Contents 1. Product Code Information ----------------------- 3 2. Characteristics ----------------------- 10 3. Typical Characteristics Graph --------

Rev: 8.0 Product Family Data Sheet LM561B - 5630 Middle Power LED Introduction Features Beam Angle: 120 Precondition : JEDEC Level 2a Dimension : 5.6 x 3.0 x 0.8 mm ESD withstand Voltage : up to ± 5KV [HBM] SAMSUNG ELECTRONICS 95, Samsung2-Ro, Giheung-Gu, Yongin-City, Gyeonggi-Do 446-711, KOREA http://www.samsungled.com 1 / 48

Contents 1. Product Code Information ----------------------- 3 2. Characteristics ----------------------- 10 3. Typical Characteristics Graph ----------------------- 11 4. Outline Drawing & Dimension ----------------------- 17 5. Reliability Test Items & Conditions ----------------------- 18 6. Solder Conditions ----------------------- 19 7. Tape & Reel ----------------------- 20 8. Label Structure ----------------------- 22 9. Packing Structure ----------------------- 23 10. Precaution For Use ----------------------- 26 11. Hazard Substance Analysis Report ----------------------- 29 Revision History ----------------------- 51 http://www.samsungled.com 2 / 48

1. Product Code Information 1) Luminous Flux Bins (T s = 25 ) Nominal CCT Product Code Flux Rank Sorting Condition lm @65mA Flux Range (Φv, lm) SPMWH 541MD5WAW S1 S1 24.0 ~ 26.0 2700K SPMWH 541MD5WAW S2 S2 26.0 ~ 28.0 SPMWH 541MD5WAW S3 S3 28.0 ~ 30.0 SPMWH 541MD5WAV S1 S1 24.5 ~ 26.5 3000K SPMWH 541MD5WAV S2 S2 26.5 ~ 28.5 SPMWH 541MD5WAV S3 S3 28.5 ~ 30.5 SPMWH 541MD5WAU S1 S1 25.0 ~ 27.0 3500K SPMWH 541MD5WAU S2 S2 27.0 ~ 29.0 SPMWH 541MD5WAU S3 S3 29.0 ~ 31.0 SPMWH 541MD5WAT S1 S1 26.0 ~ 28.0 4000K SPMWH 541MD5WAT S2 S2 28.0 ~ 30.0 SPMWH 541MD5WAT S3 S3 30.0 ~ 32.0 SPMWH 541MD5WAR S1 S1 27.0 ~ 29.0 5000K SPMWH 541MD5WAR S2 S2 29.0 ~ 31.0 SPMWH 541MD5WAR S3 S3 31.0 ~ 33.0 SPMWH 541MD5WAQ S1 S1 26.5 ~ 28.5 5700K SPMWH 541MD5WAQ S2 S2 28.5 ~ 30.5 SPMWH 541MD5WAQ S3 S3 30.5 ~ 32.5 SPMWH 541MD5WAP S1 S1 26.0 ~ 28.0 6500K SPMWH 541MD5WAP S2 S2 28.0 ~ 30.0 SPMWH 541MD5WAP S3 S3 30.0 ~ 32.0 Notes: 1)SAMSUNG ELECTRONICS maintains a tolerance of ±5% on Luminous Flux measurements. 2)" " (the quantity of PKG on the Reel) can be "T"(2,500pcs) or "1"(10,000pcs). 3)Warm white : " " can be "0"(Whole Bin), "H"(Half Bin) or "M"(Quarter Bin) of the color binning. Cool white : " " can be "0"(Whole Bin) or "M"(Quarter Bin) of the color binning. http://www.samsungled.com 3 / 48

2) Color Bins (T s = 25 ) 1) Color Binning Nominal CCT Product Code Color Rank Chromaticity Bins SPMWH 541MD5WAW0S1 SPMWH 541MD5WAW0S2 SPMWH 541MD5WAW0S3 W0(Whole bin) W1, W2, W3, W4, W5, W6, W7, W8, W9, WA, WB, WC, WD, WE, WF, WG SPMWH 541MD5WAWHS1 2700K SPMWH 541MD5WAWHS2 WH(Half bin) W5, W6, W7, W8, W9, WA, WB, WC SPMWH 541MD5WAWHS3 SPMWH 541MD5WAWMS1 SPMWH 541MD5WAWMS2 WM(Quarter bin) W6, W7, WA, WB SPMWH 541MD5WAWMS3 SPMWH 541MD5WAV0S1 SPMWH 541MD5WAV0S2 SPMWH 541MD5WAV0S3 V0(Whole bin) V1, V2, V3, V4, V5, V6, V7, V8, V9, VA, VB, VC, VD, VE, VF, VG SPMWH 541MD5WAVHS1 3000K SPMWH 541MD5WAVHS2 VH(Half bin) V5, V6, V7, V8, V9, VA, VB, VC SPMWH 541MD5WAVHS3 SPMWH 541MD5WAVMS1 SPMWH 541MD5WAVMS2 VM(Quarter bin) V6, V7, VA, VB SPMWH 541MD5WAVMS3 SPMWH 541MD5WAU0S1 SPMWH 541MD5WAU0S2 SPMWH 541MD5WAU0S3 U0(Whole bin) U1, U2, U3, U4, U5, U6, U7, U8, U9, UA, UB, UC, UD, UE, UF, UG SPMWH 541MD5WAUHS1 3500K SPMWH 541MD5WAUHS2 UH(Half bin) U5, U6, U7, U8, U9, UA, UB, UC SPMWH 541MD5WAUHS3 SPMWH 541MD5WAUMS1 SPMWH 541MD5WAUMS2 UM(Quarter bin) U6, U7, UA, UB SPMWH 541MD5WAUMS3 http://www.samsungled.com 4 / 48

