KOR ENG INSTALLATION & OPERATION GUIDE BOOK NEXPTZ Camera Explosion proof Security Camera (High Speed Standard Type) 내압방폭카메라 ( 고속일반타입 ) - 1 -
- 2 -
ENG Important Safety Instructions 1. Install and use this system after reading these instruction thoroughly. 2. Keep these instructions. 3. Install in accordance with the manufacture s instruction. 4. Take care of all Cautions and Warnings. 5. Use stainless steel hardware to fasten the mount to outdoor surfaces. 6. Only use replacement parts recommended by the manufacturer. Explanation of Graphical Symbols. This symbol is intended to alert the user to the presence of uninsulated dangerous voltage within the product s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. This symbol is intended to alert the user to the presence of important operating and maintenance(servicing) Instructions in the literature accompanying the appliance. WARNING: To reduce the risk of ignition of Hazardous Atmospheres, disconnect the equipment from the supply circuit before opening. WARNING: To reduce the risk of ignition of hazardous atmospheres, conduit runs must have a sealing fitting or cable gland connected within PT 3/4 inches of the enclosure. TO REDUCE THE RISK OF IGNITION DO NOT OPEN WHEN AN EXPLOSIVE GAS ATMOSPHERE MAY BE PRESENT CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION : TO REDUCE THE RISK OF ELECTRIC SHOCK. DO NOT REMOVE COVER(OR BACK). NO USER SERVICEABLE PARTS INSIDE REFER SERVICING TO QUALIFIED SERVICE PRERSONNEL - 3 -
Methods of Installation This system can be installed in a standard or inverted position or camera Housing only with optional bracket as below Figure1. When installed for inverted operation, the origin of camera shall be reconfigured through the Camera function. There is no need to be adjusted physically but sunshield bracket may not be functional at this case. Standard Position Inverted Position Figure1. Method of Installation WARNING: Gross weight of this system is about 30kg. Use caution when lifting and installing. It is recommended you to wear proper non-slip gloves be worn during installation. - 4 -
ENG Methods of Installation Figure2. Install the product to Pedestal Mount bracket To install this product, please refer to Figure2 and do the following steps. 1. Make sure the threads of the product and the threads of the supplied M8X15mm stainless steel bolts (Supplied) are free of dirt and debris. 2. Apply an amount of thread locking compound(not supplied) to the thread of the product and the thread of the bolts. 3. Secure the product to the mounting surface with the adjusted wrench and four M8x15mm stainless steel bolts and lock washers. Tighten the bolts to 250~350 kgf.cm (24Nm~34Nm) Note : Figure2 shows the product being installed on a Pedestal mount which is an optional product (not supplied) and if there is no need the pedestal mount, just follow a above step to install the product without pedestal mount bracket. - 5 -
Methods of Installation Fiber Filler Sealing compound Cables Sealing Method Explosion proof Flexible conduit (Not Supplied) PT 3/4-14 Nipple PT 3/4-14 (Supplied) Seal Fitting (Not Supplied) Figure3. Install Product to the surface with Pedestal mount bracket To install this product, please refer to Figure3 and do the following steps. 1. Make sure the threads of the supplied four M10X30mm stainless steel bolts (Not Supplied) and flat/spring washers are free of dirt and debris. 2. Apply an amount of thread locking compound(not supplied) to the thread of the product and the thread of the bolts. 3 There are more options such as wall, corner and pole mount bracket to install. (refer to the mount bracket part page) 4. Make sure the seal fitting(not supplied) and the threaded hole of this system are free of the dirt and particles. 5. Assemble Nipple(supplied), the threaded hole of this system, seal fitting and flexible conduit(not supplied) to be fasten firmly and then the cables must be passed through the seal fitting, nipple and flexible conduit. Plus, the sealing fitting, flexible conduit should be acquired IECEx Certification. Note : Figure3 shows the product being installed on a surface with pedestal mount. - 6 -
IN SLAVE OUT RS 485 1 DOME 2 DVR + - + - + - RS 232C ALARM/DVR ENG Base Schematic POWER AC110 or 220V RS 485 +- RS 485 BNC N/O COM Alram out DVR FRONT MAIN MONITOR DATA 2 DATA 1 DC 12V REAR DATA1 REAR DATA2 DC 12V KEYBOARD CONTROLLER HTX-5000 Figure4. Base Schematic of Installation 1. Figure4 is recommended for the base Schematic of Installation. 2. If you wish to consist of another method or other components, you must proceed to do after conferring with a manufacture. 3. Depend on a DVR, you can control the product with an Utility in the DVR without HTX-5000. - 7 -
Cable Configuration BNC Alram In/Out Put POWER (AC 100V ~ 240V) RS-485 Data+, - 2m ± 0.3m Configuration of Wire Harness Figure5. Cable configuration Wire Color Function Description Brown Sky Blue Green Power Input (AC 100V ~ 240V) L1 N GND Red Orange Yellow Green Black Black Red Yellow White Black (Coaxial cable) Blue stripe White stripe Alarm Input Alarm Output A Alarm Output B Video Control Data Alarm 1 Alarm 2 Alarm 3 Alarm 4 GND NO A COM A NO B COM B BNC Cable RS485 Data + RS485 Data - - 8 -
ENG Key Feature and Introduction The NEXPTZ Series camera which is Explosive proof camera features a high resolution Super HAD CCD imager for enhanced lowlight sensitivity. The NEXPTZ Series follow the stringent explosion-proof requirements with creative mechanical strength and design. Moreover, the NEXPTZ explosion-proof system is designed to meet the rigorous requirements of explosionproof electrical equipment installed in hazardous locations. The system has built-in True Day &Night zoom camera with programmable Camera setting easy to setup and program functions. System information aides trouble shooting by displaying the hardware and software version of the driver, baud rate, and protocol. The Highest level Ex Class : Ex d IIC T6 (IECEx, ATEX, CE, FCC, KC) Corrosion resistant SUS 316 Construction IP67 Protection Adapt 650TVL, Optical x36 AF Zoom module 360º Continuous Panning with max 60º/sec High Speed Thanks to Flip function and 360º continuous rotate at Pan/ Tilt angle Various Preset function - Home Function - 128 Preset potions w/ focus, iris, BLC setting - 8 Scan,4 Tours, Pattern Built-in Wiper function 4 Alarm in & 2 Relay out Integrated with Water jet : EXWJ400 Approx 30Kg of light weight - 9 -
Simple Function Control Guide * This function is specialized to HTX-5000 keyboard. Function Process Results Remarks PAN/TILT 1Press 1 and (CAM) button in sequence. 2 Move Joystick to the right, left, up and down. For matching ID 01 If ID set 02, press 2 and (Cam) button You can see the moving as following the direction. ZOOM /FOCUS/ Iris 1 Twist Joystick to the right. 2 Twist Joystick to the left. -ZOOM IN -ZOOM OUT 3 Press 4 Press button. button. -Focus is changed to Near or Far -Return to Auto Focus mode by moving the joystick. -Iris is opened or closed Moving the joystick reactivates Auto Iris mode Wiper Control 1 Press (On) button or Press 2 and (On) button in sequence. (86+ Preset) at Pelco Protocol -Wiper moves as keeping a steady angle. If it not raining, forbid to keep the moving status over 1 hour continually. 2 Press (Off) button or Press 2 and (Off) button in sequence. (79+ Preset) at Pelco Protocol -Wiper stops. Water jet (Optional) 1 Set washing position -.Move the window face to nozzle by using pan/tile and save the position on preset 59. - Set the specific position to wash front window toward the nozzle on preset 59. Check water level in the tank periodically. 2 Press 4 and (On) button. -Run washing and wiping. (88+ Preset) at Pelco Protocol - 10 -
ENG Simple Function Control Guide * This function is specialized to HTX-5000 keyboard. Function Process Results Remarks Menu 1 Press (Menu) button. (95+ Preset) at Pelco Protocol 2 Move Joystick or left. 3 Move Joystick to the right Up or Down. 4 Press (Menu) or ESC (Esc) or (Enter) button twice. -Menu screen is displayed. -Go into the sub-menu items. Change value. Navigate through the menu items -Navigate through the menu items. -Escape from the menu. (Enter) = (94+ Preset) at Pelco protocol (Menu) = (95+ Preset) at Pelco protocol (ESC) = (96+ Preset) at Pelco protocol Preset 1 Set Preset (direct) -.Select one button of ~, 1 1 2 8 (128) and Press (Shift) and -PTZ moves to the position which you have saved the preset. 1~59+ Preset to operate Preset 1~59 at Pelco protocol. (Preset) in sequence. 2Running Preset -.Press Number button and in sequence. Scan 1 Press (Scan) button to set. (60+ Preset) at Pelco Protocol 2 Press Joystick ESC (Esc) button or move to the right or left. -PTZ continually moves between the start and end point which user set among the preset. -Escape from the moving Auto Scan 61~68+ Preset to operate Scan1~8 at Pelco protocol. Tour 1 Press (Tour) button to set. (70+ Preset) at Pelco Protocol 2 Press ESC (Esc) button or move -PTZ continually moves to user set position of the presets. -Escape from the moving Tour. 71~74+ Preset to operate Tour1~4 at Pelco protocol. Joystick to the right or left. Pattern 1 Press (Pattern) button to set. ~ (80+ Preset) at Pelco Protocol 2 Press ESC (Esc) button or move -PTZ continually moves to user set position of the presets. -Escape from the moving Tour. 81~84+ Preset to operate Pattern1~4 at Pelco protocol. Joystick to the right or left. - 11 -
