CD CHANGER JCD-0 WWW.JEDIA.COM
S S S S S S S S C AUTION AVIS SAFETY INSTRUCTIONS IMPORTANT NOTICE I NSTALLATIONS H OW TO USE THE COMPACT DISC MAGAZIN F EATURES F RONT PANEL CONTROLS ~ R EAR PANEL CONTROLS E RROR DISPLAY 7 S PECIFICATIONS 8 B LOCK DIAGRAM 9 ON OFF LEVEL MAIN POWER 0 0 JCD-0 CD CHANGER ON/OFF CD-POWER EJECT RDM RPT DISC SCAN DISC TRACK POWER SENSOR RESET REPEAT RANDOM SCAN PLAY/ PAUSE TRACK DISC STOP DOWN UP DOWN UP
SAFETY INSTRUCTIONS Read all safety instruction before operating the JCD-0.. Install equipment as follow conditions. Install at the place, not bending curved. Do not install this apparatus in a confined space such as a book case or similar unit. The apparatus shall not be exposed to dripping or splashing and no object filled with liquids, such as vases, shall be place on the apparatus. Locate this apparatus away from heat source, such as radiators or other device that produce heat. Do not drop objects or spill liquids into the inside of the apparatus.. Keep in mind the following when connecting the apparatus. Connect the apparatus after reading of O/P manuals. Connect each connection of amplifier perfectly, if not, it maybe Caused hum, damage, electric shock in case of mis-connecting. To prevent electric shock, do not open top cover. Connect the power cord with safety after check of AC power. This apparatus should be serviced by qualified service person. IMPORTANT NOTICE This Compact Disc Changer/Player has been tested and found to comply with the limits for a class B digital device in accordance with the specifications in Subpart J of Part of FCC Rules. This equipment generates and uses radio frequency energy, and it must be installed and used properly in accordance with the manufacturer's instructions. CAUTION USE OF CONTROLS OR ADJUSTMENTS OF PERFORMANCE OR PROCEDURES OTHER THAN THOSE SPECIFIED MAY RESULT IN HAZARDOUS RADIATION EXPOSURE. DO NOT REMOVE THE CHANGER/PLAYER COVER. THERE ARE NO USER SERVICEABLE PARTS INSIDE. REFER TO QUALIFIED SERVICE PERSONNEL ONLY. SAFETY PRECAUTIONS(DISC) Only use compact discs which have this mark: Do not use cracked, bent or scratched discs. If Disc becomes dirty. gently wipe the surface with a soft lint-free cloth. Do not use sprays or cleaners designed for records. Do not expose the disc to direct sunlight. Excessive heat will warp the disc. Do not leave a disc unprotected. Always store it in its case right away from sunlight. Compact discs may not always be recorded at the same volume level or with the same quality. This may result in different volume levels between disc and radio.
I NSTALLATION STORAGE DISC Be sure to keep discs away from CD changer during long-time not use. Be sure to keep in the case. Do not place or store disc in the following place.. Locations exposed to direct sunlight.. Locations directly exposed to a heat vent or heating appliance.. Humid locations. USE OF BATTERIES The battery should be cautious beause it is mercury cell.. The battery is lethal when it used by children. Do not touch hands or mouth.. Mercury cell for V size and use same as the figure.. Check polarity(+,-) and use. RELEASE CR0 MOVABLE SCREW REMOVAL OF MOVABLE SCREW Before install the set, unscrew and remove movable screw. Keep well the detached the screw for the future. INSTALL OF MOVABLE SCREW Before transfer the set, assemble the movable screw, following way. If there is not assemble the movable screw correctly there is quity a possibility that the set may damage.. When assemble the sey, be sure to make start/stop mode.. At this time, remove the magazine.. Assemble the detached movable screw and fasten it with adhesive tape.
H OW TO USE THE COMPACT DISC MAGAZINE INSERTING DISC Inserting discs into the suppled magazine. Up to discs may be inserted into the magazine. The discs are numbered from (bottom tray) to (top tray). Note : Do not touch the recorded side of a disc while inserting or removing it. REMOVING DISCS. Press the eject button to remove the magazine.. Push the release keys to remove the discs PRECAUTIONS. Do not leave the magazine exposed to high temperature or direct sunlight.. Do not attempt to disassemble the magazine.. Take care not to drop the magazine.. Take care not to drop the magazine or knock it against hard surface. Store the pulled-out magazine in a safe place.. Benzine, thinner, or other volatile chemicals may cause damages to the magazine. IMPORTANT NOTICE : Magazine of this unit is only for cm (-inch) CD. Do not insert 8cm (-inch) CD to prevent misuse. Figure. Figure. Figure. INSERTING THE MAGIGANE, REMOVING THE MGAZINE. INSERTING THE MAGAZINE Make sure that the magazine loaded with discs befor inserting it into the player. Be careful to insert the magazine into the player with the label facing upward.. REMOVING THE MAGAZINE Press the "EJECT" button to remove.