1) Color Binning (Continued) Nominal CCT Product Code Color Rank Chromaticity Bins SPMWH 541MD5WAT0S1 SPMWH 541MD5WAT0S2 SPMWH 541MD5WAT0S3 T0(Whole bin) T1, T2, T3, T4, T5, T6, T7, T8, T9, TA, TB, TC, TD, TE, TF, TG SPMWH 541MD5WATHS1 4000K SPMWH 541MD5WATHS2 TH(Half bin) T5, T6, T7, T8, T9, TA, TB, TC SPMWH 541MD5WATHS3 SPMWH 541MD5WATMS1 SPMWH 541MD5WATMS2 TM(Quarter bin) T6, T7, TA, TB SPMWH 541MD5WATMS3 5000K SPMWH 541MD5WAR0S1 SPMWH 541MD5WAR0S2 SPMWH 541MD5WAR0S3 SPMWH 541MD5WARMS1 SPMWH 541MD5WARMS2 R0(Whole bin) RM(Quarter bin) R1, R2, R3, R4, R5 R6, R7, R8, R9,RA R1, R2, R3, R4, R5, R6 SPMWH 541MD5WARMS3 5700K SPMWH 541MD5WAQ0S1 SPMWH 541MD5WAQ0S2 SPMWH 541MD5WAQ0S3 SPMWH 541MD5WAQMS1 SPMWH 541MD5WAQMS2 Q0(Whole bin) QM(Quarter bin) Q1, Q2, Q3, Q4, Q5 Q6, Q7, Q8, Q9, QA Q1, Q2, Q3, Q4, Q5, Q6 SPMWH 541MD5WAQMS3 6500K SPMWH 541MD5WAP0S1 SPMWH 541MD5WAP0S2 SPMWH 541MD5WAP0S3 SPMWH 541MD5WAPMS1 SPMWH 541MD5WAPMS2 P0(Whole bin) PM(Quarter bin) P1, P2, P3, P4, P5 P6, P7, P8, P9, PA P1, P2, P3, P4, P5, P6 SPMWH 541MD5WAPMS3 http://www.samsungled.com 5 / 48