Program and Operation Principle of joystick usage in the programming (editing) mode * This function is specialized to HTX-5000 keyboard. Button or Joystick movement in menu Joystick left or right Joystick up or down Joystick down Zoom handle twist ESC Home or Off button Function Go into the sub-menu items. Execute the command(exit) Change value. Navigate through the menu items. Navigate through the menu items. Finish editing title. Change value.(increase / Decrease) Enter editing title mode. Escape from the menu without change. Delete value or name of the field. Camera Setting (Camera ID, BAUDRATE, PROTOCOL) NEXPTZ cameras must be set up communication before starting the installation. This involves properly setting configuration of Camera ID, BAUDRATE and PROTOCOL. To do set communication initially, You should use the Remote controller which is included to the product additionally. Remote controller can set up communication regardless of Camera BAUDRATE and PROTOCOL When you use the remote controller, the remote controller is better to be towards the window of Camera housing. Refer to below for sequence of entering Communication setting Menu. MENU Communication Select CAMERA ID / BAUDRATE / PROTOCOL - 12 -
ENG Program and Operation MENU TREE 1. FUNCTIONS 1.1 HOME FUNCTION (MENU Functions Home) 1.2 PRESET (MENU Functions Preset or Shortcut: PRST) 1.3 SCAN (MENU Functions Scan or Shortcut: SCAN) 1.4 TOUR (MENU Functions Tour or Shortcut: TOUR) 1.5 PATTERN (MENU Function Pattern or Shortcut: PTRN) 1.6 EXIT 2. ALARM 2.1 ALARM SETUP 2.2 SAVE AND EXIT 3. SCREEN 3.1 PRIVACY ZONE (MENU Screen Privacy Zone) 3.2 NORTH DIRECTION (MENU Screen North Direction) 3.3 ZONE TITLE (MENU Screen Zone Title) 3.4 CAMERA TITLE (MENU Screen Camera Title) 3.5 OSD DISPLAY (MENU Screen OSD Display) 3.6 EXIT 4. CAMERA 4.1 FOCUS CONTROL (MENU Camera Focus Control) 4.2 WB CONTROL (white balance) (MENU Camera WB Control) 4.3 AE CONTROL (auto exposure) (MENU Camera AE Control) 4.4 BLC/WDR SETUP (MENU Cemera BLC/WDR Setup) 4.5 SHARPNESS (MENU Camera Sharpness) 4.6 DIGITAL ZOOM (MENU Camera Digital zoom) 4.7 NIGHT SHOT (MENU Camera Night Shot) 4.8 CAMERA DEFAULT (MENU Camera Camera Default) 4.9 SAVE AND EXIT 5. SETUP 5.1 INSTALLATION (MENU Setup Installation) 5.2 SPEED (MENU Setup Speed) 5.3 PANNING RANGE (MENU Setup Panning Range) 5.4 CALIBRATION (MENU Setup Calibration) 5.5 FACTORY DEFAULT (MENU Setup Factory default) 5.6 ERASE DATA (MENU Setup Erase data) 5.7 SYSTEM INFORMATION (MENU Setup System Information) 5.8 SAVE AND EXIT 6. PASS WORD 6.1 ENABLE PASSWORD (MENU Password Enable Password) 6.2 EDIT PASSWAORD (MENU Password Edit Password) 6.3 SAVE AND EXIT 7. COMMUNICATION 7.1 EXPTZ ID (MENU Communication EXPTZ ID) 7.2 BAUDRATE (MENU Communication Baudrate) 7.3 PROTOCOL (MENU Communication Protocol) 7.4 SAVE AND EXIT 8. RUN FUNCTION 8.1 FUNCTION 8.2 NUMBER 8.3 RUN 8.4 EXIT - 13 -
Program and Operation 1. FUNCTION Pressing the MENU button on the keyboard controller, the following On-screen MAIN MENU will be shown on your monitor screen Main Menu Function Alarm Screen Camera Setup Password Communication Run Function Exit Locate the cursor on the FUNCTION item and then push the joystick to the right to enter FUNCTION menu. Function Home Function Preset Scan Tour Pattern EXIT 1.1 HOME FUNCTION (MENU =>FUNCTION => HOME FUNCTION) After HOME FUNCTION item has been selected, follow the directions below to set HOME function. Home Function Function : Tour Number : --- Time : 010 SEC Operation : DISABLE Save And Exit Function : Tour/ Preset/ Scan Number : - - - Time : 10~240 Seconds Operation : ENABLE/ DISABLE - 14 -
ENG Program and Operation The Home function applied to the predefined functions such as Preset, Tour, Pattern, or Scan function after the keyboard controller has been idle for a programmed time. Follow the steps below to program the Home function: 1.Select the camera number by pressing No. and CAM 2.Press MENU to display the main menu on the monitor. 3.Push the Joystick to the right on FUNCTION. 4.Enter Home Function menu by pushing the Joystick to the right. 5.Push the Joystick to the right/ left (or twist CCW/CW) to scroll Tour, Auto Scan and Preset functions. 6.Select Function Number by pushing the Joystick down, and twist the Joystick to the CCW/CW (or push right/left). The executable function number will be scrolled. If selected function is not programmed, it won t change. Go to setup function first. 7.Pushing the Joystick down and twist the Joystick to CCW/CW (or push the stick to right/left) to set waiting time. 8. Locate the cursor on OPERATION option by pushing the Joystick down. Choose operation status Enable or Disable by pushing the Joystick to the right or to the left (or twist CCW/CW). 1.2 PRESET (MENU =>FUNCTION => PRESET ; Short cut : Preset) Preset memorizes pan, tilt, zoom, focus and iris settings. Once programmed, pressing combination of 0 ~9 numbers and a Preset button on your controller automatically calls up the preset position. Presets may be assigned to alarm actions or as the home position for the NEXPTZ camera. Locate the cursor on the PRESET item and then push the joystick to the right to enter PRESET menu. Function Home Function Preset Scan Tour Pattern EXIT - 15 -
Program and Operation There are 16 pages of preset programming menu. Each page can hold 8 presets. Locate the cursor on PREV NEXT, preset menu pages can be scrolled by pushing the Joystick to the Left or Right on the PREV NEXT. PRESET 01/16 NO. F I B TITLE 001 A A F xxxxxxxxxxxxxxxx 002 M M O ---------------- 003 - - - ---------------- 004 - - - ---------------- 005 - - - ---------------- 006 - - - ---------------- 007 - - - ---------------- 008 - - - ---------------- PREV NEXT SAVE AND EXIT F : FOCUS I : IRIS B : BLC X : 16 digit of preset title - : not defined : Current cursor position F : A(Auto Tracking)/ M(Manual Tracking) I : A(Auto Iris)/ M(Manual Iris) B : F(BLC OFF)/ O(BLC ON)/ W(WDR) Follow the steps below to program the Preset positions. 1. Select the camera number by pressing 0 ~9 and CAM. 2. Simply press Preset button to enter preset menu. ( MENU => FUNCTION => PRESET) 3. Select the empty preset location to be programmed using the Joystick up/down. If selected location is not empty, pressing Preset button will show your predefined position. 4. After selecting an empty position, twist the Joystick to control the direction of the camera and lens. Position Pan : 000.0 Tilt : 000.0 Select Position Press Focus To Save - 16 -
ENG Program and Operation 5. After aiming the camera (view direction and lens control) at specific position, push the focus button(near, Far). The selected location No. field will be filled with A A F. Push the joystick to the right to select each Focus/ Iris /BLC mode using zoom handle. 6. Move the cursor to the title field to edit/enter the title. Rotate the handle CW and CCW to scroll through the alphanumeric characters. Push the handle to right or left to select next or previous digit. 7. To finish entering the title, Select Save and Exit by pushing the Joystick to the right. 8. Locate the cursor on PREV NEXT item to select the previous/next page of presets, scroll the page by pushing the Joystick to the Left on PREV NEXT. 9. Repeat steps 2 through 8 for each additional preset position. 10. Select Save and Exit by pushing the Joystick to the right. Press ESC to exit the Preset menu without saving NOTE: Press the Home or OFF button at programmed position to delete a programmed preset view. <Shortcut of Preset Program> Select direction of the camera, zoom and focus to be programmed, then press No. (1~128), and then press Shift, Preset subsequently. The current view will be stored to the selected preset number if position is empty. If selected preset number is not empty, PRESET EXISTING message will be displayed on the monitor and you will be prompted to overwrite. Example: 1, 0 + shift + Preset will memorize current view as preset No. 10. In this case, focus and Iris mode will be memorized as auto and dwell time will be set to 3 sec. - 17 -
