected correctly. 6. Avoid the following places when installing the product. ㆍ Place where the main body can receive shock or vibration directly. ㆍ Place with a lot of dusts, dirts, salts or irons. ㆍ Place exposed with a direct sunlight. AC 220V (0.2A 이하 ) 허용전압 DC 220V (0. A 이하 ) 허용전류 AC A (0V 이하 ) DC A (0V 이하 ) 접촉자용량 DC 20W, AC 5W 절연저항 500mΩ 이상 (DC 500V) 내전압 AC 500V, 분간 회로 0.8~2.5Kg/ cm2 2회로 0.9~.0Kg/ cm2 회로.0~.5Kg/ cm2 회로.~.0Kg/ cm2회전토크 5회로.2~.5Kg/ cm2 6회로.~5.0Kg/ cm2 7회로.~5.5Kg/ cm2 8회로.5~6.0Kg/ cm2 9회로.6~6.5Kg/ cm2 AC 220V (Less than 0.2A) Allowable voltage DC 220V (Less than 0.A) AC A (0V Less than) Allowable current DC A (0V Less than) Contact point capacity DC 20W, AC 5W Insulation resistance More than 500mΩ (DC 500V) Withstanding voltage AC 500V, For one minute pole 0.8~2.5Kg/ cm2 2 poles 0.9~.0Kg/ cm2 poles.0~.5kg/ cm2 poles.~.0kg/ cm2 Torque 5 poles.2~.5kg/ cm2 6 poles.~5.0kg/ cm2 7 poles.~5.5kg/ cm2 8 poles.5~6.0kg/ cm2 9 poles.6~6.5kg/ cm2 7. The specifications (colors and parts of design, etc.) are subject to change without prior notice for quality improvement of the product. 회로 회로 2 2 회로 회로 회로 5 5 회로 6 6 회로 7 7 회로 8 8 회로 9 9 회로 AA (27.7 ) AP 26 (.85 ) Poles Contact point Pole 2 2 Poles Poles Poles 5 5 Poles 6 6 Poles 7 7 Poles 8 8 Poles 9 9 Poles AA C.P (27.7 ) AP 26 C.P (.85 ) 02 KEM CO., LTD. TEL : 05) / FAX : 05) / 0

KR- KR TYPE KR-2 KR- KR- KR-5 KRT TYPE 모델 / Model 길이 / Length 모델 / Model 길이 / Length KR- 5.5 KR-6 2 KR-2 5 KR-7 0.5 KR- 70.5 KR-8 58 ACTION : ROTARY RATING : 0.

3 KR- KR TYPE KR-2 KR- KR- KR-5 KRT TYPE 모델 / Model 길이 / Length 모델 / Model 길이 / Length KR- 5.5 KR-6 2 KR-2 5 KR KR KR-8 58 ACTION : ROTARY RATING : 0.25A 0V DC POSITION : -POLE 2-POSITION 25 Ø9 M9X KR- 88 KR KR CODE KR-6 KR-7 KR-8, KR-9 02 회로 2 07 회로 7 08 회로 8 02 pole 2position 07 pole 7position 08 pole 8position 단수조절방법. 를 단으로위치고정합니다. 2. ( 손잡이 ) 위의흑색볼트를돌려서빼냅니다.. ( 손잡이 ) 를해체한후 사각지지대를해체합니다.. BRAKET 양쪽의접시볼트를풀고 BRAKET를빼냅니다. 5. 중앙샤프트부근에있는작은볼트 2EA를.5 바퀴정도풀어놓습니다. 6. KN0B 사각지지대에샤프트를가부착합니다. 7. 작은볼트에부착되어있는단수고정레버 2EA 중 EA를단수에맞추는위치까지이동시킨후 사각지지대를돌려원하는단수에단수고정레버가정위치에있는지확인합니다. 8. 가부착된 사각지지대를해체합니다. 9. BRAKET을방향에맞게삽입한후접시볼트 2EA를고정시킵니다. Way to control step. Fix the to the direction of step. 2. Turn and pick out the bolt in black above.. After dismantling the, then dismantle the square support.. After releasing the flat headed bolt on either side of the BRAKET, pick out te BRACKET. 5. Loosen the 2EA of small bolt in near the middle of shaft by rotating.5 wheel. 6. Temporarily attach the square support of. 7. After moving the EA from 2 EA of gear lever in fixed step to direction which adjust te step to, confirm the gear lever in fixed step at correct direction by rotating the square support of. 8. Dismantle the square support of temporarily attached in shaft. 련수 / 09 회로 9 0 회로 0 회로 2 회로 회로 5 (05 대체 ) 206 2회로 6 (06 대체 ) 0 회로 (0 대체 ) 0 회로 (0 대체 ) Pole/ Position 09 pole 9position 0 pole 0position pole position 2 pole 2position 205 2pole 5position (Replacement:05) 206 2pole 6position (Replacement:06) 0 pole position (Replacement:0) 0 pole position (Replacement:0) 사각지지대는 단방향으로고정되게합니다. KINOB( 손잡이 ) 를사각지지대에고정되게합니다. 단수가맞는지최종확인합니다. 9. After inserting the BRAKET to the right direction fix the 2 EA of the flat headed bolt. 0. Fix the square support of to the direction of step.. Fix the at the square support. 2. Finally confirm that step is correct. * 자세한내용은홈페이지동영상을참조하세요. * For derails, please refer to the video at our homepage. 0 KEM CO., LTD. TEL : 05) / FAX : 05) / 05

