저희 제품을 이용하여 주셔서 감사합니다. 사용 전에 고객님의 안전과 원활한 이용을 위하여 사용자 설명서를 꼭 읽어 주시기 바랍니다. QUICK GUIDE 간편메뉴얼 ES-K7H
사용설명서 목차 제품외형 유선인터페이스 설치방법 컴퓨터환경설정 플랫폼설치 주의사항 플랫폼운영 품질보증서
제품외형 및 유선 인터페이스 전원 필라이트 열상이미지센서 카메라 1 카메라 2 7 인치 HD 스크린 온도센서 브라켓 스피커 RJ45 네트워크 리셋 DC12V 전원 RJ485 ALARM.OUT 1. NO 2.COM 3.NC 1. DO 2. DI 3. GND * 케이블 사양은 기능 및 성능 향상을 위해 예고없이 변경될 수 있습니다.
설치 방법 Step 2 Step 3 Step 1 게이트에 장치를 설치하십시오. Step Step 게이트에 직경 D=mm 의 구멍을 만드십시오. 권장 위치는 입구 끝에서 /~/ 입니다. 장비 장착 브래킷을 게이트 구멍에 삽입하고장비 내부에서 장비 너트를 고정하십시오. Step 해당 장치를 적절한 각도 ( 수직 각도 - ) 로조정하십시오. * 폴대형 / 스탠드형 조립방법은 홈페이지 자료실을 참고 해 주세요.
컴퓨터 환경설정 장치의 기본 주소는 다음과 같습니다. IP 주소아이디비밀번호포트... admin ㆍ chrome( 크롬 ) 을 사용하시기 바랍니다. ㆍ정상적인 작동을 위해서는 PC 의 IPv 주소가 IP 카메라의 IP 주소와 동일한 네트워크망에있어야 합니다. 윈도우 시스템의 특정 설정은 다음과 같은 방법을 참조하시기 바랍니다. Step Step PC 의 IPv 주소를 확인 합니다. 시작 제어판 네트워크 및 인터넷 네트워크 및 공유 센터 로컬 네트워크 속성 IPv 어댑터순 으로 설정 변경하십시오. IP 가...X 인경우 플랫폼에서 장치를 직접 추가 할 수 있습니다. 이 네트워크망에 IP 주소가 없으면 단계로 진행하여 해당 네트워크망의 IP 범위를 늘리십시오. 닫기 속성 을 클릭하고 인터넷 프로토콜 버전 (TCP / IPv) 를 두 번 클릭 한 다음 IP 주소에서 고급 추가 클릭하고 장치와 동일한 네트워크망 IP 를 입력하십시오. 예제 ) [...] 추가 확인 확인 확인 후, IP 를 추가하고 종료하십시오.
플랫폼 설치 www.ehoosys.com 접속고객지원메뉴클릭기술자료실클릭실행프로그램다운로드 EHOOSYS.exe Step 운영 체제에서 "EHOOSYS.exe" 를 두 번 클릭하고 설치 암호 "" 을 입력한 후 지시에 따라 설치를 수행하십시오. Step 설치가 완료되면 바탕 화면에 EHOOSYS 아이콘이 표시됩니다. 안면인식 열화상 카메라 사용시 주의사항 온도 측정의 정확성을 위해 다음과 같은 단계를 따르시기 바랍니다 본제품은의료기기가아닙니다. 적정작동온도는 ~ 입니다. 모자를착용하거나이마를가릴경우주의하시기바랍니다. 역광일경우온도측정이다르게나올수있습니다. 내부전용장치이므로내부설치를권장합니다. 각도가 도이상벗어날경우온도차가날수있습니다.
플랫폼 운영 로그인 방법 ㆍ Chrome( 크롬 ) 을사용하시기바랍니다. ㆍ EHOOSYS 아이콘을두번클릭하여로그인인터페이스로들어갑니다. 사용자이름 user 비밀번호 기기추가 Step 플랫폼에 로그인 한 후 EHOOSYS 왼쪽의 " 장치 " 를 확인하고 " 장치 스캔 " 을 클릭 합니다. Step 장치를 선택하고 " " 또는 " " 추가를 클릭하십시오. 장치구성 Step Step 로그인한후 " 장치기본매개변수 " 를확인하고 "Area " 로영역을선택하십시오. 네트워크, 장치의식별매개변수및갤러리보기, 장치삭제등과같은다른매개변수도구성하십시오. 온도측정설정 : 장치목록인터페이스에서 " 기능매개변수 " 를클릭하고 " 온도점검 ", " 알람온도 " 를설정한다음 " 설정하기 " 을클릭하여설정을완료하십시오. * 참고 : " 온도 점검 " 은 ". " 로 기본설정이 되어있습니다.