Program and Operation 1.3 SCAN (MENU =>Function => Scan ; Short cut : SCAN) The Scan function supports up to 8 programmed section of angles at 8 programmable speeds. Scan Menu 01/08 Scan 01 : AUTOSCAN01 Speed : 1~8 Start : 127.1, 027.0 zoom End : 157.7, 080.7 zoom Dir : CCW (PAN:000.0) Swap : OFF Save And Exit SCAN01 : AUTOSCAN01 ~ SCAN08: AUTOSCAN08 SPEED(MODE) : 1/ 2 / 3/ 4/ 5/ 6/ 7/ 8 Follow the steps below to program Scans. 1: SLOWER 8 FASTER 1.Press the SCAN key to enter Auto Scan menu directly. (or MENU => Function => Scan). 2.Select the Scan number by pushing the Joystick left or right. 3.Twist the Joystick to enter the title by scrolling through the alphanumeric characters and pushing the handle to the right or left to move to the next space. Press ENTR key or push the Joystick down to finish title mode. 4.Push the Joystick downward to select SPEED and set the speed by twisting the Joystick clockwise or counterclockwise or moving the Joystick left/ right to select the auto scan speed. 5.When finish entering the title, Select START with the Joystick to the left or right and select the start position. Current panning position will be displayed. To complete the selection of the start position hit the Focus button to stop.(or twist zoom handle or hit zoom button to start PTZ control for view selection and hit the Focus button to stop.) 6. Move the Joystick downward to select END. Move the Joystick to select the end position. To complete the selection of the end position hit the Focus button to stop. 7.Move the Joystick downward to select DIR(Direction) Set the scan direction by moving the Joystick left and right to select the auto scan direction.(cw or CCW) 8. Move the Joystick downward to select SWAP and set the swap by moving the Joystick left and right to select the swap ON or OFF. 9. Select Save and Exit by pushing the Joystick to the right. Press ESC to exit the program without saving. Note : Pressing the HOME or OFF Button to delete stored data, - 18 -
ENG Program and Operation 1.3 TOUR (MENU => Function => Tour ; Short cut : TOUR) There are 4 programmable Tours. Each Tour consists of up to 32 Preset positions, Patterns, Scans, or other Tours. Using second-level Tours, it can be expanded to over 56 functions in a single Tour. However tours second level Tours will be ignored when called by a Tours. This can be best illustrated by the following example: If Tour 01 : Preset 02, Preset 03,Tour 02, Tour 03 Tour 02 : Preset 05, Preset 06, Tour 04, Preset 05 Tour 03 : Preset 07, Pattern01 Tour 04 : Preset 08. Preset 05, Pattern01 Tour01 executes as follows: Preset 02 Preset 03 Preset 05 Preset 06 Preset 05 Preset 07 Pattern01... (Repeat) ---Tour 04 in Tour 02 will be skipped in Tour 01 Tour02 executes as follows: Preset 05 Preset 06 Preset 08 Preset 05 Pattern01 Preset05 Repeat (Tour4 is still valid if called directly from Tour2.) TOUR 01:xxxxxxxxxxxx 01/04 FUNC NO S DW TITLE PRST 001 S 03 ---------------- SCAN 016 S 03 ---------------- TOUR 008 S 03 ---------------- ---- --- - -- ---------------- ---- --- - -- ---------------- ---- --- - -- ---------------- ---- --- - -- ---------------- PREV NEXT SAVE AND EXIT xxxxx : 16 digits of title for tour label - - - : blank preset position Speed : Fast (Normal)/ Slow DWell : 01-99 Sec PRST : Preset 1~128 PTRN : Preset 1~4 SCAN : SCAN 1~8 TOUR : TOUR 2~4-19 -
Program and Operation Follow the steps below to program the Tours: 1. Press MENU => Function => TOUR (Short Cut: TOUR) to display the main menu on the monitor. No. + SHFT+TOUR will open directly Tour No. 2. Choose an empty location of function by pushing the Joystick up or down. 3. Move the Joystick to left or right to enter the edit mode. Stored Preset view can be recalled by pressing Preset button, the camera will move to the stored Preset view. 4. To place predefined functions as a Tour, press the function buttons (such as Tour, Pattern, or Scan, Preset ). Then select function No. by twisting the Zoom handle. (Programmed function No. will be scrolled). To remove functions from the Tour, press the HOME button, blank position mark (- - -) will be displayed. You can overwrite the programmed position. 5. Repeat Step 2 through 4 for each desired position. Each title will be displayed on top of the line. 6. Up to 32 Presets, Tours, Patterns Scans can be selected for a Tour. You can expand the Tour sequence by calling other programmed tours. Push the Joystick handle to right or left while the cursor is on the top of the line (TOUR 01) to select another page of the Tour menu. (TOUR 01) 7. You can enter a title for the selected Tour by twisting the Joystick while the cursor is on the top of the line (TOUR 01). Rotate the handle clockwise or counterclockwise to scroll through the alphanumeric characters. Push the handle to the right or left to select the next or previous digit. 8. Select Save and Exit by pushing the Joystick to the right. Press ESC to exit the program without saving. Note : Pressing the HOME or OFF Button to delete stored data. - 20 -
ENG Program and Operation 1.4 PATTERN (MENU => Function => Pattern ; Short cut : PATTERN) The Pattern function stores user s control of the selected dome camera for up to 240 seconds. 4 patterns can be stored in 240 seconds of total recording space. Stored pattern is played back by pressing No.+ Pattern buttons subsequently Pattern Setup NO TILTIE SEC O1 : PATTERN1 000 O2 : PATTERN2 041 O3 : PATTERN3 010 O4 : PATTERN4 020 TOTAL: 071 Save And Exit Follow the steps below to program the Pattern: 1. Select the camera number by pressing 0 ~9 and CAM. 2. Simply press the Pattern key. (or MENU => Function =>Pattern) 3. Select the empty Pattern number to be programmed by pushing the Joystick Up or Down. If SEC column is not 000, then the selected No. of pattern is already recorded. 4. Twist the Joystick to enter recording mode and control the camera direction with the Joystick. Your controls will be automatically recorded. You can repeat this procedure until you are satisfied with the pattern recorded. (Or twist zoom handle or hit zoom button to start PTZ control for view selection and hit the Focus button to stop.) 5. Scroll down to the Save and Exit option and push the Joystick to the right to save and exit. 6. You can title the selected Pattern by pushing the Joystick to the left or right. Rotate the handle clockwise or counterclockwise to scroll through the alphanumeric characters, push the handle to right or left to select next or previous space. 7. Pressing ESC will not save currently recorded data and exits to the previous menu mode. Press the HOME or OFF button at any programmed position to delete the programmed pattern. NOTE: If total recording time reaches 240 seconds, it will automatically stop. The PATTERN function can support PAN and TILT without ZOOM. - 21 -
Program and Operation 2. ALARM Main Menu Function Alarm Screen Camera Setup Password Communication Run Function Exit Locate the cursor on ALARM item in the main menu and push the joystick to the right for ALARM programming of the camera. Alarm Setup No Fun Pri In Out Hld Latch 01 001 3 OFF OFF 001 OFF 02 002 3 OFF OFF 001 OFF 03 003 3 OFF OFF 001 OFF 04 004 3 OFF OFF 001 OFF Save And Exit No : Alarm input number Fun : Priority 1~8calls Preset(xxx), : Priority 0 supports dedicated functions like a Pattern(Pxx), Tour(Txx), Scan(Sxx). Pri(Priority) : Lower No. has higher priority, Equal priority alarms will be serviced repeatedly. In : NO/NC - normally open /Closed, OFF - ignore Out : RO1 - Relay out 1, RO2 Relay out2 OFF - No output. Hld(Hold) : Alarm will be held for programmed time (01 to 255 seconds) Latch : ON - Shows all alarms including past alarm, OFF - Shows activated alarms only. There are 9 levels of priority. 0 : Highest priority supports repeated/dedicated functions like a Pattern(Pxx), Tour(Txx), Scan(Sxx). 1~8: Same level of alarm calls presets one after the other. - 22 -
