EN Important Safety Information Explanation of Attention Words and Symbols used in this guide WARNING indicates a hazardous situation which, if not av

Transcription

1 Operating Guide 사용설명서 D360KA-RE 360 Pet Fountain Litres 360 애완동물분수대 리터 Please read this entire guide before beginning 사용하기전에본설명서전체를읽어보십시오

2 EN Important Safety Information Explanation of Attention Words and Symbols used in this guide WARNING indicates a hazardous situation which, if not avoided, could result in death or serious injury. CAUTION, used without the safety alert symbol, indicates a hazardous situation which, if not avoided, could result in harm to your pet. NOTICE is used to address safe use practices not related to personal injury. When using electrical appliances, basic safety precautions should always be followed to reduce the risk of fire, electric shock and/or injury to persons, including the following: To reduce the risk of injury, close supervision is necessary when an appliance is used by or near children. To protect against electric shock, do not place Power Cord or plug in water or other liquids. Only use attachments recommended or sold by the manufacturer. Do not use outdoors. FOR INDOOR HOUSEHOLD USE ONLY. Do not unplug by pulling on Power Cord. To unplug, grasp the plug, not the Power Cord. Do not operate any appliance if it has a damaged Power Cord or plug, or if it is malfunctioning or has been damaged. Call Customer Care Centre immediately for further instructions. For a portable appliance - To reduce the risk of electrical shock, do not place or store an appliance where it can fall or be pulled into a tub or sink. Always unplug any appliance when not in use, before putting on or taking off parts and before cleaning. Never pull on the electrical Power Cord to remove the plug from the wall outlet. Do not use an appliance for anything other than its intended use. If the plug of this device gets wet, turn off the electricity to that outlet. Do not attempt to unplug. Examine this appliance after installation. Do not plug in if there is water on the Power Cord or plug. 2

3 Do not allow pets to chew on or swallow any parts. If you are concerned about the Power Cord, purchase a cord conduit (a hard plastic protector) at any hardware store. The Pet Fountain parts are BPA-FREE. However, some animals have been known to be sensitive to plastic food and water containers. If your animal shows signs of an allergic reaction to the plastic, please discontinue use until you have consulted with your veterinarian. The Pet Fountain is intended to run continuously (always plugged into electricity), as long as the water level is maintained and the Pet Fountain is cleaned regularly. Be sure to check the Pet Fountain regularly to help prevent damage to the Pump, as the water may get consumed or evaporate causing the Pump to run dry. Do not attempt repairs on the Pump yourself. To avoid the possibility of the plug or outlet getting wet, the outlet should always be above the level of the Pet Fountain. If an extension cord is necessary, an extension cord with a proper rating should be used. The electrical use of this appliance is 2 watts. Do not use appliance for anything other than intended use. The use of attachments not recommended or sold by the manufacturer may cause an unsafe condition. Do not modify the unit. Do not install or store appliance where it will be exposed to weather or temperatures below 4.5 C. Read and observe all important notices listed on the appliance and in the packaging. EN SAVE THESE INSTRUCTIONS 3

4 EN Thank you for choosing the PetSafe brand. You and your pet deserve a companionship that includes memorable moments and a shared understanding together. Our products promote a lifestyle of protection, teaching and love; essentials that influence memories for a lifetime. If you have any questions about our products, please visit our website at or contact our Customer Care Centre. Table of Contents Components...5 Features...5 Key Definitions...6 Operating Instructions...7 Pet Fountain Disassembly and Cleaning...9 Pump Maintenance...10 Pet Fountain Reassembly...12 The Pet Fountain and Your Environment...13 General Tips...13 Warranty and Customer Care...14 Compliance...14 Important Recycling Advice...14 Terms of Use and Limitation of Liability...15 Korean

5 Components Cone EN Filter Housing Filter Filter Housing Cap Pump/Motor & Low Voltage Adapter In-Line plug & Power Cord Interchangeable Spout Rings (5 versions) Intake Tube Bowl Foam Filter Flow Control Cap Intake Tube Holder Note: Your Pet Fountain will come partially assembled, however, it is a good idea to make sure none of the Pet Fountain pieces have come loose in shipping. Features Cone reduces splash and sound of falling water Adjustable Flow Control Cap Replaceable Charcoal Filter removes bad tastes and odors Dishwasher safe (excluding pump) 3.8 L Water Capacity Low-Voltage (12V) System Submersible pump for quiet operation Foam Filter keeps pump cleaner by catching hair, debris and pet food 5

