HP LaserJet Pro M203 Getting Started Guide - XLWW

Transcription

1 LaserJet Pro M203 Getting Started Guide English...1 Bahasa Indonesia...4 한국어...7 ไทย IMPORTANT: First, follow Steps 1-3 on the printer hardware setup poster, then continue with Step 繁體中文 Tiếng Việt Initial setup on the control panel At the printer control panel, check the LED status before beginning software installation. 5. Select the connection method USB connection directly between the printer and the computer Use an A-to-B type USB cable. Windows 1. Do not connect the USB cable before installing the software. The installation process prompts to connect the cable at the appropriate time. If the cable is already connected, restart the printer when installation prompts to connect the cable. 2. Continue to 6. Download and install the software. OS X 1. For OS X, connect the USB cable between the computer and the printer before installing the software. 2. Continue to 6. Download and install the software. Wireless network connection (wireless models only) Before starting the installation, verify that the wireless access point is working correctly. Make sure that the printer, router, and computer are all turned on and that the computer is connected to the same wireless network that the printer will be connected to. 1. Place the CD in the CD-ROM drive, navigate to setup.exe and double click. When the Printer connections dialog appears, choose Make a wireless connection to the device. 2. Follow the on-screen instructions. 3. Select the printer detected by the software. If the printer cannot be detected by the installer, manually input the printer s IP address to continue the installation. NOTE: Print a configuration page to find the printer s IP address. At the printer control panel, press and hold the Resume/Cancel button for 5 seconds, and then release the Resume/Cancel button to print the configuration page. The IP address is listed on the configuration page in the Network Information section. Wired (Ethernet) network connection (optional) Use a standard network cable. 1. Connect the network cable to the printer and to the network. Wait a few minutes for the printer to acquire a network address. 2. Continue to 6. Download and install the software. Manually configure the IP address See the printer user guide for information on how to manually configure the IP address 1

2 6. Download and install the software Method 1: Download HP Easy Start (Windows and OS X) 1. Go to 123.hp.com/laserjet, and click Download. 2. Follow the on-screen instructions and prompts to save the file to the computer. 3. Launch the software file from the folder where the file was saved. Method 2: Download from printer support website (Windows and OS X) 1. Go to 2. Select Software and drivers. 3. Download the software for your printer model and operating system. 4. Launch the software file from the folder where the file was saved. Method 3: Install from the printer CD (Windows only) 1. Insert the printer CD into the computer. 2. Follow the on-screen instructions to install the software. For more information see the Install Notes on the printer CD. Install Notes For more details about the software for the printer, see the install notes file on the printer CD. 7. Mobile printing (optional) 7.2 Wi-Fi Direct (wireless models only) 7.1 Connect the device to the wireless network To print from a phone or tablet, connect the device to the same wireless network as the printer. Apple ios devices (AirPrint): Open the item to print, and select the Action icon. Select Print, select the printer, and then select Print. Android devices (4.4 or newer): Open the item to print, and select the Menu button. Select Print, select the printer, and select Print. Some devices require downloading the HP Print Service plugin app from the Google Play store. Windows Phone: Download the HP AiO Remote app from the Windows Store. Learn more about mobile printing For further information on these and other operating systems (Chrome/Google Cloud Print) go to or scan the QR code below. Wi-Fi Direct allows Wi-Fi capable devices, such as smart phones, tablets, or computers, to make wireless network connection directly to the printer without using a wireless router or access point. Connect to the printer s Wi-Fi Direct signal the same way Wi-Fi capable devices are connected to a new wireless network or hotspot. Enable Wi-Fi Direct Enable HP Web Services in the HP Embedded Web Server (EWS) by following these steps: 1. Connect the printer to a network, and print a configuration page to get the printer IP address. NOTE: To set the IP address manually or configure it automatically, see Configure the network product in the user guide. 2. Open a web browser, enter the printer IP address into the address line, and then press Enter. Example IP address: In the HP EWS, select the Networking tab. 4. Select the Wi-Fi Direct Setup page, select On, and then click Apply. 2