ENG Program and Operation 1. Press Menu to display the main menu on the monitor. Select the Alarm option by pushing the Joystick up or down and push to right to enter the detail menu. 2. Select the alarm input number by pushing the Joystick up or down and select the column you wish to setup. Selected position will be highlighted. 3. Select the Preset, Status of Input (NC/NO/OFF), and Output (RO1/RO2/OFF) by pushing the Joystick to the right or to the left. 4. To increase or decrease the preset number or to change the status or output number, twist the Joystick clockwise or counterclockwise. In case of preset, programmed preset number will be scrolled. 5. Locate the cursor on Save and exit and push the Joystick to the Save and exit. Press ESC to exit the program without saving. 3. SCREEN Pressing the MENU button on the keyboard controller, the following On-screen MAIN MENU will be shown on your monitor screen. Main Menu Function Alarm Screen Camera Setup Password Communication Run Function Exit Locate the cursor on the SCREEN item and then push the joystick to the right to enter SCREEN menu. Screen Setup Privacy Zone North Direction Zone Title Camera Title OSD Display Exit - 23 -
Program and Operation 3.1 PRIVACY ZONE (MENU => Screen => Privacy Zone) Locate the cursor on the PRIVACY ZONE item and then push the joystick to the right to enter the menu. Screen Setup Privacy Zone North Direction Zone Title Camera Title OSD Display Exit This function disables the viewing of restricted areas for privacy reasons. Mask up to 8 unwanted views in a camera. Privacy Zone Setup NO TITLE Method Color 01 xxxxxxxxxxxxxxxx MASK BLU 02 xxxxxxxxxxxxxxxx V.OFF BLU 03 ---- 04 ---- 05 ---- 06 ---- 07 ---- 08 ---- Save And Exit Method : BLOCK / V.OFF / MOSA / None Color :BLUE/SKY/RED/YELLOW/CYAN/GREEN/MAGNET/WHITE/GRAY 1. Select the Privacy Zone option by pushing Joystick Up or Down and push to right to enter the detail menu. 2. Select the privacy zone number by pushing the Joystick up or down. 3. To enter the zone name, rotate the handle clockwise or counterclockwise. You can select alphanumeric characters by rotating the handle. Move to the next character position by pushing the Joystick to the right. To finish entering the title, push the Joystick down or press the ENTER key. - 24 -
ENG Program and Operation 4. To adjust the marked (privacy) area, press zoom button or twist the Joystick to enter control mode and then use the Joystick (direction and zoom) until you get desired view. Press the Focus button to exit from control mode, the right column will be set to ON. 5. You can overwrite an existing zone. Use the Home key to delete the marked zone, or push the Joystick to the right or left to turn the stored zone On or Off. 6. Select the mask color by pushing the Joystick left or right 7. Select the Save and Exit option by pushing the Joystick up or down. Save and exit the program by pushing the Joystick to the right. Press ESC to exit the program without saving. Press the HOME or OFF button to delete programmed privacy zone. 3.2 NORTH DIRECTION (MENU => Screen => North Direction) Push the joystick handle to the right to select NORTH DIRECTION options North Direction Position : ---.- Save And Exit Move to POSITION item to set north direction, use the Joystick (direction and zoom) until you get desired direction. Release the key then current pan angle will be displayed on position item. (Or twist zoom handle or hit zoom button to start PTZ control for view selection and hit the Focus Button to exit from control mode.) 3.3 ZONE TITLE (MENU => Screen => Zone Title) Enter a specific name in sectioned angle between START and END. Zone Title 01/03 No Title Start End 01 WINDOW 123.4 345.6 02 ----- ----- 03 ----- ----- 04 ----- ----- 05 ----- ----- 06 ----- ----- PREV NEXT Save And Exit - 25 -
Program and Operation 1. Press MENU => SCREEN => ZONE TITLE to display zone title menu on the monitor. 2. Select the zone number by pushing the Joystick up or down. Select Start, End or number column to be set by pushing the handle to the right or left. The selected column will be highlighted. 3. Twist the joystick handle on the No. column to enter zone title. You can select alphanumeric characters by rotating the handle. Move to the next character by pushing the Joystick to the right. To finish entering the title, push the Joystick to the right or left on Save and Exit. 4. To adjust panning limit, twist the Joystick. Then use the Joystick to go the desired direction. The end limit must be in an increasing direction. (Start < End). (Or twist zoom handle or hit zoom button to start PTZ control for view selection and hit the Focus button to exit from control mode.) 5. PREV NEXT : got to previous page or next page of the menu. 6. Save and exit the program by pushing the Joystick to the right. Press ESC to exit the program without saving. 3.4 CAMERA TITLE (MENU => Screen => Camera Title) Push the joystick handle to the right to select CAMERA TITLE options Camera Title Setup Title : CAM No. Save And Exit 1. Twist the joystick handle on the TITLE : CAM No. to enter camera title. You can select alphanumeric characters by rotating the handle. Move to the next character by pushing the Joystick to the right. Camera title is limited to 10 characters. To finish entering the title, push the Joystick to the right or left on Save and Exit. 2. Save and exit with joystick handle to right (Or ESC to exit without saving) - 26 -
ENG Program and Operation 3.5 OSD DISPLAY (MENU => Screen => OSD Display) OSD Display Function Title : ON Camera Title : ON Zone Title : ON North Direction : OFF Camera Position : ON Camera ID : ON Zoom Magnification : ON Save And Exit 1. Move the joystick handle right. You can select OSD DISPLAY ON/OFF each functions. 2. Save and exit with joystick handle to right ( Or ESC to exit without saving) 4. CAMERA Pressing the MENU button on the keyboard controller, the following On-screen MAIN MENU will be shown on your monitor screen. Main Menu Function Alarm Screen Camera Setup Password Communication Run Function Exit NOTE: The menu features will vary depending on the camera module installed in your NEXPTZ camera. - 27 -
Program and Operation Camera Menu Focus Control WB Control AE Control BLC/WDR Setup Sharpness : 6 (1~15) Digital Zoom : OFF/2x/4x/MAX Night Shot Camera Default Save And Exit 4.1 FOCUS CONTROL (MENU => Camera => Focus Control) Focus Setup Mode : MANUAL AF Sensitivity : NORMAL Exit Mode : MANUAL / AUTO AF Sensitivity : NORMAL / LOW CAUTION : Please avoid continuous, 24-hour use of the auto focus heavy movement condition. This will shorten the lifespan of the lens. 4.2 WB (white Balance) CONTROL (MENU => Camera => WB Control) WB Setup Mode : AUTO R.GAIN : N/A B.GAIN : N/A Exit Mode: AUTO / INDOOR / OUTDOOR / ONE PUSH / ATW / MANUAL MANUAL : Control of R and B Gain AUTO : Computes the white balance value output using color information from the entire screen automatically.(3000 to 7500 K) INDOOR : 3200 K base mode OUTDOOR : 5800 K base mode R.GAIN : 0~255 B.GAIN : 0~255 Use the AUTO mode for normal use. R.Gain / B.Gain modes are controllable only in MANUAL Mode - 28 -
ENG Program and Operation 4.3 AE(Auto Exposure) CONTROL (MENU => Camera => AE Control) Depending on your NEXPTZ camera, you will see either the following screen or the next. AE Setup Mode : FULL AUTO Slow Shutter : x10 Iris : Auto Gain : Auto Bright : 008 Shutter : Normal Exit Mode : FULL AUTO / MANUAL / IRIS PRIO / SHUTTER PRIO Slow Shutter : ON/OFF(AUTO mode only) Iris : OPEN / CLOSE / 01 / 02 / / 16 Gain : 0 / 2 / 4 / / 30 db Bright : 000 ~ 015 / NORMAL (008: Default) Shutter : 1/60(1/50), 1/100(1/120),1/250, 1/500, 1/1000, 1/2000, 1/4000, 1/10000, 1/20000, 1/50000. 1/100000 NOTE : Values in ( ) are for PAL Camera. 4.4 BLC/WDR SETUP (MENU => Camera => BLC/WDR Setup) Objects in front of bright backgrounds will be clearer with BLC ON/AUTO BLC/WDR Setup BLC/WDR : OFF WDR Lever : 07 Exit BLC/WDR : OFF / BLC / WDR WDR LEVEL : N/A, 1 ~ 7 (WDR Mode) 4.5 SHARPNESS (MENU => Camera => Sharpness) Sharpness : 1~15 The higher, the more enhanced edges in the picture. : 1~15-29 -
Program and Operation 4.6 DIGITAL ZOOM (MENU => Camera => Digital Zoom) Digital Zoom : OFF (Optical Zoom only) / 2x / 4x / MAX (16x) Camera Menu Focus Control WB Control AE Control BLC/WDR Setup Sharpness : 6 Digital Zoom : OFF Night Shot Camera Default Save And Exit 4.7 NIGHT SHOT (MENU => Camera => Night Shot) Night Shot Setup Mode Local Control Exit : AUTO : OFF The NIGHT SHOT option removes the IR Cut filter of the camera and makes the camera sensitive to near infrared. If NIGHT SHOT mode of the selected camera is set to Manual, 10+ ON will enable the NIGHT SHOT mode, 10+ OFF will turn off the NIGHT SHOT mode Mode : MANUAL / AUTO AUTO Camera automatically goes into B&W mode at low light. MANUAL Manually controls the Night Shot mode in LOCAL CONTROL option. On/Off Night Shot mode remotely by pressing 10+ ON/ 10+ OFF. 4.8 CAMERA DEFAULT (MENU => Camera => Camera Default) Returns all changed camera values to factory default. Camera Default Are you sure?(yes/no) YES : ENTER KEY or MENU KEY NO : ESC KEY - 30 -
