English Introduction Congratulations on your purchase and welcome to Philips! To fully benefit from the support that Philips offers, register your pro

1 Register your product and get support at www.philips.com/welcome HD9388, HD9386, HD9384, HD9380 4222.005.0307.1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21

English Introduction Congratulations on your purchase and welcome to Philips! To fully benefit from the support that Philips offers, register your product at www.philips. com/welcome. General description (Fig. 1) 1 Lid 2 Spout 3 Water level indicator 4 Lid release button 5 Base 6 Base connector 7 Cord storage facility 8 Mains plug 9 Black tea button 10 Green tea button 11 Herbal/fruit tea button 12 Instant coffee button 13 40ºC button 14 KEEP WARM button 15 Instant soup/hot chocolate button 16 Personal setting button 17 Rooibos tea button 18 Arrow buttons 19 Calc light 20 Display Important Read this user manual carefully before you use the appliance and save it for future reference. Danger Do not immerse the kettle or the base in water or any other liquid. Warning Check if the voltage indicated on the appliance corresponds to the local mains voltage before you connect the appliance. Do not use the appliance if the plug, the mains cord, the base or the appliance itself is damaged. If the mains cord is damaged, you must have it replaced by Philips, a service centre authorised by Philips or similarly qualified persons in order to avoid a hazard. This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety. Children should be supervised to ensure that they do not play with the appliance. Keep the mains cord out of the reach of children. Do not let the mains cord hang over the edge of the table or worktop on which the appliance stands. Excess cord can be stored in or around the base of the appliance. Do not place the appliance on an enclosed surface (e.g. a serving tray), as this could cause water to accumulate under the appliance, resulting in a hazardous situation. Hot water can cause serious burns. Be careful when the kettle contains hot water. Do not touch the body of the kettle during and some time after use, as it gets very hot. Always lift the kettle by its handle. Never fill the kettle beyond the maximum level indication. If the kettle has been overfilled, boiling water may be ejected from the spout and cause scalding. Do not remove the lid while the water is heating up. Be careful when you remove the lid immediately after the water has boiled: the steam that comes out of the kettle is very hot. Only use the kettle in combination with its original base. Caution Only connect the appliance to an earthed wall socket. Always place the base and the kettle on a dry, flat and stable surface. The kettle is only intended for heating up and boiling water. Do not use it to heat up soup or other liquids or jarred, bottled or tinned food. When you select a temperature below 100ºC, the water is not boiled (sterilised) first, but is heated up directly to the temperature of the selected preset button. Always make sure you fill the kettle at least up to the 1-cup indication (0.25l) to prevent the kettle from boiling dry. Depending on the hardness of the water in your area, small spots or stains may appear on the heating element of your kettle when you use it. This phenomenon is the result of scale build-up on the heating element and on the inside of the kettle over time. The harder the water, the faster scale builds up. Scale can occur in different colours. Although scale is harmless, too much scale can influence the performance and durability of your kettle. Descale your kettle regularly by following the instructions given in chapter Cleaning and descaling. Some condensation may appear on the base of the kettle. This is perfectly normal and does not mean that the kettle has any defects. This appliance is intended to be used in household and similar applications such as: 1 staff kitchen areas in shops, offices and other working environments; 2 farm houses; 3 by clients in hotels, motels and other residential type environments; 4 bed and breakfast type environments. Boil-dry protection This kettle is equipped with boil-dry protection. The boil-dry protection automatically switches off the kettle if it is accidentally switched on when there is no water or not enough water in it. Fill the kettle with approx. 1 litre of water. Leave the kettle off the base for 1 minute and then place it on the base. The kettle is now ready for use again. Electromagnetic fields (EMF) This Philips appliance complies with all standards regarding electromagnetic fields (EMF). If handled properly and according to the instructions in this user manual, the appliance is safe to use based on scientific evidence available today. Before first use 1 Remove stickers, if any, from the base or the kettle. 2 Place the base on a dry, stable and flat surface. 3 To adjust the length of the cord, wind part of it around the cord storage facility in the bottom of the base (Fig. 2). 4 Rinse the kettle with water. 5 Fill the kettle with water up to the MAX indication and let the water boil once (see chapter Using the appliance ). 6 Pour out the hot water and rinse the kettle once more. Changing the frequency of the descaling reminder The calc light lights up after a fixed amount of usages, based on average water hardness. You can change this frequency by setting a lower or higher water hardness or you can completely switch off the descaling reminder. 1 Press the herbal tea/fruit tea button and the personal setting button at the same time. (Fig. 3) Both buttons and the display light up. The display shows A, for average (Fig. 4). 2 Use the arrow buttons to adjust the water hardness (Fig. 5). You can adjust the hardness to H, for high, or L for low. 3 Press the herbal tea/fruit tea button and the personal setting button at the same time again to confirm the new setting. Note: If you do not confirm the new setting, the change is not stored. Switching off the descaling reminder Follow the steps in section Changing the frequency of the descaling reminder and select - to switch off the descaling reminder. Using the appliance 1 Press the lid release button (1). The lid opens automatically (2) (Fig. 6). 2 Fill the kettle with the desired amount of water (Fig. 7). Note: You can also fill the kettle through the spout. 3 Close the lid (Fig. 8). 4 Place the kettle on its base and put the plug in the wall socket (Fig. 9). The appliance is now ready for use. Heating up water with preset buttons Different hot drinks require different temperatures to taste their best. With the preset buttons on the base, you can choose the right temperature for your favourite hot drink. To make sure the appliance accurately* heats up the water to the set temperature, fill the kettle with at least 0.25l water. * This kettle has been designed to achieve maximum temperature accuracy. However, the actual temperature of the water may deviate slightly from the indicated temperature.