2) Chromaticity Region & Coordinates http://www.samsungled.com 6 / 48

2) Chromaticity Region & Coordinates (Continued) Region CIE X CIE Y Region CIE X CIE Y W rank (2700K) 0.4373 0.3893 0.4465 0.4071 W1 W2 W3 W4 W5 W6 W7 W8 0.4418 0.3981 0.4513 0.4164 W9 0.4475 0.3994 0.4573 0.4178 0.4428 0.3906 0.4523 0.4085 0.4428 0.3906 0.4523 0.4085 0.4475 0.3994 0.4573 0.4178 WA 0.4532 0.4008 0.4634 0.4193 0.4483 0.3919 0.4582 0.4099 0.4483 0.3919 0.4582 0.4099 0.4532 0.4008 0.4634 0.4193 WB 0.4589 0.4021 0.4695 0.4207 0.4538 0.3931 0.4641 0.4112 0.4538 0.3931 0.4641 0.4112 0.4589 0.4021 0.4695 0.4207 WC 0.4646 0.4034 0.4756 0.4221 0.4593 0.3944 0.4700 0.4126 0.4418 0.3981 0.4513 0.4164 0.4465 0.4071 0.4562 0.4260 WD 0.4523 0.4085 0.4624 0.4274 0.4475 0.3994 0.4573 0.4178 0.4475 0.3994 0.4573 0.4178 0.4523 0.4085 0.4624 0.4274 WE 0.4582 0.4099 0.4687 0.4289 0.4532 0.4008 0.4634 0.4193 0.4532 0.4008 0.4634 0.4193 0.4582 0.4099 0.4687 0.4289 WF 0.4641 0.4112 0.4750 0.4304 0.4589 0.4021 0.4695 0.4207 0.4589 0.4021 0.4695 0.4207 0.4641 0.4112 0.4750 0.4304 WG 0.4700 0.4126 0.4813 0.4319 0.4646 0.4034 0.4756 0.4221 Region CIE X CIE Y Region CIE X CIE Y V rank (3000K) 0.4147 0.3814 0.4221 0.3984 V1 V2 V3 V4 V5 V6 V7 V8 0.4183 0.3898 0.4259 0.4073 V9 0.4242 0.3919 0.4322 0.4096 0.4203 0.3833 0.4281 0.4006 0.4203 0.3833 0.4281 0.4006 0.4242 0.3919 0.4322 0.4096 VA 0.4300 0.3939 0.4385 0.4119 0.4259 0.3853 0.4342 0.4028 0.4259 0.3853 0.4342 0.4028 0.4300 0.3939 0.4385 0.4119 VB 0.4359 0.3960 0.4449 0.4141 0.4316 0.3873 0.4403 0.4049 0.4316 0.3873 0.4403 0.4049 0.4359 0.3960 0.4449 0.4141 VC 0.4418 0.3981 0.4513 0.4164 0.4373 0.3893 0.4465 0.4071 0.4183 0.3898 0.4259 0.4073 0.4221 0.3984 0.4299 0.4165 VD 0.4281 0.4006 0.4364 0.4188 0.4242 0.3919 0.4322 0.4096 0.4242 0.3919 0.4322 0.4096 0.4281 0.4006 0.4364 0.4188 VE 0.4342 0.4028 0.4430 0.4212 0.4300 0.3939 0.4385 0.4119 0.4300 0.3939 0.4385 0.4119 0.4342 0.4028 0.4430 0.4212 VF 0.4403 0.4049 0.4496 0.4236 0.4359 0.3960 0.4449 0.4141 0.4359 0.3960 0.4449 0.4141 0.4403 0.4049 0.4496 0.4236 VG 0.4465 0.4071 0.4562 0.4260 0.4418 0.3981 0.4513 0.4164 http://www.samsungled.com 7 / 48

2) Chromaticity Region & Coordinates (Continued) Region CIE X CIE Y Region CIE X CIE Y U rank (3500K) 0.3889 0.3690 0.3941 0.3848 U1 U2 U3 U4 U5 U6 U7 U8 0.3915 0.3768 0.3968 0.3930 U9 0.3981 0.3800 0.4040 0.3966 0.3953 0.3720 0.4010 0.3882 0.3953 0.3720 0.4010 0.3882 0.3981 0.3800 0.4040 0.3966 UA 0.4048 0.3832 0.4113 0.4001 0.4017 0.3751 0.4080 0.3916 0.4017 0.3751 0.4080 0.3916 0.4048 0.3832 0.4113 0.4001 UB 0.4116 0.3865 0.4186 0.4037 0.4082 0.3782 0.4150 0.3950 0.4082 0.3782 0.4150 0.3950 0.4116 0.3865 0.4186 0.4037 UC 0.4183 0.3898 0.4259 0.4073 0.4147 0.3814 0.4221 0.3984 0.3915 0.3768 0.3968 0.3930 0.3941 0.3848 0.3996 0.4015 UD 0.4010 0.3882 0.4071 0.4052 0.3981 0.3800 0.4040 0.3966 0.3981 0.3800 0.4040 0.3966 0.4010 0.3882 0.4071 0.4052 UE 0.4080 0.3916 0.4146 0.4089 0.4048 0.3832 0.4113 0.4001 0.4048 0.3832 0.4113 0.4001 0.4080 0.3916 0.4146 0.4089 UF 0.4150 0.3950 0.4222 0.4127 0.4116 0.3865 0.4186 0.4037 0.4116 0.3865 0.4186 0.4037 0.4150 0.3950 0.4222 0.4127 UG 0.4221 0.3984 0.4299 0.4165 0.4183 0.3898 0.4259 0.4073 Region CIE X CIE Y Region CIE X CIE Y T rank (4000K) 0.367 0.3578 0.3702 0.3722 T1 T2 T3 T4 T5 T6 T7 T8 0.3726 0.3612 0.3763 0.376 T9 0.3744 0.3685 0.3782 0.3837 0.3686 0.3649 0.3719 0.3797 0.3726 0.3612 0.3763 0.3760 0.3783 0.3646 0.3825 0.3798 TA 0.3804 0.3721 0.3847 0.3877 0.3744 0.3685 0.3782 0.3837 0.3783 0.3646 0.3825 0.3798 0.3840 0.3681 0.3887 0.3836 TB 0.3863 0.3758 0.3912 0.3917 0.3804 0.3721 0.3847 0.3877 0.384 0.3681 0.3887 0.3837 0.3898 0.3716 0.395 0.3875 TC 0.3924 0.3794 0.3978 0.3958 0.3863 0.3758 0.3912 0.3917 0.3686 0.3649 0.3719 0.3797 0.3744 0.3685 0.3782 0.3837 TD 0.3763 0.376 0.3802 0.3916 0.3702 0.3722 0.3736 0.3874 0.3744 0.3685 0.3782 0.3837 0.3804 0.3721 0.3847 0.3877 TE 0.3825 0.3798 0.3869 0.3958 0.3763 0.376 0.3802 0.3916 0.3804 0.3721 0.3847 0.3877 0.3863 0.3758 0.3912 0.3917 TF 0.3887 0.3836 0.3937 0.4001 0.3825 0.3798 0.3869 0.3958 0.3863 0.3758 0.3912 0.3917 0.3924 0.3794 0.3978 0.3958 TG 0.395 0.3875 0.4006 0.4044 0.3887 0.3836 0.3937 0.4001 http://www.samsungled.com 8 / 48