품질 보증서 품질보증서 보증기간 모델명 제품 공급일로부터 개월 ES-KH 구입처 고객명 연락처 연락처. 이후커뮤니케이션 ( 주 ) 의보상기준은재정경제원고시소비자피해보상규정에따릅니다.. 본제품은엄격한품질관리및검사과정을거쳐서만들어진제품입니다.. 보증기간중고객이정상으로사용함에있어제품상의이상으로고장이발생한경우는무상수리입니다.. 서비스를받으실때는본보증서를꼭제시하여주십시오. * 다음의경우에는품질보증조건에해당되지않으므로유상수리합니다. 가. 소비자의고의또는과실로인하여발생된피해의경우나. 당사의서비스요원이아닌자가제품의구조, 성능, 기능을개조또는변조하여발생된고장다. 사용전원의이상에의한고장라. 사용방법의부족, 제품의파손, 재설치와관련한사항마. 전시, 사변, 천재지변, 주위의환경변화에의한제품의고장또는결함의경우바. 육안으로확인시파손이나연소된경우 * 무상 보증기간 경과 후의 고장수리는 유상으로 합니다.
Table of Contents Device Layout Wired Interface Device Installation Connecting to the Computer Platform Installation Precautions Platform Operation Warranty Card
Device Layout & Wired Interface Power Key Fill Light Thermal Imaging Sensor Camera #1 Camera #2 7-inch HD Screen Temperature Senser Bracket Speaker RJ45 Reset DC12V Power RJ485 ALARM.OUT 1. NO 2.COM 3.NC 1. DO 2. DI 3. GND * 케이블 사양은 기능 및 성능 향상을 위해 예고없이 변경될 수 있습니다.
Device Installation Step 2 Step 3 Step 1 Installing the device on access gates: Step Step Step Create a hole with a diameter of mm on the access gate. It is recommended to place the hole a third or quarter of the way from the entrance. Insert the equipment mounting bracket into the hole and secure it firmly in position with the equipment nut. Adjust the device to a suitable angle (vertical angle between to degrees). * The steps for installing the device with table brackets and floor stand brackets will be provided on the website.
Connecting to the Computer The factory default values of the device are as follows: IP Address ID Password Port... admin ㆍ The computer s IP address needs to be in the same network segment as that of the device to function properly. Refer to the following steps for the specific settings in a Windows operating system: Step Check the computer s IP address by clicking "Start" "Control Panel" "Network and Internet" "Network and Sharing Center" "Local Network" "Details". If the computer s IP address takes on the form of...x, you can add the device directly onto the computer. If the IP address is not on this network segment, proceed to Step. Step Click "Close" "Properties", select "Internet Protocol Version (TCP / IPv)", click "Advanced" "Add," enter the same network segment IP as the device Ex) (...) and click "Add" "OK" "OK" "OK to add the IP address.
Platform Installation Go to www.ehoosys.com Switch to the English version of the website Click on ʻTechnical Support Search and download ʻEHOOSYS English version Run EHOOSYS_EN.exe Step Step Run EHOOSYS_EN.exe", enter the installation password "", click "Next", and follow the prompts to complete the installation. Once the installation is complete, an icon for EHOOSYS_ will appear on the desktop. Precautions To ensure accurate temperature measurement, please follow the steps below: This product is not a medical device. Results may differ when the operating temperature is below or when the wind is blowing. Results may differ when the user is wearing a hat or when the forehead is covered. Results may differ when there is backlight. It is recommended to install the device indoors. Results may differ if the device s optimum angle is exceeded by degrees.
Platform Operation Log In ㆍ Google Chrome or Firefox browser is recommended. ㆍ Double-click on the icon to bring up the login interface. User name user Password Add Device Step After logging in to the platform, check "Device" on the left side of EHOOSYS and click on "Scan Device". Step Select the device and click " " or " Add ". Device Configuration Step Step After logging in to the platform, check "Device - - Basic Parameters", and select the area as "Area ". You can also configure other parameters such as network, identification parameters of the device, viewing the gallery, and device deletion. Temperature measurement setting: On the device list interface, click " -Function Parameters", enable "Temperature Check", type in "Alarm Temperature", and click "Set" to complete the setup. * Note : The "Temperature Check" value is set at the factory default of ".".
Warranty Card Warranty Card Warranty Period Model Dealer year from the date of purchase ES-KH Contact Customer Contact. Ehoo Communication s warranty standards shall comply with the regulations issued by Ministry of Finance and Economy in South Korea.. This product was manufactured under strict product quality management and inspection procedures.. If used in a manner appropriate for the purpose of the product within the warranty period, warranty service shall be guaranteed.. Please make sure to bring this warranty card to receive warranty service. * The warranty does not cover the folllowing: a. Abuse or misuse by the customer. b. Failure resulting from alteration or modification of the structure, functions or features of the product in any way by someone other than Ehoo Communication s service center. c. Failure resulting from improper power supply. d. Defects or failure resulting from improper use, damage or reinstallation. e. Defects or failure resulting from war, incidents, natural disasters or a change of environment. f. Visible damange or combustion marks by the naked eye. * During or after the warranty period, repair service shall be charged in accordance with the agreed contract or reqested invoice.
ES-K7H ʻ 안면인식 열화상 카메라 안면인식과온도측정을단한번에! Facial Recognition & Temperature Measurement with One Device! A/S : 031-456-4560 www.ehoosys.com