3 8. Set up HP eprint via (optional) Use HP eprint via to print documents by sending them as an attachment to the printer s address from any enabled device, even from devices that are not on the same network. To use HP eprint via , the printer must meet these requirements: The printer must be connected to a wired or wireless network and have Internet access. HP Web Services must be enabled on the printer, and the printer must be registered with HP Connected. Enable HP Web Services (wireless models only) 1. After the printer is connected to the HP Embedded Web Server (EWS), print a configuration page and identify the printer IP address. 2. At the computer, open a web browser and enter the printer IP address into the address line. The HP EWS opens. 3. Click the HP Web Services tab. If the network uses a proxy server do the following: Select the Proxy Settings tab. Select the Check this box if your network uses a proxy server to access the Internet check box. In the Proxy Server field, enter the proxy server address and port number, and then click the Apply button. 4. Select the HP Web Services tab, and click the Enable button. The printer configures the connection to the Internet, and then a message appears indicating an information sheet will print 5. Click the OK button. An eprint page prints out. On the eprint page, look for the address that is automatically assigned to the printer. Troubleshooting User guide The user guide includes printer usage and troubleshooting information. It is available on the printer CD and on the Web: 1. Go to 2. Select a printer or category from the list, and then click User Guides. Check for firmware updates 1. Go to 2. Select a printer or category from the list, and then click Drivers. 3. Select the operating system, and then click the Next button. 4. Select Firmware, and then click the Download button. Additional support resources For HP s all-inclusive help for the printer, go to Solve problems Find advanced configuration instructions Download software updates Join support forums Find warranty and regulatory information Access mobile printing resources Resolve error code messages (First Use) Light Status Attention light is blinking Action Load the paper into the tray Wireless network connection (wireless models only) Verify that the printer and wireless router are turned on and have power. Also make sure the wireless switch is turned on. Verify that the printer is within the range of the wireless network. For most networks, the printer must be within 30 m (100 ft) of the wireless access point (wireless router). Verify the print driver is installed on the computer. Verify that the computer and printer connect to the same wireless network. For Mac, verify that the wireless router supports Bonjour. Restart the wireless router. 3

4 English...1 Bahasa Indonesia...4 한국어...7 ไทย...10 LaserJet Pro M203 Panduan Persiapan 繁體中文...13 Tiếng Việt...16 PENTING: Pertama-tama, ikuti Langkah 1-3 pada poster konfigurasi perangkat keras printer, lalu lanjutkan ke Langkah Konfigurasi awal pada panel kontrol Pada panel kontrol printer, periksa status LED sebelum memulai penginstalan perangkat lunak. 5. Memilih metode sambungan Sambungan USB secara langsung antara printer dan komputer Gunakan kabel USB tipe A-ke-B. Windows 1. Jangan sambungkan kabel USB sebelum menginstal perangkat lunak. Proses penginstalan meminta agar kabel disambungkan pada waktu yang tepat. Jika kabel telah tersambung, hidupkan ulang printer saat penginstalan meminta agar kabel disambungkan. 2. Lanjutkan ke "6. Download dan instal perangkat lunak". OS X 1. Untuk OS X, sambungkan kabel USB antara komputer dan printer sebelum menginstal perangkat lunak. 2. Lanjutkan ke "6. Download dan instal perangkat lunak". Sambungan jaringan nirkabel (hanya model nirkabel) Sebelum menjalankan penginstalan, pastikan jalur akses nirkabel telah berfungsi dengan benar. Pastikan printer, router, dan komputer telah dihidupkan dan komputer tersambung ke jaringan nirkabel sama seperti yang digunakan untuk menyambungkan printer. 1. Masukkan CD ke drive CD-ROM, navigasikan ke setup.exe, lalu klik dua kali. Bila dialog sambungan Printer muncul, pilih Make a wireless connection to the device (Buat sambungan nirkabel ke perangkat). 2. Ikuti petunjuk di layar. 3. Pilih printer yang terdeteksi perangkat lunak. Jika printer tidak terdeteksi oleh penginstal, masukkan alamat IP printer secara manual untuk melanjutkan penginstalan. CATATAN: Cetak halaman konfigurasi untuk menemukan alamat IP printer. Pada panel kontrol printer, tekan terus tombol Resume/Cancel (Lanjut/ Batal) selama 5 detik, lalu lepas tombol Resume/Cancel (Lanjut/Batal) untuk mencetak halaman konfigurasi. Alamat IP tercantum pada halaman konfigurasi dalam bagian Informasi Jaringan. Sambungan jaringan berkabel (Ethernet) (opsional) Gunakan kabel jaringan standar. 1. Sambungkan kabel jaringan ke printer dan jaringan. Tunggu beberapa menit agar printer mendapatkan alamat jaringan. 2. Lanjutkan ke "6. Download dan instal perangkat lunak". Mengkonfigurasi alamat IP secara manual Lihat panduan pengguna printer untuk mendapatkan informasi tentang cara mengkonfigurasi alamat IP secara manual 4