2) Chromaticity Region & Coordinates (Continued) Region CIE X CIE Y Region CIE X CIE Y R rank (5000K) 0.3366 0.3369 0.3456 0.3601 R1 R2 R3 R4 R5 Q1 Q2 Q3 Q4 Q5 0.3441 0.3428 0.3539 0.3669 R6 0.3449 0.3515 0.3551 0.3760 0.3369 0.3451 0.3464 0.3688 0.3441 0.3428 0.3363 0.3287 0.3515 0.3487 0.3433 0.3341 R7 0.3527 0.3578 0.3441 0.3428 0.3449 0.3515 0.3366 0.3369 0.3369 0.3451 0.3433 0.3341 0.3449 0.3515 0.3503 0.3396 R8 0.3456 0.3601 0.3515 0.3487 0.3373 0.3534 0.3441 0.3428 0.3449 0.3515 0.3376 0.3616 0.3527 0.3578 0.3464 0.3688 R9 0.3539 0.3669 0.3471 0.3775 0.3456 0.3601 0.3379 0.3698 0.3373 0.3534 0.3464 0.3688 0.3456 0.3601 0.3551 0.3760 RA 0.3464 0.3688 0.3564 0.3851 0.3376 0.3616 0.3471 0.3775 Q rank (5700K) 0.3222 0.3243 0.3292 0.3461 0.3294 0.3306 0.3373 0.3534 Q6 0.3293 0.3384 0.3376 0.3616 0.3217 0.3316 0.3292 0.3539 0.3294 0.3306 0.3227 0.3170 0.3366 0.3369 0.3295 0.3228 Q7 0.3369 0.3451 0.3294 0.3306 0.3293 0.3384 0.3222 0.3243 0.3217 0.3316 0.3295 0.3228 0.3293 0.3384 0.3363 0.3287 Q8 0.3292 0.3461 0.3366 0.3369 0.3212 0.3389 0.3294 0.3306 0.3293 0.3384 0.3207 0.3462 0.3369 0.3451 0.3292 0.3539 Q9 0.3373 0.3534 0.3291 0.3617 0.3292 0.3461 0.3202 0.3535 0.3212 0.3389 0.3292 0.3539 0.3292 0.3461 0.3376 0.3616 QA 0.3292 0.3539 0.3379 0.3698 0.3207 0.3462 0.3291 0.3617 Region CIE X CIE Y Region CIE X CIE Y P rank (6500K) 0.3068 0.3113 0.3126 0.3324 P1 P2 P3 P4 P5 0.3145 0.3187 0.3210 0.3408 P6 0.3135 0.3256 0.3205 0.3481 0.3055 0.3177 0.3117 0.3393 0.3145 0.3187 0.3081 0.3049 0.3221 0.3261 0.3154 0.3119 P7 0.3216 0.3334 0.3145 0.3187 0.3135 0.3256 0.3068 0.3113 0.3055 0.3177 0.3154 0.3119 0.3135 0.3256 0.3226 0.3188 P8 0.3126 0.3324 0.3221 0.3261 0.3041 0.3240 0.3145 0.3187 0.3135 0.3256 0.3028 0.3304 0.3216 0.3334 0.3117 0.3393 P9 0.3210 0.3408 0.3107 0.3461 0.3126 0.3324 0.3015 0.3368 0.3041 0.3240 0.3117 0.3393 0.3126 0.3324 0.3205 0.3481 PA 0.3117 0.3393 0.3200 0.3554 0.3028 0.3304 0.3107 0.3461 Notes: SAMSUNG ELECTRONICS maintains ±0.005 tolerance of Cx, Cy http://www.samsungled.com 9 / 48