HD9380/HD9384: There are 4 buttons that represent different hot drinks: black tea (100ºC), green tea (80ºC), herbal/fruit tea (100ºC) and instant coffee (90ºC). There is also a 40ºC button and a KEEP WARM button. (Fig. 10) HD9386: There are 5 buttons that represent different hot drinks: black tea (100ºC), green tea (80ºC), herbal/fruit tea (100ºC), instant coffee (90ºC) and instant soup/hot chocolate (95ºC). There is also a personal setting button (40ºC-100ºC). HD9388: There are 4 buttons that represent different tea types: black tea (100ºC), green tea (80ºC), herbal/fruit tea (100ºC) and rooibos tea (100ºC). There is also a personal setting button (60ºC-100ºC) and a KEEP WARM button. Note: The control panel of type HD9388 is shown in the following pictures. The control panels of types HD9386, HD9384 and HD9380 look different, but the preset buttons work in the same way. Types HD9388 and HD9386 have a display, types HD9384 and HD9380 do not have a display. 1 Press one of the preset buttons. HD9386/HD9388 only: When you press a preset button, the temperature of the selected button is shown on the display for 3 seconds (Fig. 11). The water starts heating to the temperature of the selected preset button. While the water is heated, the light ring around the selected button slowly pulsates and the temperature rise is shown on the display (HD9386/HD9388 only) until the water has reached the desired temperature (Fig. 12). If the current temperature of the water in the kettle is higher than the temperature of the selected preset button, the light ring does not pulsate, but flashes 3 times to indicate that this button cannot be operated (Fig. 13). Note: You can deactivate the appliance by pressing the button again or by removing the kettle from the base. 2 The kettle heats the water to the temperature of the selected preset button. When the water has reached the set temperature, you hear an audible signal. The light ring around the selected button stops pulsating and lights up continuously (Fig. 14). Note: The audible signal is repeated as a reminder after 2 minutes. Note: You can select a different type of hot drink by pressing a different preset button while the kettle is operating. This is only possible if the temperature of the water is still below the temperature of the newly pressed button. Personal setting button (HD9386/HD9388 only) You can use the personal setting button to set a temperature that you prefer between 40ºC and 100ºC (HD9386) or between 60ºC and 100ºC (HD9388) in steps of 5ºC. Note: You cannot set a lower temperature than the temperature of the water in the kettle. 1 Press the personal setting button (Fig. 15). The display and the two arrow buttons light up. The last used temperature is shown on the display. Note: When you use the personal setting button for the first time, the lowest temperature is shown. 2 Adjust the temperature with the arrow buttons (Fig. 16). 3 Press the personal setting button again to confirm the temperature. The display flashes twice to confirm the temperature. The display shows the temperature rise of the water and the light ring around the personal setting button slowly pulsates until the water has reached the set temperature (Fig. 17). Note: If you do not change the temperature and do not press the personal setting button to confirm, the C icon flashes to remind you that the temperature can be adjusted. Note: If the water is already hot, you cannot set a temperature lower than the temperature of the water in the kettle. In that case, the left arrow button goes out to indicate that you cannot select a lower temperature. Note: When you have used the personal setting button, the temperature of this button is stored as the default temperature for the next use. Keeping water warm You can use the keep-warm function to keep water warm for 30 minutes at the temperatures of the different preset buttons (40 C, 80 C, 90 C, 95 C or 100 C) or the personal setting button. Note: Only use the keep-warm function in combination with a preset button or the personal setting button. Only use the keep-warm function when there is at least 0.25l water in the kettle. If there is too little water in the kettle, the kettle may switch off before the 30 minutes have elapsed to protect the heating element. Keeping water warm at a desired temperature 1 Press a preset button or the personal setting button (HD9386/ HD9388 only) to set the desired temperature (see sections Heating up water with preset buttons and Personal setting button in this chapter). 2 Press the KEEP WARM button (Fig. 18). When the kettle heats up the water to keep it at the selected temperature, the light ring around the KEEP WARM button lights up continuously. The selected temperature is shown on the display (HD9386/HD9388 only). When the water has reached the selected temperature, the light ring around the KEEP WARM button slowly pulsates until the keep-warm function is cancelled or switches off automatically after 30 minutes. Note: If you press the KEEP WARM button before you press a preset button or the personal setting button (HD9386/HD9388 only), nothing happens. If you have just prepared hot water, you can press the same preset button or the personal setting button (HD9386/HD9388 only) again and then press the KEEP WARM button. 3 The kettle keeps the water warm for 30 minutes. After 30 minutes, you hear an audible signal and the appliance switches off automatically. Note: You can stop the keep-warm process at any time. To do so, press the KEEP WARM button again, press the selected preset button or the personal setting button (HD9386/HD9388 only) or remove the kettle from the base. Note: If you remove the kettle from the base, the set keep-warm temperature is lost. Note: If you press another preset button or the personal setting button (HD9386/HD9388 only) while the keep-warm function is activated, the keepwarm function switches off and the kettle starts heating up the water to the temperature of the preset button or the personal setting button. Note: If the keep-warm function has not been activated, the appliance switches off automatically after 5 minutes of inactivity. Cleaning and descaling Always unplug the base before you clean it Always remove the kettle from the base before you clean the kettle. Never immerse the kettle or its base in water. Never use scouring pads, abrasive cleaning agents or aggressive liquids such as petrol or acetone to clean the appliance. Cleaning the kettle and the base 1 Clean the outside of the kettle and the base with a soft cloth moistened with warm water and some mild cleaning agent. Caution: Do not let the moist cloth come into contact with the cord, the plug and the connector of the base. Cleaning the filter Scale is not harmful to your health but it may give your drink a powdery taste. The anti-scale filter prevents scale particles from ending up in your drink. Clean the single-action filter regularly in the following way: 1 Take the filter out of the kettle (Fig. 19). 2 Gently clean the filter with a soft nylon brush. 3 Slide the filter back into the kettle. Note: HD9386/HD9388 only: The filter at the bottom of the kettle cannot be removed. You can clean this filter by descaling the kettle, see sections Descaling the kettle below. Descaling the kettle (HD9380/HD9384) Regular descaling prolongs the lifetime of the kettle. In case of normal use (up to 5 times a day), the following descaling frequency is recommended: Once every 6 months for areas with low water hardness. Once every 3 months for areas with average water hardness.