5 6. Download dan instal perangkat lunak Metode 1: Download HP Easy Start (Windows dan OS X) 1. Kunjungi 123.hp.com/laserjet, lalu klik Download. 2. Ikuti petunjuk pada layar dan perintah untuk menyimpan file di komputer. 3. Jalankan file perangkat lunak dari folder yang menyimpan file. Metode 2: Download dari situs web dukungan printer (Windows dan OS X) 1. Kunjungi 2. Pilih Software (Perangkat Lunak) dan drivers (driver). 3. Download perangkat lunak untuk model printer dan sistem operasi Anda. 4. Jalankan file perangkat lunak dari folder yang menyimpan file. Metode 3: Instal dari CD printer (hanya Windows) 1. Masukkan CD printer ke komputer. 2. Ikuti petunjuk pada layar untuk menginstal perangkat lunak. Untuk informasi lebih lanjut, lihat Catatan Penginstalan di CD printer. Catatan Penginstalan Untuk informasi lebih rinci tentang perangkat lunak printer, lihat file catatan penginstalan pada CD printer. 7. Pencetakan seluler (opsional) 7.2 Wi-Fi Direct (hanya model nirkabel) 7.1 Menyambungkan perangkat ke jaringan nirkabel Untuk mencetak dari telepon atau tablet, sambungkan perangkat ke jaringan nirkabel yang sama dengan printer. Perangkat Apple ios (AirPrint): Buka item yang akan dicetak, lalu pilih ikon Action (Tindakan). Pilih Print (Cetak), pilih printer, lalu pilih Print (Cetak). Perangkat Android (4.4 atau versi lebih baru): Buka item yang akan dicetak, lalu pilih tombol Menu. Pilih Print (Cetak), pilih printer, lalu pilih Print (Cetak). Perangkat tertentu mengharuskan Anda men-download aplikasi plugin Layanan HP Print dari Google Play Store. Windows Phone: Download aplikasi HP AiO Remote dari Windows Store. Selengkapnya tentang pencetakan seluler Untuk informasi lebih lanjut tentang hal ini dan sistem operasi lainnya (Chrome/Google Cloud Print) kunjungi " atau pindai kode QR di bawah ini. Wi-Fi Direct memungkinkan perangkat yang mendukung Wi-Fi, misalnya smartphone, tablet, atau komputer, membuat sambungan jaringan nirkabel langsung ke printer tanpa menggunakan router atau jalur akses nirkabel. Sambungkan ke sinyal Wi-Fi Direct printer menggunakan cara yang sama seperti menyambungkan perangkat yang mendukung Wi-Fi ke jaringan nirkabel atau hotspot baru. Mengaktifkan Wi-Fi Direct Aktifkan Layanan Web HP dalam HP Embedded Web Server (EWS) dengan mengikuti langkah-langkah berikut: 1. Sambungkan printer ke jaringan, lalu cetak halaman konfigurasi untuk mendapatkan alamat IP printer. CATATAN: Untuk menetapkan alamat IP secara manual atau mengkonfigurasinya secara otomatis, lihat "Mengkonfigurasi produk jaringan" dalam panduan pengguna. 2. Buka browser web, masukkan alamat IP printer ke baris alamat, lalu tekan Enter. Contoh alamat IP: Pada HP EWS, pilih tab Networking (Jaringan). 4. Pilih halaman Wi-Fi Direct Setup (Konfigurasi Wi-Fi Direct), pilih On (Aktif), lalu klik Apply (Terapkan). 5