6 EN Key Definitions Bowl: The Bowl is the foundation of the Pet Fountain. The circular bowl piece can be carried by simply gripping the sidewalls underneath the Bowl. In addition, the bottom of the Bowl features cord clips to hide the Power Cord from view. Cone: The Cone acts as the housing for the Pet Fountain components and protects the Pump from curious pets. The Cone acts to reduce the splash and sound of the falling water. It also houses a majority of the water and holds the Filter Housing and subsequent parts. Filter Housing: The Filter Housing slides into the opening at the top of the Cone. It houses the Filter and locks into the Cone by twisting the entire Filter Housing a quarter turn. Charcoal Filter: The cylindrical Charcoal Filter features a pull-tab at the top and should be placed in the Filter Housing with the pull-tab facing upwards for easy placement and removal. Filter Housing Cap: The Filter Housing Cap is a screw on Cap that attaches to the Filter Housing to keep the Filter in place. It serves as the base piece to attach the Interchangeable Spouts & Flow Control Cap. Foam Filter: The Foam Filter collects hair, debris and pet food before they reach the Pump. It is important to use the Foam Filter as it helps maintain proper Pump function. Spout Rings: The Pet Fountain features five Interchangeable Spout rings that can be easily changed based upon your pet s preference and can provide up to 5 streams of water for multiple pet households. Flow Control Cap: The Flow Control Cap is attached to the top of the Pet Fountain and adjusts the flow of water by simply turning the Flow Control Cap left or right. Turn to the right to increase the flow of water. Turn to the left to decrease. Pump: A small Low Voltage submersible aquarium pump that can be dismantled for cleaning. Important: THE PUMP IS NOT DISHWASHER SAFE! Remove Pump from Pet Fountain prior to cleaning. (See Pump Maintenance ) The pump cord features a detachable In-Line plug for easy removal. 6

7 Operating Instructions Important: DO NOT RUN DRY - FOR INDOOR USE ONLY. EN 1. As with any electrical device, check the electrical cord for any tears, or damage before use. 2. Make sure the In-Line Plug is connected (No silver showing - Fig. 1). Fig Remove Cone piece by twisting counter clockwise to unlock the tabs from the bowl. Lift up and set aside (Fig. 2). 4. Check to make sure the Intake Tube is properly inserted (pushed all the way down) into the Pump (Fig. 3). 5. Replace Cone and twist clockwise to lock tabs in place (Fig. 4). 6. Take the partially assembled Filter Housing and remove the Flow Control Cap by gently lifting straight up - DO NOT TWIST TO REMOVE (Fig. 5). Gently lift up on the Spout Ring to access the Filter Housing Cap. Fig. 3 Fig. 2 Fig. 4 UNLOCKED LOCKED 7. Unscrew Filter Housing Cap and insert the Filter into the Filter Housing with the pull-tab facing up (Fig. 6). The Filter will slide easily into place. Next, screw on the Filter Housing Cap (Fig. 7). Fig. 5 Fig. 6 Fig. 7 Important: Rinse the Filter thoroughly under cool water before placing into the housing. This will remove any loose charcoal dust, which is harmless to your pet. A small amount of charcoal dust may be gradually released for the life of the Filter. This is normal and not harmful to your pet. The Filter should be replaced every two weeks for best performance. Filters may need to be changed more frequently depending on the number of pets using the Pet Fountain. 7

