Procuct Installation CD KN04-00132A (Rev.1.1) Information This installation guide contains quick information required for the product installation. Please refer to the Software and Documents provided on the Download section of the BIXOLON Website(http://www.bixolon.com) for more information on how to setup. 1. Manual: User s Manual, Code Table, Control Commands, Software manuals 2. Driver: Windows, OPOS, CUPS(Linux, Mac), VCOM(USB, Ethernet) 3. SDK: UPOS SDK(iOS) 4. Utility: Unified POS Utility, Net Configuration Tool, Android Utility, ios Utility We at BIXOLON maintain ongoing efforts to enhance and upgrade the functions and quality of all our products. In following, product specifications and/or user manual content may be changed without prior notice. Components SRP-S300 Power cord CD Partition 2ea Installation Guide Cable Connection 1. Turn off the printer and peripheral devices. 2. Connect the power cord to the adapter and connect the adapter to the power supply connector of the printer. 3. Check the type of the interfaces at the back of the printer (USB, Serial, Parallel, Ethernet, Powered USB, Bluetooth, Wireless LAN) and connect the interface cable. 4. Connect the drawer kick-out cable to the drawer kick-out connector of the printer. Do not use an adapter that was not supplied with the printer. Power cord Installing Paper Roll Printer Installation Guide & Safety Guide Power Interface connector Drawer kick-out cable Interface cable Drawer kick-out connector (USB, Serial, Parallel, Ethernet, Powered USB, Bluetooth, Wireless LAN) 1. Press the Cover-Open button to open the cover. 2. Insert new roll paper in the correct direction. 3. Pull the paper out slightly and close the cover. 4. After the paper is rolled about 70mm, it switches to the black mark mode if there is a black mark, otherwise, it is automatically set to the continuous paper mode. Note When closing the cover, press down on the center of the cover to ensure that the paper is in contact with the roller. Printing quality may not be optimum if recommended paper is not used. (Refer to the User's Manual.) Using Control Panel POWER LED The POWER light is on whenever the printer is on. ERROR LED This indicates an error. PAPER LED This light indicates the near end of the paper roll. Install a new paper roll and the printer will continue printing. When the light blinks, it indicates the self-test printing standby state or macro execution Standby state when the macro execution command is used. FEED Button Press the FEED button once to advance paper one line. You can also hold down the FEED button to feed paper continuously. THERMAL SRP-S300 Mounting Partition(40, 58, 62mm) Using of 83mm Paper Roll DIP Switch Setting DIP switch settings should be changed when the printer power is turned off. Any changes made while printer power is on are not recognized. 1. DIP Switch 1 Serial Interface Setting Switch Function ON Default 1-1 Auto Line Feed Enabled Disabled 1-2 Flow Control XON/X DTR/DSR 1-3 Data Length 7 bits 8 bits 1-4 Parity Check Yes No 1-5 Parity Selection EVEN ODD 1-6 1-7 Baud Rate(bps) Refer to the following Table 1 ON 1-8 Parallel / USB / Ethernet / Wireless LAN / Powered USB Interface Setting Switch Function ON Default 1-1 Auto Line Feed Enabled Disabled 1-2~6 Reserved - - 1-7 Reserved - - ON 1-8 Reserved - - Bluetooth Interface Setting Switch Function ON Default 1-1 Auto Line Feed Enabled Disabled 1-2 Reserved - - 1-3 SSP Mode Enable Disable 1-4~6 Reserved - - 1-7 Reserved - - ON 1-8 Reserved - - Table 1 Baud Rate(bps) Selection Baud Rate 1-6 1-7 1-8 Default 2400 ON 4800 ON ON 9600 ON 19200 9600 38400 ON ON 57600 ON 115200 ON ON ON 2. DIP Switch 2 SRP-S300L/T Switch Function ON Default 2-1 Reserved - - 2-2 Black Mark Sensor Disable Enable 2-3 Internal Bell Control Disabled Enabled 2-4 Taken Sensor *1) Disable Enable 2-6 Printing Refer to the following Table 2 2-7 2-8 Auto External Buzz Enabled Disabled *1) Dip Switch 2-4 is only valid for Taken Sensing Model (SRP-S300T). And then both taken sensing and back feeding are disabled when 2-4 is on. SRP-S300R Switch Function ON Default 2-1 Reserved - - 2-2 Near End Sensor Control Disabled Enabled 2-3 Internal Bell Control Disabled Enabled 2-4 Reserved - - 2-6 Printing Refer to the following Table 2 2-7 2-8 Auto External Buzz Enabled Disabled Table 2 Printing Selection Printing 2-6 2-7 Default Level 1 Level 2 ON Level 3 ON - Level 1 is Default Level 4 ON ON - Level 6 is est Level 5 ON Level 6 ON ON Print The print density can be set to one of eighteen different levels through virtual memory switches.
