3000 Series Art. 3171B Digital intercoms Bus line Local bell input Alarm input Service push button Handset

Size: px

Start display at page:

Download "3000 Series Art. 3171B Digital intercoms Bus line Local bell input Alarm input Service push button Handset"

준현 갈
6 years ago
Views:

1 Bus line Local bell input Alarm input Service push button Handset 2 Bell loudspeaker 3 Door opening push button 4 Service push button 5 Privacy -OFF (only Art. 312) Connection 8 way Dip-Switch (Phone ID) 8 Microphone volume control 9 Connection for optional relay board (JP2 Red = +) 10 Default = A Pos., B Pos. with opt. board 11 Option relay board (Art. 402) to activate an external bell 12 Electronic call tone volume control (3 levels) Fig. 1 - Art. 311B - Art. 312 Bus line DOOR OPEN LED power supply Local bell input Alarm input 1 Handset 2 Bell loudspeaker 3 Door opening push button 4 DOOR OPEN signalling LED 5 PRIVACY signalling LED Privacy -OFF push button Connection 8 8 way Dip-Switch (Phone ID) 9 3 way Dip-Switch (lenght of privacy time) 10 Microphone volume control 11 Connection for optional relay board 12 Default = A Pos., B Pos. with opt. board 13 Optional relay board (Art. 402) to activate an external bell 14 Electronic call tone volume control (3 levels) Fig. 2 - Art. 31 Art. 311B Installation instructions EN - V /0/15

2 DESCRIPTI The Art. 311 is a digital intercom based on the 2 Wire BUS, it includes a door-open button and a service button plus an electronic call tone with a 3 level volume control which can be adjusted by the user. Internally, the intercom, has an 8 way dip-switch to set the PHE ID, a terminal board with terminals for connection to the bus and other connections and a trimmer (VR1) to adjust the microphone volume. With the it is possible to connect up to 180 intercoms on the same system. If required it is possible to give the same address for a max. of 3 intercoms (for applications that require more units in the same apartment). The door-open push button on the Art. 311 is also call to concierge (if there is one on the system) push button, while the push button works on the terminals SW SW (Max 30Vac/dc 0,2A) of the terminal board. The Art. 312 is the same as the Art. 311 plus the privacy switch which activates the privacy mode (the user can t receive incoming calls). The Art. 31 is similar to the Art. 312 but in this case the privacy mode is activated by pressing the push button. It is signalled by the red led privacy on and its duration (except when the same push button is pressed again) depends on the 3 way dipswitch (housed inside the intercom) settings. The Art. 31 doesn t have the service push button but it has a green led door open to give the user a visual indication of whether the door is open or closed: to use this service, an additional wire is required from a door contact to the intercom. All 3 models of intercoms allow the connection of an optional relay board Art. 402, for the activation of an external sounder instead of the internal one: the board is housed inside the intercom, connected to the JP2 (red wire on side + ) and the JP1 jumper (normally on A position) must be moved to the B position. OPERATI IN STAND-BY MODE: The unit is ready to accept all the incoming calls; TO ANSWER A CALL AND OPEN THE DOOR: Pick the handset up and speak with the visitor (or concierge); press the Key button (if it is an external call) to open the door (an acoustic signal will be emitted and the door will be opened for the time programmed) or replace the handset to end the conversation; if the call is local (local bell), the call tone will have a different tonality from the main one. TO CALL THE CCIERGE UNIT (IF PRESENT AND LY VX VERSI): With the handset replaced, press the Key button and wait: the call is booked on the concierge and will be answered at the discretion of the operator; TO ACTIVATE THE SERVICE RELEVANT TO THE PUSH BUTT (EXCEPT THE ART. 31): Press the push button and the connected service will operate. Making some easy connections. It is possible to use this push button as an alarm push button: make a short between one of the SW terminal and the terminal and then connect the free SW terminal to the AL, terminal. The signal generated will be received by the concierge and/or by the Art. 512DR to activate an additional service. TO SELECT THE DESIRED MELODY (LY VERSIS ART. 311P, ART. 312P): 1. Keep pressed the Key button until (after about 10 seconds) the intercom play the active melody; at the end of melody play, the intercom emit a beep (end of play); 2. Listen the available melodies operating (press and release) the Key button after the beep at the end of play; 3. After the end of play beep if you don t press the Key button within 3 seconds, the last melody heard is selected. The selected melody will play how many times how is the number of rings value (3 or ) programmed. TO SWITCH THE PRIVACY MODE: For the Art. 312 put the switch, the small door over the switch will be RED; For the Art.31 press the push button marked as ; the red LED privacy on will illuminate. Art. 311B Installation instructions EN - V /0/15