8 EN 8. Align the side grooves of the Filter Housing with the inner notches of the Cone opening. The Filter Housing should slide easily into place. Turn housing a quarter turn to the right (clockwise) until it locks in place. (Fig. 8) 9. Select one of the five interchangeable Spout Rings based upon your personal preference or your pet s. Place the chosen Spout Rings on top of Filter Housing Cap and gently press down evenly to secure in place. (Fig. 9) 10. Align Flow Control Cap with the raised notches (Fig. 10) on the Filter Housing Cap. Press down gently and the cap will snap into place. With the Flow Control Cap, you will be able to easily adjust the flow intensity of the water. Turn the cap to the right to increase the flow and turn to the left to decrease. Important: If you notice a decrease in the flow of the water that is not corrected by turning the flow control cap toward max this may be an indication of a clogged and dirty Filter and/or the need to rinse and clean the Filter housing. Consult the Pet Fountain Disassembly and Cleaning section of this manual for details on cleaning and maintaining your Pet Fountain. 11. Place Pet Fountain in desired location. IMPORTANT: To take care of your floors, always use a protective mat, such as a towel or place mat. This will help protect your floor from any water that may splash out from your pet s use of the Pet Fountain. 12. Fill the Pet Fountain Bowl with water. Make sure the water level is at least to the MIN (minimum) fill line so the pump does not run dry. This will prime the pump for use. Do not fill the Pet Fountain past the MAX (maximum) fill line. 13. Before you plug in the Pet Fountain make sure the Power Cord and your hands are dry. Plug the Pet Fountain in to a standard wall outlet. 14. Add water as needed. Never let the water level fall lower than the MIN (minimum) fill line (approx. 25 mm above the bottom of the bowl, Fig. 11) or the Pump may fail. IMPORTANT: Never pick up a full Pet Fountain by the Cone piece. To properly pick up the Pet Fountain, use both hands and grip the sidewalls of the Pet Fountain Bowl and lift. Groove Raised Notches Fig. 8 Notch Fig. 9 Fig. 10 Fig

9 Pet Fountain Disassembly and Cleaning Important: Pet Fountain must be cleaned to continue working normally. FILTER SYSTEM The Pet Fountain is equipped with two types of filters that should be replaced on a regular basis. The Charcoal Filter removes bad tastes and odours, keeping water fresh. The Foam Filter collects hair, debris and pet food and prevents them from reaching the Pump, providing optimal filtration. The filters together will keep the Pump cleaner and provide fresher water to your pet. Charcoal Filter: Filters should be changed every two to four weeks. Replace filters more frequently when using the Pet Fountain for multiple pets or pets that produce a lot of saliva. Important: Always rinse the Charcoal Filter prior to use. A small amount of charcoal dust may be released for the life of the filter, this is normal and is not harmful to your pet. Foam Filter: Replace the Foam Filter every one to two months, depending on the location of the Pet Fountain and the number of pets using it. If you do not intend to replace the filter at the time of cleaning, rinse the Foam Filter thoroughly with fresh water. Filters are an added feature of the Pet Fountain. Using the filters is not required for normal operation. However, when used properly and changed regularly, the filters help keep the water cleaner and fresher, while extending the life of your Pet Fountain. Filters may be rinsed out when the Pet Fountain is cleaned. Important: Never wash the filters with soapy water, as the soap residue will seep into the filters and cannot be removed. Only rinse the filters with water. PET FOUNTAIN: Clean once a week. 1. Unplug Pet Fountain from electrical source and disconnect the In-Line Plug (Fig. 1). 2. Remove the Flow Control Cap and Spout Ring. 3. Remove the Filter Housing by twisting the Filter Housing to the counter clockwise to the unlock position. Lift directly up and set aside. 4. Empty the water out of the Pet Fountain. 5. Once the Pet Fountain is empty, remove the Cone piece by twisting to the counter clockwise to unlock the tabs. Lift up and set aside (Fig. 2). 6. Next, flip the Bowl upside down and unhook the Power Cord from the two Cord Clips (Fig. 12). This will allow you to pull the cord through the Power Cord Pass-Through in the Bowl. (Fig. 13) Cord Pass-Through Fig. 12 Fig. 13 EN Cord Clips 9

10 EN 7. Remove the Pump for cleaning. First remove the Intake Tube by lifting up on the Intake Tube Holder to free the Intake Tube from the Pump. (Fig. 14 & 15) This will allow you to remove the Pump. The intake tube can then be pulled from the intake tube holder. (See Pump Maintenance for detailed cleaning instructions for the Motor/Pump) Fig. 14 Fig Remove the Foam Filter from the Pump. Clean away any hair, debris or pet food that may have accumulated on the Faceplate of the Pump (See Pump Maintenance for detailed cleaning instructions for the Pump). 9. Clean the Pet Fountain parts with warm water and soap. You can also put the Pet Fountain in the top rack of the dishwasher. Remove the pump before placing the Pet Fountain in the dishwasher. DO NOT PLACE PUMP IN DISHWASHER! If possible, it is recommended that you turn down the heat of the water inside the dishwasher. 10. If you have troubles reaching certain spots or hard-to-reach corners, try using a cotton swab or purchase the Drinkwell Cleaning Kit, a 3-Piece Brush kit. To purchase a cleaning kit, visit our website at to locate a retailer near you or to find a listing of Customer Care Centre telephone numbers for your area. Pump Maintenance Important: Cleaning the Pump is essential to the longevity of the Pet Fountain as well as the cleanliness of the water. Clean the Pump at least every two weeks. Warranty may be voided if the Pump is not cleaned regularly. Intake Plate Faceplate Pump Impeller 10