S S S S S S S S F EATURES ( FEATURES CAR STEREO AUTO CD CHANGER DECK MECHANISM USE PLAY/PAUSE FUNCTION STOP FUNCTION EJECT FUNCTION DISC SELECT (D-UP, D-DN) TRACK SELECT FUNCTION (T-UP, T-DN) REPEAT(DISC) FUNCTION(RPT) RANDOM(DISC) FUNCTION(RDM) SCAN(DISC) FUNCTION(SCAN) PICK-UP(SONY) PERMISSABLE REMOTE-CONTROL L,R STEREO OUTPUT AND MONO OUTPUT AC, DCV USE REMOTE-CONTROLLER RECEIVER SENSOR LED DISPLAY DAMPER STRUCTURE BY EXTERNAL OLD DAMPER(UNITS) AND COIL SPRING(UNITS) F RONT PANEL CONTROLS ON OFF MAIN POWER LEVEL 0 0 8 POWER ON/OFF PLAY/ PAUSE T-DN D-UP D-DN T-UP RPT RDM SCN 0 REMOTE CONTROLLER JCD-0 CD CHANGER ON/OFF CD-POWER EJECT RDM RPT DISC SCAN DISC TRACK POWER SENSOR RESET REPEAT RANDOM SCAN PLAY/ PAUSE TRACK DISC STOP DOWN UP DOWN UP 8 9 7 0. MAIN POWER SWITCH Press this switch to turn on the set and stand-by LED of No. will be turn on.. POWER LED Press main power switch, power LED will be turn on.. VOLUME Adjust the volume to output of power level.. RESET BUTTON If there are no power response when the CD controller button and LCD window's display is not working correctly, press reset button with pointed pen to play correctly.. MAGAZINE INSERT SLOT Insert disc magazine at this point.. LIQUID CRYSTAL DISPLAY (LCD) LCD will be displayed only when the changer power is on. it displays disc insert data and every operation key in the magazine including disc number, track number and disc icon.
F RONT PANEL CONTROLS 7. REMOTE-CONTROLLER SENSOR RECEIVING LIGHT This is to receive infrared signal form card-type remote controller. (Avoid any foreign substances or contamination) 8. CD-POWER BUTTON(CD-POWER ON/OFF) Press this button to turn on/off the changer. When power is off, the changer will be stopped while turning off the LCD and letters on LCD will be erased at the same time. To change to the changer, press this button again. Then, it strts to play from the original position of disc and track before power off. 9. EJECT BUTTON (EJECT) Press eject button for take out magazine from the CD mechanism. 0. REPEAT PLAY BUTTON (TRACK OR DISC REPEAT) It is used for repeating the play. Pressing this button once,"rpt" at the left upper part of LCD is displayed and the playing is repeated. When this button is pressed for more than seconds, " DISC " and "RPT : is displayer at the upper left of LCD display and the disc on play is repeated. When pressing one of these two buttons repeat ("RPT") or disc repeat (" DISC ", "RPT") once again, the repeat function will be released.. RANDOM PLAYER BUTTOM (TRACK OR DISC RANDOM) It is used for random selection which has nothing to do with containing /sequence of the music in the disc on play and disc sequence of the magazine. Once you press this button, "RDM" is displayed at the upper left of LCD of commander, and it is played randomly without regard to the sequence contained in the disc on play. When this button is pressed for more than seconds, " DISC ", and "RDM" are displayed and disc is selected to play randomly in irregular sequence without regard to the disc sequence in the magazine. Pressing one of these two buttons, random selection ("RDM")or random disc selection (" DISC ","RDM") once again, the random selection will be seleased.. SCAN PLAYER BUTTOM (TRACK OR DISC SCAN) It is used to scan a desired disc or desired music in the disc on play. When pressing this button, "SCAN" is displayed at the lower left of LCD and plays each first track for only 0 seconds, when this button is pressed for move than seconds, " DISC " and "SCAN" is displayed at the left of LCD and plays the first part of each disc for 0 seconds. Pressing this button once again when you get a track or disc you desired by scnning, the scan function will be released.. PLAY/PAUSE BUTTON(PLAY/PAUSE) If this button is pressed while playing, the changer continues to play but the sound does not play. Then "PAUSE" is displayed on LCD display and some etters are blinked. Press this button again in "PAUSE", and it is changed into "PLAY" to play the sound.. STOP BUTTON(STOP) Press this button to stop cd changer. Press PLAY/PAUSE button to play.. TRACK SELECTION(TRACK UP/DOWN)AND TRACK FF/REW It is used to search a track desired so quickly. Press T-UP or T-DOWN button to search a track you desired, while viewing the track displayed in the LCD display. Press this button for more than seconds, and you can make first forwarding or rewinding to the direction as you wish.. DISC SELECTION BUTTON(DISC SELECT) It is used to select a desired disc among discs inserted in magazine. Press D-UP button to select upper disc, and press D-Down button to select the lower disc, while viewing disc number displayed on the LCD.
