스펙트럼분석 - 파트타임또는전용 Air Monitoring이가능한 Spectrum Analyzer가 2.4GHz 및 5GHz 대역을원격스캔하여 HT20에서 VHT80까지의 RF 간섭원파악 Aruba Secure Core - 디바이스보증 : 크리덴셜과키의안전한저장과보안부

아루바 303 시리즈캠퍼스액세스포인트 경제적인 802.11ac Wave 2 엔터프라이즈 AP 경제적인가격대의미드레인지아루바 303 시리즈캠퍼스액세스포인트는중간밀도의엔터프라이즈환경을위한고성능 802.11ac MU-MIMO (Wave 2) 를제공합니다. BLE 내장및 802.3af 파워지원으로기업이최저수준의 TCO 로업무효율성과생산성을향상시킬수있도록해줍니다. 컴팩트한아루바 303 시리즈액세스포인트는 5GHz 대역에서 867Mbps, 2.4 GHz 대역에서 300Mbps의최고동시데이터속도를제공합니다 ( 총피크데이터속도 1.2Gbps). 아루바 303은학교, 매장, 창고, 호텔, 사무실등비용에민감하고기기밀도가보통수준인환경을위해설계되었습니다. 303 시리즈 AP에내장된 BLE(Bluetooth Low-Energy) 라디오를아루바비콘으로사용하여최신위치정보, 실내길안내, 자산추적, 프록시미티 (Proximity) 기반푸시알림서비스를지원할수있습니다. 또한내장된비콘라디오는배터리전원비콘과스탠드얼론비콘들이대규모로구축되어있는네트워크의원격관리를지원합니다. 이를기반으로기업은모빌리티컨텍스트를활용하여향상된사용자경험을제공하고무선네트워크가치를증대시키는애플리케이션을개발할수있습니다. 303 시리즈 AP의강점 통합 AP 컨트롤러와함께, 또는컨트롤러없이구축가능 - 303 시리즈액세스포인트는컨트롤러기반 (ArubaOS) 또는컨트롤러리스 (InstantOS) 모드어떤식으로든구축이가능합니다. Multi-User MIMO (Wave 2) 지원듀얼라디오 2x2 802.11ac 액세스포인트 - 5GHz 대역에서최대 867Mbps(2SS/VHT80 클라이언트 ), 2.4 GHz 대역에서최대 300Mbps(2SS/VHT40 클라이언트 ) 지원 빌트인 BLE(Bluetooth Low-Energy) 라디오 - 여러대의아루바비콘 (Aruba Beacons) 으로부터동시에신호를수신하는 BLE 인에이블드모바일디바이스에서위치기반서비스지원 - Aruba Asset Tags와함께사용하여자산추적가능 ACC(Advanced Cellular Coexistence) - 3G/4G 셀룰러네트워크, 분산안테나시스템, 상용스몰셀 / 펨토셀장비로인한간섭최소화 UC 애플리케이션을위한 QoS - Skype for Business의암호화된화상회의, 음성, 채팅, 데스크톱공유등의 UC(Unified Communication) 앱들을위한우선순위처리및정책실행지원 AppRF 기술이 Deep Packet Inspection을활용하여 2,500 여엔터프라이즈앱또는앱그룹에대한분류및차단, 우선순위화또는대역폭제한을실행 RF 관리 - Adaptive Radio Management (ARM) 기술과 AirMatch가환경과클라이언트밀도에따라채널, 채널폭, 파워설정을자동으로할당. Airtime Fairness를제공하고 AP들이 RF 간섭원의영향을받지않도록보장함으로써안정적인고성능 WLAN 제공 - 아루바 303 시리즈 AP는스펙트럼분석및 WIP(Wireless Intrusion Protection) 를위한파트타임또는전용에어모니터링, 리모트로케이션을본사리소스까지확장하는 VPN 터널, 이더넷단자가없는곳에서의무선메시연결을제공하도록구성가능