11 1. Remove Pump from the Pet Fountain as explained in the Pet Fountain Disassembly and Cleaning section (specifically steps 6 & 7). 2. Once the Pump is out of the Pet Fountain, with your thumb and forefinger, gently squeeze on either side of the Faceplate, and pull off. It may be necessary to insert a fingernail into the seam of the Faceplate to pry it off. 3. Next you will want to remove the Intake Plate by placing your fingernail under the small lip located on the narrow side of tear drop shaped Intake Plate and pull out (Fig. 16). EN Intake Plate Pull-Tab Fig Once the Intake Plate is removed you can also remove the Impeller (white Fig bladed propeller) which is held in place magnetically. To remove the Impeller use a fingernail to get under the plastic blade and lift out (Fig. 17). 5. Once the Motor is disassembled you can clean the parts with warm soapy water. Use a cotton swab or the motor brush from the Drinkwell Cleaning Kit to get into the Motor cavity and remove any build-up (Fig. 18). Fig. 18 For added disinfecting and hard water removal, clean the Motor with a 20% white vinegar & 80% water solution. Be sure to rinse thoroughly with fresh water. 6. Once the parts are clean you can reassemble the Pump for use. a) Replace the Impeller b) Replace the Intake Plate c) Replace the Faceplate. 11

12 EN Pet Fountain Reassembly 1. Place the Foam Filter around the Pump. Make sure the electrical Power Cord runs over the top of the Foam Filter, not underneath it, as this will keep the Foam Filter in place. 2. With the Foam Filter securely around the Pump, replace the Pump into its location between the four, 12.5 mm posts in the center of the Bowl. Be sure to position the hole on the top of the Pump next to the electrical power cord Pass-Through in the Bowl. Gently push down to engage the suction cups. 3. Replace the Intake Tube into the Intake Tube Holder, then place the Intake Tube Holder back onto the electrical power cord Pass-Through post aligning the guideline on the post with the notch in the Intake Tube holder. Be careful to align the Intake Tube so that it fits into the hole on the top of the Pump. 4. Thread the In-Line Plug through the opening next to the Pump. On the bottom side of the Bowl, clip the Cord into place using the Cord Clips (Fig. 12). Next, thread the Power Cord directly out the Pet Fountain through the Cord Pass- Through (Fig. 12 & 13). Use this Pass-Through to keep the Power Cord from showing. 5. Align the three notches around the Cone with the corresponding tabs in the bowl. Next, turn the Cone piece to the right (clockwise) to lock tabs into place. (Fig. 2 & 4) 6. After cleaning your Pet Fountain it is a good idea to replace your Filter. 7. Screw on Filter Housing Cap and slide the Filter Housing into place in the hole at the top of the Cone. Turn Filter Housing a quarter turn to the right (clockwise) to lock in place. 8. Choose your preferred Spout Ring (1 spout up to 5 spouts) and place on top of the Filter Housing Cap, press it gently into place. Be sure it is pushed down evenly all the way around. 9. Replace the Flow Control Cap by aligning the cap with the notches on the Filter Housing Cap and gently pushing down. 10. Place Pet Fountain in desired location and fill with water to the MAX (maximum) fill line. 11. With dry hands reconnect the In-Line Plug and then plug Pet Fountain in. Adjust the flow to your preference and let your pet enjoy the fresh free falling water of the Pet Fountain. 12