2. Characteristics 1) Absolute Maximum Rating Item Symbol Rating Condition Operating temperature range Top -40 ~ +85 - Storage temperature range Tstg -40 ~ +120 - LED junction temperature TJ 110 - Forward Current IF 180 ma - Peak Pulsed Forward Current IFP 300 ma Duty 1/10 pulse width 10ms Assembly Process Temperature - 260, < 10sec - ESD - 5kV HBM 2) Electro-optical Characteristics Item Forward Voltage 1) (V F) (@65 ma, Ts = 25 ) Luminous Flux 2) (Φ v) (@65 ma, Ts = 25 ) Unit Nominal CCT Product Code V - - WA lm 2700K (W ) 3000K (V ) 3500K (U ) 4000K (T ) 5000K (R ) 5700K (Q ) 6500K (P ) Rank Min Typ Max AZ 2.70-2.80 A1 2.80-2.90 A2 2.90-3.00 A3 3.00-3.10 A4 3.10-3.20 *WAW S1 S1 24.0-26.0 *WAW S2 S2 26.0-28.0 *WAW S3 S3 28.0-30.0 *WAV S1 S1 24.5-26.5 *WAV S2 S2 26.5-28.5 *WAV S3 S3 28.5-30.5 *WAU S1 S1 25.0-27.0 *WAU S2 S2 27.0-29.0 *WAU S3 S3 29.0-31.0 *WAT S1 S1 26.0-28.0 *WAT S2 S2 28.0-30.0 *WAT S3 S3 30.0-32.0 *WAR S1 S1 27.0-29.0 *WAR S2 S2 29.0-31.0 *WAR S3 S3 31.0-33.0 *WAQ S1 S1 26.5-28.5 *WAQ S2 S2 28.5-30.5 *WAQ S3 S3 30.5-32.5 *WAP S1 S1 26.0-28.0 *WAP S2 S2 28.0-30.0 *WAP S3 S3 30.0-32.0 Reverse Voltage (@5 ma, Ts = 25 ) V - - - 0.7-1.2 Color Rendering Index 3) (R a) - - - 5 80 - - Special CRI 4) (R9) - - - - 0 - - Thermal resistance (Rth, j-s) /W - 16 - Notes: 1)~4) SAMSUNG ELECTRONICS maintains a tolerance of V F:±0.1 V, Φ v :±5 %, R a :±3.0, R9 :±6.5 on measurements 5) " * " is Product Code of "SPMWH 541MD5" http://www.samsungled.com 10 / 48

3. Typical Characteristics Graph (T s = 25 ) 1) Spectrum Distribution [CCT : 2700K & 3000K] [CCT : 3500K & 4000K] http://www.samsungled.com 11 / 48

[CCT : 5000K & 5700K] [CCT : 6500K] http://www.samsungled.com 12 / 48

2) Forward Current Characteristics [Relative Luminous Flux vs. Forward Current] (T s = 25 ) [Forward Current vs. Forward Voltage] (T s = 25 ) http://www.samsungled.com 13 / 48

3) Temperature Characteristics [Relative Luminous Flux vs. Ts] (I F = 65mA) [Forward Voltage vs. Ts] (I F = 65mA) http://www.samsungled.com 14 / 48

4) Color shift Characteristics [Color Δx, Δy vs. Forward Current] (T s = 25 ) [Color Δx, Δy vs. Ts] (I F = 65mA) http://www.samsungled.com 15 / 48

5) Derating Curve 6) Beam Angle Characteristics http://www.samsungled.com 16 / 48

4. Outline Drawing & Dimension 1. Tolerance is ±0.10 mm 2. The maximum compressing force is 15N on the body a 3. Do not place pressure on the encapsulation resin b Left Side View Top View Bottom View Anode Mark a b Cathode Anode Front View Ts Recommended Land Pattern Notes: 1) This LED has built-in ESD protection device(s) connected in parallel to LED Chip(s). 2) Ts point & measurement method 1 Measure the nearest point to the thermal pad. If necessary, remove PSR of PCB to reach Ts point. 2 Thermal pad must be soldered to the PCB to dissipate heat properly. Otherwise, LED can be damaged. 3) Precautions 1 The pressure on the LEDs will influence to the reliability of the LEDs. Precautions should be taken to avoid the strong pressure on the LEDs. Do not put stress on the LEDs during heating. 2 Re-soldering should not be done after the LEDs have been soldered. If re-soldering is unavoidable, LED`s characteristics should be carefully checked before and after such repair. 3 Do not stack assembled PCBs together. Since materials of LEDs is soft, abrasion between two PCB assembled with LED might cause catastrophic failure of the LEDs. http://www.samsungled.com 17 / 48