KRS TYPE 특징. 리드스위치를사용하여응답성이빠릅니다. 2. 정확한 60, 90 의각도를검출할수가있습니다. Characteristics. Fast Responsibility : Using of a reed switch. 2. Accurate Angles of 60, 90. KRP TYPE KRP-0 NEW -5 Ø28 8 9.5 22 20 7.

4 KRS TYPE 특징. 리드스위치를사용하여응답성이빠릅니다. 2. 정확한 60, 90 의각도를검출할수가있습니다. Characteristics. Fast Responsibility : Using of a reed switch. 2. Accurate Angles of 60, 90. KRP TYPE KRP-0 NEW -5 Ø KEM M0 -TAP 6 0 K 극 (90 ) 6K 6극 (60 ) Contact Point K C.P. (90 ) 6K 6C.P. (60 ) Ø 5 panel cutting hole KRP-0 CODE KRS-000K 0 Ø26 8 M KRS-000K 600mm 7.5 Ø -5 KEM Ø28 28 panel cutting hole M0 -TAP 6 0 WIRE COLOR 백 (WHITE) 갈 (BROWN) 적 (RED) 주 (ORANGE) 노 (YELLOW) STEP COM 2 ANGLE 사양 허용전압 내전압 AC 250V A AC 000V, 분간 Specification Allowable voltage Withstanding voltage AC 250V A AC 000V, For one minute KRS-0006K 0 Ø26 9 절연저항 00mΩ이하 (DC 500V 이하 ) 전기적 0,000 회이하 수명 기계적 0,000 회이하 각도 5 회전토크 N.cm ~ 5N.cm Insulation resistance Less than 00mΩ (Less than DC 500V) Electrical Less than 0,000 times Life Mechanical Less than 0,000 times Rotation angle 5 Torque N.cm ~ 5N.cm M KRS-0006K 8 600mm WIRE COLOR 백 (WHITE) 갈 (BROWN) 적 (RED) 주 (ORANGE) 노 (YELLOW) 녹 (GREEN) 파 (BLUE) STEP COM ANGLE Position 06 KEM CO., LTD. TEL : 05) / FAX : 05) / 07

ROTARY SWITCH 로타리스위치 97

ROTARY SWITCH 로타리스위치 97 97 안전을위한주의사항 / Attention list for safety 경고 1. 인명사고및막대한재산상의피해가우려되는기기등에사용할경우에는반드시 2 중으로안전장치를부착한후에사용하십시오. 2. 지정한정격이외로사용시에는상해를입거나재산상의손실이발생할수있으므로주의하여주십시오. 3. 전원을입력 (ON) 시키기전에반드시결선이올바르게되어있는지확인하십시오. 4. 제품의분해,