3 PROGRAMMING Programming is made by setting the internal 8 way dip-switch to the positions shown on decimal/binary conversion table (pag. ) of this manual and the configuration of the number of rings (3 or ). For the Art. 31 it is necessary to set the internal 3 way dipswitch, to set the duration of the privacy mode, shown on the table below. SET THE NUMBER OF RINGS The standard setting is rings. To change the rings setting make as follow: Switch off the intercom disconnecting the L wire; Short-circuit terminals and LB ; Switch on the intercom connecting again L ; Remove the short-circuit as soon as the intercom emit the confirmation beeps:»» if are emitted two beep, rings are set to ;»» if is emitted one beep, rings are set to 3; Repeat again the operation if the number of rings set is not the required one. DIP SWITCH S OFF OFF OFF Unlimited OFF OFF 15 min OFF OFF 30 min OFF 1 hour OFF OFF 2 hours OFF 4 hours OFF 8 hours 1 hours TIME SEÑALES DE LA BORNES L BUS bus connection. LB Local bell input (ground signal). AL Alarm input (ground signal). The alarm generated by this input will be sent to the concierge (if present) and will be intercepted by the Art. 512DR if present and correctly configured. SW (only VX311, VX312) Service push button terminals SW (only VX311, VX312) LD (only VX31) Terminals for Door Open LED supply LD+ (only VX31) TECHNICAL SPECIFICATIS Addressing range: from 1 to 180 (BIN code) Working voltage: BUS line Voltage Stand-by absorption: about 0. ma Phone max. absorption: about 80mA Working temperature: C CUSTOMER SUPPORT All Countries: VIDEX ELECTRICS S.P.A. - technical@videx.it Tel: Fax: Art. 311B Installation instructions UK Customers: VIDEX SECURITY LTD Tech Line: Fax: The product is CE marked demonstrating its conformity and is for distribution within all member states of the EU with no restrictions. This product follows the provisions of the European Directives 2004/108/ECC (EMC); 200/95/ECC (LVD) and 93/8/ECC (CE marking) EN - V /0/15

4 Art. 311B Installation instructions EN - V /0/15

5 Art. 311B Installation instructions EN - V /0/15

6 Art. 311B Installation instructions EN - V /0/15

7 Addresses Table for dip-switch banks with position up 1/ = OFF = Art. 311B Installation instructions EN - V /0/15

8 Addresses Table for dip-switch banks with position up 2/ = OFF = Art. 311B Installation instructions EN - V /0/15

3600 Series Art Digital videophone for VX2200 Digital System ON SW1 SW2 ON SW3 ON Fig. 1 Fig. 2 DE

3600 Series Art Digital videophone for VX2200 Digital System ON SW1 SW2 ON SW3 ON Fig. 1 Fig. 2 DE 161 62 46 178 218 ON SW1 SW2 ON SW3 ON 1 2 3 4 5 678 1 2 3 4 1 2 3 Fig. 1 Fig. 2 DESCRIPTION Intelligent videophone for the VX2200 digital system incorporating a 3,5 full colour active matrix LCD monitor,