13 The Pet Fountain and Your Environment If you live in a humid environment and have problems with mold or algae, soak all fountain parts in a diluted vinegar solution (20% White Vinegar and 80% Water) for 10 minutes after regular cleaning. Also, pour the diluted vinegar solution into the motor cavity. If you have hard water, small white mineral deposits may form on or inside the Pump. This can eventually prevent the Impeller from turning properly. To avoid replacement or damage to the Pump, please take the following precautions: 1. Clean the Pump more frequently. 2. Clean the Pump with a diluted vinegar solution weekly. 3. Use bottled water instead of tap water. EN General Tips When being introduced to the Pet Fountain, your pet may be cautious of this new and unusual object. After beginning operation of your Pet Fountain, simply allow your pet to adjust at his or her own pace. Some pets may take several days or longer to begin use, while others will start right away. Your pet may prefer that the Pet Fountain be placed away from their normal feeding area. Try placing it in another location, such as a different area of the kitchen or in a bathroom or utility room. Add ice cubes to the bowl for refreshing, ice-cold running water! 13

14 EN Warranty and Customer Care This product has the benefit of a 1 (one) year limited manufacturer s warranty. This warranty does not cover damage from accidents, misuse or abuse. It also specifically excludes incidental or consequential damages as allowed by law. Loss of function as a result of lack of cleaning, debris or mineralization from hard water does not qualify under this warranty (Refer to cleaning instructions and environmental notes). Details of the warranty applicable to this product and its terms can be found at and/or are available by sending an to: asiacc@petsafe.net. Please contact your local Customer Care Centre with any set-up or technical difficulties you experience, and if necessary to assist in the replacement of your product. For a listing of Customer Care Centres in your area, visit our website at Compliance This equipment complies with the EMC and Low Voltage Directives. Unauthorized changes or modifications to the product that are not approved by Radio Systems Corporation may violate EU regulations, could void the user s authority to operate the equipment, and will void the warranty. The Declaration of Conformity can be found at: Important Recycling Advice Please respect the Waste Electrical and Electonic Equipment regulations in your country. This equipment must be recycled. If you no longer require this equipment, do not place it in the normal municipal waste system. Please return it to where it was purchased in order that it can be placed in our recycling system. If this is not possible, please contact the Customer Care Centre for further information. 14

15 Terms of Use and Limitation of Liability 1. Terms of Use Use of this Product is subject to your acceptance without modification of the terms, conditions and notices contained herein. Use of this Product implies acceptance of all such terms, conditions and notices. If you do not wish to accept these terms, conditions, and notices, please return the Product, unused, in its original packaging and at your own cost and risk to the relevant Customer Care Centre together with proof of purchase for a full refund. 2. Proper Use If you are unsure whether this Product is appropriate for your pet, please consult your veterinarian or certified trainer prior to use. Proper use includes, without limitation, reviewing the entire Operating Guide and any specific safety information statements. 3. No Unlawful or Prohibited Use This Product is designed for use with pets only. Using this Product in a way that is not intended could result in violation of Federal, State or local laws. 4. Limitation of Liability In no event shall Radio Systems Corporation or any of its associated companies be liable for (i) any indirect, punitive, incidental, special or consequential damage and/or (ii) any loss or damages whatsoever arising out of or connected with the misuse of this Product. The Purchaser assumes all risks and liability from the use of this Product to the fullest extent permissible by law. For the avoidance of doubt, nothing in this clause 4 shall limit Radio Systems Corporation s liability for human death or personal injury or fraud or fraudulent misrepresentation. 5. Modification of Terms and Conditions Radio Systems Corporation reserves the right to change the terms, conditions and notices governing this Product from time to time. If such changes have been notified to you prior to your use of this Product, they shall be binding on you as if incorporated herein. EN Covered by: U.S. Patents No. 5,799,609 and 5,842,