ENG Program and Operation 5. SETUP Main Menu Function Alarm Screen Camera Setup Password Communication Run Function Exit Locate the cursor on Setup item in the main menu and push the joystick to the right for Setup programming of the camera. Setup Menu Installation : NORMAL Speed : FAST Panning Range Calibration Factory Default Erase Data System Information Save And Exit 5.1 INSTALLATION (MENU => Setup => Installation) This function can make the installation on the normal surface or ceiling when the NEXPTZ Camera is mounted. NORMAL CEILING : When a Camera is installed on the floor, objects can be displayed normally. : When a Camera is installed on the ceiling, objects can be displayed normally. 5.2 SPEED (MENU => Setup => Speed) FAST : 60 / sec (MAX) SLOW : 10 / sec MID : 30 / sec - 31 -
Program and Operation 5.3 PANNING RANGE (MENU => Setup => Panning Range) Panning Range RIGHT LIMIT : ---.- LEFT LIMIT : ---.- ENABLE : OFF SWAP RIGHT/LEFT Save And Exit When NEXPTZ Camera in installed near a wall or on a corner, panning range(angle) can be limited with this function by user. 5.4 CALIBRATION (MENU => Setup => Calibration) Calibration Origin Reset Origin Position Move Origin Offset : DISABLE Auto Calibration : OFF Save And Exit Origin Reset : Calibrate the ORIGIN point. Origin Position Move : Adjust the small amount of position error from re-installation. Origin Offset : DISABLE / ENABLE Auto Calibration : the Camera calibrates automatically when the deviation of camera position by force or vibration is detected. 5.5 FACTORY DEFAULT (MENU => Setup => Factory Default) Factory Default Are you sure?(yes/no) YES : ENTER KEY or MENU KEY NO : ESC KEY Programmed data go back to initial state as ex-factory. - 32 -
ENG Program and Operation 5.6 ERASE DATA (MENU => Setup => Erase Data) Erase Programmed DATA Are you sure?(yes/no) YES : ENTER KEY or MENU KEY NO : ESC KEY Erase programmed data in the EEPROM of the selected NEXPTZ camera. Press MENU or ENTER button to erase data, ESC key to exit without erasing. Origin offset value is not affected. CAUTION: Unless you download the data into a safe place, all the data in the selected EXPTZ camera will be lost. 5.7 SYSTEM INFORMATION (MENU => Setup => System Information) System Information Camera Type : xxxxxx H/W Version : V1.0 ROM Version : V1.2 Protocol : S2E Buadrate : 9600BPS Exit This screen shows information of the NEXPTZ camera for service or trouble shooting. 6. PASSWORD Password Setup Enable Password : ON/OFF Edit Password : **** Save And Exit You can change or set the password with 4-digit characters in this menu. 1. Change password : Move the joystick handle right and up or down or twist to select number 0~9(a number of four figures), and do same way to confirm. 2. Save and exit with joystick handle to right ( Or ESC to exit without saving) - 33 -
Program and Operation 7. COMMUNICATION Communication Setup EX PTZ ID : 0001 Baudrate : 9600 Protocol : AUTO Save And Exit 1. Move the joystick handle right. You can select EXPTZ ID to select the joystick up or down. 2. Move the joystick handle right. You can select BARDRATE (2400/ 4800/ 9600/ 19200/ 38400) to select the joystick up or down. 3. Move the joystick handle right. You can select protocol by the joystick up or down. The protocol can support PP(Pelco P), PD(Pelco D), EZ, etc. 4. Save and exit with joystick handle to right ( Or ESC to exit without saving) 5. You should use the remote controller which was included to the product to change its protocol for communicating and initial setting. 8. RUN FUNCTION Run Function Function : Number : Action Run Exit 1. Select the function and number which has been stored previously. 2. Select Run by moving the joystick to right. - 34 -
ENG Specifications General Mechanical & Electrical Spec Models NEXPTZ364NA NEXPTZ364PA Signal System NTSC PAL Ex. Class Certifications Front window Ex d IIC T6 IECEx, ATEX, CE, FCC, KC Fully tempered plate glass Material SUS 316 Protection Degree IP 67 Pan & Tilt Pan / Tilt Angle: 360 Continuous rotation Speed: 0.5 ~ 60 /sec (Manually, Proportional to Zoom, Vector Scan) 60 /sec Max (Preset) Auto Scan Preset Pattern Tour Alarm Control Input Voltage Power consumption 8 Scan Selectable 128 positions with focus 4 Pattern, 240 second 4 Tour Selectable Input: 4 Normal dry contacts (Selectable NC/NO) Output: 2 Normal relays 30VDC/1A max. (Normally Open) RS-485(Only Analog Type) 100-220 V~, 50/60Hz MAX 150W Operating Temperature -20 C ~ 60 C Weight Approx. 30 kg - 35 -
Specifications Camera Optical Models Spec NEXPTZ364NA NEXPTZ364PA Image Sensor 1/4" SONY Super HAD II (Double Scan) CCD Total pixels 1028(H) X 508(V) 1028(H) X 596(V) Scanning System 2:1 Interlace Scanning Frequency 15.734kHz(H),59.94Hz(V) 15.625kHz(H),50Hz(V) Sync. System Internal Resolution 650 TV lines in color @ HR 7 mode (700TV lines in B/W @ 7 mode) Min. illumination Color : 0.5lx, B/W : 0.2lx (Color DSS : 0.001lx, B/W DSS : 0.0001lx) S/N Ratio More than 50dB (AGC OFF) Lens Type X36 Day & Night Zoom Lens Lens Zoom Ratio Optical x36 times, Digital x16 times Lens Focal Length f = 3.4mm ~ 122.4mm Lens Aperture Ratio F1.6 (wide) ~ F4.5 (tele) - 36 -
ENG Dimensions Unit (mm) - 37 -
Optional Accessories Note: These Mounting Accessories are not supplied with the EXPTZ Series units. These are purchasing parts. MODEL NAME 1. NEXPTZ-PD: Pedestal mount bracket designed to mount NEXPTZ Series directly to a horizontal surface in either an upright or inverted position. 2. NEXPTZ-WL: Wall mount bracket designed to mount the NEXPTZ Series Camera directly to a load-bearing vertical surface. 3. NEXPTZ-CN: Corner adapter Bracket for use with the NEXPTZ-WL to mount the NEXPTZ Series Camera to the corner of a structure. 4. NEXPTZ-PL: Pole adapter Bracket for use with the NEXPTZ-WL to mount the NEXPTZ Series Camera to a vertical pole or itself to mount the NEXPTZ Series to a horizontal pole. * Recommended pole diameter is Φ12cm to Φ25cm. General NEXPTZ-PD NEXPTZ-WL NEXPTZ-CN NEXPTZ-PL Material SUS304 Polished SUS304 Polished SUS304 Polished SUS304 Polished Maximum Load 50kg 55kg 58kg 56kg Unit Weight 1.5kg 6.5kg 4.8kg 4.5kg - 38 -
ENG Optional Accessories EXPTZ-PD Unit (mm) EXPTZ-WL Unit (mm) - 39 -
Optional Accessories EXPTZ-CN Unit (mm) EXPTZ-PL Unit (mm) - 40 -
ENG Remote Controller 1. POWER Power on/off. 2. NUMBERS Numeric keypads (0~9), 3. Camera Address (ID) Change camera ID. Number + CAM 4. WRITE PRESET(1~99) Saves camera picture s condition. Number + SAVE 5. PRESET(1~99) Recall preset. Number + PRESET 6. HOME Immediately calls Home function. 7. MENU OSD menu on. 8. DOWN / UP / LEFT / RIGHT Moves up/down in the menu. Moves left/right in the menu. Decreases/increases control. 9. ZOOM Zoom in/out 10. FOCUS Controls Focus. 11. IRIS Controls Iris. - 41 -
Honeywell Security Group. Honeywell Co., Ltd. Address : 5F, Sangam IT Tower, B4-4block, 1590 Sangam-dong Mapo-gu, Seoul 121-835, Republic of Korea TEL : +82 2 799 6114 / 6395 FAX : +82 2 792 9011/ 799 6188 E-mail: info.security@honeywell.com Printed in Korea
KOR INSTALLATION & OPERATION GUIDE BOOK NEXPTZ Camera 내압방폭카메라 ( 고속일반타입 ) - 43 -
- 44 -
KOR 안전상의주의사항 1. 본제품을사용하시기전에 안전상의주의사항 을반드시읽은후사용하십시오. 2. 사용설명서를읽은후꼭보관하시오. 3. 제조사의지침에따라서설치하시오. 4. 모든주의및경고문구에대해서유의하십시오. 5. 외부환경설치면에고정시스텐리스재질의기구물을사용하시오. 6. 오직제조사에서권장하는대체부품만사용하시오. 심볼설명 삼각형내의화살표로되어있는번개표시는제품의노출된부분에인체에감전의위험이있는수준의전압이흐르고있음을나타내고있습니다. 삼각형내의느낌표는운용및유지보수 ( 서비스 ) 에대한중요한지침서가제품에딸려있음을나타내고있습니다 경고 : 위험지역에서의화재나감전의위험을줄이기위하여, 제품을열기전에꼭전원을차단하십시오. 경고 : 위험지역에서의화재나감전의위험을줄이기위하여, 제품인입구단의케이블을실링피팅이나케이블그랜드로필히마감처리를하십시오. 점화로인한화재나폭발의위험을줄이기위하여, 폭발가능가스가있을지모르는위험지역에서는절대제품을열지마십시오. CAUTION 주의 감전의 RISK OF 위험이 ELECTRIC 있으니, SHOCK 절대열지마시오. DO NOT OPEN 주의 : 감전으로인한위험을줄이기위하여, 절대덮개를제거하지마십시오. -345- -
설치방법 이제품은아래 Fiqure1 과같이기준정방향또는역방향으로설치될수있습니다. 또한, 제품에적용되는브라켓또는아답터에따라설치방법을바뀔수있습니다. 정방향 역방향 그림 1 설치방법 경고 : 제품의총중량이대략 30kg 이므로제품설치시들어올릴경우주의를요하며, 설치하는동안미끄럼방지장갑을착용할것을권장합니다. -46- -
KOR 설치방법 그림 2. 받침대브라켓에제품설치 그림 2 를참조하여다음단계에따라제품을설치하시기바랍니다. 1. 설치에사용할스텐리스육각구멍붙이볼트 (M8X15mm) 의나사산이정상인지이물질이없는지확인하십시오. 2. 볼트체결전풀림방지를위한화합물 ( 제품구성에포함안됨 ) 을볼트나사산에적용후볼트를체결하십시오. 3. Φ6 렌치를이용하여볼트를 250~350kgf.cm(24Nm~34Nm) 의힘으로체결후표면의설치상태를확인하십시오. Note : 그림 2 는추가선택사양으로구성된받침대브라켓에제품이설치되는상태를보여주고있으며, 받침대브라켓이필요없는설치환경표면에는위단계에따라제품을설치하십시오. -547- -
설치방법 필터 Sealing compound 케이블 실링방법 방폭 후렉시블케이블 ( 포함안됨 ) PT 3/4-14 니플 PT 3/4-14 ( 포함 ) 실링피팅 ( 포함안됨 ) 그림 3. 받침대브라켓을이용하여제품이올려질표면에제품설치 그림 3 를참조하여다음단계에따라제품을설치하시기바랍니다. 1. 설치에사용할스텐리스육각볼트 (M10X30mm) 와너트의나사산이정상인지이물질이없는지확인하십시오. 2. 볼트체결전풀림방지를위한화합물 ( 제품구성에포함안됨 ) 을볼트나사산에적용후볼트를체결하십시오. 3. 또한, 제품에적용되는월라켓또는코터, 폴아답터에따라설치구성이바뀔수있습니다. ( 추가구성설치브라켓페이지를참조하십시오 ) 4. 설치에사용할실링피팅구성품의나사산이정상인지먼지와같은이물질이없는지확인하십시오. 5. 니플을제품케이블인입구단에나사산을이용하여체결하고, 실링피팅과후렉시블케이블을단단히연결한다. 이때제품에서나오는모든케이블류는실링피팅을통하여나와야한다. 추가로실링피팅및후렉시블케이블은 IECEx 인증을취득한제품이어야한다. Note : 그림 3 은받침대를이용하여설치하는제품상태를을보여줍니다. -648- -
