ATX MID TOWER PC CASE User's Manual 한글 / English Ver.140210
English
1 Cautionary Note 1) Please read this manual thoroughly prior to installation. 2) Before installing, check the components and condition of the product, and if any problem is found, contact the retailer. 3) Avoid inserting objects or hands into the system while it is in operation to prevent product damage and injuries. 4) Check the manual when connecting cables. Incorrect connections may cause short circuits leading to fire hazards. 5) Do not block the front intake vent or the rear exhaust vent. ENG 6) Keep this unit away from heat sources, direct sunlight, water, oil, and humid environments, and place the unit on a flat, stable, vibration-free, and well-ventilated area. 7) Do not clean the product surface with chemicals or wet cloth. (chemicals: industrial brightener, wax, benzene, alcohol, paint thinner, mosquito repellent, aromatics, lubricant, detergent etc.) 8) Please wear gloves while handling this product to prevent injuries. 9) Product design and specifications may be revised to improve quality and performance. Disclaimer) Zalman Tech Co., Ltd. is not responsible for any damages due to external causes, including but not limited to, improper use, problems with electrical power, accident, neglect, alteration, repair, improper installation, or improper testing. 1
2 Product Details (1) Specifications Models Type Z9 U3 ATX Mid Tower Dimensions (W H D) 207(W) x 464(H) x 504(D)mm (8.1 x 18.2 x 19.8 ) Materials Color Motherboard Compatibility Power Supply Compatibility Plastic, Steel Black Standard ATX / m-atx Standard ATX / ATX12V PCI/AGP Card Compatibility Full Size 290 mm (11.4") 5.25 External Bay x 3 Drive Bays 3.5 External Bay x 1, Internal Bay x 5 5.25"/3.5"/2.5 1 (3in-1) Hot-swap - Expasion Card Solts I/O Ports Front 7 Slots Headphones x 1, USB 2.0 x 2, Mic x 1, USB 3.0 x 2 Fan Controller, Temperature display 120mm/140mm Fan Vent x 1 (1 Fan included) Cooling Components Top 120mm/140mm Fan Vent x 2 (1 Fan included, 1 optional) Rear 120mm Fan Vent x 1 (1 Fan included) Side - Bottom 120mm/140mm Fan Vent x 1 (Fan optional) 2
(2) Parts User manual ENG Main Unit Stand-Off 5 Bolt A(#6-32*6mm) 11 [PSU, PCI] Bolt B(M3*5mm) 17 [M/B, FDD, SSD] Bolt C(M3*6mm) 12 [5.25 Bay ODD] Bolt D(#6-32*4mm) 20 [3.5 Bay HDD] Bolt E(#6-32*6mm) 5 [3.5 HDD] HDD Anti-vibration rubber 20 [3.5 Bay HDD] PCI Slot 1 CPU 12V Extension Cable 1 Cable Tie 5 3