Once every month for areas with high water hardness. 1 Fill the kettle with white vinegar (8% acetic acid) up to one quarter of the MAX indication. 2 Add water to the MAX indication. 3 Press the green tea button to heat up the water to 80ºC and then press the KEEP WARM button. 4 Empty the kettle after 30 minutes and rinse the inside thoroughly. 5 Repeat the descaling procedure if there is still some scale in the kettle. Note: You can also use an appropriate descaler. In that case, follow the instructions on the package of the descaler. Descaling the kettle (HD9386/HD9388) If the kettle needs to be descaled, the calc light lights up on the display of the base. 1 Fill the kettle with white vinegar (8% acetic acid) up to one quarter of the MAX indication. 2 Add water to the MAX indication. 3 To start the descaling process, press the black tea button and the personal setting button at the same time (Fig. 20). The kettle heats up the water to 80ºC. During the descaling process, the calc light slowly pulsates until the descaling process has finished. The display counts down the time of the descaling process (30 minutes) in steps of 5 minutes. The time on the display slowly pulsates. When the descaling process is finished, you hear an audible signal and the appliance switches off automatically. 4 Follow steps 4 and 5 in section Descaling the kettle (HD9380/ HD9384) above. Note: If you take the kettle off the base before the descaling process is finished, the appliance switches off automatically. You can also deactivate the descaling process by pressing any of the preset buttons. Note: If you do not descale the kettle, the calc light lights up the next 5 times you use the kettle. Storage To store the cord, wind it around the cord storage facility in the bottom of the base (Fig. 2). Ordering accessories To purchase accessories for this appliance, please visit our online shop at www.shop.philips.com/service. If the online shop is not available in your country, go to your Philips dealer or a Philips service centre. If you have any difficulties obtaining accessories for your appliance, please contact the Philips Consumer Care Centre in your country. You find its contact details in the worldwide guarantee leaflet. Environment Do not throw away the appliance with the normal household waste at the end of its life, but hand it in at an official collection point for recycling. By doing this, you help to preserve the environment (Fig. 21). Guarantee and service If you need service or information or if you have a problem, please visit the Philips website at www.philips.com/support or contact the Philips Consumer Care Centre in your country. You find its phone number in the worldwide guarantee leaflet. If there is no Consumer Care Centre in your country, go to your local Philips dealer. Troubleshooting This chapter summarises the most common problems you could encounter with the appliance. If you are unable to solve the problem with the information below, visit www.philips.com/support for a list of frequently asked questions or contact the Consumer Care Centre in your country. Signal The light ring around one preset button lights up while the other light rings are off. The light ring of the preset button I pressed flashes 3 times. Meaning/solution After the water has reached the set temperature, the light of the selected preset button stays on for 5 minutes. The temperature of the water is higher than the temperature of the selected preset button. Signal E5 appears on the display. The kettle beeps. Problem I cannot set the desired temperature. I try to switch on the kettle but it switches off automatically. The kettle switches off automatically when the keepwarm function is active. 한국어 Meaning/solution The kettle is out of order. Contact an authorised Philips service centre or the Consumer Care Centre in your country. The water has reached the set temperature. Possible solution The current temperature of the water in the kettle is probably higher than the temperature you want to set. You can add cold water to the kettle. If you wish to reheat the water immediately, you can only select 100ºC. When there is no water in the kettle, the boildry protection trips and the kettle switches off automatically. You may need to put more water in the kettle (at least 0.25 litres). The kettle is not placed on its base correctly. Remove the kettle from the base and correctly place it on the base again. The kettle keeps the water warm for 30 minutes and then switches off automatically. To keep the water warm longer, press the KEEP WARM button again after it has finished. 