Dip Switch Level 6(High ) 3 Level 1 5 6 Level 2 4 9 Level 3 3 12 Level 4 2 15 Level 5 1(Low ) 18 Level 6 Memory Switch Level 6(High ) 1 2 3 Level 1 5 4 5 6 Level 2 4 7 8 9 Level 3 3 10 11 12 Level 4 2 13 14 15 Level 5 1(Low ) 16 17 18 Level 6 * Choose Unified Utility or Self-Test mode to set the print density using the VMSM. (Virtual Memory Switch Management) * Change in DIP Switch settings are recognized only when the printer power is turned on or when the printer is reset by using the interface. If the DIP Switch setting is changed after the printer power is turned on, the change does not take effect until the printer is turned on again or is reset. Self-Test 1. Check whether the paper is inserted correctly. 2. Turn on the printer while depressing the Feed button. Self-diagnostics will begin. 3. The printer prints the current status of the printer such as the version of the ROM and DIP switch setting. 4. The printer prints the current status and stops after printing the following statement. (PAPER indicator keeps blinking.) SELF-TEST PRINTING. SELECT MODES BY PRESSING FEED BUTTON. Continuous SELF-TEST : Less than 1 second VMSM Selection : 1second or more 5. Press the FEED button for less than 1 second to perform Continuous SELF-TEST. Hold down the FEED button for 1 second or longer to perform VMSM Selection. 1) Self-Test 1-1) If you press the FEED button for less than 1 second, the printer will print in the preset character type. 1-2) The self-test completes automatically and cuts the paper after printing the following line. *** COMPLETED *** 1-3) The printer goes into standby mode when the self-test is complete. 2) Virtual Switch Setting Mode 2-1) When the printer goes into virtual switch-setting mode, the following lines will be printed. ** VMSM Selection ** 0: Exit and Reboot Printer 1: Print Current Settings 2: Set Print 3: Set Print 4: Set Cutting Mode 5: Beep-once Alarm 6: Continuous Alarm 7: Set Black Mark Cut Position *1) 8 or more: None *1) Sticky, Re-stick, Linerless Extreme Model only 2-2) Make sure to press the FEED button to perform the above functions. 2-2-1) Step 1: The number indicates the number of times the FEED button needs to be pressed. Make sure to press it for less than 1 second. 2-2-2) Step 2: Hold down the FEED button for 1 second or longer to enter the selected item. If there is no selected item in Step 1, select 0: Exit and reboot printer to exit. 2-3) When the new settings are applied, hold down the FEED button for 1 second or longer to save the changes. Cut the paper when the following line is printed. (If 0: Exit and reboot printer is not performed, the new settings will not be saved.) *** COMPLETED *** 6. The settings will take effect after the printer reboots. Note You can check whether the printer operates normally or not through self-diagnostics. You can check printing quality, ROM version, and DIP switch settings through self-diagnostics. Using of Taken Sensor Function When it comes to Taken Sensor, it will detect the paper not to feed next paper before user detach it. This function will be supported by SRP-S300T. WEEE(Waste Electrical and Electric Equipment) This marking shown on the product or its literature, indicates that is should not be disposed with other household wastes at the end of its working life, To prevent possible harm to the environment or human health from uncontrolled waste disposal, please separate this from other types of wastes and recycle it responsibly to promote the sustainable reuse of material resources. Household users should contact