6 8. Mengkonfigurasi HP eprint melalui (opsional) Gunakan HP eprint melalui untuk mencetak dokumen dengan mengirimnya sebagai lampiran ke alamat printer dari perangkat apa pun yang mendukung , bahkan dari perangkat di jaringan yang berbeda. Untuk menggunakan HP eprint melalui , printer harus memenuhi persyaratan berikut ini: Printer harus disambungkan ke jaringan berkabel atau nirkabel dan memiliki akses Internet. Layanan Web HP harus diaktifkan di printer, dan printer harus terdaftar di HP Connected. Mengaktifkan Layanan Web HP (hanya model nirkabel) 1. Setelah printer tersambung ke HP Embedded Web Server (EWS), cetak halaman konfigurasi, lalu identifikasikan alamat IP printer. 2. Di komputer, buka browser web, lalu masukkan alamat IP printer di baris alamat. HP EWS akan terbuka. 3. Klik tab HP Web Services (Layanan Web HP). Jika jaringan menggunakan server proxy, lakukan langkah-langkah berikut: Pilih tab Proxy Settings (Pengaturan Proxy). Centang kotak Check this box if your network uses a proxy server to access the Internet (Centang kotak ini jika jaringan Anda menggunakan server proxy untuk mengakses Internet). Pada bidang Proxy Server (Server Proxy), masukkan alamat dan nomor port server proxy, lalu klik tombol Apply (Terapkan) 4. Pilih tab HP Web Services (Layanan Web HP), lalu klik tombol Enable (Aktifkan). Printer akan mengkonfigurasi sambungan ke Internet, lalu pesan ditampilkan untuk menunjukkan bahwa lembar informasi akan dicetak 5. Klik tombol OK. Halaman eprint dicetak. Pada halaman eprint, cari alamat yang ditentukan secara otomatis ke printer. Mengatasi masalah Panduan pengguna Panduan pengguna berisi informasi tentang penggunaan dan cara mengatasi masalah printer. Panduan pengguna tersedia pada CD printer dan web: 1. Kunjungi 2. Pilih printer atau kategori dari daftar, lalu klik User Guides (Panduan Pengguna). Memeriksa pembaruan firmware 1. Kunjungi 2. Pilih printer atau kategori dari daftar, lalu klik Drivers (Driver). 3. Pilih sistem operasi, lalu klik tombol Next (Berikutnya). 4. Pilih Firmware, lalu klik tombol Download. Sumber dukungan tambahan Untuk bantuan lengkap tentang printer HP, kunjungi Mengatasi masalah Menemukan petunjuk konfigurasi tingkat lanjut Men-download pembaruan perangkat lunak Bergabung dengan forum dukungan Mencari informasi jaminan dan peraturan Mengakses sumber pencetakan seluler Menyelesaikan pesan kode kesalahan (Penggunaan Pertama) Status Lampu Lampu perhatian berkedip Tindakan Masukkan kertas ke dalam baki Sambungan jaringan nirkabel (hanya model nirkabel) Pastikan printer dan router nirkabel telah diaktifkan dan dalam keadaan hidup. Pastikan juga tombol nirkabel telah diaktifkan. Pastikan printer telah berada dalam jangkauan jaringan nirkabel. Untuk sebagian besar jaringan, printer harus berada dalam jarak 30 m (100 kaki) dari jalur akses nirkabel (router nirkabel). Pastikan driver cetak telah terinstal di komputer. Pastikan komputer dan printer telah tersambung ke jaringan nirkabel yang sama. Untuk Mac, pastikan router nirkabel mendukung Bonjour. Hidupkan ulang router nirkabel. 6

7 LaserJet Pro M203 시작설명서 English...1 Bahasa Indonesia...4 한국어...7 ไทย 중요 : 繁體中文 Tiếng Việt 프린터하드웨어설치포스터의 1~3 단계를수행한다음 4 단계를진행하십시오. 4. 제어판에서초기설정 소프트웨어를설치하기전에프린터제어판에서 LED 상태를점검합니다. 5. 연결방식선택 프린터와컴퓨터간직접 USB 연결 A-B 형 USB 케이블을사용합니다. Windows 1. 소프트웨어를설치하기전에 USB 케이블을연결하지마십시오. 설치과정중에케이블을연결하라는메시지가표시됩니다. 케이블이이미연결된경우, 설치중케이블을연결하라는메시지가표시되면프린터를재시작합니다 소프트웨어다운로드및설치 로진행합니다. OS X 1. OS X 의경우, 소프트웨어를설치하기전에 USB 케이블을컴퓨터와프린터에연결합니다 소프트웨어다운로드및설치 로진행합니다. 무선네트워크연결 ( 무선모델만해당 ) 설치를시작하기전에무선액세스지점이제대로작동하는지확인하십시오. 프린터, 라우터및컴퓨터가모두켜져있어야하며컴퓨터는프린터를연결하고자하는동일한무선네트워크에연결되어있어야합니다. 1. CD를 CD-ROM 드라이브에삽입하고 setup.exe를찾아더블클릭합니다. 프린터연결대화상자가표시되면장치에무선연결설정을선택합니다. 2. 화면의지시에따릅니다. 3. 소프트웨어가검색한프린터를선택합니다. 설치프로그램이프린터를찾지못하는경우, 프린터의 IP 주소를수동으로입력하고설치를계속합니다. 참고 : 구성페이지를인쇄하여프린터의 IP 주소를찾습니다. 프린터제어판에서재시작 / 취소버튼을 5 초간누르고있다가재시작 / 취소버튼에서손을떼면구성페이지를인쇄할수있습니다. IP 주소는구성페이지의네트워크정보섹션에기재되어있습니다. 유선 ( 이더넷 ) 네트워크연결 ( 선택사항 ) 표준네트워크케이블을사용합니다. 1. 네트워크케이블을프린터와네트워크에연결합니다. 프린터에서네트워크주소를받을때까지몇분대기합니다 소프트웨어다운로드및설치 로진행합니다. IP 주소수동으로구성 S 수동으로 IP 주소를구성하는방법에대한자세한내용은프린터사용설명서 ( 를참조하십시오. 7