소개필립스제품을구입해주셔서감사합니다! 필립스가드리는지원혜택을받으실수있도록 www.philips.co.kr 에서제품을등록하십시오. 각부의명칭 ( 그림 1) 1 뚜껑 2 주입구 3 수위표시기 4 뚜껑열림버튼 5 받침대 6 받침대연결부 7 코드보관함 8 전원플러그 9 홍차버튼 10 녹차버튼 11 허브차 / 과일차버튼 12 인스턴트커피버튼 13 40ºC 버튼 14 보온버튼 15 즉석수프 / 핫초코버튼 16 온도설정버튼 17 루이보스차버튼 18 화살표버튼 19 석회질세척 20 표시창 중요사항본제품을사용하기전에이사용설명서를주의깊게읽고나중에참조할수있도록잘보관하십시오. 위험 주전자나받침대를물또는다른액체에담그지마십시오. 경고 제품에전원을연결하기전에, 제품에표시된전압과사용지역의전압이일치하는지확인하십시오. 플러그, 전원코드, 받침대또는제품자체가손상된경우에는본제품을사용하지마십시오. 전원코드가손상된경우, 안전을위해필립스서비스센터또는필립스서비스지정점에의뢰하여교체하십시오. 신체적인감각및정신적인능력이떨어지거나경험과지식이풍부하지않은성인및어린이는혼자제품을사용하지말고제품사용과관련하여안전에책임질수있도록지시사항을충분히숙지한사람의도움을받으십시오. 어린이가제품을가지고놀지못하도록지도해주십시오.

전원코드는어린이의손에닿지않는곳에보관하십시오. 제품이올려져있는식탁이나조리대의가장자리로전원코드가흘러내리지않도록하십시오. 여분의전원코드는받침대안에보관할수있습니다. 쟁반처럼주변부가바닥을에워싸는표면에제품을놓지마십시오. 제품아래에물이고여매우위험할수있습니다. 뜨거운물은심각한화상을일으킬수있습니다. 전기주전자에뜨거운물이있을경우에는주의하십시오. 물이가열중이거나물을사용한직후에는전기주전자가매우뜨거우므로신체에접촉하지않도록하십시오. 항상손잡이부분을잡고전기주전자를들어올리십시오. 전기주전자에최대량표시인 MAX 눈금이상물을넣지마십시오. 물을너무많이넣을경우, 끓는물이배출구밖으로넘쳐화상을입을수있습니다. 물이끓는동안에는뚜껑을열지마십시오. 물이끓고난다음바로뚜껑을열경우, 전기주전자에서나오는수증기가매우뜨거우므로주의하십시오. 전기주전자는반드시원래의받침대를사용하십시오. 주의 제품은반드시접지된벽면콘센트에연결하십시오. 전기주전자와받침대는항상물기가없고, 평평하며안정된곳에놓으십시오. 본전기주전자는물을가열하고끓이는용도로만사용하는제품입니다. 수프나기타액체또는항아리, 병, 캔에든음식을조리하지마십시오. 100ºC 이하의온도를선택하면먼저물이끓지 ( 소독되지 ) 않고선택한프리셋버튼의온도까지만가열됩니다. 전기주전자가물이없는상태에서작동하는것을방지하기위해항상한컵표시선 (0.25리터) 이상물을채워야합니다. 지역에공급되는물의경도에따라, 제품사용중열판에작은반점이나얼룩이생길수있습니다. 이현상은열판이나제품내부에수차례석회질이쌓여서생긴결과입니다. 물의경도가높을수록, 석회질은더욱빨리생성되며여러가지색상으로나타날수있습니다. 석회질은유해하지는않지만, 너무많은석회질은제품의성능에영향을줄수도있습니다. 본사용설명서의 세척및석회질제거 란에서설명하는방법에따라정기적으로석회질을제거해주십시오. 전기주전자받침대에물방울이맺힐수있습니다. 이것은자연적인현상이며제품의이상이아닙니다. 본제품은가정및다음과같은유사환경에서사용하도록설계되었습니다. 1 매장, 사무실및기타작업환경내직원용탕비실 2 주거시설 3 호텔및기타숙박시설 4 민박시설건조상태가열방지기능이전기주전자에는건조상태가열방지기능이장착되어있습니다. 전기주전자에물이없거나충분하지않을때실수로전원을켜더라도이장치가자동으로주전자의전원을차단시킵니다. 약 1 리터의물을채운다음 1분간받침대에서주전자를내려놓았다가받침대에다시놓으면, 건조상태가열방지기능이해지됩니다. 이후에전기주전자를바로사용할수있습니다. EMF( 전자기장 ) 이필립스제품은 EMF( 전자기장 ) 와관련된모든기준을준수합니다. 이사용설명서의지침에따라적절하게취급할경우이제품은안전하게사용할수있으며이는현재까지의과학적증거에근거하고있습니다. 최초사용전 1 받침대또는전기주전자에스티커가붙어있을경우모두제거하십시오. 2 받침대는물기가없고안정적이며평평한곳에놓으십시오. 3 전원코드를받침대바닥의코드보관함주위에감아길이를조절하십시오 ( 그림 2). 4 전기주전자를물로헹구십시오. 5 전기주전자의 MAX 눈금까지물을채운다음한번끓여주십시오. ( 제품사용 란참조 ) 6 뜨거운물을버리고전기주전자를다시한번물로헹구십시오. 석회질제거알림주기변경평균물경도를기준으로일정횟수를사용하고나면석회질제거표시등이켜집니다. 경도를낮게또는높게설정하여주기를변경하거나석회질제거알림기능자체를해제할수도있습니다. 1 허브차 / 과일차버튼과온도설정버튼을동시에누릅니다. ( 그림 3) 두버튼과디스플레이모두켜집니다. 디스플레이에평균이란뜻의 A가표시됩니다 ( 그림 4). 2 화살표버튼을이용하여물의경도를조정합니다 ( 그림 5). 경도가높으면 H, 낮으면 L 에맞춥니다. 3 다시허브차 / 과일차버튼과온도설정버튼을동시에눌러새로운설정을확인합니다. 참고 : 새로운설정을확인하지않으면변경내용이저장되지않습니다. 석회질제거알림끄기 석회질제거알림주기변경 란의단계를따라석회질제거알림끄기를선택합니다. 제품사용 1 뚜껑열림버튼을누릅니다. (1) 뚜껑이자동으로열립니다. (2) ( 그림 6) 2 전기주전자에필요한만큼의물을채웁니다 ( 그림 7). 참고 : 전기주전자의주입구를통해물을채울수도있습니다. 3 뚜껑을닫으십시오 ( 그림 8). 4 전기주전자를받침대에놓고플러그를벽면콘센트에꽂으십시오 ( 그림 9). 이제제품을사용하실수있습니다. 프리셋버튼으로물끓이기따뜻한음료를이상적으로즐길수있는온도는각각다릅니다. 받침대의프리셋버튼으로적정온도를선택하여최고의맛을음미하세요. 설정한온도로물이정확히 * 데워지도록전기주전자를최소한약 0.25리터이상의물로채우십시오. * 이전기주전자는최대한정확한온도로데워지도록설계되어있지만, 실제물의온도는표시된온도와약간다를수있습니다. HD9380/HD9384: 홍차 (100ºC), 녹차 (80ºC), 허브차 / 과일차 (100ºC), 인스턴트커피 (90ºC) 의 4가지따뜻한음료버튼이있습니다. 40ºC 버튼과보온버튼도있습니다. ( 그림 10) HD9386: 홍차 (100ºC), 녹차 (80ºC), 허브차 / 과일차 (100ºC), 인스턴트커피 (90ºC), 즉석수프 / 핫초코 (95ºC) 의 5가지따뜻한음료버튼이있습니다. 온도설정버튼 (40ºC~100ºC) 도있습니다. HD9388: 홍차 (100ºC), 녹차 (80ºC), 허브차 / 과일차 (100ºC), 루이보스차 (100ºC) 의 4가지차선택버튼이있습니다. 온도설정버튼 (60ºC~100ºC) 과보온버튼도있습니다. 참고 : 그림은 HD9388의제어판입니다. HD9386, HD9384, HD9380 모델의제어판은모양은달라도프리셋버튼의작동원리는같습니다. HD9388, HD9386 모델에는디스플레이가있는반면 HD9384, HD9380 모델에는디스플레이가없습니다. 1 프리셋버튼중하나를누릅니다. HD9386/HD9388 모델만해당 : 프리셋버튼을누르면선택한버튼의온도가디스플레이에 3초간표시됩니다 ( 그림 11). 선택한프리셋버튼의온도로물이가열되기시작합니다. 물이끓는동안선택한버튼주위의표시등이천천히깜박이며올라가는온도가디스플레이에표시됩니다.(HD9386/HD9388 모델만해당 ) ( 그림 12) 전기주전자에담긴물의현재온도가선택한프리셋버튼의온도보다높은경우표시등이깜박이는대신 3번빠르게깜박여이버튼이작동할수없음을알려줍니다 ( 그림 13). 참고 : 버튼을다시누르거나전기주전자를받침대에서들었다가다시놓으면기능이해제됩니다. 2 전기주전자가선택한프리셋버튼온도까지물을데웁니다. 물이설정온도에도달하면신호음이들립니다. 선택한버튼주위의표시등이깜박임을멈추고계속켜져있습니다 ( 그림 14). 참고 : 신호음은 2분후에다시울립니다. 참고 : 전기주전자가작동하는동안프리셋버튼을바꿔서다른종류의음료를선택할수있습니다. 단, 물의온도가새로설정한온도보다낮은경우에만가능합니다. 온도설정버튼 (HD9386/HD9388 모델만해당 ) 온도설정버튼을이용하여 40ºC~100ºC로원하는온도를설정하거나 (HD9386), 60ºC~100ºC에서 5ºC 간격으로설정할수도있습니다 (HD9388). 참고 : 전기주전자물의현재온도보다낮은온도로설정할수없습니다. 1 온도설정버튼을누르십시오 ( 그림 15). 디스플레이와 2개의화살표버튼이켜집니다.