IN SLAVE OUT RS 485 1 DOME 2 DVR + - + - + - RS 232C ALARM/DVR KOR 기본시스템구성도 POWER AC110 or 220V RS 485 +- RS 485 BNC N/O COM Alram out DVR FRONT MAIN MONITOR DATA 2 DATA 1 DC 12V REAR DATA1 REAR DATA2 DC 12V KEYBOARD CONTROLLER HTX-5000 그림 4. 기본시스템구성도 1. 제품시스템구성에있어그림 4 와같은방법으로구성할것을권장합니다. 2. 만약다른방법으로시스템을구성하고자한다면제조사및설치전문기관과상의하여진행할것을권장합니다. 3. 제품컨트롤지원이가능한 DVR 의종류에따라서 HTX-5000 컨트롤러가필요없을수도있습니다. -749- -
케이블구성 BNC Alram In/Out Put POWER (AC 100V ~ 240V) RS-485 Data+, - 2m ± 0.3m 그림 5. 케이블구성 케이블구성확인 Wire Color Function Description Brown Sky Blue Green 입력전압 (AC 100V ~ 240V) L1 N GND Red Orange Yellow Green Black Black Red Yellow White Black (Coaxial cable) Blue stripe White stripe 알랍입력알람출력 A 알람출력 B 비디오 Control Data Alarm 1 Alarm 2 Alarm 3 Alarm 4 GND NO A COM A NO B COM B BNC Cable RS485 Data + RS485 Data - -850- -
KOR 제품특징및중요기능 본제품은내압고해상도의 Super HAD CCD를채용한줌카메라를내장하고있는방폭카메라이며, IECEx 및 ATEX 방폭인증을취득하여위험지역 (Zone1, 2) 에서문제없이사용될수있도록견고하게디자인및제작되었습니다. 그리고광학줌 36배율의렌즈가내장된카메라가장착되어원거리의사물도감시하기에용이하며야간에도사물을식별할수있도록 Night Shot 기능이내장되어있습니다. 또한사용자는화면의메뉴와바로가기메뉴로프로그램을쉽게설정할수있습니다. 시스템정보는프로토콜, 보드레이트, 카메라드라이버의하드웨어및소프트웨어버전을표시하 여문제발생시, 해결에도움을줍니다. 방폭등급 : Ex d IIC T6 (IECEx, ATEX, CE, FCC, KC) 재질 : SUS316, 표면전해연마 방수방진등급 : IP67 해상도 650TVL, 광학 36배줌오토포커스렌즈장착카메라모듈채용 최고 60º/sec의속도로 360º 연속회전및가능한팬, 틸트기능 틸트동작시자동으로화면전환기능 다양한동작기능 - Home Function - 128개저장가능한프리셋옵션가능 - 8개저장가능한오토스캔가능 - 4개저장가능한투어및패턴기능가능 와이퍼기능내장 4개의알람입력과 2개의알람출력 워터젯 (EXWJ400) 적용하여워셔기능확장적용가능 무게약 30kg -951- -
간단한기능조작가이드 * 이기능은기본값인 S2/S2e 프로토콜에서 HTX-5000 컨트롤러에맞추어져있습니다. 기능 조작및순서 결 과 비고 팬 / 틸트 배율 / 초점 / 조리개 1 1 누르고 (CAM) 버튼을연속해서누릅니다. 2 조이스틱을상. 하. 좌. 우로움직입니다. 1 조이스틱을오른쪽으로돌립니다. 2 조이스틱을오른쪽으로돌립니다. -. 컨트롤러를 ID 01번으로설정합니다.. 만약 ID를 2번으로설정하기위해서는 2 를누르고을누릅니다. -. 영상이상. 하. 좌. 우로움직이는것을확인할수있습니다. -. 확대 -. 축소 3 다. 4 다. 버튼으로조절합니 버튼으로조절합니 -. 초점거리가가깝고멀게변경됩니다. -. 조리개가열리고닫힙니다. 와이퍼동작 1 (On) 버튼을누르거나을누른후연속해서 (On) 버튼을누릅니다. 단, Pelco프로토콜에서는 86+ ( 프리셋 ) 버튼을누릅니다. 2 -. 와이퍼가동작합니다. 우천시가아닌경우, 1 시간이상연속적인와이퍼동작은피해주십시오. 2 (Off) 버튼을누르거나 2 을누른후연속해서 (Off) 버튼을누릅니다. 단, Pelco프로토콜에서는 79+ ( 프리셋 ) 버튼을누릅니다. -. 와이퍼가동작을멈춤니다. 워터젯 ( 옵션 ) 1 초기물분사노즐위치를셋팅한다. -. 팬 / 틸트를이동하여카메라윈도우가노즐을향하는위치에놓고, 이위치를프리셋 59 번에저장합니다. - 워터젯을동작시키면불분사를위해미리저장된 59 번위치로팬 / 틸트가이동됨. 물통에물이항시있는지주기적으로확인. 4 2 버튼을누른뒤 (On) 버튼을누른다. - 워터젯이동작한다. 단, Pelco 프로토콜에서는 88+ ( 프리셋 ) 버튼을누릅니다. -10 52 -
KOR 간단한기능조작가이드 * 이기능은기본값인 S2/S2e 프로토콜에서 HTX-5000 컨트롤러에맞추어져있습니다. 기능 조작및순서 결 과 비고 메뉴 1 (Menu) 버튼을누릅니다. 단,Pelco 프로토콜인경우에는,95+ ( 프리셋 ) 버튼을누룹니다. -. 카메라메뉴를화면에띄웁니다. Preset Mapping: (Pelco 프로토콜시,) 2 조이시틱을이용하여상. 하. 좌. 우로항목을이동합니다. 3 (Menu) 버튼또는 (Enter) 버튼을누릅니다. 단, Pelco 프로토콜인경우에는,95 또는 96 + ( 프리셋 ) 버튼을누룹니다. -. 항목을상. 하. 좌. 우로이동합니다. -. 설정값을저장하거나, 변경합니다. Menu = 95+Preset Enter = 94+Preset ESC = 96+Preset 프리셋 1 프리셋설정저장 -. 1 부터 1 2 8 중에하나의번호를선택후버튼을누른후 (Shift) 와 (preset) 버튼을연속해서누릅니다. -.01 부터 128 개의번호중에선택한번호에설정위치가저장됩니다. Preset Mapping: (Pelco 프로토콜시,) 1~59+ 프리셋으로동작합니다. 2 프리셋동작 -. 설정위치가저장된번호를누른후 (preset) 을누릅니다. -. 저장된위치를불러옵니다. 스캔 1 스캔버튼을눌러세팅합니다. (Pelco 프로토콜시, 60+ 프리셋 ) -.01 부터 8 개의번호중에선택한번호에설정위치가저장됩니다. Preset Mapping: (Pelco 프로토콜시,) 2 스캔동작 -. 설정위치가저장된번호를누른후 (Scan) 을누릅니다. -. 설정된값에따라동작합니다. 61~68+ 프리셋으로 1~8 에저장된 Scan 동작을합니다. 투어 1 투어버튼을눌러세팅합니다. (Pelco 프로토콜시, 70+ 프리셋 ) -.01 부터 4 개의번호중에선택한번호에설정위치가저장됩니다. Preset Mapping: (Pelco 프로토콜시,) 2 투어동작 -. 설정위치가저장된번호를누른후 (Tour) 을누릅니다. -. 설정된값에따라동작합니다. 71~74+ 프리셋으로 1~4 에저장된 Scan 동작을합니다. 패턴 1 패턴버튼을눌러세팅합니다. ~ (Pelco 프로토콜시, 80+ 프리셋 ) -.01 부터 4 개의번호중에선택한번호에설정위치가저장됩니다. Preset Mapping: (Pelco 프로토콜시,) 2패턴동작 -. 설정위치가저장된번호를누른후 (pattern) 을누릅니다. ~ -. 설정된값에따라동작합니다. 81~84+ 프리셋으로 1~4 에저장된 Scan 동작을합니다. -11 53 -
프로그램및동작 프로그래밍 ( 수정 ) 모드에서조이스틱사용의정리 * 이기능은기본값인 S2/S2e 프로토콜에서 HTX-5000 컨트롤러에맞추어져있습니다. 메뉴에서버튼이나조이스틱의동작 Joystick 좌우로움직임 Joystick 위 / 아래로움직임 Joystick down Zoom 핸들을돌림 ESC 버튼을누름 Home 또는 Off 버튼을누름 기능 하위메뉴항목으로가기명령을실행하기 ( 나가기 ) 값을변환하기메뉴항목을탐색하기 메뉴항목을탐색하기 Finish editing title. 값을변경하기 ( 증가 / 감소 ) 제목수정모드들어가기 변경사항없이메뉴나가기 데이타의삭제혹은동작의해제 카메라세팅 ( 카메라 ID, 보레이트, 프로토콜 ) NEXPTZ 카메라는반드시설치전, 연결하려는장비와연동이되는지확인하여통신설정이되어야합니다. 통신을위한설정에는카메라 ID, 보레이트. 프로토콜이포함되어있습니다. 초기통신설정을하기위해서는, 제품에함께포함되어있는리모컨을이용하여설정할수있습니다. 이리모컨은설정된통신값과관계없이메뉴에진입하여연결되는장비와연동되도록통신설정값변경이가능합니다. 리모컨을사용할시, 제품전면윈도우를향하여작동하는것이제어에용이합니다. 화면에나타나는메뉴진입순서는다음과같습니다. MENU Communication Select CAMERA ID / BAUDRATE / PROTOCOL -12 54 -
KOR MENU TREE 프로그램및동작 1. FUNCTIONS 1.1 HOME FUNCTION (MENU Functions Home) 1.2 PRESET (MENU Functions Preset or Shortcut: PRST) 1.3 SCAN (MENU Functions Scan or Shortcut: SCAN) 1.4 TOUR (MENU Functions Tour or Shortcut: TOUR) 1.5 PATTERN (MENU Function Pattern or Shortcut: PTRN) 1.6 EXIT 2. ALARM 2.1 ALARM SETUP 2.2 SAVE AND EXIT 3. SCREEN 3.1 PRIVACY ZONE (MENU Screen Privacy Zone) 3.2 NORTH DIRECTION (MENU Screen North Direction) 3.3 ZONE TITLE (MENU Screen Zone Title) 3.4 CAMERA TITLE (MENU Screen Camera Title) 3.5 OSD DISPLAY (MENU Screen OSD Display) 3.6 EXIT 4. CAMERA 4.1 FOCUS CONTROL (MENU Camera Focus Control) 4.2 WB CONTROL (white balance) (MENU Camera WB Control) 4.3 AE CONTROL (auto exposure) (MENU Camera AE Control) 4.4 BLC/WDR SETUP (MENU Cemera BLC/WDR Setup) 4.5 SHARPNESS (MENU Camera Sharpness) 4.6 DIGITAL ZOOM (MENU Camera Digital zoom) 4.7 NIGHT SHOT (MENU Camera Night Shot) 4.8 CAMERA DEFAULT (MENU Camera Camera Default) 4.9 SAVE AND EXIT 5. SETUP 5.1 INSTALLATION (MENU Setup Installation) 5.2 SPEED (MENU Setup Speed) 5.3 PANNING RANGE (MENU Setup Panning Range) 5.4 CALIBRATION (MENU Setup Calibration) 5.5 FACTORY DEFAULT (MENU Setup Factory default) 5.6 ERASE DATA (MENU Setup Erase data) 5.7 SYSTEM INFORMATION (MENU Setup System Information) 5.8 SAVE AND EXIT 6. PASS WORD 6.1 ENABLE PASSWORD (MENU Password Enable Password) 6.2 EDIT PASSWAORD (MENU Password Edit Password) 6.3 SAVE AND EXIT 7. COMMUNICATION 7.1 EXPTZ ID (MENU Communication EXPTZ ID) 7.2 BAUDRATE (MENU Communication Baudrate) 7.3 PROTOCOL (MENU Communication Protocol) 7.4 SAVE AND EXIT 8. RUN FUNCTION 8.1 FUNCTION 8.2 NUMBER 8.3 RUN 8.4 EXIT -13 55 -
프로그램및동작 1. FUNCTION 키보드컨트롤러에있는 MENU 버튼을누르면다음과같이 On-screen 메인메뉴가모니터에나타납니다. Main Menu Function Alarm Screen Camera Setup Password Communication Run Function Exit FUNCTION 항목에커서가위치시키고, 조이스틱을오른쪽으로눌러서 FUNCTION 메뉴로들어갑니다. Function Home Function Preset Scan Tour Pattern EXIT 1.1 HOME FUNCTION (MENU =>FUNCTION => HOME FUNCTION) HOME FUNCTION 항목을선택하고, HOME FUNCTION 설정하기위해아래화면처럼합니다. Home Function Function : Tour Number : --- Time : 010 SEC Operation : DISABLE Save And Exit Function : Tour/ Preset/ Scan Number : - - - Time : 10~240 Seconds Operation : ENABLE/ DISABLE -14 56 -
KOR 프로그램및동작 HOME 기능은저장된프리셋이나투어, 패턴, 스캔같은기능을불러옵니다. HOME 기능의프로그램방법은아래를참조하세요. 1. No. and CAM 를눌러카메라번호를선택합니다. 2. 모니터에메인메뉴를표시하기위해 MENU를누릅니다. 3. FUNCTION 오른쪽으로 Joystick를이동시킵니다. 4. Joystick 를오른쪽으로움직여 Home Function메뉴에들어갑니다. 5. Joystick을좌 / 우 ( 시계방향이나반시계방향 ) 로돌려프리셋, 스캔, 패턴, 투어기능을설정합니다. 6. Joystick 을아래로이동시키고시계방향이나반시계방향으로돌려서 ( 좌우로움직이거나 ) Function Number를선택합니다. 실행할수있는 Function은스크롤될것입니다. 프로그램되지않은 Function을선택했다면, 변화가없을것입니다. 그럴경우, 설정을먼저해주십시요 7. Joystick 을아래로움직여 TIME에위치시키고, Joystick 을좌 / 우로움직여 ( 시계방향이나반시계방향으로돌리거나 ) 동작시간을설정합니다.(10~240초) 8. Joystick 을아래로내려서 OPERATION 에위치시키고, Joystick을좌 / 우로움직여 ( 시계방향이나반시계방향으로돌리거나 ) 동작상태를 Enable이나 Disable으로선택하십시오. 1.2 PRESET (MENU =>FUNCTION => PRESET ; Short cut : Preset) PRESET 은팬, 틸트, 줌, 포커스, 아이리스데이터를포함한위치데이터를저장합니다. 저장이되면, 컨트롤러에서 0 ~9 숫자의조합과 Preset 버튼을눌러서자동적으로프리셋위치를불러올수있습니다. 또한, 프리셋은알람기능을설정할수있고, 돔카메라에대한 HOME 위치를지정할수도있습니다. PRESET 항목에커서를위치시키고, PRESET 메뉴에들어가기위해조이스틱을좌 / 우로움직입니다. Function Home Function Preset Scan Tour Pattern EXIT -15 57 -
프로그램및동작 이곳에는 16 페이지의프리셋프로그래밍메뉴가있습니다. 각페이지는 8 개의 PRESET 을설정할수있습니다. PREV NEXT 에커서를위치시키고, Joystick 을좌 / 우로움직이면 PRESET 메뉴페이지가스크롤됩니다 PRESET 01/16 NO. F I B TITLE 001 A A F xxxxxxxxxxxxxxxx 002 M M O ---------------- 003 - - - ---------------- 004 - - - ---------------- 005 - - - ---------------- 006 - - - ---------------- 007 - - - ---------------- 008 - - - ---------------- PREV NEXT SAVE AND EXIT F : FOCUS I : IRIS B : BLC X : 16 문자입력가능 - : 설정안됨 : 현재커서위치 F : A( 자동포커스조절 )/ M( 수동포커스조절 ) I : A( 자동조리개 )/ M( 수동조리개 ) B : F( 역광해제 )/ O( 역광설정 )/ W(WDR) PRESET 기능의프로그램방법은아래를참조하세요. 1. 0 ~9 와 CAM. 눌러서카메라번호를선택합니다. 2. PRESET 메뉴를들어가기위해 Preset 버튼을누르면바로들어갑니다. ( MENU FUNCTION PRESET) 3. Joystick 을이용하여비어있는 PRESET 을선택합니다. 만약, 선택된위치가비어있지않다면, Preset 버튼을누르면저장되어있는 PRESET 위치로이동됩니다. 4. 비어있는 PRESET 을선택하고, Joystick 을돌려서카메라를조정하여원하는위치를촬상합니다. Position Pan : 000.0 Tilt : 000.0 Select Position Press Focus To Save -16 58 -
KOR 프로그램및동작 5. 원하는위치를찾은후 Near, Far 버튼을누릅니다. 선택된프리셋필드는 A A F 로채워질것입니다. 줌핸들을사용해각각의 Focus/ Iris /BLC 모드를선택합니다. 6. Joystick 을사용해서 PRESET 에대한타이틀을입력합니다. ( 시계 / 반시계방향으로돌리면알파벳이스크롤되고, 핸들을좌 / 우로움직이면다음글자나이전글자를입력할수있습니다.) 7. 타이틀입력이끝났으면, SAVE AND EXIT 메뉴를선택하고, Joystick 을좌 / 우움직여저장후종료합니다. 8. 프리셋의이전 / 다음페이지를선택하기위해 PREV NEXT 에커서를위치시킵니다. Joystick 을좌 / 우로조정하여페이지를스크롤시킵니다. 9. 2 에서 8 까지의단계를반복하면서원하는 PRESET 위치를저장합니다. 10. SAVE AND EXIT 메뉴를선택하고, Joystick 을좌 / 우움직여저장후종료합니다. ESC 버튼을누르면저장하지않고 PRESET 메뉴를마칩니다. 참고 : 저장된 PRESET 데이터를지우려면, 지우려는위치에서 Home 이나 OFF 버튼을누릅니다. < PRESET 단축키사용하기 > 원하는위치를촬상하고 ( 카메라의방향, 줌위치, 초점 ), 원하는 PRESET 번호 (1~128) 를누르고, Shift, Preset 버튼을순서대로누릅니다. 선택한번호의 PRESET 으로현재데이터가저장됩니다. 단, 이때입력한 PRESET 번호에저장된데이터가없어야합니다. 만약데이터가이미저장되어있다면, PRESET EXISTING 이라는경고메시지가나타납니다. 예 : 1, 0 + Shift + Preset 버튼을순서대로누르면, 현재촬상되는위치가 PRESET 10 번으로저장됩니다. 이때포커스모드, 아이리스모드는자동모드로, Dwell 시간은 3 초로설정됩니다. -17 59 -