8 6. 소프트웨어다운로드및설치 방법 1: HP Easy Start 다운로드 (Windows 및 OS X) hp.com/laserjet으로이동한다음다운로드를클릭합니다. 2. 화면에표시되는안내와알림에따라컴퓨터에파일을저장합니다. 3. 파일이저장된폴더에서소프트웨어파일을실행합니다. 방법 2: 프린터지원웹사이트에서다운로드 (Windows 및 OS X) 소프트웨어및드라이버를선택합니다. 3. 해당프린터모델및운영체제용소프트웨어를다운로드합니다. 4. 파일이저장된폴더에서소프트웨어파일을실행하고. 방법 3: 프린터 CD 에서설치 (Windows 만해당 ) 1. 컴퓨터에프린터 CD를넣습니다. 2. 화면의지시에따라소프트웨어를설치합니다. 자세한내용은프린터 CD의 설치노트파일을참조하십시오. 설치노트 프린터용소프트웨어에대한자세한내용은프린터 CD 의설치노트파일을참조하십시오. 7. 모바일인쇄 ( 선택사항 ) 7.2 Wi-Fi Direct( 무선모델만해당 ) 7.1 무선네트워크에장치연결 핸드폰또는태블릿에서인쇄하려면해당장치를프린터와동일한무선네트워크에연결합니다. Apple ios 장치 (AirPrint): 인쇄할항목을열고작업아이콘을선택합니다. 인쇄를선택하고프린터를선택한다음인쇄를선택합니다. Android 장치 (4.4 이상버전 ): 인쇄할항목을열고메뉴버튼을선택합니다. 인쇄를선택하고프린터를선택한다음인쇄를선택합니다. 일부장치의경우 Google Play 스토어에서 HP 인쇄서비스플러그인앱을다운로드해야합니다. Windows Phone: Windows 스토어에서 HP AiO Remote 앱을다운로드합니다. 모바일인쇄에대해자세히알아보기 관련운영체제 (Chrome/Google 클라우드인쇄 ) 에대한추가정보는 을참조하거나아래의 QR 코드를스캔하십시오. Wi-Fi Direct 를통해스마트폰, 태블릿, 컴퓨터와같은 Wi-Fi 케이블장치를무선라우터나액세스지점을사용하지않고프린터에직접무선네트워크연결을할수있습니다. Wi-Fi 를사용할수있는장치를새무선네트워크또는핫스폿에연결하는방식과동일한방법으로프린터의 Wi-Fi Direct 신호에연결합니다. Wi-Fi Direct 활성화다음단계를수행하여 HP EWS( 내장웹서버 ) 에서 HP 웹서비스를활성화합니다. 1. 프린터를네트워크에연결하고구성페이지를인쇄하여프린터의 IP 주소를확인합니다. 참고 : IP 주소를수동으로설정하거나자동으로구성하려면사용설명서의 네트워크제품구성 을참조하십시오. 2. 웹브라우저를열고주소입력란에프린터의 IP 주소를입력한다음 Enter를누릅니다. IP 주소예 : HP EWS에서네트워킹탭을선택합니다. 4. Wi-Fi Direct 설정페이지를선택하고켜짐을선택한다음적용을클릭합니다. 8