이전에사용한온도가디스플레이에표시됩니다. 참고 : 온도설정버튼을처음사용할때는가장낮은온도가표시됩니다. 2 화살표버튼으로온도를조절하십시오 ( 그림 16). 3 온도설정버튼을다시눌러온도를확인합니다. 디스플레이가두번깜박여온도를확인합니다. 디스플레이에물의온도가올라가는것이보이며, 설정한온도에도달할때까지온도설정버튼주위의표시등이천천히깜박입니다 ( 그림 17). 참고 : 온도를바꾸지않고온도설정버튼을눌러확인하지않으면 C 아이콘이깜박이며온도를설정하라고알려줍니다. 참고 : 전기주전자에있는물이이미데워졌다면그보다더낮게온도를설정할수없습니다. 이경우왼쪽화살표버튼의불이꺼지기때문에낮은온도를선택할수없습니다. 참고 : 사용한온도설정버튼의온도는다음사용할때기본온도로저장됩니다. 보온기능서로다른프리셋버튼의온도 (40 C, 80 C, 90 C, 95 C, 100 C) 나온도설정버튼의온도로 30분동안온도를유지하는보온기능도사용할수있습니다. 참고 : 보온기능은프리셋버튼이나온도설정버튼과함께만사용할수있습니다. 물이전기주전자에 0.25리터이상있을때에만보온기능을사용하십시오. 전기주전자에물이너무적으면열판을보호하기위해 30분전에전원이꺼집니다. 원하는온도로보온 1 프리셋버튼이나온도설정버튼 (HD9386/HD9388 모델만해당 ) 을눌러원하는온도를설정합니다 ( 이란의 프리셋버튼으로물끓이기 와 온도설정버튼 섹션참조 ). 2 보온버튼을누르십시오 ( 그림 18). 전기주전자가설정된온도까지물을데워유지할때에는보온버튼주위의표시등이계속켜져있습니다. 선택한온도가디스플레이에표시됩니다 (HD9386/HD9388 모델만해당 ). 물이설정한온도에도달하면보온기능이취소될때까지표시등주위의보온버튼이천천히깜박이거나 30분후에자동으로꺼집니다. 참고 : 프리셋버튼이나온도설정버튼 (HD9386/HD9388 모델만해당 ) 을누르기전에보온버튼을누르면, 기능이작동하지않습니다. 물을이미끓었다면, 같은프리셋버튼이나온도설정버튼 (HD9386/HD9388 모델만해당 ) 을다시누른후보온버튼을누릅니다. 3 전기주전자의보온기능은 30분동안유지됩니다. 30분후신호음이들리고전기주전자가자동으로꺼집니다. 참고 : 언제든보온상태를중단할수있습니다. 보온버튼을다시누르거나, 원하는프리셋버튼이나온도설정버튼 (HD9386/ HD9388 모델만해당 ) 을눌러도되고, 받침대에서전기주전자를분리해도보온기능작동이중단됩니다. 참고 : 받침대에서전기주전자를분리하면보온온도설정이초기화됩니다. 참고 : 보온기능이작동중일때다른프리셋버튼이나온도설정버튼 (HD9386/HD9388 모델만해당 ) 을누르면보온기능이꺼지고전기주전자는선택한프리셋버튼이나온도설정버튼의온도로물을끓이기시작합니다. 참고 : 보온기능을사용하지않은상태에서 5분간작동하지않으면제품이자동으로꺼집니다. 청소및스케일제거제품을청소하기전에는항상제품받침대의전원코드를뽑으십시오. 전기주전자를청소하기전에반드시받침대에서제품을분리하십시오. 전기주전자와받침대는절대로물에담그지마십시오. 제품을세척할때수세미, 연마성세제나휘발유, 아세톤과같은강력세제를사용하지마십시오. 전기주전자및받침대청소 1 전기주전자외부는순한세척액과따뜻한물을적신부드러운천을사용하여닦으십시오. 주의 : 코드, 플러그및받침대연결부에젖은천이닿지않도록주의하십시오. 필터세척석회질은몸에해롭지는않지만물을마시면약간의가루가섞인맛을느낄수도있습니다. 석회질제거필터는물을컵에따르기전에석회질입자를걸러줍니다. 싱글액션필터를다음과같이정기적으로청소하십시오. 1 전기주전자에서필터를꺼내십시오 ( 그림 19). 2 부드러운나일론브러시로필터를가볍게청소하십시오. 3 전기주전자에필터를원래대로밀어넣으십시오. 참고 : HD9386/HD9388 모델만해당 : 전기주전자바닥의필터는제거할수없습니다. 전기주전자의석회질을제거하여필터를청소할수있습니다. 아래 석회질제거 란을참조하십시오. 석회질제거 (HD9380/HD9384) 정기적으로석회질을제거하면제품의수명이연장됩니다. 일반적으로사용할경우 ( 하루최대 5번 ), 다음과같은주기로스케일을제거하십시오. 물의경도가낮은지역은 6개월에한번 물의경도가평균인지역은 3개월에한번 물의경도가높은지역은한달에한번 1 주전자에흰식초 ( 아세트산 8%) 를 MAX 표시선의 1/4 정도까지채우십시오. 2 MAX 표시선까지물을채우십시오. 3 녹차버튼을눌러 80ºC까지물을데운다음보온버튼을누릅니다. 4 30분후에전기주전자를비우고내부를깨끗이헹구십시오. 5 전기주전자의석회질이완전히제거될때까지반복합니다. 참고 : 석회질제거용세제를사용하여헹구셔도됩니다. 이런경우, 석회질제거용세제에명시되어있는사용지침을따르십시오. 석회질제거 (HD9386/HD9388) 전기주전자의석회질제거시기가되면, 받침대디스플레이의석회질제거표시등이깜박입니다. 1 주전자에흰식초 ( 아세트산 8%) 를 MAX 표시선의 1/4 정도까지채우십시오. 2 MAX 표시선까지물을채우십시오. 3 석회질제거를시작하려면홍차버튼과온도설정버튼을동시에누르십시오 ( 그림 20). 전기주전자가 80ºC로물을가열합니다. 석회질제거가끝날때까지석회질제거표시등이계속천천히깜박입니다. 디스플레이에서석회질제거시간 (30분) 이 5분간격으로내려갑니다. 디스플레이의시간이천천히깜박입니다. 석회질제거가완료되면신호음이울리고전기주전자가자동으로꺼집니다. 4 위의 석회질제거 (HD9380/HD9384) 란의 4, 5단계를따르십시오. 참고 : 석회질제거가완료되기전에전기주전자를받침대에서분리하면제품이자동으로꺼집니다. 프리셋버튼중아무것이나누르면석회질제거가해제됩니다. 참고 : 전기주전자의석회질제거를하지않으면전기주전자를 5번사용할때까지석회질제거표시등이켜집니다. 보관 전원코드는받침대바닥의코드보관함에감아서보관하십시오 ( 그림 2). 액세서리주문본제품의액세서리를주문하려면필립스웹사이트 www.philips. co.kr 을방문하십시오. 해당국가에서온라인쇼핑이불가능한경우필립스대리점이나필립스서비스센터에문의하십시오. 본제품의액세서리를구하기어려운경우에는필립스고객상담실로문의하십시오. 연락처정보는전세계제품보증서에기재되어있습니다. 환경 수명이다된제품을일반가정용쓰레기와함께버리지마시고지정된재활용수거장소에버리시면환경보호에동참하실수있습니다 ( 그림 21).