프로그램및동작 1.3 SCAN (MENU =>Function => Scan ; Short cut : SCAN) Scan 기능의미리설정된좌측지점에서우측지점까지사용자가설정한속도로연속감시할수있는기능입니다. Scan 은 8 개까지설정가능합니다. Scan Menu 01/08 Scan 01 : AUTOSCAN01 Speed : 1~8 Start : 127.1, 027.0 zoom End : 157.7, 080.7 zoom Dir : CCW (PAN:000.0) Swap : OFF Save And Exit SCAN01 : AUTOSCAN01 ~ SCAN08: AUTOSCAN08 SPEED(MODE) : 1/ 2 / 3/ 4/ 5/ 6/ 7/ 8 1: SLOWER 8 FASTER 다음순서에따라 Scan 기능을설정합니다. 1.Scan 메뉴로바로들어가려면 SCAN 버튼을누릅니다. ( 또는 MENU FUNCTION SCAN). 2.Joystick 을좌 / 우로움직여원하는 Scan 번호를선택합니다. 3.Joystick 을좌우로움직이면타이틀을입력할수있습니다. Joystick 을돌리면알파벳이순서대로나타나고, 좌 / 우로움직이면다음글자를입력할수있습니다. Joystick 을아래로움직여 " SAVE AND EXIT 를선택하면타이틀입력모드가완료됩니다. 4. Speed 를선택하기위해 Joystick 을아래로움직입니다. 시계방향이나반시계방향으로돌리고, Scan 속도를선택하기위해 Joystick 을좌 / 우로움직여속도를설정합니다. 5. Joystick 을아래로움직여 START 를선택합니다. Joystick 을이용해시작점을결정합니다. 현재 panning 위치가표시됩니다. 시작점선택을마치려면 Focus 버튼을누릅니다. 6. Joystick 을아래로움직여 END 를선택합니다. Joystick 을움직여끝점을선택합니다. 끝점선택을마치려면 Focus 버튼을누릅니다. 7. Joystick 을아래로움직여 Dir ( 방향 ) 을선택합니다. Joystick 을이용해회전방향을시계방향또는시계반대방향으로설정합니다. 8. Joystick 을아래로움직여 SWAP 을선택합니다. 스왑 (SWAP) 은시작지점과끝점을서로바꾸고자할때사용됩니다 9. Joystick 을오른쪽으로움직여 SAVE AND EXIT 메뉴를선택합니다. 저장하지않고설정을마치려면 ESC 버튼을누릅니다. 참고 : 저장된 PRESET 데이터를지우려면, 지우려는위치에서 Home 이나 OFF 버튼을누릅니다. -18 60 -
KOR 프로그램및동작 1.3 TOUR (MENU => Function => Tour ; Short cut : TOUR) 투어 (Tour) 프로그램은 4 개까지입력할수있습니다. 각투어 (Tour) 에는 32 개의프리셋 (Preset), 또는패턴 (Pattern), 스캔 (Scan), 그리고또다른투어 (Tour) 로구성되어있습니다. 또다른투어를사용하면하나의투어에 56 개이상의프로그램을입력할수있습니다. 그러나투어에서다른투어에의해투어를불러오게되면 2 단계투어는무시됩니다. 이것은아래의예로가장잘표현될수있습니다. 만약 Tour 01 : Preset 02, Preset 03,Tour 02, Tour 03 Tour 02 : Preset 05, Preset 06, Tour 04, Preset 05 Tour 03 : Preset 07, Pattern01 Tour 04 : Preset 08. Preset 05, Pattern01 설정이되었으면, Tour1 은다음과같이실행됩니다. Preset 02 Preset 03 Preset 05 Preset 06 Preset 05 Preset 07 Pattern 01... ( 반복 ) --Tour 01 에서 Tour 02 에있는 Tour 04 는무시됩니다. Tour 02 는다음과같이실행됩니다. Preset 05 Preset 06 Preset 08 Preset 05 Pattern 01 Preset 05 ( 반복 ) (Tour4 는 Tour2 에서직접불려질때만동작됩니다.) TOUR 01:xxxxxxxxxxxx 01/04 FUNC NO S DW TITLE PRST 001 S 03 ---------------- SCAN 016 S 03 ---------------- TOUR 008 S 03 ---------------- ---- --- - -- ---------------- ---- --- - -- ---------------- ---- --- - -- ---------------- ---- --- - -- ---------------- PREV NEXT SAVE AND EXIT xxxxx : 16 문자입력 - - - : 저장된데이터없음 Speed : Fast (Normal)/ Slow DWell : 01-99 Sec PRST : Preset 1~128 PTRN : Preset 1~4 SCAN : SCAN 1~8 TOUR : TOUR 2~4-19 61 -
프로그램및동작 다음순서에따라 Tour 기능을설정합니다. 1. 투어메뉴로바로들어가려면 Tour 버튼을누릅니다.( 혹은 MENU FUNCTION TOUR) 2. Joystick 의위나아래로움직여, 빈위치를선택합니다. 3.Joystick 을좌우로움직여변경모드로들어가서 Preset 버튼을누르면 ( 혹은 Tour, Scan, Pattern) 저장된프리셋시점을불러올수있으며, 번호영역으로이동하고, Preset 버튼을누르면저장된프리셋시점으로이동할수있습니다. 4. 저장된프리셋을 Tour 에추가하려면, Joystick 을돌리거나 Zoom 버튼을누릅니다. ( 프로그램된프리셋은스크롤됩니다 ). 저장된프리셋을 Tour 에서삭제하려면, HOME 버튼을누릅니다. 저장된위치가없다는표시 (-) 가나타납니다. 그리고프로그램된위치를덮어쓸수있습니다 5. 각각원하는위치로위 2 단계부터 4 까지반복하십시오. 각각의타이틀은라인의꼭대기에나타날것입니다. 6.32 개의프리셋, Tours, Patterns Scans 까지 Tour 에선택될수있습니다. 프로그램된다른투어를불러들여서확장할수도있습니다. Tour 메뉴의다른페이지를선택하려면커서가맨윗줄 ( TOUR 01 ) 에있을때 Joystick 을돌립니다. 7. 선택한투어의타이틀을입력하려면, 커서가맨윗줄 ( TOUR 1 ) 에있을때 Joystick 을돌립니다. 핸들을돌리면알파벳이스크롤됩니다. 핸들을좌우로움직이면이전혹은이후의문자가선택됩니다. 8.Joystick 을오른쪽으로움직여 SAVE AND EXIT 를선택합니다. ESC 를누르면저장하지않고메뉴를빠져나옵니다. 참고 : 저장된 PRESET 데이터를지우려면, 지우려는위치에서 Home 이나 OFF 버튼을누릅니다. -20 62 -
KOR 프로그램및동작 1.4 PATTERN (MENU => Function => Pattern ; Short cut : PATTERN) 패턴 (Pattern) 은사용자의카메라제어를그대로 240 초동안저장합니다. 총 4 개의패턴이가능하고, No.+ Pattern 버튼을누르면저장된데이터를재생할수있습니다. Pattern Setup NO TILTIE SEC O1 : PATTERN1 000 O2 : PATTERN2 041 O3 : PATTERN3 010 O4 : PATTERN4 020 TOTAL: 071 Save And Exit 다음순서에따라 Pattern 기능을설정합니다. 1. 0 ~9 와 CAM. 눌러서카메라번호를선택합니다. 2. Pattern 키를누릅니다. ( 또는 MENU Function Pattern) 3.Joystick 을상하로움직여데이터가저장되어있지않는패턴번호를선택합니다. 마지막열이 000 이아니라면, 데이터가저장되어있는패턴입니다. 그러나데이터를덮어씌우는것도가능합니다. 4.Joystick 을돌려서패턴설정화면에들어갑니다. Joystick 을이용해물체를촬상하거나줌동작을합니다. 사용자의모든카메라제어는자동저장됩니다. 원하는패턴을저장할때까지이동작을반복할수있습니다. (PTZ 컨트롤을시작하려면줌버튼을누르거나줌핸들을돌리고, 멈추려면 Focus 버튼을누릅니다.) 5."SAVE AND EXIT 메뉴를선택하고, Joystick 을오른쪽으로움직이면데이터가저장됩니다. 6.Joystick 을좌우로움직여선택한패턴의타이틀을입력할수있습니다. 핸들을시계방향 / 반시계방향으로돌리면알파벳문자가스크롤됩니다. 핸들을좌 / 우로움직여이전 / 이후문자를입력할수있습니다. 7.ESC 버튼을누르면저장하지않고, 메뉴에서빠져나와이전모드로이동합니다. 프로그램된위치에서 HOME 이나 OFF 버튼을누르면, 저장된패턴은삭제됩니다. 주의 : 저장시간이 240 초가되면, 자동적으로메뉴상태로빠져나옵니다. PATTERN 기능은 FAN 과 TILT 기능만지원이됩니다. -21 63 -
프로그램및동작 2. ALARM Main Menu Function Alarm Screen Camera Setup Password Communication Run Function Exit 카메라의 ALARM 프로그래밍하기위해메인메뉴의 ALARM 메뉴에커서를위치시키고, 조이스틱을오른쪽으로움직입니다. Alarm Setup No Fun Pri In Out Hld Latch 01 001 3 OFF OFF 001 OFF 02 002 3 OFF OFF 001 OFF 03 003 3 OFF OFF 001 OFF 04 004 3 OFF OFF 001 OFF Save And Exit No Fun : 알람 (Alarm) 입력번호 : 알람발생시호출되는프리셋번호, 우선순위를 1~8 로설정하면 Preset, Pattern, Scan 이가능합니다. ( 바로가기버튼사용해기능설정가능 ) 우선순위를 0 으로설정하면,Pattern(Pxx), Tour(Txx), Scan(Sxx) 이가능합니다. 주의 : Tour 는우선순위가 0 일때만설정가능합니다. Pri(Priority) : 우선순위숫자가작을수록먼저처리됩니다. 우선순위가같으면순차적으로처리됩니다.. In : NO/NC - normally open /Closed, OFF ignore Out : RO1 - Relay out 1, RO2 Relay out2 OFF - No output. Hld(Hold) Latch : 알람을유지하는시간 (01 to 255 seconds) : ON - 해제된알람을포함한모든알람표시, OFF - 현재동작중인알람만표시 9 레벨의우선순위중에서, 0 PRI 설정되어있는기능의우선순위가가장높습니다. 0 우선순위는스캔, 패턴, 투어기능이설정될수있습니다. 0 우선순위의알람경보가발생중이면, 그동작이끝날때까지다른알람은반응하지않습니다. -22 64 -
KOR 프로그램및동작 1. MENU 버튼을누르면모니터에메인메뉴가나타납니다. Joystick 을이용해알람메뉴를선택하고, 오른쪽으로움직여세부메뉴로들어갑니다. 2. 조이스틱을상 / 하로움직이면, 알람입력번호가선택됩니다. 설정하려는열을선택합니다. 선택된위치는하이라이트됩니다. 3. 프리셋, 입력의상태 (NC/NO/OFF), 출력의상태 (RO1/RO2/OFF) 를선택하려면조이스틱을돌립니다. 4. 프리셋번호를증가 / 감소하거나, 상태 / 출력번호를바꾸려면, Joystick 을시계방향 / 반시계방향으로돌립니다. 프리셋의경우, 프리셋번호가스크롤됩니다. 5. 조이스틱을상하로움직여 SAVE AND EXIT 메뉴를선택합니다. 조이스틱을오른쪽으로움직이면데이터를저장하고메뉴를종료합니다. ESC 를누르면저장하지않고메뉴를종료합니다. 3. SCREEN 키보드컨트롤러에있는 MENU 버튼을누르면다음과같이메인메뉴가모니터에나타납니다. Main Menu Function Alarm Screen Camera Setup Password Communication Run Function Exit 조이스틱을상하로움직여 SCREEN 항목에커서를위치시키고, 조이스틱을오른쪽으로움직여 SCREEN 세부메뉴로들어갑니다. Screen Setup Privacy Zone North Direction Zone Title Camera Title OSD Display Exit -23 65 -
프로그램및동작 3.1 PRIVACY ZONE (MENU => Screen => Privacy Zone) PRIVACY ZONE 항목에커서를위치시키고, 조이스틱을오른쪽으로움직여세부메뉴로들어갑니다. Screen Setup Privacy Zone North Direction Zone Title Camera Title OSD Display Exit 이기능은사적인이유로제한된영역을가려줍니다. 촬상을원하지않는부분을막아주며, 8 곳까지가능합니다. Privacy Zone Setup NO TITLE Method Color 01 xxxxxxxxxxxxxxxx MASK BLU 02 xxxxxxxxxxxxxxxx V.OFF BLU 03 ---- 04 ---- 05 ---- 06 ---- 07 ---- 08 ---- Save And Exit Method : BLOCK / V.OFF / MOSA / None Color :BLUE/SKY/RED/YELLOW/CYAN/GREEN/MAGNET/WHITE/GRAY 1. MENU 버튼을누르면모니터에메인메뉴가나타납니다. 조이스틱을상하로움직여 Privacy Zone 메뉴를선택하고, 조이스틱을오른쪽으로움직여세부메뉴를선택합니다. 2. 조이스틱을상하로움직여 privacy zone 번호를선택합니다. 3. zone 의이름을입력하려면, 핸들을시계 / 반시계방향으로돌립니다. 핸들을돌려알파벳을선택합니다. 조이스틱을오른쪽으로움직이면, 다음문자를입력할수있습니다. Joystick 을아래로내려 Save and Exit 를선택하면타이틀입력이완료됩니다. -24 66 -
KOR 프로그램및동작 4. 숨길영역 (Marked privacy area) 을선택하려면, Joystick 을돌려조정화면으로들어갑니다. 조이스틱을사용하여방향이나줌을조정하고원하는위치를촬상합니다. 포커스버튼을누르면, Method 가 ON 으로바뀝니다. 5. 현재저장되어있는데이터를덮어쓸수있습니다. Home 버튼을누르면 privacy zone 은삭제됩니다. 또한 Joystick 을좌 / 우로움직이면저장된영역을설정 / 해제할수있습니다. 6. 설정된 PZM 영역을마스크하는컬러를설정합니다. 7. Joystick 을상하로움직여 SAVE AND EXIT 를선택합니다. Joystick 을오른쪽으로움직이면데이터를저장하고메뉴를종료합니다. ESC 버튼을누르면저장하지않고메뉴를빠져나옵니다. HOME 버튼을누르면저장된 PRIVACY ZONE 이삭제됩니다. 3.2 NORTH DIRECTION (MENU => Screen => North Direction) NORTH DIRECTION 옵션을선택하기위해조이스틱을오른쪽으로움직이십시오. North Direction Position : ---.- Save And Exit 조이스틱을이용하여지정하려는방향으로이동하여 N(north) 방향을설정합니다. 그리고저장하면현재팬위치가모니터상에표시됩니다. 90 도마다 E(East), S(South), W(West) 로변경이됩니다. 만약, 방향표시를자주 ON/OFF 할경우, N(North) 을프리셋으로설정하는것을추천합니다. 3.3 ZONE TITLE (MENU => Screen => Zone Title) START( 시작점 ) 과 END( 끝점 ) 사이에저장된각도에이름을입력합니다. Zone Title 01/03 No Title Start End 01 WINDOW 123.4 345.6 02 ----- ----- 03 ----- ----- 04 ----- ----- 05 ----- ----- 06 ----- ----- PREV NEXT Save And Exit -25 67 -
프로그램및동작 1. Zone title 메뉴를화면상에표시하기위해 MENU SCREEN ZONE TITLE 을누르십시오. 2. Joystick 을상하로움직여 zone number 를선택합니다. 핸들을좌우로움직이면서 Start, End, number 를설정합니다. 선택된열이하이라이트됩니다. 3. 영역이름을입력하려면, Title 을선택하고핸들을돌립니다. 핸들을돌려알파벳을선택합니다.Joystick 을오른쪽으로움직이면, 다음문자를입력할수있습니다. 조이스틱을아래로움직여 SAVE AND EXIT 를선택하면종료됩니다. 4. START, END 에서 Joystick 을돌려원하는위치를영역으로설정합니다. End 의각도는 Start 보다커야합니다. (Start < End). ( 혹은 PTZ 컨트롤을시작하기위해줌핸들을돌리거나, 줌버튼을누르십시오. 그리고, 컨트롤모드를나가기위해 Focus 버튼을누릅니다.) 5. Joystick 을오른쪽으로움직여 SAVE AND EXIT 를선택합니다. 조이스틱을오른쪽으로움직이면데이터를저장하고, 메뉴를빠져나옵니다. ESC 를누르면저장하지않고메뉴를종료합니다. 3.4 CAMERA TITLE (MENU => Screen => Camera Title) CAMERA TITLE 옵션을선택하기위해조이스틱을오른쪽으로움직이시오. Camera Title Setup Title : CAM No. Save And Exit 1. Camera title 에들어가기위하여 TITLE : CAM No. 에서조이스틱을돌립니다. 조이스틱을돌려알파벳을선택합니다. Joystick 을오른쪽으로움직이면, 다음문자를입력할수있습니다. Camera title 은최대 10 문자까지지원됩니다. Joystick 을아래로움직여 SAVE AND EXIT 를선택하면, 타이틀입력이종료됩니다. 2. Joystick 을오른쪽으로움직여 SAVE AND EXIT 를선택하면데이터를저장하고, 메뉴를빠져나옵니다. ESC 를누르면저장하지않고메뉴를종료합니다. -26 68 -