R EAR PANEL CONTROLS 0VAC T00mAL 0V 0VAC T00mAL 0V 0VAC T00mAL 0V 0VAC T00mAL 0V OUTPUTS CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN AC IN 0-0Hz MAX W DC POWER V MAX.A Balanced MONO STEREO R L REMOTE CONTROL POWER ON/OFF PLAY/PAUSE DISC UP TRACK DOWN TRACK UP DISC DOWN EJECT RANDOM 7 8 9 0 WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK DON'T EXPOSE THIS EQUIPMENT TO RAIN OR MOISTURE. MODEL NO.: JCD-0 CD CHANGER USE ONLY WITH A 0V FUSE 0dB 0dB SCAN REPEAT STOP +V GND GND MADE IN KOREA CAUTION: TO REDUCE THE RISK OF FIRE REPLACE ONLY WITH SAME TYPE FUSE. SERIAL NO.:. AC INLET Plug AC input cord into AC out inlet.. FUSE HOLDER This fuse holder contains AC fuse. Replaces it with same type fuse. If it continuously blow, stop replacing fuse and refer servicing to qualified person. There is DC fuse in P.C.B board.. DC POWER TERMINAL Please note the +,- polarity, when connecting DC V terminal in case of using emergency power source for unexpected AC power failure.. MONO OUTPUT BALANCED Audio signal output connector for mono output 0dB/00ohm balanced.. STEREO L,R OUTPUT Audio signal output connector for stereo L.R output 0dB/00ohm unbalanced. CONNECTOR FOR REMOTE-CONTROLS This connector is for remote controls to signal output. There are ways to operate connector as followed. 0VAC 0V/0V/0VAC VDC S T00mAL 0V 0T T00mAL 0V T TAH 0V Method 8 7 8 9 POWER ON/OFF PLAY/PAUSE DISC UP TRACK DOWN 8 8 GND TRACK UP 7 N.C GND GND DISC DOWN 7 EJECT N.C KEY MATRIX 8 RANDOM Method N.C 9 SCAN 0 0 REPEAT 0 9 STOP 9 9 POWER ON/OFF PLAY/PAUSE DISC UP TRACK DOWN TRACK UP DISC DOWN 7 EJECT 8 RANDOM 9 SCAN 0 REPEAT STOP GND MICOM or CMOS, TTL LEVEL REMOTE CONTROL +V REMOTE CONTROL
E RROR DISPLAY ERROR DISPLAY Error Error Error Error Error Error Error 7 Error 8 Error 9 Error 0 There's no magazine, and DISC is clamping. It is impossible to discharge magazine while ejecting. LOADING is not completed after a certain time(8 sec) passed. UNLOADING is not completed after a certain time(8 sec) passed. ELEVATOR does not reach to the target position after a certain time(8sec) passed. Hole separated. PICKUP is not moved to the center area even after a certain time (8 sec) passed in movement of SLED center area. It is not completed despite more than time of focusing trial. CLV On is not operated to reach CLV constant speed mode, and subq input is proven. Error data or subq is not input for more than.sec. TOC is not read after a certain time( sec)passed. The temperature in the mechanism continues to rise for a certain time( sec) so no more operation can be done. Please contact service center near by in your area if it does not recover by disc up/down button or reset button. Error Error Error Error Error Error Error 7 Error 8 Error 9 Error 0 7
S PECIFICATIONS TECHNICAL Output Level Digital Filter MONO 0dB(0.77V) / BAL L, R 0dB(0.77V) / UNBAL(OPTION) 8-TIMES OVER SAMPLING T.H.D(KHz) LESS THAN 0.0% (JIS A) Signal to Noise Ratio(KHz) MORE THAN 8dB (JIS A) Dynamic Range(KHz) MORE THAN 70dB Channel Separation(KHz) MORE THAN 70dB (JIS A) Frequency Response 0Hz~0KHz( db ) Wow / Flutter BELOW MEASURABLE LIMIT Access Time Power Consumption LONG MAX. 8sec SHORT MAX. sec W GENERAL Power Source(OPTION) Dimensions(mm) (inch) 0V/0V/0V/0VAC 0-0Hz VDC 8(W) x 88(H) x 0(D) 9(W) x.(h) x0.(d) Weight(kg/lbs) 7. /. NOTE Specifications and design subject to change without notice for improvements. 8
LOCK DIAGRAM CD MECHANISM AND SERVO AC POWER 0V/0V/0V/0V 0/0Hz (OPTION) DC POWER V MAX.A +V LEVEL AC FUSE DC FUSE POWER SWITCH LCD -COM L.A L.A L.A POWER TRANS KEY MATRIX L.A REMOTE CONTROL L OUTPUT 0dB/00 (OPTION) R MONO OUTPUT 0dB/00 REG +V 9
JCD-0 CD CHANGER OPERATING INSTRUCTIONS M-OP99070