16 EN 중요안전정보 본설명서에서사용하는주의용어및기호설명 경고는피하지않을경우사망또는심각한상해로이어질수있는위험한상황을나타냅니다. 주의는안전경보기호없이사용되는경우피하지않으면애완동물에해를입힐수있는위험한상황을나타냅니다. 안내는신체상해와관련되지않은안전사용방식을다루는데사용됩니다. 전기기구사용시화재, 감전및 / 또는신체상해의위험을줄이기위해다음사항을비롯한기본안전수칙을항상따라야합니다 : 기구를어린이옆에서또는주변에서사용하는경우부상위험을줄이기위해철저하게살펴야합니다. 감전방지를위해전기코드나플러그를물이나기타액체안에넣지마십시오. 제조업체가권장하거나판매하는부속장치만사용하십시오. 옥외에서사용하지마십시오. 가정실내전용. 플러그를뺄때전기코드를잡아당기지마십시오. 플러그를뺄때전기코드가아니라플러그를잡으십시오. 기구의전기코드나플러그가손상되거나기구가고장나거나손상된경우기구를작동하지마십시오. 즉시고객지원센터에연락하여자세한지침을받으십시오. 휴대용기구의경우 - 감전위험을줄이기위해떨어지거나욕조나싱크에끌려들어갈수있는곳에기구를놓거나보관하지마십시오. 사용하지않을때, 부품을탈착하기전에그리고청소하기전에는항상기구의전원플러그를빼십시오. 절대로전기코드를당겨서플러그를벽콘센트로부터빼내지마십시오. 원래용도이외의용도로기구를사용하지마십시오. 본기구의플러그가젖은경우, 그콘센트에공급되는전기를끄십시오. 플러그를빼려고하지마십시오. 본기구를설치한후에검사하십시오. 전기코드나플러그에물이있으면플러그를꽂지말아야합니다. Korean 16

17 애완동물이부품을씹거나삼키지못하게하십시오. 전기코드에대해염려가될경우전기상에서전선관 ( 단단한플라스틱보호관 ) 을구입하십시오. 분수대부품에는 BPA가없습니다. 그러나어떤동물들은플라스틱식기및물그릇에민감한것으로알려져있습니다. 애완동물이플라스틱에대해알레르기반응의징후를보이는경우수의사와상의하기전까지는기구사용을중단하십시오. 분수대는수위가유지되고분수대를정기적으로청소하는한계속작동하도록설계되었습니다 ( 항상플러그를전원에꽂아둠 ). 물이다소비되거나증발되어펌프가물없는상태에서작동될수있으므로분수대를정기적으로점검하여펌프에손상이발생하지않도록해야합니다. 모터를직접수리하려고시도하지마십시오. 플러그나콘센트가젖을가능성을피하기위해콘센트는항상분수대보다더높은위치에있어야합니다. 연장코드가필요한경우적절한등급의연장코드를사용해야합니다. 본기구의전기사용량은 2 와트입니다. 원래용도이외의용도로기구를사용하지마십시오. 제조업체가권장하거나판매하지않는부속장치를사용할경우위험한상태가초래될수있습니다. 기구를개조하지마십시오. 이 4.5 이하날씨온도에노출되는곳에기기를설치하거나보관하지마십시오 C. 기구와포장에표시된모든중요고지사항을읽고준수하십시오. EN 이수칙을보관하십시오 17

18 EN PetSafe 브랜드를선택해주셔서감사합니다. 고객님과고객님의애완동물은추억에남을만한순간들과마음을같이한것을비롯하여서로정을나누는사이입니다. 저희의제품은평생동안추억에영향을미칠필수요소인보호, 가르침및사랑의생활방식을촉진합니다. 저희제품에대해궁금한점이있으시면저희웹사이트 를방문하거나고객지원센터에문의하십시오. 목차구성품 특징 중요기능 작동설명 분수대분해및청소 폄프유지보수 분수대재조립 애완동물분수대와환경 사용요령 품질보증및고객서비스 준수 중요한재활용정보 사용조건과배상책임의한계

19 구성품 필터하우징 콘 EN 필터 필터하우징캡 펌프 / 모터및저전압어댑터 인라인플러그및전기코드 교환사용가능주둥이링 (5 개버전 ) 흡입관 용기포움필터유량조절캡흡입관홀더 참고 : 분수대는부분조립상태로공급되지만운송도중에분수대의부품이헐거워지지않았는지확인하는것이좋습니다. 특징 조절가능한유량제어 콘은물이튀는것과떨어지는물의소음을줄이는역할을합니다 식기세척기로세척가능 ( 펌프제외 ) 3.8 L 물용량저전압 (12V) 시스템 교체가능한숯필터는나쁜맛과악취를제거합니다 조용히작동되는수중펌프 교체가능폼필터는털, 오물및애완동물사료를걸러내므로펌프와물을깨끗하게유지합니다 19