5. Reliability Test Items and Conditions 1) Test Items Test Item MSL Test Room Temperature life test High Temperature life test High Temperature humidity life test Low Temperature life test Powered Temperature Cycle test Thermal Shock High Temperature Storage Low Temperature Storage ESD(HBM) Test Conditions 125 24hrs drying 60, 60 %RH 120hrs 260 10sec 3 cycles Test Hours/Cycles Sample No 1 cycle 11 25 ±3, DC180 ma 1,000 hrs 22 85 ±3, DC180 ma 1,000 hrs 22 85 ±3, 85 %±2 %RH, DC180 ma 1,000 hrs 22-40 ±3, DC180 ma 1,000 hrs 22-45 /20 min 85 /20 min, Sweep 100min cycle on/off: each 5 min, DC 180mA -45 /15 min 125 /15 min Hot plate 180 100 cycle 22 500 cycle 100 Ta=120 ±3 1000 hrs 11 Ta=-40 ±3 1000 hrs 11 R1:10 MΩ, R2:1.5 kω, C:100 pf, V = ±5 kv 5 times 5 ESD(MM) Vibration Test R1:10 MΩ, R2: 0, C:200 pf, V = ±0.5 kv 20~2000~20 Hz 200 m/s 2, Sweep 4 min X, Y, Z 3 direction, each 1 cycle 5 times 5 4 cycles 11 Mechanical Shock Test 1500G, 0.5 ms 5 cycles 11 2) Criteria for Judging the Damage Item Symbol Test Condition Min Limit Max Forward Voltage VF IF = 65 ma Init. Value*0.9 Init. Value*1.1 Luminous Flux Φ v IF = 65 ma Init. Value*0.7 Init. Value*1.2 http://www.samsungled.com 18 / 48

6. Solder Conditions 1) Reflow Conditions ( Pb Free ) Reflow Frequency : 2 times max. 2) For Manual Soldering Not more than 5 seconds @Max. 300, under soldering iron. http://www.samsungled.com 19 / 48

7. Tape & Reel 1) Taping Dimension (unit : mm) Anode Mark (Cutting side) Tapping Diretion End Start More than 500mm Unloaded tape Mounted with LED package More than 100~200mm Unloaded tape Leading part more than 500mm http://www.samsungled.com 20 / 48

2-1) Reel Dimension (max 2,500 pcs) 2-2) Reel Dimension (max 10,000 pcs) Symbol A B C W1 W2 Spec(mm) Ø330±1 80±1 13±0.5 13±0.3 17.5±1 (1) Quantity : The quantity/reel to be 2,500 pcs or 10,000 pcs,. (2) Cumulative Tolerance : Cumulative tolerance/10 pitches to be ±0.2mm (3) Adhesion Strength of Cover Tape : Adhesion strength to be 0.1-0.7N when the cover tape is turned off from the carrier tape at 10 angle to be the carrier tape. (4) Packaging : P/N, Manufacturing data code no. and quantity to be indicated on a damp proof Package. http://www.samsungled.com 21 / 48

8. Label Structure 1) Label Structure abcdef A1 1S1 SPMWHT541MD5WA 0S1 A1 1S1 01 IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII GLAW94001 / 1001 / 2,500 pcs IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII Rank Code N.B) Denoted rank is the only example. ' ' means All kind of Chromaticity Coordinate Rank. Rank Code ab : Forward Voltage(V F) Rank (refer to page. 11) cd : Chromaticity Coordinate Rank (refer to page. 4~10) ef : Luminous Flux(Φ v, lm) Rank (refer to page. 3) 2) LOT Number The Lot number is composed of the following characters A1 1S1 SPMWHT541MD5WA 0S1 A1 1S1 01 IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII GLAW94001 / 1001 / 2,500 pcs IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII 123456789 / 1abc / 2,500 PCS 1 2 3 4 : Production Site (S:SAMSUNG ELECTRONICS, G:TIAJIN CHINA) : L (LED) : Product State (A:Normality, B:Bulk, C:First Production, R:Reproduction, S:Sample) : Year (Y:2014, Z:2015, A:2016...) 5 : Month (1 ~ 9, A, B, C) 6 : Day (1 ~ 9, A, B ~ V) 789 : SAMSUNG ELECTRONICS LED Product number (001 ~ 999) abc : Reel Number (001 ~ 999) http://www.samsungled.com 22 / 48