either the retailer where they purchased this product, or their local government office, for details of where and how they can take this item for environmentally safe recycling. Business users should contact their supplier and check the terms and conditions of the purchase contract. This product should not be mixed with other commercial wastes for disposal. BIXOLON Co., Ltd. Website http://www.bixolon.com Korea Headquarters (Add) 7~8F, (Sampyeong-dong), 20, Pangyoyeok-ro241beon-gil, Bundang-gu, Seongnam-si, Gyeonggi-do, 13494, Korea (ROK) (Tel.) +82-31-218-5500 U.S. Office (Add) BIXOLON America Inc., 3171 Fujita St, Torrance, CA 90505 (Tel.) +1-858 764 4580 Europe Office (Add) BIXOLON Europe GmbH, Tiefenbroicher Weg 35 40472 Düsseldorf (Tel.) +49 (0)211 68 78 54 0 Safety Precautions In using the present appliance, please keep the following safety regulations in order to prevent any hazard or material damage. WARNING Violating following instructions can cause serious injury or death. Do not plug several products in one multi-outlet. This can provoke over-heating and a fire. If the plug is wet or dirty, dry or wipe it before usage. If the plug does not fit perfectly with the outlet, do not plug in. Be sure to use only standardized multi-outlets. Do not pull the cable to unplug. This can damage the cable, which is the origin of a fire or a breakdown of the printer. Do not plug in or unplug with your hands wet. You can be electrocuted. CAUTION Violating following instructions can cause slight wound or damage the appliance. If you observe a strange smoke, odor or noise from the printer, unplug it before taking following measures. Switch off the printer and unplug the set from the mains. After the disappearance of the smoke, call your dealer to repair it. TO UNPLUG Install the printer on the stable surface. If the printer falls down, it can be broken and you can hurt yourself. Do not let water or other foreign objects in the printer. If this happened, switch off and unplug the printer before calling your dealer. You must use only the supplied adapter. It is dangerous to use other adapters. Keep the plastic bag out of children s reach. If not, a child may put the bag on his head. Do not bend the cable by force or leave it under any heavy object. A damaged cable can cause a fire. ONLY SUPPLIED ADAPTER Keep the desiccant out of children s reach. If not, they may eat it. Use only approved accessories and do not try to disassemble, repair or remodel it for yourself. Call your dealer when you need these services. Do not touch the blade of auto cutter. DISASSEMBLING Do not use the printer when it is out of order. This can cause a fire or an electrocution. Switch off and unplug the printer before calling your dealer. TO UNPLUG DEALER
Procuct Installation CD 안내본설치안내서는제품설치에필요한간단한정보만기록하고있습니다. 자세한설치안내는빅솔론홈페이지 (http://www.bixolon.com) 의다운로드페이지에서제공되는 Software 및 Document 를참고하십시오. 1. 매뉴얼 : 사용자매뉴얼, 코드표, 제어명령, 소프트웨어매뉴얼 2. 드라이버 (Driver): Windows, OPOS, JavaPOS, CUPS(Linux, Mac), 가상시리얼포트 (USB 및 Ethernet 용 ) 3. 소프트웨어개발도구 (SDK): UPOS SDK(iOS, Android) 4. 유틸리티 (Utility): 통합 POS 유틸리티 (Unified POS Utility), 네트워크설정도구 (Net Configuration Tool), 안드로이드유틸리티 (Android Utility), ios 유틸리티 (ios Utility) 저희 ( 주 ) 빅솔론은제품의기능과품질향상을위하여지속적인개선을하고있습니다. 이로인하여제품의사양과매뉴얼의내용은사전통보없이변경될수있습니다. 내용물확인 SRP-S300 전원코드 CD 파티션 2 개 설치안내서 케이블연결 1. 프린터와주변기기의전원을끕니다. 2. 전원코드를어댑터에연결하고, 어댑터를프린터의전원커넥터에연결하십시오. 3. 프린터뒷면에있는인터페이스종류 (USB, 시리얼, 패러럴, 이더넷, Powered USB, 블루투스, 무선랜 ) 를확인하시고, 인터페이스커넥터에케이블을연결합니다. 4. 프린터의드로어킥아웃커넥터에드로어킥아웃케이블을연결합니다. 어댑터는반드시공급된제품만을사용하십시오. 