20 EN 중요기능 용기 : 용기은분수대의기초입니다. 둥근용기은보울아래측벽을잡아서나르면됩니다. 아울러용기의바닥에는전기코드가보이지않게하기위한 " 코드클립 " 이갖추어져있습니다. 콘 : 콘은분수대구성품들을위한하우징역할을하며호기심이많은애완동물들로부터펌프를보호합니다. 콘은물이튀는것과떨어지는물의소음을줄이는역할을합니다. 또한다량의물을수용하며필터하우징과후속부품들을고정합니다. 필터하우징 : 필터하우징은콘의상단에있는구멍안으로들어갑니다. 필터를수용하며전체필터하우징을사분의일바퀴회전함으로써콘과맞물려고정됩니다. 필터 : 원통형필터는상단에당김용고리가있으며용이한설치및제거를위해당김고리가위를향하도록필터하우징내에설치해야합니다. 필터하우징캡 : 필터하우징캡은필터를제자리에유지하기위해필터하우징에부착되는나사형캡입니다. 이캡은교환사용가능한주둥이와유량제어캡을부착키위한바닥판역할을합니다. 포움필터 : 포움필터는털, 오물및애완동물사료를걸러서펌프로가지않게하는적합한여과기능을제공합니다. 포움필터는펌프의정상적작동을유지하는데도움이되므로반드시사용해야합니다. 주둥이링 : 분수대는애완동물의취향에따라쉽게바꿀수있으며여러애완동물이있는가정을위해물흐름을 5개까지제공할수있는다섯개의교환사용가능주둥이링을갖추고있습니다. 유량조절캡 : 유량조절캡은분수대의상단에부착되며유량조절캡을단순히왼쪽이나오른쪽으로돌려서유량을조절합니다. 유량을늘리려면오른쪽으로돌리십시오. 줄이려면왼쪽으로돌리십시오. 펌프 : 청소를위해분해되는소형저전압수중어항펌프. 중요 : 이펌프는식기세척기에서세척하면손상될수있습니다! 청소전에분수대에서펌프를빼내십시오. (" 폄프유지보수 " 항참조 ) 펌프코드는용이한분리를위한분리가능인라인플러그를갖추고있습니다. 20

21 작동설명중요 : 건조상태에서작동하지마십시오 - 실내전용. 1. 모든전기기구와마찬가지로사용전에전기코드가갈라지거나손상되지않았는지 그림 1 점검하십시오. 2. 인라인플러그가연결되었는지확인하십시오 ( 은색이보이지않아야함 - 그림 1 참조 ). 3. 반시계방향으로돌려서탭을용기로부터잠금 해제하여콘을분리하십시오. 들어올려서옆에 놓으십시오 ( 그림 2 참조 ). 4. 흡입관이펌프에올바로삽입되어있는지 ( 끝까지내리누름 ) 확인하십시오 ( 그림 3 참조 ). 5. 잠금해제됨콘을설치하고시계방향으로돌려서탭이제자리에잠기게하십시오 ( 그림 4 참조 ). 그림 2 6. 부분적으로조립된 필터하우징에서유량 제어캡을조심해서 똑바로위로올려서 빼내십시오 - 뒤틀어서 잠겨짐 빼지마십시오 ( 그림 5 참조 ). 필터하우징캡에액세스하기위해주둥이 그림 3 그림 4 링을부드럽게들어올리십시오. 7. 필터하우징캡을돌려서빼고당김고리가위로가게하여필터를필터 하우징내에삽입합니다 ( 그림 6 참조 ). 필터는쉽게제자리에 장착됩니다. 다음은필터하우징캡을돌려서잠그십시오 ( 그림 7 참조 ). 그림 5 그림 6 그림 7 EN 중요참고사항 : 필터를하우징에설치하기전에찬물로완전히헹구십시오. 그러면애완동물에해롭지는않지만겉에뭍은숯먼지가제거됩니다. 필터를사용하는동안소량의숯먼지가서서히떨어져나올수있습니다. 이것은정상이며애완동물에해가되지않습니다. 최상의성능을위해서는필터를두주마다교체해야합니다. 분수대를사용하는애완동물의수에따라필터를더자주교체해야할수도있습니다. 21