9. Packing Structure 1-1) Packing Process (The quantity of PKG on the Reel to be Max 2,500 pcs) Reel A1 1S1 SPMWHT541MD5WA 0S1 A1 1S1 01 IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII GLAW94001 / 1001 / 2,500 pcs IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII LEVEL 2a Aluminum Vinyl Bag A1 1S1 SPMWHT541MD5WA 0S1 A1 1S1 01 IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII GLAW94001 / 1001 / 2,500 pcs IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII Material : Paper(SW3B(B)) TYPE SIZE(mm) L W H 7inch 245±5 220±5 182±5 7inch 245±5 220±5 86±5 1 SIDE A1 1S1 SPMWHT541MD5WA 0S1 A1 1S1 01 IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII GLAW94001 / 1001 / 25,000 pcs IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII H CHIP LED L W 1 http://www.samsungled.com 23 / 48

1-2) Packing Process (The quantity of PKG on the Reel to be Max 10,000 pcs) Reel A1 1S1 SPMWH1541MD5WA 0S1 A1 1S1 01 IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII GLAV94001 / 1001 / 10,000 pcs IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII LEVEL 2a Aluminum Vinyl Bag A1 1S1 SPMWH1541MD5WA 0S1 A1 1S1 01 IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII GLAV94001 / 1001 / 10,000 pcs IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII A1 1S1 SPMWH1541MD5WA 0S1 A1 1S1 01 IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII GLAV94001 / 1001 / 150,000 pcs IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII [Box Label] Box SIZE(mm) L W H Inner 340±5 370±5 80±5 Outer 345±5 378±5 405±5 http://www.samsungled.com 24 / 48

2) Aluminum Packing Bag A1 1S1 SPMWHT541MD5WA 0S1 A1 1S1 01 IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII GLAW94001 / 1001 / 2,500 pcs IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII Silica gel & Humidity Indicator Card in Aluminum Vinyl Bag http://www.samsungled.com 25 / 48

10. Precaution for use 1) For over-current-proof function, customers are recommended to apply resistors to prevent sudden change of the current caused by slight shift of the voltage. 과전류 방지를 위해 전압의 미세한 이동에 의해 야기되는 전류의 순간 변화를 방지하기 위해 저항 등의 설치를 권장함. 2) This device should not be used in any type of fluid such as water, oil, organic solvent, etc. When washing is required, IPA is recommended to use. 제품은 물, 오일, 유기물과 같은 액체 타입에서의 사용은 제한되며, 세정이 필요할 시에는 IPA 사용을 권장함. 3) When the LEDs illuminate, operating current should be decided after considering the ambient maximum temperature. LED의 발광 시, 동작 전류는 주변 최고온도를 고려하여 결정되어야 함. 4) LEDs must be stored in a clean environment. If the LEDs are to be stored for 3 months or more after being shipped from Samsung Electronics, they should be packed by a sealed container with nitrogen gas injected.(shelf life of sealed bags: 12 months, temp. ~40, ~90%RH) LED의 보관은 청정한 환경에서 보존되어져야 하며, 만약 삼성전자로부터 공급받는 후 3개월 또는 그 이상 보관이 필요하다면 질소 가스를 동봉한 보존용기에 보관되어야 함. (보존 bag의 수명 : 12 개월, 보존 온도 ~40, 습도 ~90%RH) 5) After storage bag is open, device subjected to soldering, solder reflow, or other high temperature processes must be: 보존 Bag이 개봉된 후에, 납땜이나 reflow등의 높은 온도에 노출되는 제품은 다음의 사항에 부합되어야 함. a. Mounted within 672 hours(28 days) at an assembly line with a condition of no more than 30 /60%RH, a. 제품은 30 /60%RH보다 같거나 낮은 조립조건에서 672시간(28일)이내에 조립해야 함. b. Stored at <10%RH. b. 10% 이하의 상대습도에서 보관되어야 함. 6) Repack unused Products with anti-moisture packing, fold to close any opening and then store in a dry place. 사용하지 않은 제품은 방습팩에 넣어 개봉 부위를 닫아서 다시 포장한 후, 건조한 장소에서 보관할 것을 권장함. http://www.samsungled.com 26 / 48