품질보증및서비스보다자세한정보가필요하거나사용상의문제가있을경우에는, 필립스전자홈페이지 (www.philips.com/support) 를방문하시거나필립스고객상담실로문의하십시오. 전국서비스센터안내는제품보증서를참조하십시오. *( 주 ) 필립스전자 : (02)709-1200 * 고객상담실 : (080)600-6600( 수신자부담 ) 문제해결이란은본제품을사용하면서가장일반적으로경험하게되는문제와그해결방법을제시합니다. 아래의정보로도문제를해결할수없는경우 www.philips.com/support 를방문하여자주묻는질문 (FAQ) 목록을참조하거나필립스고객상담실로문의하십시오. 신호 다른표시등은꺼져있는데프리셋버튼주위의표시등이켜집니다. 내가누른프리셋버튼의표시등이 3번깜박입니다. 디스플레이에 E5가나타납니다. 전기주전자에신호음이울립니다. 문제점 원하는온도로설정할수없습니다. 전기주전자의전원을켜려고했으나자동으로꺼집니다. 보온모드가작동중인데도전기주전자의전원이자동으로꺼집니다. 가능한해결책 원인 / 해결방법 물이설정한온도까지도달한후선택한프리셋버튼이 5분동안꺼지지않습니다. 물의온도가설정한프리셋버튼의온도보다더높습니다. 전기주전자가고장난경우입니다. 필립스서비스센터나필립스고객상담실로문의하십시오. 물이설정한온도까지도달한것입니다. 전기주전자에담긴물의현재온도가설정하려는온도보다높은경우입니다. 전기주전자에찬물을보충하십시오. 물을바로재가열하려면 100 c만선택할수있습니다. 전기주전자에물이없으면, 건조상태가열방지기능이작동하고제품이자동으로꺼집니다. 전기주전자에물을 0.25리터이상넣어야합니다. 전기주전자가받침대위에올바르게놓이지않았습니다. 전기주전자를받침대에서분리하여다시정확하게맞추십시오. 전기주전자는 30분동안보온을유지한후자동으로전원이꺼집니다. 완료된후에도다시한번보온버튼을누르면더오랫동안물을따뜻하게보관할수있습니다. 繁體中文 簡介感謝您購買本產品並歡迎加入飛利浦! 請於 www.philips.com/ welcome 註冊您的產品, 以善用飛利浦提供的支援 一般說明 ( 圖 1) 1 蓋子 2 壺嘴 3 水位顯示 4 開蓋按鈕 5 底座 6 底座接頭 7 電源線收納裝置 8 電源線插頭 9 紅茶按鈕 10 綠茶按鈕 11 花草 / 水果茶按鈕 12 即溶咖啡按鈕 13 40ºC 按鈕 14 保溫按鈕 15 即溶湯 / 熱可可按鈕 16 個人設定按鈕 17 Rooibos 茶按鈕 18 箭頭按鈕 19 除垢指示燈 20 顯示 重要事項在使用本產品前, 請先仔細閱讀本使用手冊, 並保留使用手冊以供日後參考 危險 切勿將此電動煮水器或底座浸泡在水中或其他液體中 警示 在您連接電源之前, 請檢查本地的電源電壓是否與產品所標示的電壓相符 如果插頭 電源線 底座或產品裝置本身有損傷時, 則請勿使用 如果電線損壞, 則必須交由飛利浦 飛利浦授權之服務中心, 或是具備相同資格的技師更換, 以免發生危險 基於安全考慮, 在缺乏監督及適當指示之下, 本產品不適用於孩童及任何身體 知覺 或心理功能障礙者, 或缺乏使用經驗及知識者 請勿讓孩童使用本產品或將本產品當成玩具 請勿讓兒童接觸電源線 請勿讓電源線懸掛在產品放置的餐桌或流理台邊緣 過長的電源線可以收藏或捲繞在底座 請勿將產品放在具阻絕性的表面 ( 如 : 托盤 ) 上, 因為這會導致產品下方積水, 產生危險的狀況 熱開水可能會造成嚴重燙傷, 電動煮水器中裝有熱水時請特別小心 使用期間或使用過後, 請勿碰觸電動煮水器機體, 因為機體非常熱 請務必使用握把提起電動煮水器 在電動煮水器中加水不得超過最高水位指標 如果加入過多的水, 開水可能會從壺口噴出並造成燙傷 煮沸開水時, 切勿取下壺蓋 在開水煮沸後立即取下壺蓋時請特別小心, 從電動煮水器冒出的蒸汽溫度極高 電動煮水器只能搭配原廠的底座使用 警告 只將產品連接到有接地的電源插座 請務必將底座及電動煮水器放置於乾燥 平整 穩固的表面 電動煮水器只能用來加熱或煮沸開水, 請勿將電動煮水器用來加熱湯類或其他液體 或瓶裝或罐頭食品 當您選擇低於 100ºC 的溫度時, 不會先煮沸水 ( 消毒 ), 而是直接加熱至所選之預設按鈕的溫度 請務必裝滿電動煮水器到至少 1 杯水指示 (0.25 公升 ), 以避免電動煮水器乾燒 根據您當地的自來水硬度, 在使用電動煮水器時, 加熱元件上可能會出現小斑點或污漬 這個現象是因為水垢隨著時間聚積在加熱元件及電動煮水器內側所致 水的硬度越大, 水垢聚積的速度越快 水垢可能會呈現不同的顏色 水垢雖然無害, 但太多的水垢會影響熱電動煮水器的性能和耐用性 請依照 清潔及去除水垢 單元的指示, 定期清除電動煮水器的水垢 在電動煮水器的底座可能會出現水珠凝結的現象 這是完全正常的情況, 不表示煮水器有任何瑕疵 本產品為居家用途設計, 而類似的應用包含 : 1 店家的員工廚房 辦公室與其他工作場所 ; 2 農舍 ;