3 Installation (1) Side Panel Removal 2 1 (2) Motherboard Installation There are 4 Stand Offs preinstalled. Please refer to the diagrams below for additional Stand Off positions (based on motherboard type). ATX Board m-atx Board or Stand-Off B Bolt 4
(3) 5.25 and 3.5 Drive Installation 1) Front Cover Removal PULL ENG 2) ODD Installation Bolt C 3) 2.5 / 3.5 Tray Installation 1 Tray removal Bolt C 5
2 Attach Drive to Tray A. 3.5 FDD Installation B. 3.5 HDD Installation 3.5 HDD 3.5 FDD Bolt B Bolt A C. 2.5 SSD Installation SSD Bolt B (4) Front Cover Installation When removing the front cover, the power switch and extension cable are separated to prevent disconnection. Be sure to connect them before installing the front cover. 6
ENG Z9 U3 (5) 3.5 HDD Installation HDD Bolt D HDD Antivibration rubber When transporting an assembled system, please secure the HDD with Bolt E as shown above. When removing HDD, pull the fastening lever outwards and then remove it. Bolt E (6) Cable Connection Power Button Fan Connection or or Power LED Mother Board PSU Power Mother Board (3-Pin Fan Connector) 7
I/O Port USB 3.0 or USB 3.0 MotherBoard MotherBorad I/O Power and I / O ports to connect please refer to your motherboard. manual. Product design and specifications may be revised to improve quality and performace. (7) 2.5 HDD / SSD Optional 2.5" HDD and SSDs can be installed on the right side of case as shown in the diagram below. Bolt B (8) Optional Fan Installation and Replacement Top Panel Fan (120/140 mm) Installation When installing fan, press the Top Panel s eight Hook s towards each other to remove and install as shown in diagram below. The Z9U3 comes with one 120mm Fan pre-installed. 8 8
한 글
1 1) 설치전제품설명서를반드시숙독하시기바랍니다. 2) 설치전구성품및제품의상태를반드시확인하시고이상이있을경우구입처에상담하시기바랍니다. 주의사항한글3) 동작중인제품에손이나물체를넣지마십시오. 인체및제품에해를끼칠수있습니다. 4) 케이블을연결할때반드시매뉴얼을확인한후연결하십시오. 잘못연결할경우합선으로인한화재의우려가있습니다. 5) 제품의전면과후면에있는통풍구가막히지않도록주의하십시오. ENG 6) 직사광선이들어오는곳이나난방기주변등열이발생하는곳, 물 ( 빗물 ) 이튀는곳, 기름및습기가많은곳을피하여공기가잘통하고, 평탄하며진동이없는곳에설치하십시오. 7) 화학약품등으로제품표면을닦지마십시오. ( 화학약품, 공업용광택제, 왁스, 벤젠, 알코올, 신나, 모기약, 방향제, 윤활제, 세정제등 ) 8) 잘못설치하여발생되는문제에대해서당사는책임지지않으므로반드시설명서를참조하여설치해주시기바랍니다. 9) 정해진용도이외의사용으로인하여발생하는문제에대하여당사는어떠한책임도지지않습니다. 10) 본제품취급도중상처및사고예방을위해장갑을반드시착용하여주십시오. 11) 제품의외관디자인및규격은제품의품질향상을위하여소비자에게예고없이변경될수있습니다. 1
PCI / AGP 카드규격 Full Size 290 mm (11.4") 드라이브베성요소Z9 U3 2 제품개요 (1) 제품사양 구분타입 Z9U3 ATX Mid Tower 크기 (W H D) 207 464 504 mm (8.1 18.2 19.8 ) 재질색상지원마더보드규격지원파워서플라이규격 플라스틱, 스틸 Black Standard ATX / m-atx Standard ATX / ATX12V 이5.25"/3.5"/2.5" 1개 (3in-1) 5.25 외장 3개 3.5 외장 1개, 내장 5개 Hot-swap - 확장슬롯 7개쿨링구전면 상단 120mm또는 140mm팬 1 ( 기본장착 ) 120mm또는 140mm팬 2 (1 기본장착, 1 옵션 ) 후면 120 mm팬 1( 기본장착 ) 측면 - 하단 120 mm또는 140 mm팬 1( 옵션 ) 전면 I/O 포트 마이크 1 / 헤드폰 1 / USB 2.0 4 / USB 3.0 x 2 팬컨트롤러, 온도표시창 2