전원코드 인터페이스커넥터드로어킥아웃케이블드로어킥아웃커넥터인터페이스케이블 (USB, 시리얼, 패러럴, 이더넷, Powered USB, 블루투스, 무선랜 ) 롤용지설치 1. 커버열림레버를올려커버를엽니다. 2. 새로운롤용지를올바른방향으로삽입합니다. 3. 약간의용지를당긴다음, 커버를닫습니다. 4. 용지가약 70mm 이송후블랙마크가있을경우블랙마크모드로전환되며, 없을경우에는연속용지모드로자동설정됩니다. 참고커버를닫을때에는용지가롤러에밀착되도록커버의가운데를눌러주십시오. 권장용지를사용하지않을경우인쇄품질이저하될수있습니다. ( 사용자매뉴얼참고 ) 조작부사용 POWER( 전원 ) LED 전원표시등은프린터에전원이켜져있을경우켜집니다. ERROR( 오류 ) LED 오류가발생하였을때켜집니다. PAPER( 종이 ) LED 이표시등이켜지면용지가거의다소모되었거나용지가없음을나타냅니다. 새용지로교환하거나용지를넣으십시오. 이표시등이깜빡거리면 SELF TEST 대기상태이거나매크로실행대기중임을나타냅니다. FEED( 이송 ) 버튼용지한라인을배출하기위해서는이송버튼을한번누르십시오. 이송버튼을계속누르고있으면용지를연속적으로배출할수있습니다. 프린터설치안내서 & 안전가이드감열식프린터 SRP-S300 전원 파티션장착 (40, 58, 62mm) 세부사용방법에대한설명은유저매뉴얼을참조하십시요 83mm 롤용지사용세부사용방법에대한설명은유저매뉴얼을참조하십시요 DIP 스위치설정 DIP 스위치설정변경은프린터전원을끈상태에서해야합니다. 켠상태에서의변경은인식되지않습니다. 1. DIP 스위치 1 시리얼 (Serial) 인터페이스설정 스위치 기능 ON 기본값 1-1 자동라인피딩 동작 해제 1-2 흐름제어 XON/X DTR/DSR 1-3 데이터길이 7비트 8비트 1-4 패리티체크여부 체크함 체크안함 1-5 패리티 EVEN ODD 1-6 1-7 전송속도 (bps) 아래표 1 참조 ON 1-8 패러럴 (Parallel) / USB / 이더넷 (Ethernet) / 무선랜 (Wireless LAN) / Powered USB 인터페이스설정 스위치 기능 ON 기본값 1-1 자동라인피딩 동작 해제 1-2~6 없음 - - 1-7 없음 - - ON 1-8 없음 - - 블루투스 (Bluetooth) 인터페이스설정 스위치 기능 ON 기본값 1-1 자동라인피딩 동작 해제 1-2 없음 - - 1-3 SSP Mode 동작 해제 1-4~6 없음 - - 1-7 없음 - - ON 1-8 없음 - - 표 1 전송속도 (bps) 선택전송속도 1-6 1-7 1-8 기본값 2400 ON 4800 ON ON 9600 ON 19200 9600 38400 ON ON 57600 ON 115200 ON ON ON 2. DIP 스위치 2 SRP-S300L/T 스위치 기능 ON 기본값 2-1 없음 - - 2-2 블랙마크센서 해제 동작 2-3 내부벨제어 내부벨해제 내부벨동작 2-4 Taken 센서 *1) 해제 동작 2-6 인쇄농도 아래표 2 참조 2-7 2-8 외부부저제어 외부부저동작 외부부저해제 *1) DIP 스위치 2-4 설정기능은 Taken 센서모델 (SRP-S300T/TX) 전용기능입니다. 만약, Taken 센서기능을사용하지않을경우에는 DIP 스위치 2-4 를 ON 하면기능이 해제되고동시에 Back Feeding 기능도자동으로해제됩니다. SRP-S300R 스위치 기능 ON 기본값 2-1 없음 - - 2-2 용지부족감지 기능해제 정상동작 2-3 내부벨제어 내부벨해제 내부벨동작 2-4 없음 - - 2-6 인쇄농도 아래표 2 참조 2-7 2-8 외부부저제어 외부부저동작 외부부저해제 표 2 인쇄농도선택 인쇄농도 2-6 2-7 기본값 Level 1 Level 2 ON Level 3 ON Level 4 ON ON Level 5 ON Level 6 ON ON - Level 1 is Default - Level 6 is est
인쇄농도 인쇄농도는가상메모리스위치를통해총 18 단계로세분화하여사용할수있습니다. Dip 스위치 농도 인쇄농도 6( 고속 ) 3 Level 1 5 6 Level 2 4 9 Level 3 3 12 Level 4 2 15 Level 5 1( 저속 ) 18 Level 6 메모리스위치 농도 인쇄농도 6( 고속 ) 1 2 3 Level 1 5 4 5 6 Level 2 4 7 8 9 Level 3 3 10 11 12 Level 4 2 13 14 15 Level 5 1( 저속 ) 16 17 18 Level 6 안전상의경고 제품을올바르게사용하여위험이나물적손해를미리방지하기위한내용이므로반드시지켜사용해주세요. 경고표시사항위반시심각한상해나사망이발생할가능성이있습니다. 한콘센트에여러제품의전원플러그를동시에꽂지마세요. 발열및발화되어위험합니다. 전원플러그에서이물질이나물기가묻어있으면잘닦아사용하세요. 전원콘센트의구멍이헐거울때는전원플러그를꽂지마세요. 멀티콘센트는규격제품을사용하세요. 어댑터는공급된제품만을사용하세요. 다른어댑터를사용하면위험합니다. 반드시공급품만 * 가상메모리스위치로인쇄농도를변경하기위해서는 Unified Utility 또는 Self- Test 모드를사용하시길바랍니다. * DIP 스위치설정변경은프린터전원을끈상태에서해야합니다. 켠상태에서의변경은인식되지않습니다 전원플러그를뺄때는전원코드를잡아당기지마세요. 코드가상처를입어화재나고장의원인이됩니다. 비닐팩은어린이의손에닿지않는곳에잘보관하세요. 어린이가비닐팩을머리에쓰면위험합니다. 1. 용지가정상적으로설치되어있는지확인하십시오. 2. 이송버튼을누른상태에서전원을켜십시오. 자가진단이시작됩니다. 3. 프린터는 ROM 의버전과 DIP 스위치설정상태와같은프린터의현재상태를인쇄합니다. 4. 프린터의현재상태를인쇄하고난후, 다음과같은문구를인쇄한후멈춥니다. ( 종이표시등은계속깜빡입니다 ). SELF-TEST PRINTING. 다음을실행하려면버튼으로선택하시오. 테스트인쇄계속수행 : 버튼을짧게누름메모리스위치설정모드 : 버튼을길게누름 5. 테스트인쇄계속수행 을진행하기위해서는이송버튼을 1 초이하로누르시고, 메모리스위치설정모드 를진행하기위해서는이송버튼을 1 초이상누르십시오. 1) 자가진단 1-1) 이송버튼을 1 초이하로누르면프린터는미리제작된문자형식을인쇄합니다. 1-2) 자가진단은자동으로끝나고다음과같은문구를인쇄한후용지를절단합니다. *** 설정완료 *** 1-3) 프린터는자가진단이끝나면바로정상상태가됩니다. 2) 가상메모리스위치설정모드 2-1) 가상메모리스위치관리 (VMSM) 에진입하면다음과같은문구를인쇄합니다. ** 가상메모리스위치관리 (VMSM) ** 0: 설정저장및종료 1: 현재메모리스위치정보인쇄 2: 인쇄농도설정 3: 인쇄속도설정 4: 용지절단모드설정 5: 1 회알람 6: 연속알람 7: 용지절단위치설정 *1) 8 or more: None *1) 스티키, 리스틱, 라이너리스익스트림모델전용기능 2-2) 위의기능을실행하기위해서는아래와같이이송버튼을동작시켜주십시오. 2-2-1) 단계 1: 위의항목앞의숫자는이송버튼을누르는횟수를의미합니다. 원하는항목의숫자횟수만큼이송버튼을 1 초이하로짧게누르십시오. 2-2-2) 단계 2: 1 초이상버튼을길게누르면선택한항목으로진입합니다. 단계 1 에서선택한항목이없으면 0: 설정저장및종료 를선택하고취소합니다. 2-3) 기능변경이완료되면변경된기능을저장하기위해이송버튼을 1 초이상길게눌러주십시오. 다음과같은문구를인쇄한후용지를절단합니다. ( 0: 설정저장및종료 기능이실행되지않으면설정정보는프린터에저장되지않습니다.) *** 설정완료 *** 6. 