스펙트럼분석 - 파트타임또는전용 Air Monitoring이가능한 Spectrum Analyzer가 2.4GHz 및 5GHz 대역을원격스캔하여 HT20에서 VHT80까지의 RF 간섭원파악 Aruba Secure Core - 디바이스보증 : 크리덴셜과키의안전한저장과보안부팅 (secure boot) 을위해 TPM(Trusted Platform Module) 사용 - 별도의 RF 센서및보안장비필요없이내장된 WIP(Wireless Intrusion Protection) 가위협방지및대응제공 - IP 평판 (Reputation) 및보안서비스를통해악성파일, URL, IP 등을파악하고분류및차단함으로써지능적인온라인위협에대한종합적인방어제공운영모드선택아루바 303 시리즈액세스포인트는고객의관리및구축요구사항에따라다음과같이구축및운영모드를선택할수있습니다. 303 시리즈 AP는컨트롤러기반및컨트롤러리스 (controllerless) 구축모드를둘다지원하는통합 AP로서최대한의유연성을제공합니다. 컨트롤러기반모드 : 아루바모빌리티컨트롤러 (Aruba Mobility Controller) 로아루바 303 시리즈액세스포인트들을관리하여중앙구성, 데이터암호화, 정책실행및네트워크서비스, 분산 / 중앙트래픽포워딩을제공합니다. 컨트롤러리스모드 (Instant 모드 ): Instant 모드에서는컨트롤러기능이 AP 클러스터내에가상화됩니다. 네트워크규모확대및 / 또는변경필요시에는 Instant 구축을손쉽게컨트롤러기반모드로전환할수있습니다. Remote AP (RAP) 모드 : 브랜치구축 Air monitor (AM): WIDS(Wireless IDS), 악성 AP 탐지 (Rogue Detection) 및봉쇄 Spectrum Analyzer (SA): 전용또는하이브리드, RF 간섭원파악 Secure Enterprise Mesh 포털또는포인트여러사이트를연결하는대규모인스톨의경우, Aruba Activate 서비스를통해디바이스프로비저닝, 펌웨어업그레이드, 인벤토리관리를자동화함으로써구축시간을획기적으로단축할수있습니다. Aruba Activate을사용하면 Instant 모드 AP들을사이트로바로배송하여전원만켜면자동구성이가능합니다. SPECIFICATIONS Hardware Variants AP-303: Internal antenna models. Wi-Fi Radio Specifications AP type: Indoor, dual radio, 5GHz 802.11ac 2x2 MIMO and 2.4GHz 802.11n 2x2 MIMO 5GHz (radio 0): - Two spatial stream Single User (SU) MIMO for up to 867 Mbps wireless data rate to individual 2SS VHT80 client devices - Two spatial stream Multi User (MU) MIMO for up to 867 Mbps wireless data rate to two 1SS MU-MIMO capable client devices simultaneously 2.4GHz (radio 1): - Two spatial stream Single User (SU) MIMO for up to 300 Mbps wireless data rate to individual 2SS HT40 client devices Support for up to 256 associated client devices per radio, and up to 16 BSSIDs per radio Supported frequency bands (country-specific restrictions apply): - 2.400 to 2.4835GHz - 5.150 to 5.250GHz - 5.250 to 5.350GHz - 5.470 to 5.725GHz - 5.725 to 5.850GHz Available channels: Dependent on configured regulatory domain Dynamic frequency selection (DFS) optimizes the use of available RF spectrum Supported radio technologies: - 802.11b: Direct-sequence spread-spectrum (DSSS) - 802.11a/g/n/ac: Orthogonal frequency-division multiplexing (OFDM) Supported modulation types: - 802.11b: BPSK, QPSK, CCK - 802.11a/g/n/ac: BPSK, QPSK, 16-QAM, 64-QAM, 256- QAM Transmit power: Configurable in increments of 0.5dBm Maximum (aggregate, conducted total) transmit power (limited by local regulatory requirements): - 2.4GHz band: +21dBm (18dBm per chain) - 5GHz band: +21dBm (18dBm per chain) - Note: conducted transmit power levels exclude antenna gain. For total (EIRP) transmit power, add antenna gain