KOR 프로그램및동작 3.5 OSD DISPLAY (MENU => Screen => OSD Display) OSD Display Function Title : ON Camera Title : ON Zone Title : ON North Direction : OFF Camera Position : ON Camera ID : ON Zoom Magnification : ON Save And Exit 1. 조이스틱핸들을오른쪽으로움직이면 OSD 상의각기능들에대한표시여부를설정할수있습니다. 2. Joystick 을오른쪽으로움직여 SAVE AND EXIT 를선택하면데이터를저장하고, 메뉴를빠져나옵니다. ESC 를누르면저장하지않고메뉴를종료합니다 4. CAMERA 키보드컨트롤러에있는 MENU 버튼을누르면다음과같이메인메뉴가모니터에나타납니다. 조이스틱을상하로움직여 Camera 항목에커서를위치시키고, 조이스틱을오른쪽으로움직여 Camera 세부메뉴로들어갑니다. Main Menu Function Alarm Screen Camera Setup Password Communication Run Function Exit 주의 : 카메라에내장된카메라모듈에따라메뉴는달라질수있습니다. -27 69 -
프로그램및동작 Camera Menu Focus Control WB Control AE Control BLC/WDR Setup Sharpness : 6 (1~15) Digital Zoom : OFF/2x/4x/MAX Night Shot Camera Default Save And Exit 4.1 FOCUS CONTROL (MENU => Camera => Focus Control) Focus Setup Mode : MANUAL AF Sensitivity : NORMAL Exit Mode : MANUAL / AUTO AF Sensitivity : NORMAL / LOW 주의 : 자동초점모드를 24 시간연속사용하는것은피하십시오. 렌즈의수명을단축시킬수있습니다. 4.2 WB (white Balance) CONTROL (MENU => Camera => WB Control) WB Setup Mode : AUTO R.GAIN : N/A B.GAIN : N/A Exit Mode: AUTO / INDOOR / OUTDOOR / ONE PUSH / ATW / MANUAL MANUAL : Control of R and B Gain AUTO : Computes the white balance value output using color information from the entire screen automatically.(3000 to 7500 K) INDOOR : 3200 K base mode OUTDOOR : 5800 K base mode R.GAIN : 0~255 B.GAIN : 0~255 일반적으로 AUTO 모드를사용합니다. R.Gain / B.Gain 모드는오직 MANUAL 모드에서사용됩니다. -28 70 -
KOR 프로그램및동작 4.3 AE(Auto Exposure) CONTROL (MENU => Camera => AE Control) NEXPTZ camera 에따라화면이다를수있습니다. AE Setup Mode : FULL AUTO Slow Shutter : x10 Iris : Auto Gain : Auto Bright : 008 Shutter : Normal Exit Mode : FULL AUTO / MANUAL / IRIS PRIO / SHUTTER PRIO Slow Shutter : ON/OFF(AUTO mode only) Iris : OPEN / CLOSE / 01 / 02 / / 16 Gain : 0 / 2 / 4 / / 30 db Bright : 000 ~ 015 / NORMAL (008: Default) Shutter : 1/60(1/50), 1/100(1/120),1/250, 1/500, 1/1000, 1/2000, 1/4000, 1/10000, 1/20000, 1/50000. 1/100000 NOTE : Values in ( ) are for PAL Camera. 4.4 BLC/WDR SETUP (MENU => Camera => BLC/WDR Setup) 중심피사체와대비하여주변광이더밝은환경에서는중심피사체가어둡게보일수있습니다. 역광보정모드를설정하면중심피사체가밝아져식별이가능하게됩니다. BLC ON/ AUTO/ WDR 로설정가능합니다. BLC/WDR Setup BLC/WDR : OFF WDR Lever : 07 Exit BLC/WDR : OFF / BLC / WDR WDR LEVEL : N/A, 1 ~ 7 (WDR Mode) 4.5 SHARPNESS (MENU => Camera => Sharpness) Sharpness : 1~15 설정값을높일수록영상의윤곽선이두드러집니다. -29 71 -
프로그램및동작 4.6 DIGITAL ZOOM (MENU => Camera => Digital Zoom) Digital Zoom : OFF (Optical Zoom only) / 2x / 4x / MAX (16x) Camera Menu Focus Control WB Control AE Control BLC/WDR Setup Sharpness : 6 Digital Zoom : OFF Night Shot Camera Default Save And Exit 4.7 NIGHT SHOT (MENU => Camera => Night Shot) Night Shot Setup Mode Local Control Exit : AUTO : OFF NIGHT SHOT 기능은카메라의 IR 차단필터를제거하고카메라감도를높여줍니다. 나이트모드에서는자동으로흑백 (BLACK & WHITE) 모드로절환됩니다. Mode : MANUAL / AUTO AUTO 저조도에서카메라는자동적으로흑백모드로갑니다. MANUAL 카메라의 Night Shot 기능을개별적으로설정 / 해제야간모드의 ON/OFF 는 10+ON/ 10+OFF 키를눌러원격제어가능합니다. 4.8 CAMERA DEFAULT (MENU => Camera => Camera Default) 카메라의모든설정값들은공장초기값으로돌아갑니다.. Camera Default Are you sure?(yes/no) YES : ENTER KEY or MENU KEY NO : ESC KEY -30 72 -
KOR 프로그램및동작 5. SETUP Main Menu Function Alarm Screen Camera Setup Password Communication Run Function Exit Setup 항목에커서를위치시키고, 조이스틱을오른쪽으로움직여세부메뉴로들어갑니다. Setup Menu Installation : NORMAL Speed : FAST Panning Range Calibration Factory Default Erase Data System Information Save And Exit 5.1 INSTALLATION (MENU => Setup => Installation) 이기능은카메라를천정형으로설치했을경우에도카메라영상이정상적으로보여질수있도록해줍니다. NORMAL : 카메라가바닥면에설치되었을때설정합니다. CEILING : 카메라가천정에거꾸로설치되었을때설정합니다. 5.2 SPEED (MENU => Setup => Speed) FAST : 60 / sec (MAX) SLOW : 10 / sec MID : 30 / sec -31 73 -
프로그램및동작 5.3 PANNING RANGE (MENU => Setup => Panning Range) Panning Range RIGHT LIMIT : ---.- LEFT LIMIT : ---.- ENABLE : OFF SWAP RIGHT/LEFT Save And Exit 카메라가코너부분에설치되어좌우회전에물리적으로제약이있을경우, 이기능을이용하여좌우회전을제한할수있습니다. 5.4 CALIBRATION (MENU => Setup => Calibration) Calibration Origin Reset Origin Position Move Origin Offset : DISABLE Auto Calibration : OFF Save And Exit Origin Reset : 기본위치로조정합니다 Origin Position Move : 기본위치를오프셋만큼재설정합니다. Origin Offset : DISABLE / ENABLE Auto Calibration : 카메라가외부의충격이나진동에의해일정이상의좌표값이변화가발생하면자동으로오프셋을재설정하고, 원래위치로돌아갑니다. ( 단, PAN 오차 > 3, TILT오차 > 3 경우에동작.) 5.5 FACTORY DEFAULT (MENU => Setup => Factory Default) Factory Default Are you sure?(yes/no) YES : ENTER KEY or MENU KEY NO : ESC KEY 선택된카메라의모든데이터가공장초기값으로설정됩니다. -32 74 -
KOR 프로그램및동작 5.6 ERASE DATA (MENU => Setup => Erase Data) Erase Programmed DATA Are you sure?(yes/no) YES : ENTER KEY or MENU KEY NO : ESC KEY 선택된돔카메라의 EEPROM 에저장된모든데이터가지워집니다. 데이터를지우려면 MENU 또는 ENTER 버튼을누르고, 지우지않고나오려면 ESC 를누릅니다. Origin offset 값을제외한모든데이터가지워집니다. 5.7 SYSTEM INFORMATION (MENU => Setup => System Information) System Information Camera Type : xxxxxx H/W Version : V1.0 ROM Version : V1.2 Protocol : S2E Buadrate : 9600BPS Exit 서비스를요청할때사용할수있도록, 현재카메라의기본정보를표시합니다 6. PASSWORD Password Setup Enable Password : ON/OFF Edit Password : **** Save And Exit 네자리비밀번호를설정또는변경할수있습니다. 1. Joystick 핸들을오른쪽으로이동후위 / 아래또는회전하여 0~9 까지의숫자네자리를설정하고, 같은방법으로설정된네자리비밀번호를확인한다. 2. Joystick 을오른쪽으로움직여 SAVE AND EXIT 를선택하면데이터를저장하고, 메뉴를빠져나옵니다. ESC 를누르면저장하지않고메뉴를종료합니다. -33 75 -
프로그램및동작 7. COMMUNICATION Communication Setup EX PTZ ID : 0001 Baudrate : 9600 Protocol : AUTO Save And Exit 1. Joystick 을오른쪽으로이동하고, 상 / 하로움직여 EXPTZ ID 를선택할수있습니다. 2. Joystick 을오른쪽으로이동하고, 상 / 하로움직여 BARDRATE (2400/ 4800/ 9600/ 19200/ 38400) 선택할수있습니다. 3. Joystick 을오른쪽으로이동하고, 상 / 하로움직여프로토콜을선택할수있습니다. 4. Joystick 을오른쪽으로움직여 SAVE AND EXIT 를선택하면데이터를저장하고, 메뉴를빠져나옵니다. ESC 를누르면저장하지않고메뉴를종료합니다. 5. 제품포장에함께동봉되어있는무선컨트롤러를이용해초기통신을위해값을변경설정할수있습니다. ( 이때무선컨트롤러는프로토콜설정값과관계없이제품메뉴에진입하여설정값을변경할수있습니다.) 8. RUN FUNCTION Run Function Function : Number : Action Run Exit 1. 사용하는컨트롤러에사용하고자하는기능들을위한버튼이없을경우, 이기능을이용하여미리저장된기능을실행할수있습니다. 2. Joystick 으로기능을선택후 Run 에위치하여오른쪽으로이동하여실행시킵니다. -34 76 -
KOR 사양 General Mechanical & Electrical Spec Models NEXPTZ364NA NEXPTZ364PA Signal System NTSC PAL Ex. Class Certifications Front window Ex d IIC T6 IECEx, ATEX, CE, FCC, KC Fully tempered plate glass Material SUS 316 Protection Degree IP 67 Pan & Tilt Pan / Tilt Angle: 360 Continuous rotation Speed: 0.5 ~ 60 /sec (Manually, Proportional to Zoom, Vector Scan) 60 /sec Max (Preset) Auto Scan Preset Pattern Tour Alarm Control Input Voltage Power consumption 8 Scan Selectable 128 positions with focus 4 Pattern, 240 second 4 Tour Selectable Input: 4 Normal dry contacts (Selectable NC/NO) Output: 2 Normal relays 30VDC/1A max. (Normally Open) RS-485(Only Analog Type) 100-220 V~, 50/60Hz MAX 150W Operating Temperature -20 C ~ 60 C Weight Approx. 30 kg -35 77 -
사양 Camera Optical Models Spec NEXPTZ364NA NEXPTZ364PA Image Sensor 1/4" SONY Super HAD II (Double Scan) CCD Total pixels 1028(H) X 508(V) 1028(H) X 596(V) Scanning System 2:1 Interlace Scanning Frequency 15.734kHz(H),59.94Hz(V) 15.625kHz(H),50Hz(V) Sync. System Internal Resolution Max 700 TV lines in color @ HR 7 mode (750TV lines in B/W @ 7 mode) Min. illumination Color : 0.5lux, B/W : 0.2lux (Color DSS : 0.001lux, B/W DSS : 0.0001lux) S/N Ratio More than 50dB (AGC OFF) Lens Type X36 Day & Night Zoom Lens Lens Zoom Ratio Optical x36 times, Digital x16 times Lens Focal Length f = 3.4mm ~ 122.4mm Lens Aperture Ratio F1.6 (wide) ~ F4.5 (tele) -36 78 -
KOR 치수 Unit (mm) -37 79 -
추가구성품 Note: 이추가구성품은기본구성물에포함이안되어있으며, 필요시별도로구매해야하는품목입니다. 제품모델 1. NEXPTZ-PD: NEXPTZ 제품을받칠수있는브라켓으로, NEXPTZ 제품군에적용될수있으며, 제품설치시설치조건에따라응용될수있도록설계되었습니다. 2. NEXPTZ-WL: 벽부형설치브라켓으로 NEXPTZ 제품을벽면에설치할수있도록설계되었으며, 추가어댑터브라켓과혼용하여사용될수있습니다. 3. NEXPTZ-CN: 벽면모서리부분에 NEXPTZ 제품을설치할수있도록설계된어댑터브라켓으며, 벽부형브라켓과함께사용될수있습니다. 4. NEXPTZ-PL: 기둥에설치할수있도록설계된어댑터브라켓으로, 벽부형브라켓과함께제품을설치하는데이용할수있습니다. * 권장적용가능기둥지름은 Φ12cm ~ Φ25cm 입니다. 기본사양 NEXPTZ-PD NEXPTZ-WL NEXPTZ-CN NEXPTZ-PL Material SUS304 Polished SUS304 Polished SUS304 Polished SUS304 Polished Maximum Load 50kg 55kg 58kg 56kg Unit Weight 1.5kg 6.5kg 4.8kg 4.5kg -38 80 -
KOR Optional Accessories EXPTZ-PD Unit (mm) EXPTZ-WL Unit (mm) -39 81 -
Optional Accessories EXPTZ-CN Unit (mm) EXPTZ-PL Unit (mm) -40 82 -
KOR Remote Controller 1. POWER Power on/off. 2. NUMBERS Numeric keypads (0~9), 3. Camera Address (ID) Change camera ID. Number + CAM 4. WRITE PRESET(1~99) Saves camera picture s condition. Number + SAVE 5. PRESET(1~99) Recall preset. Number + PRESET 6. HOME Immediately calls Home function. 7. MENU OSD menu on. 8. DOWN / UP / LEFT / RIGHT Moves up/down in the menu. Moves left/right in the menu. Decreases/increases control. 9. ZOOM Zoom in/out 10. FOCUS Controls Focus. 11. IRIS Controls Iris. -41 83 -