프린터가재부팅하며변경된설정정보가반영됩니다. 참고자가진단을통해프린터가제대로작동되고있는지확인할수있습니다. 자가진단으로인쇄품질, ROM 버전, DIP 설정을확인합니다. Taken Sensor 기능사용 Taken Sensor 기능은인쇄물을회수해가지않으면다음장인쇄가되지않게하는기능으로전용모델명은 SRP-S300T 입니다. 세부사용방법에대한설명은유저매뉴얼을참조하십시오. BIXOLON Co., Ltd. 웹사이트 http://www.bixolon.com 한국본사 ( 주소 ) 13494, 경기도성남시분당구판교역로 241 번길 20 ( 삼평동 ) 7~8 층 ( 전화 ) +82-31-218-5500 미주지사 ( 주소 ) BIXOLON America Inc., 3171 Fujita St, Torrance, CA 90505 ( 전화 ) +1-858 764 4580 유럽지사 ( 주소 ) BIXOLON Europe GmbH, Tiefenbroicher Weg 35 40472 Düsseldorf ( 전화 ) +49 (0)211 68 78 54 0 젖은손으로전원플러그를꽂거나뽑지마세요. 감전의위험이있습니다. 주의표시사항위반시경미한상해나제품손상이발생할가능성이있습니다. 제품에서연기가나거나이상한냄새또는소리가나는등의이상발생시는바로전원을끈후아래의조치를취해주세요. 제품에이상이발생시는바로프린터본체의전원을끈다음반드시전원플러그를콘센트에서뽑아주세요. 연기가나지않는것을확인하고구입처로수리를의뢰해주세요. 플러그 안정된장소에설치하세요. 넘어지면제품이파손되거나다칠수있습니다. 프린터의본체내부에물이나이물질이들어가지않도록주의하세요. 본체내부에물이나이물질이들어간경우에는먼저프린터본체의전원스위치를끄고전원플러그를콘센트에서뺀다음구입처로연락해주세요. 프린터 프린터 프린터 전원코드를무리하게구부리거나무거운물건을눌러파손되지않도록하세요. 화재의원인이됩니다. 방습제는어린이의손에닿지않는곳에잘보관하세요. 어린이가방습제를먹으면위험합니다. 승인된부품을사용하고함부로분해, 수리, 개조하지마세요. 제품이손상될수있으므로구입처에문의하세요. 자동절단기날은날카로우므로손대지마십시오. 분해 제품을고장난상태에서사용하지마세요. 화재, 감전의원인이됩니다. 바로본체의전원스위치를끄고전원플러그를콘센트에서뺀다음구입처로연락해주세요. 플러그 프린터 프린터구입처
Procuct Installation CD 指南本安装手册仅收录有安装产品所需的简单信息 详情请参考毕索龙网站 (http://www.bixolon.com) 下载页面中提供的 Software 和 Document 1. 手册 : 使用说明书 代码表 控制命令 软件手册 2. 驱动器 (Driver):Windows OPOS JavaPOS CUPS(Linux Mac) 虚拟串口 (U 盘及以太网用 ) 3. 软件开发工具 (SDK):UPOS SDK(iOS Android) 4. 实用程序 (Utility): 整合 POS 实用程序 (Unified POS Utility) 网络设置工具 (Net Configuration Tool) 安卓实用程序 (Android Utility) ios 实用程序 (ios Utility) 毕索龙人始终坚持不懈, 努力提高和改进所有产品的功能和质量 因此产品规格和用户手册的内容可能会有所变动, 恕不另行通知 确认内容物 SRP-S300 电源线 光盘 2 个分区板 安装指南书 连接电缆 1. 关闭打印机和周边设备的电源 2. 请将电源线连接至适配器, 再将适配器连接至打印机的电源连接器 3. 确认打印机后面的接口类型 (U 盘 串联 并联 以太网 Powered U 盘 蓝牙 无线 ), 然后在接口连接器上接入电缆 4. 在打印机的现金抽屉连接器上接入现金抽屉电缆 只能使用原厂提供的连接器 电源插头 接口连接器现金抽屉电缆现金抽屉连接器接口电缆 (U 盘 串联 并联 以太网 Powered U 盘 蓝牙 无线网 ) 安装纸卷 1. 提起开启盖罩拉杆打开盖罩 2. 沿正确的方向插入新纸卷 3. 将纸张略微拉出一些后关闭盖罩 4. 送纸约 70mm 后出现黑标时, 转换为黑标模式 ; 没有黑标时, 自动设定为连续送纸模式 参考关闭盖罩时请按下盖罩的中间部位, 使纸卷辊筒确实被卡住 未使用建议用纸, 可能导致打印质量不佳 ( 参考用户手册 ) 操作部分的使用 POWER( 电源 )LED 电源指示灯在开启打印机电源时亮起 ERROR( 错误 )LED 出错时亮起 PAPER( 纸张 )LED 此显示灯亮起时表示纸张即将耗尽或缺纸 请更换新纸或装纸 此显示灯闪烁时表示处于等待 SELF TEST 状态或者正在等待执行宏 FEED( 送纸 ) 键按一次送纸键即可送出一行纸 按住送纸键可以连续送纸 电源 打印机安装指南书 & 安全指南热敏式打印机 SRP-S300 安装分区板 (40 58 62mm) 具体使用方法的有关说明请参考用户手册 使用 83mm 的纸卷具体使用方法的有关说明请参考用户手册 设置 DIP 开关 应在关闭打印机电源的状态下变更 DIP 开关的设置 不识别在开启状态下的变更 1. DIP 开关 1 设置串联 (Serial) 接口 开关 功能 ON 基本值 1-1 自动换行 运行 解除 1-2 流动控制 XON/X DTR/DSR 1-3 数据长度 7 字节 8 字节 1-4 是否核对奇偶 核对 不核对 1-5 奇偶 EVEN ODD 1-6 1-7 传送速度 (bps) 参考下表 1 ON 1-8 设置并联 (Parallel)/U 盘 / 以太网 (Ethernet)/ 无线网 (Wireless LAN)/Powered U 盘接口 开关 功能 ON 基本值 1-1 自动换行 运行 解除 1-2~6 无 - - 1-7 无 - - ON 1-8 无 - - 设置蓝牙 (Bluetooth) 接口 开关 功能 ON 基本值 1-1 自动换行 运行 解除 1-2 无 - - 1-3 SSP Mode 运行 解除 1-4~6 无 - - 1-7 无 - - ON 1-8 无 - - 表 1 选择传送速度 (bps) 传送速度 1-6 1-7 1-8 基本值 2400 ON 4800 ON ON 9600 ON 19200 9600 38400 ON ON 57600 ON 115200 ON ON ON 2. DIP 开关 2 SRP-S300L/T 开关 功能 ON 基本值 2-1 无 - - 2-2 黑标传感器 解除 运行 2-3 内部铃控制 内部铃解除 内部铃运行 2-4 *1) Taken 传感器 解除 运行 2-6 打印浓度 参考下表 2 2-7 2-8 外部蜂鸣器控制 外部蜂鸣器运行 外部蜂鸣器解除 *1) DIP 开关 2-4 设置是一种 Taken 传感器型号 (SRP-S300T/TX) 的专用功能 如不需 使用 Taken 传感器功能, 开启 DIP 开关 2-4, 即可解除该功能,Back Feeding 功能也随之 自动解除 SRP-S300R 开关 功能 ON 基本值 2-1 无 - - 2-2 感测纸张不足 解除功能 正常运行 2-3 内部铃控制 内部铃解除 内部铃运行 2-4 无 - - 2-6 打印浓度 参考下表 2 2-7 2-8 外部蜂鸣器控制 外部蜂鸣器运行 外部蜂鸣器解除 表 2 选择打印浓度 打印浓度 2-6 2-7 基本值 Level 1 Level 2 ON Level 3 ON Level 4 ON ON Level 5 ON Level 6 ON ON - Level 1 is Default - Level 6 is est