(2) 구성품 설명서 1 부 ENG 본체 Stand-Off 5 A 나사 (#6-32*6mm) 11 [PSU 장착용, PCI 슬롯고정용 ] B 나사 (M3*5mm) 17 [M/B, FDD, SSD 장착용 ] C 나사 (M3*6mm) 12 [5.25 베이 ODD 장착용 ] D 나사 (#6-32*4mm) 20 [3.5 베이 HDD 장착용 ] E 나사 (#6-32*6mm) 5 [3.5 HDD 고정용 ] HDD 방진고무 20 [3.5 베이 HDD 장착용 ] PCI 슬롯 1 CPU 12V 연장케이블 1 케이블타이 5 3
3 설치방법 (1) Side Panel 분리 2 1 (2) 마더보드설치 기본 4 개의 Stand-Off 가장착되어있으며, 하단그림을참조하여마더보드타입에따라 Stand-Off 를추가로끼우고 B 나사로마더보드를케이스에장착합니다. ATX Board or m-atx Board Stand-Off B 나사한글4
(3) 5.25 및 3.5 드라이브설치 1) Front Cover 분리 PULL ENG 2) ODD 설치 C 나사 3) 2.5 / 3.5 트레이설치 1 트레이분리 C 나사 5
2 트레이에드라이브장착 A. 3.5 FDD 설치시 B. 3.5 HDD 설치시 3.5 FDD 3.5 HDD 한B 나사 A 나사글C. 2.5 SSD 설치시 B 나사 Front Cover를분리할때케이블단선방지를위해전원버튼과연장케이블이분리되어있습니다. Front Cover 장착전에전원버튼과연장케이블을반드시연결하시기바랍니다. SSD (4) Front Cover 장착 6
ENG Z9 U3 (5) 3.5 HDD 장착 HDD D 나사 HDD 방진고무 조립후시스템을이동할때는해당위치에 E 나사로 HDD 를고정해주시기바랍니다. HDD 를분리할때는나사를제거한후고정레버를적당히밖으로당긴후분리하십시오. E 나사 (6) 케이블연결 전원버튼 팬전원연결 or or Power LED 마더보드 PSU 전원 마더보드 (3핀팬커넥터 ) 7
I/O 포트 8 마더보드마더보드 I/O 단자 전원및 I/O 포트연결시마더보드매뉴얼을참고하시길바랍니다. 제품의외관디자인및규격은제품의품질향상을위하여소비자에게예고없이변경될수있습니다. (7) 2.5 HDD / SSD 추가장착 다음그림과같이케이스오른쪽측면에 SDD 를장착하여사용할수있습니다. (8) 팬추가장착및교체 ( 옵션 ) B 나사 상단팬교체 (120 / 140 mm팬설치가능 ) 팬교체 / 튜닝시상단커버의후크 (8 개 ) 를안쪽으로눌러분리한후아래그림과같이장착합니다. Z9U3 는 120 mm팬 1 개가기본장착되어있습니다. 8 한글USB 3.0 or USB 3.0
4 품질보증및 A/S 안내 1. 제품보증기간 : 제품구입일로부터 1 년 ( 단, 구입영수증이있을때 ) 2. 무상 A/S: 품질보증기간내에제품자체성능상의하자및불량발생시 3. 유상 A/S: 품질보증기간이후에제품사용상의문제발생시. 단, 아래와같은사항에대해서는품질보증기간이내라도무상 A/S 처리가되지않으며소비자부담으로처리됩니다. 본사용설명서에명시된설치전주의사항및유의사항을지키지않은경우 사용자의고의나과실및부주의로인하여변형 / 파손 / 파괴된경우 사용자의임의개조에의한변형및고장이발생된경우 4. 교환및환불 1) 교환 : 제품구입일로부터 1 개월이내에제품자체성능상의하자또는불량발생시동일제품으로교환하여드립니다. 2) 환불 : 제품구입후 10 일이내에제품및포장의훼손이없는경우에만구입처를통해환불받으실수있습니다. ( 단, 제품구입시발급해드린영수증을제시하셔야환불가능합니다 ) 5. A/S 1) 운영시간 : 평일 09:00~18:00 ( 공휴일, 토 일요일휴무 ) 2) 접수방법 1 방문접수 : 직접방문할경우사전연락후방문해주시기바랍니다. 2 택배접수 : 택배 ( 우편 ) 를이용하실경우아래의주소로성함, 주소, 연락처및불량상태를적은메모지를넣어서보내주십시오. 3) 접수처 총판 ( 아이구주 ): 서울시용산구한강로 2 가 16-1 선인상가 21 동 3 층 126-128 호 070-8250-1428 ENG 6. 제품운송비용 1) 무상 A/S 의경우 : 전액당사가부담합니다. 2) 유상 A/S 의경우 : 당사로보내시는비용은고객이부담하시고, A/S 처리후발송하는비용은당사가부담합니다. 3) 보증기간이후 : 전액고객부담입니다. 9
Zalman Tech Co., Ltd. #1007 daeryung Techno Town III, 448 Gasan-dong, Gumchun-gu, Seoul, 153-803,Korea Tel: +82-2-2107-3232 / Fax: +82-2-2107-3322 / www.zalman.com / e-mail: zalman@zalman.com Zalman USA, Inc. 10531 Garden Glove Blvd., Garden Grove, CA 92843, U.S.A Tel: +1-714-530-0700 / Fax: +1-714-530-0707 / www.zalman.com / e-mail: zalman@zalmanusa.com