(SW3704) Gingerbread Source Build & Working Guide

Size: px

Start display at page:

Download "(SW3704) Gingerbread Source Build & Working Guide"

은지 엽
6 years ago
Views:

1 (Mango-M32F4) Test Guide Crazy Embedded Laboratory cafe.naver.com/embeddedcrazyboys CRZ Technology 1

2 Document History Revision Date Change note Initital 오영환 2

3 목차 1. Booting Hardware Connection Debug Serial Port Key Test LED Test SDMMC Test SRAM Test USB Host Test Ethernet HTTP Test USB Device Test RTC Calendar Test CAN Test UART6 Test RS232 Test RS485 Test cafe.naver.com/embeddedcrazyboys CRZ Technology 3

4 1. Booting 1.1. Hardware Connection 1.2. Debug Serial Port 디버그시리얼포트의설정은아래와같습니다. Bud Rate Data Bits 8 Parity None Stop Bits 1 Flow Control None 2. Key Test 아래와같이출력됩니다. [CRZ] Work_Event_Process (60): USER Key 1 pressed [CRZ] Work_Event_Process (64): USER Key 1 released [CRZ] Work_Event_Process (68): USER Key 2 pressed [CRZ] Work_Event_Process (72): USER Key 2 released 3. LED Test 1> LED Test 4. SDMMC Test T-Flash 를장착합니다. 2> SDMMC Test 2 번을선택합니다. 4

5 [CRZ] main (148): 2 is selected [CRZ] SDMMC_Test (82): [CRZ] SDMMC_Initialization (30): [CRZ] SDMMC_Initialization (38): FATFS_LinkDriver OK [CRZ] f_mount (2486): [CRZ] f_mount (2492): vol: 0 [CRZ] SDMMC_Initialization (46): f_mount OK [CRZ] SDMMC_Test (106): BSP_SD_Init OK [CRZ] SDMMC_Format (70): SDMMC Card Format OK [CRZ] SDMMC_Test (113): Format OK [CRZ] f_open (2539): [CRZ] SDMMC_Test (122): f_open STM32.TXT OK [CRZ] SDMMC_Test (133): f_close STM32.TXT OK [CRZ] SDMMC_Test (142): STM32.TXT file Write OK [CRZ] f_open (2539): [CRZ] SDMMC_Test (151): f_open STM32.TXT OK [CRZ] SDMMC_Test (162): f_read STM32.TXT OK [CRZ] Wait_N_Seconds (41): Wait (1/1) second [CRZ] SDMMC_Test (178): Success demo OK [CRZ] Wait_N_Seconds (41): Wait (1/1) second [CRZ] SDMMC_Test (178): Success demo OK [CRZ] Wait_N_Seconds (41): Wait (1/1) second [CRZ] SDMMC_Test (178): Success demo OK [CRZ] Wait_N_Seconds (41): Wait (1/1) second [CRZ] SDMMC_Test (178): Success demo OK [CRZ] Wait_N_Seconds (41): Wait (1/1) second [CRZ] SDMMC_Test (178): Success demo OK [CRZ] Wait_N_Seconds (41): Wait (1/1) second [CRZ] SDMMC_Test (178): Success demo OK Success demo OK 가계속출력이됩니다. 5. SRAM Test 3> SRAM Test cafe.naver.com/embeddedcrazyboys CRZ Technology 5

6 3 번을선택합니다. [CRZ] main (148): 3 is selected [CRZ] SRAM_Test (113): [CRZ] Buffercmp (102): Count: 1, Data is same. [CRZ] Buffercmp (102): Count: 2, Data is same. [CRZ] Buffercmp (102): Count: 3, Data is same. [CRZ] Buffercmp (102): Count: 4, Data is same. [CRZ] Buffercmp (102): Count: 5, Data is same [CRZ] Buffercmp (102): Count: 250, Data is same. [CRZ] Buffercmp (102): Count: 251, Data is same. [CRZ] Buffercmp (102): Count: 252, Data is same. [CRZ] Buffercmp (102): Count: 253, Data is same. [CRZ] Buffercmp (102): Count: 254, Data is same. [CRZ] Buffercmp (102): Count: 255, Data is same. [CRZ] Buffercmp (102): Count: 256, Data is same. [CRZ] SRAM_Test (140): Test OK. 6. USB Host Test 4> USB Host Test 4 번을선택합니다. [CRZ] main (148): 4 is selected [CRZ] USB_Host_Test (211): [CRZ] USB_Host_Initialization (41): [CRZ] USB_Host_Initialization (49): FATFS_LinkDriver OK [CRZ] USBH_LL_Init (214): [CRZ] HAL_HCD_MspInit (45): [CRZ] HAL_HCD_MspInit (51): [CRZ] USB_Host_Initialization (53): USBH_Init done [CRZ] USB_Host_Initialization (57): USBH_RegisterClass done [CRZ] USB_Host_Initialization (61): USBH_Start done USB Device Attached PID: 6366h 6

7 VID: 58fh Address (#1) assigned. Manufacturer : Generic Product : Mass Storage Device Serial Number : 058F Enumeration done. This device has only 1 configuration. Default configuration set. Switching to Interface (#0) Class : 8h SubClass : 6h Protocol : 50h MSC class started. Number of supported LUN: 1 LUN #0: Inquiry Vendor : Multiple Inquiry Product : Card Reader Inquiry Version : 1.00 MSC Device ready MSC Device capacity : Bytes Block number : Block Size : 512 [CRZ] USB_Host_Test (224): Application state is START [CRZ] MSC_Application (76): [CRZ] f_mount (2486): [CRZ] f_mount (2492): vol: 0 [CRZ] MSC_Application (85): f_mount Ok [CRZ] f_open (2539): [CRZ] MSC_Application (128): f_open Ok [CRZ] MSC_Application (139): f_write Ok [CRZ] f_open (2539): [CRZ] MSC_Application (151): f_open Ok [CRZ] MSC_Application (162): f_read Ok [CRZ] MSC_Application (174): Compare read data Ok [CRZ] Wait_N_Seconds (41): Wait (1/1) second [CRZ] USB_Host_Test (240): Success demo OK cafe.naver.com/embeddedcrazyboys CRZ Technology 7