打印浓度 通过虚拟内存开关细分为 18 级打印浓度使用 Dip 开关 浓度 打印浓度 6( 高速 ) 3 Level 1 5 6 Level 2 4 9 Level 3 3 12 Level 4 2 15 Level 5 1( 低速 ) 18 Level 6 内存开关 浓度 打印浓度 6( 高速 ) 1 2 3 Level 1 5 4 5 6 Level 2 4 7 8 9 Level 3 3 10 11 12 Level 4 2 13 14 15 Level 5 1( 低速 ) 16 17 18 Level 6 * 如需用虚拟内存开关变更打印浓度, 请使用 Unified Utility 或 Self-Test 模式 * 应在关闭状态下变更 DIP 开关设置 不识别在开启状态下的变更 1. 请确认是否正常装纸 2. 请在按下送纸键的状态下开启电源, 开始自检 3. 打印机打印 ROM 的版本与 DIP 开关设定状态相同的打印机当前状态 4. 打印机打印当前状态后, 打印如下语句并停止打印 ( 纸张指示灯持续闪烁 ) SELF-TEST PRINTING. SELECT MODES BY PRESSING FEED BUTTON. ( 如要执行下一个, 请用按钮选择 ) Continuous SELF-TEST :Less than 1 second ( 持续执行测试打印 : 短暂按下按钮 ) VMSM Selection :1second or more ( 内存开关设置模式 : 较长按住按钮 ) 5. 如要进行 Continuous SELF-TEST, 请按下送纸按钮 1 秒 ; 如要进行 VMSM Selection, 请按住送纸按钮 1 秒以上 1) 自检 1-1) 按下送纸按钮 1 秒以下, 按照打印机预先编制的字符形式打印 1-2) 自动结束自检并打印如下语句后切断纸张 *** COMPLETED *** (*** 设置完毕 ***) 1-3) 打印机在自检完毕后立即返回正常状态 2) 虚拟内存开关设置模式 2-1) 进入虚拟内存开关管理 (VMSM) 后打印如下语句 ** VMSM Selection ** (** 虚拟内存开关管理 **) 0:Exit and Reboot Printer ( 保存设置及结束 ) 1:Print Current Settings ( 打印当前内存开关信息 ) 2:Set Print ( 设置打印浓度 ) 3:Set Print ( 设置打印速度 ) 4:Set Cutting Mode ( 设置切割纸张模式 ) 5:Beep-once Alarm ( 提醒一次 ) 6:Continuous Alarm ( 连续提醒 ) 7:Set Black Mark Cut Position ( 设置切割纸张位置 ) *1) 8 or more:none ( 或更多 : 无 ) *1) Sticky Ristic Linerless Extreme 型号产品的专用功能 2-2) 请按照如下内容运行送纸按钮, 以执行上述功能 2-2-1) 第一步 : 上述项目前面的数字指按下送纸按钮的次数 请根据所需项目的数字, 按照相应次数短暂按下按钮 1 秒以下 2-2-2) 第二步 : 按住按钮 1 秒以上, 进入所选的项目 没有第一步所选的项目时选择 0:Exit and reboot printer 后取消 2-3) 功能变更完毕后请按住送纸按钮 1 秒以上, 保存变更后的功能 打印如下语句后切断纸张 ( 不执行 0:Exit and reboot printer 功能, 打印机将无法保存设置信息 ) *** COMPLETED *** (*** 设置完毕 ***) 6. 重启打印机, 适用变更后的设置信息 参考可以通过自检确认打印机是否正常运行可以通过自检确认打印质量 ROM 版本 DIP 设定 安全注意警告 如下是正确使用打印机, 预防危险和财物损失的有关内容, 请务必遵守 警告违反以下事项可能会导致严重的伤亡事故 请勿将几个插头同时插入一个多孔电源插座中 连接多个插头会导致过热和火灾 如果插头潮湿或者肮脏, 请在使用前烘干或者擦拭干净 电源插座规格不符时, 请不要插上电源 只能使用标准化的多孔电源插座 不要通过拉掉连接线的方式拔插头 可能损坏连接线, 造成火灾或者打印机故障 请勿用湿手插拔电源插头 这可能导致触电 注意违反以下事项可能造成轻伤或损坏设备 如果发现打印机不明原因地冒烟 发出异味或者噪音, 请立即关闭电源, 采取下列急救措施 产品发生异常时, 请立即关闭打印机主机电源, 从插座上拔下设备的插头 请在烟消失后, 电话联系经销商进行维修 拔下插头 将打印机安装在稳固之处 打印机坠落, 可能导致机器损坏或人员受伤 打印机 打印机 只能使用原厂包装中提供的适配器 使用其它适配器十分危险 请将塑料袋放在儿童触及不到之处妥善保管 否则儿童会将袋子套在头上发生危险 不要用力弯曲连接线, 或者将其置于重物之下 可能导致火灾 必须只用提供品 请将干燥剂放在儿童触及不到之处妥善保管 否则会有吞食危险 请只使用经批准的零部件, 请勿擅自拆卸 修理或者改装 可能损坏产品, 请电话联系经销商 请勿触摸自动切纸器的锋利刀片 拆卸 打印机 使用 Taken Sensor 功能 Taken Sensor 是 SRP-S300T 型号产品的专用功能, 不收起已打印的纸张就不打印下一张 具体使用方法的有关说明请参考用户手册 BIXOLON Co., Ltd. 网址 http://www.bixolon.com 韩国总部 ( 地址 ) 京畿道城南市盆塘区板桥站路 241 街 20( 三坪洞 )7-8 楼邮编 13494 ( 电话 ) +82-31-218-5500 美洲分公司 ( 地址 ) BIXOLON America Inc., 3171 Fujita St, Torrance, CA 90505 ( 电话 ) +1-858 764 4580 欧洲分公司 ( 地址 ) BIXOLON Europe GmbH, Tiefenbroicher Weg 35 40472 Düsseldorf ( 电话 ) +49 (0)211 68 78 54 0 不要将水或者其他物品倒入打印机 如果发生此类事件, 请关机并拔下打印机的插头, 电话联系经销商 打印机 操作失灵时请勿使用打印机, 可能会导致火灾或者触电 请关机并拔下打印机的插头, 电话联系经销商 拔下插头 打印机经销处
Procuct Installation CD Information This installation guide contains quick information required for the product installation. Please refer to the Software and Documents provided on the Download section of the BIXOLON Website(http://www.bixolon.com) for more information on how to setup. 1. Manual: User s Manual, Code Table, Control Commands, Software manuals 2. Driver: Windows, OPOS, CUPS(Linux, Mac), VCOM(USB, Ethernet) 3. SDK: UPOS SDK(iOS) 4. Utility: Unified POS Utility, Net Configuration Tool, Android Utility, ios Utility We at BIXOLON maintain ongoing efforts to enhance and upgrade the functions and quality of all our products. In following, product specifications and/or user manual content may be changed without prior notice. Components SRP-S300 Power cord CD Partition 2ea Installation Guide Cable Connection 1. Turn off the printer and peripheral devices. 2. Connect the power cord to the adapter and connect the adapter to the power supply connector of the printer. 