Advanced Cellular Coexistence (ACC) minimizes the impact of interference from cellular networks Maximum ratio combining (MRC) for improved receiver performance Cyclic delay/shift diversity (CDD/CSD) for improved downlink RF performance Short guard interval for 20MHz, 40MHz and 80MHz channels Space-time block coding (STBC) for increased range and improved reception Low-density parity check (LDPC) for high-efficiency error correction and increased throughput Transmit beam-forming (TxBF) for increased signal reliability and range Supported data rates (Mbps): - 802.11b: 1, 2, 5.5, 11-802.11a/g: 6, 9, 12, 18, 24, 36, 48, 54-802.11n: 6.5 to 300 (MCS0 to MCS15) - 802.11ac: 6.5 to 867 (MCS0 to MCS9, NSS = 1 to 2) - 802.11n high-throughput (HT) support: HT20/40-802.11ac very high throughput (VHT) support: VHT20 /40/80-802.11n/ac packet aggregation: A-MPDU, A-MSDU Wi-Fi Antennas AP-303: Internal antenna models. - Two vertically polarized dual-band downtilt omnidirectional antennas for 2x2 MIMO with peak antenna gain of 3.5dBi (2.4GHz) and 6.9dBi (5GHz) per antenna. - The antennas are optimized for horizontal ceiling mounted orientation of the AP. The downtilt angle for maximum gain is roughly 30 degrees. - Combining the patterns of both antennas per radio, the peak gain of the average (effective) pattern is 2.1dBi in 2.4GHz and 5.7dBi in 5GHz. Other Interfaces E0: One 10/100/1000BASE-T Ethernet network interface (RJ-45) - Auto-sensing link speed and MDI/MDX - PoE-PD: 48Vdc (nominal) 802.3af PoE DC power interface, accepts 2.1/5.5-mm center-positive circular plug with 9.5-mm length Bluetooth Low Energy (BLE) radio - Up to 3dBm transmit power (class 2) and -93dBm receive sensitivity - Integrated vertically polarized omnidirectional antenna with roughly 30 degrees downtilt and peak gain of 4.5dBi Visual indicators (tri-color LEDs): for System and Radio status Reset button: factory reset (during device power-up), LED mode control (normal/off) Serial console interface (proprietary, μusb physical jack) Kensington security slot Power Sources and Consumption The AP supports direct DC power and Power over Ethernet (PoE) When both power sources are available, DC power takes priority over PoE Power sources are sold separately Direct DC source: 12Vdc nominal, +/- 5% Power over Ethernet (PoE): 48Vdc (nominal) 802.3af compliant source Maximum (worst-case) power consumption: 10.1W (PoE) or 8.8W (DC) Maximum (worst-case) power consumption in idle mode: 4.2W (PoE) or 4.0W (DC) Mounting The AP ships with a (black) mount clips to attach to a 9/16-inch or 15/16-inch flat T-bar drop-tile ceiling Several optional mount kits are available to attach the AP to a variety of surfaces; see the Ordering Information section below for details Mechanical Dimensions and weight (unit, excluding mount accessories): - 150mm (W) x 150mm (D) x 35mm (H) or 5.9 (W) x 5.9 (D) x 1.4 (H) - 260g or 9.2oz Dimensions and weight (shipping): - 190mm (W) x 180mm (D) x 60mm (H) or 7.4 (W) x 7.0 (D) x 2.4 (H) - 410g or 14.5oz Environmental Operating: - Temperature: 0 C to +40 C (+32 F to +104 F) - Humidity: 5% to 93% non-condensing Storage and transportation: - Temperature: -40 C to +70 C (-40 F to +158 F) Reliability MTBF: 795khrs (91yrs) at +25C operating temperature

Regulatory FCC/ISED CE Marked RED Directive 2014/53/EU EMC Directive 2014/30/EU Low Voltage Directive 2014/35/EU UL/IEC/EN 60950 EN 60601-1-1 and EN 60601-1-2 For more country-specific regulatory information and approvals, please see your Aruba representative. Regulatory Model Numbers AP-303: APIN0303 Certifications CB Scheme Safety, ctuvus UL2043 plenum rating Wi-Fi Alliance (WFA) certified 802.11a/b/g/n/ac Wi-Fi Alliance certified (WFA) 802.11ac with Wave 2 features WARRANTY Aruba limited lifetime warranty MINIMUM SOFTWARE VERSIONS ArubaOS & Aruba InstantOS 8.3.0.0

ANTENNA PATTERN PLOTS Horizontal planes (top view, AP facing forward) Showing both azimuth (0 degrees) and 30 degrees downtilt patterns Elevation planes (side view, AP facing down) Showing side view with AP rotated 0 and 90 degrees