9 8. 이메일을통한 HP eprint 설정 ( 선택사항 ) 이메일을통한 HP eprint 를사용하면장치가동일한네트워크상에없어도이메일을사용할수있는모든장치에서프린터의이메일주소로문서를첨부파일로전송하여인쇄할수있습니다. 이메일을통한 HP eprint를사용하려면프린터가다음요구사항을충족해야합니다. 프린터가유선또는무선네트워크에연결되어있고인터넷에접속되어야합니다. 프린터에 HP 웹서비스가활성화되어있어야하며 HP Connected 에프린터가등록되어있어야합니다. HP 웹서비스활성화 ( 무선모델만해당 ) 1. 프린터를 HP 내장웹서버 (EWS) 에연결한다음, 구성페이지를인쇄하여프린터의 IP 주소를확인합니다. 2. 컴퓨터에서웹브라우저를열고주소줄에프린터 IP 주소를입력합니다. HP EWS가열립니다. 3. HP 웹서비스탭을클릭합니다. 네트워크가프록시서버를사용하는경우, 다음과같이합니다. 프록시설정탭을선택합니다. 네트워크에서프록시서버를사용하여인터넷에액세스하는경우확인란을선택합니다. 프록시서버필드에프록시서버주소및포트번호를입력한다음적용버튼을클릭합니다. 4. HP 웹서비스탭을선택한다음사용버튼을클릭합니다. 프린터가인터넷에대한연결을구성하며정보시트가인쇄될것이라는메시지를표시합니다. 5. 확인버튼을클릭합니다. eprint 페이지가인쇄됩니다. eprint 페이지에서프린터에자동으로할당된이메일주소를찾습니다. 문제해결 사용설명서 사용설명서에프린터사용법및문제해결정보가포함되어있습니다. 프린터 CD 및웹에서제공됩니다 목록에서프린터또는카테고리를선택한다음사용설명서를클릭합니다. 펌웨어업데이트확인 목록에서프린터또는카테고리를선택한다음드라이버를클릭합니다. 3. 운영체제를선택하고다음버튼을클릭합니다. 4. 펌웨어를선택한다음다운로드버튼을클릭합니다. 추가지원리소스프린터에대한모든것을포함하는 HP 도움말은 에서확인하십시오. 문제해결 고급구성지침찾기 소프트웨어업데이트다운로드 지원포럼가입 보증및규정정보찾기 모바일인쇄리소스액세스 오류코드메시지해결 ( 최초사용 ) 표시등상태주의표시등깜박임 작업용지함에용지삽입 무선네트워크연결 ( 무선모델만해당 ) 프린터및무선라우터가켜져있고전원에이상이없는지확인합니다. 무선스위치가켜져있는지도확인합니다. 프린터가무선네트워크범위내에있는지확인합니다. 대부분의네트워크에서는프린터가무선액세스지점 ( 무선라우터 ) 의 30m(100ft) 이내에있어야합니다. 프린터드라이버가컴퓨터에설치되어있는지확인합니다. 컴퓨터및프린터가동일한무선네트워크에연결되어있는지확인합니다. Mac 의경우무선라우터에서 Bonjour 를지원하는지확인합니다. 무선라우터를재시작합니다. 9