3. Check the type of the interfaces at the back of the printer (USB, Serial, Parallel, Ethernet, Powered USB, Bluetooth, Wireless LAN) and connect the interface cable. 4. Connect the drawer kick-out cable to the drawer kick-out connector of the printer. Do not use an adapter that was not supplied with the printer. Power cord Installing Paper Roll Printer Installation Guide & Safety Guide THERMAL SRP-S300 Power Interface connector Drawer kick-out cable Interface cable Drawer kick-out connector (USB, Serial, Parallel, Ethernet, Powered USB, Bluetooth, Wireless LAN) 1. Press the Cover-Open button to open the cover. 2. Insert new roll paper in the correct direction. 3. Pull the paper out slightly and close the cover. 4. After the paper is rolled about 70mm, it switches to the black mark mode if there is a black mark, otherwise, it is automatically set to the continuous paper mode. Note When closing the cover, press down on the center of the cover to ensure that the paper is in contact with the roller. Printing quality may not be optimum if recommended paper is not used. (Refer to the User's Manual.) Using Control Panel POWER LED The POWER light is on whenever the printer is on. ERROR LED This indicates an error. PAPER LED This light indicates the near end of the paper roll. Install a new paper roll and the printer will continue printing. When the light blinks, it indicates the self-test printing standby state or macro execution Standby state when the macro execution command is used. FEED Button Press the FEED button once to advance paper one line. You can also hold down the FEED button to feed paper continuously. Mounting Partition(40, 58, 62mm) Using of 83mm Paper Roll DIP Switch Setting DIP switch settings should be changed when the printer power is turned off. Any changes made while printer power is on are not recognized. 1. DIP Switch 1 Serial Interface Setting Switch Function ON Default 1-1 Auto Line Feed Enabled Disabled 1-2 Flow Control XON/X DTR/DSR 1-3 Data Length 7 bits 8 bits 1-4 Parity Check Yes No 1-5 Parity Selection EVEN ODD 1-6 1-7 Baud Rate(bps) Refer to the following Table 1 ON 1-8 Parallel / USB / Ethernet / Wireless LAN / Powered USB Interface Setting Switch Function ON Default 1-1 Auto Line Feed Enabled Disabled 1-2~6 Reserved - - 1-7 Reserved - - ON 1-8 Reserved - - Bluetooth Interface Setting Switch Function ON Default 1-1 Auto Line Feed Enabled Disabled 1-2 Reserved - - 1-3 SSP Mode Enable Disable 1-4~6 Reserved - - 1-7 Reserved - - ON 1-8 Reserved - - Table 1 Baud Rate(bps) Selection Baud Rate 1-6 1-7 1-8 Default 2400 ON 4800 ON ON 9600 ON 19200 9600 38400 ON ON 57600 ON 115200 ON ON ON 2. DIP Switch 2 SRP-S300L/T Switch Function ON Default 2-1 Reserved - - 2-2 Black Mark Sensor Disable Enable 2-3 Internal Bell Control Disabled Enabled 2-4 Taken Sensor *1) Disable Enable 2-6 Printing Refer to the following Table 2 2-7 2-8 Auto External Buzz Enabled Disabled *1) Dip Switch 2-4 is only valid for Taken Sensing Model (SRP-S300T). And then both taken sensing and back feeding are disabled when 2-4 is on. SRP-S300R Switch Function ON Default 2-1 Reserved - - 2-2 Near End Sensor Control Disabled Enabled 2-3 Internal Bell Control Disabled Enabled 2-4 Reserved - - 2-6 Printing Refer to the following Table 2 2-7 2-8 Auto External Buzz Enabled Disabled Table 2 Printing Selection Printing 2-6 2-7 Default Level 1 Level 2 ON Level 3 ON - Level 1 is Default Level 4 ON ON - Level 6 is est Level 5 ON Level 6 ON ON Print The print density can be set to one of eighteen different levels through virtual memory switches.