3 供住宿的飯店 汽車旅館與其他居住場所 ; 4 擺設床位與供應早餐的空間 防乾燒保護裝置此電動煮水器內建防止乾燒的保護功能 如果電動煮水器中沒有水或水量不足, 卻又意外被開啟, 乾燒保護功能會自動關閉電動煮水器 請在電動煮水器中注入大約 1 公升的水量, 並將電動煮水器拿離底座 1 分鐘, 然後再放回底座 接著您可以再次使用電動煮水器 電磁波 (EMF) 本飛利浦產品符合電磁波 (Electromagnetic fields,emf) 所有相關標準 只要使用方式正確並依照本使用手冊之說明進行操作, 根據現有的科學研究資料, 使用本產品並無安全顧慮 第一次使用 1 請撕除底座或電動煮水器上的貼紙 ( 如果有 ) 2 請將底座放置在乾燥 穩固 且平整的表面 3 若要調整電線長度, 請將部分電線捲入底座底部的電線收納裝置 ( 圖 2) 4 請用清水清洗電動煮水器 5 在電動煮水器中加水到 MAX ( 最高 ) 刻度, 並將水煮沸一次 ( 請參閱 使用此產品 單元 ) 6 將熱水倒出並再次清洗電動煮水器 變更除垢提醒的頻率除垢指示燈會依據平均水質硬度, 在達到固定使用量後亮起 您可以設定較低或較高的水質硬度以變更此頻率, 或者您也可以完全關閉除垢提醒 1 同時按下花草 / 水果茶按鈕和個人設定按鈕 ( 圖 3) 隨後兩個按鈕和顯示螢幕皆亮起 顯示螢幕上會顯示 A, 代表平均 ( 圖 4) 2 使用箭頭按鈕調整水質硬度 ( 圖 5) 您可以將水質硬度調整為 H ( 硬度高 ), 或調整為 L ( 硬度低 ) 3 再次同時按下花草 / 水果茶按鈕和個人設定按鈕, 以確認新設定 注意 : 如果您不確認新設定, 則不會儲存變更 關閉除垢提醒請依照 變更除垢提醒的頻率 單元內的步驟, 並選擇關閉除垢提醒 使用此產品 1 按下開蓋按鈕 (1) 蓋子會自動開啟 (2) ( 圖 6) 2 在電動煮水器中注入理想的水量 ( 圖 7) 注意 : 您也可以經由注水口為電動煮水器裝水 3 蓋上蓋子 ( 圖 8) 4 將電動煮水器放在底座上, 並將插頭插到牆上的插座 ( 圖 9) 這時已可開始使用 以預設按鈕將水加熱不同的熱飲需要不同溫度, 才能獲得最美味的效果 使用底座的預設按鈕, 即可針對您喜愛的熱飲選擇正確溫度 請至少注入 0.25 公升的水, 以確保產品正確將水加熱至設定的溫度 * 此電動煮水器的設計為可達到最精確的溫度 但是, 水的實際溫度可能與標示的溫度稍有差異 HD9380/HD9384: 有代表不同熱飲的 4 種按鈕 : 紅茶 (100ºC) 綠茶 (80ºC) 花草/ 水果茶 (100ºC) 和即溶咖啡 (90ºC) 此外尚有 40ºC 按鈕和保溫按鈕 ( 圖 10) HD9386: 有代表不同熱飲的 5 種按鈕 : 紅茶 (100ºC) 綠茶 (80ºC) 花草/ 水果茶 (100ºC) 即溶咖啡 (90ºC) 和即溶湯 / 熱可可 (95ºC) 此外尚有個人設定按鈕 (40ºC-100ºC) HD9388: 有代表不同熱飲的 4 種按鈕 : 紅茶 (100ºC) 綠茶 (80ºC) 花草/ 水果茶 (100ºC) 和 Rooibos 茶 (100ºC) 此外尚有個人設定按鈕 (60ºC-100ºC ) 和保溫按鈕 注意 : HD9388 機型的控制面板如下列圖片所示 HD9386 HD9384 和 HD9380 機型的控制面板看來不同, 但是預設按鈕皆以相同方式運作 HD9388 和 HD9386 機型有顯示螢幕,HD9384 和 HD9380 機型則沒有顯示螢幕 1 按下其中一個預設按鈕 僅限 HD9386/HD9388: 當您按下預設按鈕時, 所選按鈕的溫度將會在顯示螢幕上顯示 3 秒 ( 圖 11) 隨即開始將水加熱至所選預設按鈕的溫度 在水加熱時, 所選按鈕周圍的指示燈會緩慢規律閃動, 顯示螢幕上則會顯示上升的溫度 ( 僅限 HD9386/HD9388), 直到水達到了理想的溫度為止 ( 圖 12) 如果電動煮水器的水溫高於所選預設按鈕的溫度, 指示燈將不會規律閃動, 而是會閃爍 3 次, 表示此按鈕無法操作 ( 圖 13) 注意 : 只要再次按下按鈕或從底座移除電動煮水器, 即可關閉電動煮水器 2 電動煮水器會將水加熱至所選預設按鈕的溫度 當水達到設定溫度時, 您會聽見訊號音 所選按鈕周圍的指示燈會停止規律閃動, 並持續亮起 ( 圖 14) 注意 : 訊號音會在 2 分鐘後再響一次, 以示提醒 注意 : 煮水器加熱時, 您可以按下不同按鈕, 選擇不同類型的熱飲 但重新按下之按鈕的溫度必須高於目前水溫 個人設定按鈕 ( 僅限 HD9386/HD9388) 您可以使用個人設定按鈕設定理想溫度, 溫度可介於 40ºC 和 100ºC (HD9386) 之間, 或介於 60ºC 和 100ºC (HD9388) 之間 ( 以 5ºC 為單位增減 ) 注意 : 您不可設定比壺中水溫更低的溫度 1 按下個人設定按鈕 ( 圖 15) 顯示螢幕和兩個箭頭按鈕亮起 顯示螢幕會顯示最後一次使用的溫度 注意 : 首次使用個人設定按鈕時, 將顯示最低溫度 2 使用箭頭按鈕調整溫度 ( 圖 16) 3 再按一次個人設定按鈕以確認溫度 顯示螢幕會閃爍兩次, 確認溫度 顯示螢幕將顯示水的上升溫度, 所選按鈕周圍的指示燈會緩慢規律閃動, 直到水溫達到了理想的溫度為止 ( 圖 17) 注意 : 如果您不變更溫度, 且不按下個人設定按鈕以確認, 則 C 圖示將會閃爍, 提醒您可以調整溫度 注意 : 如果水已經燒熱, 即不可設定比壺中水溫更低的溫度 若是這樣, 左箭頭按鈕將會熄滅, 表示您無法選擇更低的溫度 注意 : 在您使用了個人設定按鈕後, 將會儲存此按鈕的溫度, 作為下次使用的預設溫度 保持水溫您可以使用保溫功能, 持續 30 分鐘將水溫保持在各個不同預設按鈕 (40 C 80 C 90 C 95 C 或 100 C) 或個人設定按鈕的溫度 注意 : 保溫功能僅可搭配預設按鈕或個人設定按鈕使用 保溫功能只能在水位高於 0.25 公升時使用 如果壺中的水量太少, 電動煮水器可能會在 30 分鐘結束時關閉, 以保護加熱板 將水溫保持在理想的溫度 1 按下預設按鈕或個人設定按鈕 ( 僅限 HD9386/HD9388), 設定理想的溫度 ( 參閱本章的 以預設按鈕將水加熱 及 個人設定按鈕 單元 ) 2 按下保溫按鈕 ( 圖 18) 當電動煮水器將水加熱並保持在所選溫度時, 保溫按鈕周圍的指示燈會持續亮起 顯示螢幕上將顯示所選溫度 ( 僅限 HD9386/ HD9388) 當水溫達到所選溫度時, 保溫按鈕周圍的指示燈會緩慢規律閃動, 直到保溫功能取消, 