10 English...1 Bahasa Indonesia...4 한국어...7 ไทย...10 繁體中文 Tiếng Việt

11

12 8. 12

13 LaserJet Pro M203 入門指南 English...1 Bahasa Indonesia...4 한국어...7 ไทย 重要事項 : 繁體中文 Tiếng Việt 首先, 依照印表機硬體設定海報的步驟 1-3 進行後, 再繼續執行步驟 4 4. 控制面板上的初始設定 在印表機控制面板上, 先檢查 LED 狀態, 再開始進行軟體安裝 5. 選擇連線方法 直接在印表機與電腦之間連接的 USB 連線使用 A 對 B 型 USB 纜線 Windows 1. 請勿在安裝軟體之前連接 USB 纜線 安裝程序會在適當時間提示您連接纜線 如果纜線已經連接, 請在安裝提示告訴您連接纜線時重新啟動印表機 2. 繼續執行 6. 下載與安裝軟體 OS X 1. 對於 OS X, 先連接電腦與印表機之間的 USB 纜線, 再進行軟體安裝 2. 繼續執行 6. 下載與安裝軟體 無線網路連線 ( 僅限無線機型 ) 開始安裝前, 先確認無線存取點運作正常 確定印表機 路由器和電腦皆已開啟電源, 而且電腦也已連接至印表機將要連接的同一個無線網路 1. 將光碟放入 CD-ROM 光碟機, 瀏覽至 setup.exe 並按兩下 印表機連線對話方塊出現時, 選擇 Make a wireless connection to the device( 與裝置進行無線連線 ) 2. 依照螢幕上的指示進行 3. 選擇軟體偵測到的印表機 如果安裝程式偵測不到印表機, 請手動輸入印表機的 IP 位址以繼續進行安裝 附註 : 列印組態頁以找出印表機 IP 位址 在印表機控制面板上, 按住 繼續 / 取消 按鈕 5 秒鐘後, 再放開 繼續 / 取消 按鈕以列印組態頁 IP 位址會在組態頁的 Network Information ( 網路資訊 ) 區段中列出 有線 ( 乙太網路 ) 網路連線 ( 選用 ) 使用標準網路線 1. 將網路線連接至印表機與網路 等待幾分鐘, 讓印表機取得網路位址 2. 繼續執行 6. 下載與安裝軟體 手動設定 IP 位址 如需有關如何手動設定 IP 位址的詳細資訊, 請參閱印表機使用指南 13

14 6. 下載與安裝軟體 方法 1: 下載 HP Easy Start(Windows 和 OS X) 1. 前往 123.hp.com/laserjet, 然後按一下 Download( 下載 ) 2. 依照螢幕上的指示和提示, 將檔案儲存至電腦 3. 從儲存軟體檔案的資料夾啟動軟體檔案 方法 2: 從印表機支援網站下載 (Windows 和 OS X) 1. 前往 2. 選擇 Software and drivers( 軟體與驅動程式 ) 3. 下載適用於您印表機型號和作業系統的軟體 4. 從儲存軟體檔案的資料夾啟動軟體檔案 方法 3: 從印表機光碟安裝 ( 僅限 Windows) 1. 將印表機光碟插入電腦中 2. 依照螢幕上的指示安裝軟體 如需詳細資訊, 請參閱印表機光碟上的 安裝注意事項 安裝注意事項 如需印表機所需軟體的詳細資訊, 請參閱印表機光碟上的 安裝注意事項 檔案 7. 行動列印 ( 選用 ) 7.2 Wi-Fi Direct( 僅限無線機型 ) 7.1 將裝置連接至無線網路 若要從手機或平板電腦列印, 請將裝置連接到與印表機相同的無線網路 Apple ios 裝置 (AirPrint): 開啟要列印的項目, 並選擇動作圖示 選擇列印, 選擇印表機, 然後選擇列印 Android 裝置 (4.4 或更新版本 ): 開啟要列印的項目, 並選擇選單按鈕 選擇列印, 選擇印表機, 然後選擇列印 某些裝置需要從 Google Play 商店下載 HP Print Service 外掛應用程式 Windows Phone: 從 Windows 市集下載 HP AiO Remote 應用程式 進一步了解行動列印 如需有關這些和其他作業系統 (Chrome/Google 雲端列印 ) 的更多資訊, 請前往 或掃描以下的 QR 碼 Wi-Fi Direct 可讓具備 Wi-Fi 功能的裝置 ( 例如智慧型手機 平板電腦或電腦 ) 在沒有使用無線路由器或存取點的情況下, 直接與印表機進行無線網路連線 連接至印表機的 Wi-Fi Direct 訊號, 方法與您將具備 Wi-Fi 功能的裝置連接至新的無線網路或熱點一樣 啟用 Wi-Fi Direct 依照下列步驟, 在 HP 內嵌式 Web 伺服器 (EWS) 中啟用 HP Web 服務 : 1. 將印表機連接至網路, 並列印組態頁以取得印表機 IP 位址 附註 : 若要手動設定 IP 位址或是使用自動設定方式, 請參閱使用指南中的 設定網路產品 2. 開啟網頁瀏覽器, 在網址列中輸入印表機 IP 位址, 然後按下 Enter IP 位址範例 : 在 HP EWS 中, 選擇網路標籤 4. 選擇 Wi-Fi Direct 設定頁面, 再選擇開啟, 然後按一下套用 14