Dip Switch Level 6(High ) 3 Level 1 5 6 Level 2 4 9 Level 3 3 12 Level 4 2 15 Level 5 1(Low ) 18 Level 6 Memory Switch Level 6(High ) 1 2 3 Level 1 5 4 5 6 Level 2 4 7 8 9 Level 3 3 10 11 12 Level 4 2 13 14 15 Level 5 1(Low ) 16 17 18 Level 6 * Choose Unified Utility or Self-Test mode to set the print density using the VMSM. (Virtual Memory Switch Management) * Change in DIP Switch settings are recognized only when the printer power is turned on or when the printer is reset by using the interface. If the DIP Switch setting is changed after the printer power is turned on, the change does not take effect until the printer is turned on again or is reset. Self-Test 1. Check whether the paper is inserted correctly. 2. Turn on the printer while depressing the Feed button. Self-diagnostics will begin. 3. The printer prints the current status of the printer such as the version of the ROM and DIP switch setting. 4. The printer prints the current status and stops after printing the following statement. (PAPER indicator keeps blinking.) SELF-TEST PRINTING. SELECT MODES BY PRESSING FEED BUTTON. Continuous SELF-TEST : Less than 1 second VMSM Selection : 1second or more 5. Press the FEED button for less than 1 second to perform Continuous SELF-TEST. Hold down the FEED button for 1 second or longer to perform VMSM Selection. 1) Self-Test 1-1) If you press the FEED button for less than 1 second, the printer will print in the preset character type. 1-2) The self-test completes automatically and cuts the paper after printing the following line. *** COMPLETED *** 1-3) The printer goes into standby mode when the self-test is complete. 2) Virtual Switch Setting Mode 2-1) When the printer goes into virtual switch-setting mode, the following lines will be printed. ** VMSM Selection ** 0: Exit and Reboot Printer 1: Print Current Settings 2: Set Print 3: Set Print 4: Set Cutting Mode 5: Beep-once Alarm 6: Continuous Alarm 7: Set Black Mark Cut Position *1) 8 or more: None *1) Sticky, Re-stick, Linerless Extreme Model only 2-2) Make sure to press the FEED button to perform the above functions. 2-2-1) Step 1: The number indicates the number of times the FEED button needs to be pressed. Make sure to press it for less than 1 second. 2-2-2) Step 2: Hold down the FEED button for 1 second or longer to enter the selected item. If there is no selected item in Step 1, select 0: Exit and reboot printer to exit. 2-3) When the new settings are applied, hold down the FEED button for 1 second or longer to save the changes. Cut the paper when the following line is printed. (If 0: Exit and reboot printer is not performed, the new settings will not be saved.) *** COMPLETED *** 6. The settings will take effect after the printer reboots. Note You can check whether the printer operates normally or not through self-diagnostics. You can check printing quality, ROM version, and DIP switch settings through self-diagnostics. Using of Taken Sensor Function When it comes to Taken Sensor, it will detect the paper not to feed next paper before user detach it. This function will be supported by SRP-S300T. WEEE(Waste Electrical and Electric Equipment) This marking shown on the product or its literature, indicates that is should not be disposed with other household wastes at the end of its working life, To prevent possible harm to the environment or human health from uncontrolled waste disposal, please separate this from other types of wastes and recycle it responsibly to promote the sustainable reuse of material resources. Household users should contact either the retailer where they purchased this product, or their local government office, for details of where and how they can take this item for environmentally safe recycling. Business users should contact their supplier and check the terms and conditions of the purchase contract. This product should not be mixed with other commercial wastes for disposal. BIXOLON Co., Ltd. Website http://www.bixolon.com Korea Headquarters (Add) 7~8F, (Sampyeong-dong), 20, Pangyoyeok-ro241beon-gil, Bundang-gu, Seongnam-si, Gyeonggi-do, 13494, Korea (ROK) (Tel.) +82-31-218-5500 U.S. Office (Add) BIXOLON America Inc., 3171 Fujita St, Torrance, CA 90505 (Tel.) +1-858 764 4580 Europe Office (Add) BIXOLON Europe GmbH, Tiefenbroicher Weg 35 40472 Düsseldorf (Tel.) +49 (0)211 68 78 54 0 Safety Precautions In using the present appliance, please keep the following safety regulations in order to prevent any hazard or material damage. WARNING Violating following instructions can cause serious injury or death. Do not plug several products in one multi-outlet. This can provoke over-heating and a fire. If the plug is wet or dirty, dry or wipe it before usage. If the plug does not fit perfectly with the outlet, do not plug in. Be sure to use only standardized multi-outlets. Do not pull the cable to unplug. This can damage the cable, which is the origin of a fire or a breakdown of the printer. Do not plug in or unplug with your hands wet. You can be electrocuted. CAUTION Violating following instructions can cause slight wound or damage the appliance. If you observe a strange smoke, odor or noise from the printer, unplug it before taking following measures. Switch off the printer and unplug the set from the mains. After the disappearance of the smoke, call your dealer to repair it. TO UNPLUG Install the printer on the stable surface. If the printer falls down, it can be broken and you can hurt yourself. Do not let water or other foreign objects in the printer. If this happened, switch off and unplug the printer before calling your dealer. You must use only the supplied adapter. It is dangerous to use other adapters. Keep the plastic bag out of children s reach. If not, a child may put the bag on his head. Do not bend the cable by force or leave it under any heavy object. A damaged cable can cause a fire. ONLY SUPPLIED ADAPTER Keep the desiccant out of children s reach. If not, they may eat it. Use only approved accessories and do not try to disassemble, repair or remodel it for yourself. Call your dealer when you need these services. Do not touch the blade of auto cutter. DISASSEMBLING Do not use the printer when it is out of order. This can cause a fire or an electrocution. Switch off and unplug the printer before calling your dealer. TO UNPLUG DEALER