7) Devices require baking before mounting, if humidity card reading is >60% at 23±5. 만약 습도표시카드의 수치가 23±5 에서 60% 이상이라면, 제품 실장 전 baking해야 함. 8) Devices must be baked for 1 hour at 60±5, if baking is required. 만약 baking이 필요하다면, 제품은 60±5 에서 1시간 정도 baking 되어야 함. 9) The LEDs are sensitive to the static electricity and surge. It is recommended to use a wrist band or anti-electrostatic glove when handling the LEDs. LED는 정전기 및 서지에 민감한 제품이므로, LED 제품을 다룰 시에는 정전기 방지장갑이나 손목밴드를 사용하기를 권장함. If voltage exceeding the absolute maximum rating is applied to LEDs, it may cause damage or even destruction to LED devices. 만약 절대 허용치를 초과하는 전압이 LED에 가해지면, LED 소자는 파괴되거나 손상될 수 있음. Damaged LEDs may show some unusual characteristics such as increase in leak current, lowered turn-on voltage, or abnormal lighting of LEDs at low current. 손상된 제품은 누설전류의 증가, Turn on 전압의 저하, 저 전류에서의 점등불량 등의 이상 거동을 보일 수 있음. 10) VOCs (volatile organic compounds) can be generated from adhesives, flux, hardener or organic additives used in luminaires (fixtures). Transparent LED silicone encapsulant is permeable to those chemicals and they may lead a discoloration of encapsualnt when they expose to heat or light. VOCs(휘발성 유기 화합물)는 등기구에 사용되는 접착제, Flux, 경화제, 유기물 첨가제에서 발생하여 LED 실리콘 봉지제를 투과하고, 빛 또는 열에 노출되었을 때 변색이 발생 할 수 있음. This phenomenon can cause a significant loss of light emitted(output) from the luminaires(fixtures). 이러한 현상은 등기구로부터 나오는 빛의 중대한 손실을 줄 수 있음. In order to prevent these problems, we recommend you to know the physical properties of the materials used in luminaires, They must be selected carefully. 이러한 문제 발생 방지를 위해서, 등기구에 사용되는 자재에 대한 물성을 알고 주의하여 선택 되어야함. http://www.samsungled.com 27 / 48

11) Risk of Sulfurization (or Tarnishing) The LED from Samsung Electronics uses a silver-plated lead frame and its surface color may change to black(or dark colored) when it is exposed to sulfur(s), chlorine (Cl) or other halogen compound. 삼성전자의 LED는 Ag(은)을 도금한 리드프레임을 사용함. 이 리드프레임의 표면이 황(S), 염소(Cl), 또는 다른 할로겐 화합물들에 노출시 Ag(은)은 검정(또는 어두운색)으로 바뀔 수 있음. Sulfurization of lead frame may cause intensity degradation, change of chromaticity coordinates and, in extreme cases, open circuit. It requires caution. 리드 프레임의 황화(Sulfurization)는 광량 저하, 색좌표 변화 및 심한 경우 LED 무등(Open) 불량을 일으킬 수도 있으니 주의가 필요함. Due to possible sulfurization of lead frame, LED should not be used and stored together with oxidizing substances made of materials in a following list, : Rubber, plain paper, lead solder cream and so on. 리드 프레임 황화(Sulfurization)의 근원이 될 수 있으니 LED는 아래의 목록으로 만들어진 산화성 물질들과 함께 저장, 사용이 불가함 : 고무, 일반 종이, 납땜 크림 등 http://www.samsungled.com 28 / 48

12. Hazard Substance Analysis 1) SVHC (Reach) Report http://www.samsungled.com 29 / 48

http://www.samsungled.com 30 / 48

http://www.samsungled.com 31 / 48

http://www.samsungled.com 32 / 48

http://www.samsungled.com 33 / 48

http://www.samsungled.com 34 / 48

http://www.samsungled.com 35 / 48

http://www.samsungled.com 36 / 48

http://www.samsungled.com 37 / 48

http://www.samsungled.com 38 / 48

http://www.samsungled.com 39 / 48

http://www.samsungled.com 40 / 48

http://www.samsungled.com 41 / 48

http://www.samsungled.com 42 / 48

http://www.samsungled.com 43 / 48

http://www.samsungled.com 44 / 48

http://www.samsungled.com 45 / 48

http://www.samsungled.com 46 / 48

http://www.samsungled.com 47 / 48

Revision History Date No. Revision History Drawn Writer Approved 2013.02.08 1.0 New version. W.H Jung Y.T KIM 2013.03.06 2.0 Add up Quarter and half of color binning. W.H Jung Y.T KIM 2013.03.25 3.0 1) Change of tapping Q'ty from 2,000 pcs to 2,500 pcs. 2) Change of CIE tolerance x,y:±0.005 C.H. KWON Y.T KIM 2013.05.14 4.0 Add up a mark of UL certification. W.H Jung Y.T KIM 2013.06.25 5.0 1) Add up ErP(Energy-related Products) of the Energy regulation. 2) Change of Graph on Color shift Characteristics W.H Jung Y.T KIM 2013.11.09 6.0 1) Deletes ErP(Energy-related Products) codes in the product data sheet. W.H Jung S.B Yun 2014.01.23 7.0 1) Update of SGS data. 2) Deletes UL mark of the label on the reel. 3) Add up a Small box W.H Jung S.B Yun 2015.02.03 8.0 Maximum Current upgade(150 180mA) Y.J Cho J.K Park http://www.samsungled.com 48 / 48