8 Success demo OK 가계속출력이됩니다. 7. Ethernet HTTP Test 5> Ethernet HTTP Test 5 번을선택합니다. [CRZ] main (148): 5 is selected [CRZ] Ethernet_HTTP_Test (72): [CRZ] Ethernet_HTTP_Test (76): lwip_init done [CRZ] HAL_ETH_MspInit (85): [CRZ] Ethernet_HTTP_Test (80): Netif_Config done [CRZ] Ethernet_HTTP_Test (84): httpd_init done [CRZ] Ethernet_HTTP_Test (88): User_notification done [CRZ] Ethernet_HTTP_Test (91): ethernetif_set_link done [CRZ] DHCP_Process (147): State: Looking for DHCP sever... [CRZ] DHCP_Process (172): IP address assigned by a DHCP server:

9 Led control 부분에서 LED1~3 부분을선택한후 Send 를누르면보드의 LED 3 개가켜집니다. 8. USB Device Test 6> USB Device Test 6 번을선택합니다. [CRZ] main (148): 6 is selected [CRZ] USB_Device_Test (29): [CRZ] USB_Device_Test (33): USBD_Init done cafe.naver.com/embeddedcrazyboys CRZ Technology 9

10 [CRZ] USB_Device_Test (37): USBD_RegisterClass done [CRZ] USB_Device_Test (41): USBD_CUSTOM_HID_RegisterInterface done [CRZ] USB_Device_Test (45): USBD_Start done 10

11 Graphic view 부분에서 Led 1~3 을제어하면실제보드의 LED 도함께동작하게됩니다. 9. RTC Calendar Test 7> RTC Calendar Test 7 번을선택합니다. [CRZ] main (148): 7 is selected [CRZ] RTC_Test (97): [CRZ] RTC_Test (132): Date: , Time: 02:00:00 [CRZ] RTC_Test (132): Date: , Time: 02:00:01 [CRZ] RTC_Test (132): Date: , Time: 02:00:02 [CRZ] RTC_Test (132): Date: , Time: 02:00:03 [CRZ] RTC_Test (132): Date: , Time: 02:00:04 시간이 1 초에한번씩출력되면정상입니다. 10. CAN Test 두보드를위사진과같이연결합니다. 붉은색박스와같이점퍼가연결되어야합니다. cafe.naver.com/embeddedcrazyboys CRZ Technology 11

12 8> CAN Test 8 번을선택합니다. [CRZ] main (148): 8 is selected [CRZ] CAN_Test (109): [CRZ] CAN_Test (132): ++ubkeynumber: 1 CanHandle->pRxMsg->Data[0]: 2 [CRZ] CAN_Test (132): ++ubkeynumber: 3 CanHandle->pRxMsg->Data[0]: 4 [CRZ] CAN_Test (132): ++ubkeynumber: 1 [CRZ] main (148): 8 is selected [CRZ] CAN_Test (109): CanHandle->pRxMsg->Data[0]: 1 [CRZ] CAN_Test (132): ++ubkeynumber: 2 CanHandle->pRxMsg->Data[0]: 3 [CRZ] CAN_Test (132): ++ubkeynumber: 4 CanHandle->pRxMsg->Data[0]: 1 [CRZ] CAN_Test (132): ++ubkeynumber: 2 12

13 CanHandle->pRxMsg->Data[0]: 2 [CRZ] CAN_Test (132): ++ubkeynumber: 3 CanHandle->pRxMsg->Data[0]: 4 CanHandle->pRxMsg->Data[0]: 3 [CRZ] CAN_Test (132): ++ubkeynumber: UART6 Test 9> UART6 Test 9 번을선택합니다 RS232 Test cafe.naver.com/embeddedcrazyboys CRZ Technology 13

14 디버그왼쪽편에하나의포트를더 PC 에연결합니다. 1> RS232 Test 1 번을선택합니다. 아래의결과에서왼쪽은디버그창이고오른쪽은하나더연결한 UART RS232 포트입니다. [CRZ] UART6_Test (174): 1 is selected [CRZ] UART6_Test (189): Rx: a (0x61) [CRZ] UART6_Test (189): Rx: b (0x62) [CRZ] UART6_Test (189): Rx: c (0x63) Test chars 1 Test chars 2 Test chars 3 Test chars 4 Test chars 5 Test chars 6 Test chars 7 1 초에한번씩 Test chars 를출력합니다. 오른쪽창에서입력한글자는왼쪽디버그창에출력이 됩니다 RS485 Test 두개의보드에서 RS485 포트부분을 1:1 로연결합니다. 14

15 2> RS485 Test 2 번을선택합니다. [CRZ] UART6_Test (174): 2 is selected abcdfsdfsdfsadfd [CRZ] UART6_Test (174): 2 is selected abcdwefwdfsdf 왼쪽디버그창에서입력한글자는오른쪽창에, 오른쪽창에서입력한글자는왼쪽창에나타나 게됩니다. cafe.naver.com/embeddedcrazyboys CRZ Technology 15

Mango220 Android How to compile and Transfer image to Target

Mango220 Android How to compile and Transfer image to Target http://www.mangoboard.com/ http://cafe.naver.com/embeddedcrazyboys Crazy Embedded Laboratory www.mangoboard.com cafe.naver.com/embeddedcrazyboys