15 8. 設定 HP eprint via ( 選用 ) 使用 HP eprint via , 您只要在任何具備電子郵件功能的裝置上, 將文件當做電子郵件附件傳送至印表機的電子郵件地址即可列印該文件, 即使您使用的裝置不在同一個網路上也沒問題 若要使用 HP eprint via , 印表機必須符合以下要求 : 印表機必須連線到有線或無線網路, 且必須能夠存取網際網路 印表機必須啟用 HP Web 服務, 而且您必須已向 HP Connected 註冊印表機 啟用 HP Web 服務 ( 僅限無線機型 ) 1. 將印表機連接至 HP 內嵌式 Web 伺服器 (EWS) 後, 列印組態頁並找出印表機 IP 位址 2. 開啟電腦上的網頁瀏覽器, 並在網址列中輸入印表機 IP 位址 HP EWS 隨即開啟 3. 按一下 HP Web 服務標籤 如果網路使用 Proxy 伺服器, 請執行以下動作 : 選擇 Proxy 設定標籤 選擇如果網路使用 Proxy 伺服器存取網際網路, 請核取此方塊核取方塊 在 Proxy 伺服器欄位中, 輸入 Proxy 伺服器位址和連接埠號碼, 然後按一下套用按鈕 4. 選擇 HP Web 服務標籤, 然後按一下啟用按鈕 印表機會設定網際網路連線, 然後出現訊息表示即將列印資訊頁 5. 按一下 OK 按鈕 隨即列印 eprint 頁面 在 eprint 頁面上, 尋找自動指派給印表機的電子郵件地址 疑難排解 使用指南 使用指南包含印表機使用方式及疑難排解資訊 這可在印表機光碟或網路上取得 : 1. 前往 2. 從清單選擇印表機或類別, 然後按一下 User Guides( 使用指南 ) 檢查韌體更新 1. 前往 2. 從清單選擇印表機或類別, 然後按一下 Drivers( 驅動程式 ) 3. 選擇作業系統, 然後按一下 Next( 下一步 ) 按鈕 4. 選擇 Firmware( 韌體 ), 然後按一下 Download( 下載 ) 按鈕 其他支援資源如需包含印表機所有相關資訊的 HP 說明, 請前往 解決問題 尋找進階組態設定指示 下載軟體更新 加入支援論壇 尋找保固及法規資訊 存取行動列印資源 解析錯誤碼訊息 ( 第一次使用 ) 指示燈狀態注意指示燈閃爍 動作將紙張裝入紙匣 無線網路連線 ( 僅限無線機型 ) 確認印表機和無線路由器已開啟且接通電源 此外, 確定無線開關已開啟 確認印表機位於無線網路範圍內 對多數網路而言, 印表機必須是在距離無線存取點 ( 無線路由器 )30 公尺 (100 英呎 ) 以內的位置 確認電腦已安裝列印驅動程式 確認電腦和印表機連接至相同的無線網路 若是使用 Mac, 請確認無線路由器支援 Bonjour 重新啟動無線路由器 15

16 English...1 Bahasa Indonesia...4 한국어...7 ไทย...10 繁體中文 Tiếng Việt

17

18 8. 18

19

20 Copyright 2017 HP Development Company, L.P. Reproduction, adaptation or translation without prior written permission is prohibited, except as allowed under the copyright laws. The information contained herein is subject to change without notice. The only warranties for HP products and services are set forth in the express warranty statements accompanying such products and services. Nothing herein should be construed as constituting an additional warranty. HP shall not be liable for technical or editorial errors or omissions contained herein. Trademark Credits Windows is a U.S. registered trademark of Microsoft Corporation. Apple and the Apple logo are trademarks of Apple Inc., registered in the U.S. and other countries. OS X is a trademark of Apple Inc., registered in the U.S. and other countries. AirPrint is a trademark of Apple Inc., registered in the U.S. and other countries. FCC Regulations This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio-frequency energy. If this equipment is not installed and used in accordance with the instructions, it may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, correct the interference by one or more of the following measures: Reorient or relocate the receiving antenna. Increase separation between equipment and receiver. Connect equipment to an outlet on a circuit different from that to which the receiver is located. Consult your dealer or an experienced radio/tv technician. Any changes or modifications to the product that are not expressly approved by HP could void the user s authority to operate this equipment. Use of a shielded interface cable is required to comply with the Class B limits of Part 15 of FCC rules. For more regulatory information, see the electronic user guide. HP shall not be liable for any direct, indirect, incidental, consequential, or other damage alleged in connection with the furnishing or use of this information.