或是保溫功能在 30 分鐘後自動關閉為止 注意 : 如果您在按下預設按鈕或個人設定按鈕前, 先按下保溫按鈕 ( 僅限 HD9386/HD9388), 將不會有任何反應 如果您已將水煮熱, 您可以再次按下相同的預設按鈕或個人設定按鈕 ( 僅限 HD9386/ HD9388), 然後再按下保溫按鈕 3 電動煮水器可保溫 30 分鐘 在 30 分鐘後, 您會聽到訊號音, 而產品會自動關閉 注意 : 您可以隨時停止保溫程序 如果要停止保溫, 請再次按下保溫按鈕 按下所選預設按鈕或個人設定按鈕 ( 僅限 HD9386/HD9388), 或將電動煮水器從底座移除 注意 : 如果您從底座移除電動煮水器, 設定的保溫溫度會遺失 注意 : 如果您在保溫功能啟動時, 按下其他預設按鈕或個人設定按鈕 ( 僅限 HD9386/HD9388), 保溫功能會關閉, 電動煮水器將開始將水加熱至預設按鈕或個人設定按鈕的溫度 注意 : 如果未啟動保溫功能, 產品會在閒置 5 分鐘後關閉

清潔及去除水垢進行清潔前, 請務必先拔除底座插頭 在您清潔電動煮水器前, 請務必將電動煮水器從底座移除 切勿將電動煮水器或其底座浸於水中 絕對不可使用鋼絲絨 磨蝕性的清潔劑或侵蝕性的液體 ( 例如汽油或丙酮 ) 清潔本產品 清潔電動煮水器及底座 1 使用軟質溼布, 配合溫水及溫和的清潔劑來清潔電動煮水器的外部 警告 : 請勿用濕布接觸電線 插頭及底座接頭 清潔濾網水垢對健康無害, 但可能會讓水產生帶有粉末的口感 水垢濾網可以避免讓您喝到水垢微粒 請依照下列方法定期清洗單效濾網 : 1 從壺中將整個濾網拿出 ( 圖 19) 2 以軟質尼龍刷輕輕清潔濾網 3 將濾網滑進煮水器 注意 : 僅限 HD9386/HD9388: 煮水器底部的濾網不可拆卸 您可以透過煮水器除垢程序清潔此濾網 請參閱下面的 清除電動煮水器的水垢 單元 清除電動煮水器的水垢 (HD9380/HD9384) 定期清除水垢將可延長電動煮水器的使用壽命 在正常使用情況下 ( 每天使用約 5 次 ), 建議依下列頻率定期去除水垢 : 水質較軟的地區每 6 個月一次 水質硬度中等的地區每 3 個月一次 水質較硬的地區每一個月一次 1 在水箱內倒入白醋 (8% 醋酸 ), 裝到 MAX ( 最高 ) 刻度的四分之一 2 加水到 MAX ( 最高 ) 刻度 3 按下綠茶按鈕, 將水加熱到 80ºC, 然後按下保溫按鈕 4 在 30 分鐘後將電動煮水器中的水倒光並徹底清洗水壺內部 5 如果仍然有部份水垢留在壺中, 請重複除垢程序 注意 : 您也可以使用適當的水垢清除劑 如果使用水垢清除劑, 請依照包裝上的指示使用 清除電動煮水器的水垢 (HD9386/HD9388) 當電動煮水器需要除水垢時, 基座顯示螢幕上的除垢指示燈將會亮起 1 在水箱內倒入白醋 (8% 醋酸 ), 裝到 MAX ( 最高 ) 刻度的四分之一 2 加水到 MAX ( 最高 ) 刻度 3 若要開始除垢程序, 請同時按下紅茶按鈕和個人設定按鈕 ( 圖 20) 電動煮水器會將水加熱到 80ºC 在除垢程序期間, 除垢指示燈會緩慢閃動, 直到除垢程序結束為止 顯示螢幕上會倒數除垢程序 (30 分鐘 ) 的時間 ( 以 5 分鐘為單位 ) 顯示螢幕上的時間會緩慢閃動 當除垢程序結束後, 您會聽見訊息音, 產品將自動關閉 4 請依照前述 清除電動煮水器的水垢 (HD9380/HD9384) 單元中的步驟 4 和 5 注意 : 如果在除垢程序結束之前, 即將電動貯水離拿離底座, 產品會自動關閉 您也可以按下任何一個預設按鈕以關閉除垢程序 注意 : 如果您沒有為電動煮水器除垢, 除垢指示燈會在隨後 5 次使用電動煮水器時亮起 收納 若要收納電線, 請將電源線捲入底座底部的電線收納裝置 ( 圖 2) 訂購配件如需購買本產品的配件, 請造訪我們的線上商店 : www.shop.philips.com/service 若您所在國家沒有線上商店, 請聯絡您的飛利浦經銷商或飛利浦服務中心 如果無法取得產品的配件, 請聯絡您所在國家的飛利浦客戶服務中心 如需詳細聯絡資料, 請參閱全球保證書 環境保護 本產品使用壽命結束時請勿與一般家庭廢棄物一併丟棄 請將該產品放置於政府指定的回收站, 此舉能為環保盡一份心力 ( 圖 21) 保固與服務若您需要相關服務或資訊, 或是有任何問題, 請瀏覽飛利浦網站 :www.philips.com/support, 或聯絡當地的飛利浦客戶服務中心, 您可以在全球保證書上找到聯絡電話 若您當地沒有客戶服務中心, 請洽詢當地的飛利浦經銷商 故障排除本章概述您使用本產品時最常遇到的問題 如果您無法利用以下資訊解決您遇到的問題, 請造訪 www.philips.com/support, 或聯絡您所在國家 / 地區的飛利浦客戶服務中心 訊號 保溫按鈕周圍的指示燈亮起, 其他指示燈關閉 我按下的預設按鈕指示燈閃爍了 3 次 顯示螢幕顯示 E5 錯誤訊息 電動煮水器發出嗶聲 問題 無法設定想要的溫度 我試著開啟電動煮水器, 但它卻自動關閉 保溫功能啟動時, 電動煮水器的電源會自動關閉 可能的解決方法 意義 / 解決方法 當水溫到達設定溫度後, 所選預設按鈕的燈會持續亮起 5 分鐘 水溫高於所選預設按鈕的溫度 電動煮水器壞了 請連絡經授權的飛利浦服務中心, 或者您國家中的客戶服務中心 水溫達到設定的溫度 目前壺內的水溫可能比您想設定的溫度高 您可以在壺中加入冷水 如果您想立即將水重新加熱, 您僅可選擇 100ºC 當電動煮水器中沒有水時, 將啟動防乾燒保護, 電動煮水器會自動關閉 您可能需要多加一些水進壺內 ( 至少 0.25 公升 ) 未正確將電動煮水器放置於底座上 將電動煮水器從底座移除, 然後再將其正確放置於底座上 電動煮水器保溫 30 分鐘後會自動關閉 如果要讓水溫長期保持熱度, 請在保溫結束後再按一次保溫按鈕