22 EN 8. 필터하우징의측면홈들을콘구멍의내부홈들과정렬시키십시오. 필터하우징은쉽게제자리에장착되어야합니다. 하우징을오른쪽으로 ( 시계방향 ) 사분의일회전하여제자리에잠기게하십시오. ( 그림 8) 9. 개인의취향이나애완동물의취향에따라다섯개의교환사용가능한주둥이링중에서하나를선택하십시오. 선택한주둥이링을필터하우징캡의상단에놓고부드럽게골고루내리눌러제자리에고정하십시오. ( 그림 9) 10. 유량제어캡을필터하우징캡상의돌기된홈과정렬시키십시오 ( 그림 10). 부드럽게내리눌러서캡이제자리에고정되게하십시오. 유량제어캡으로물의흐름강도를쉽게조절할수있습니다. 유량을늘리려면캡을오른쪽으로돌리고줄이려면왼쪽으로돌리십시오. 중요참고사항 : 유량제어캡을최대유량으로돌려도해결되지않는유량감소가발생하는경우, 막히고더러운필터의징조이거나필터하우징을헹구고닦을필요성을나타내는것일수있습니다. 분수대청소및유지관리에대한자세한내용은본안내서의 분수대분해및청소 항을참조하십시오. 11. 분수대를원하는위치에놓으십시오. 중요 : 바닥보호를위해항상타월이나플레이스매트같은보호매트를사용하십시오. 그러면애완동물이분수대를사용하면서튀는물로부터바닥을보호하는데도움이됩니다. 12. 분수대용기을물로채우십시오. 수위가최소한 MIN( 최저 ) 채우기선이상이되게하여펌프가물없는상태에서작동되지않게해야합니다. 그러면펌프작동에필요한물이공급됩니다. 분수대를 MAX( 최대 ) 채우기선이상으로채우지마십시오. 13. 분수대의전기플러그를꽂기전에전기코드와손이젖지않았는지확인하십시오. 분수대의플러그를일반콘센트에꽂으십시오. 14. 필요한만큼물을추가하십시오. 절대로수위가 MIN ( 최저 ) 채우기선 ( 용기바닥으로부터약 25 mm 위, 그림 11) 아래로내려가지않게해야하며그렇지않으면펌프가고장날수있습니다. 중요 : 절대로가득찬분수대를콘부품을잡아서들어올리지마십시오. 펌프를올바로들어올리기위해두손을사용해서분수대용기의측벽을잡아서올리십시오. 홈 높은홈 그림 8 요철부그림 9 그림 10 그림

23 분수대분해및청소 중요 : 분수대는청소를해야계속정상적으로작동합니다. 필터시스템애완동물분수대에는정기적으로교체해야하는두종류의필터가구비되어있습니다. 숯필터는나쁜맛과악취를제거하여물을신선하게유지합니다. 포움필터는털, 오물및애완동물사료를걸러서펌프로가지않게하는적합한여과기능을제공합니다. 이필터들은함께펌프를깨끗하게유지하고애완동물에게더욱신선한물을제공하는역할을합니다. 숯필터 : 필터들은 2-4 주마다교체해야합니다. 애완동물분수대를여러애완동물이사용하거나침을많이분비하는애완동물들이사용하는경우필터를더자주교체하십시오. 포움필터 : 애완동물분수대의위치와그것을사용하는애완동물의수에따라포움필터는 1-2 개월마다교체해야합니다. 청소할때필터를교체하지않는경우에는포움필터를깨끗한물로철저하게헹구어야합니다. 필터는애완동물분수대의추가기능입니다. 정상적인작동을위해필터사용이요구되지는않습니다. 그러나필터는올바로사용하고정기적으로교체할경우물을더욱깨끗하고신선하게유지하며애완동물분수대의수명을연장하는데도움이됩니다. 애완동물분수대를청소할때필터를물에헹굴수있습니다. 중요 : 비누잔류물은필터에스며들어제거할수없게될수있으므로절대로필터를비눗물로씻지마십시오. 필터는물로만헹구십시오. 분수대 : 매주한번씩청소하십시오. 1. 분수대의플러그를전원에서빼고인라인플러그의연결을해제하십시오 ( 그림 1 참조 ). 2. 유량조절캡과주둥이링을빼내십시오. 3. 필터하우징을반시계방향으로잠금해제위치로돌려서필터하우징을분리하십시오. 똑바로들어올려서옆에놓으십시오. 4. 분수대의물을비우십시오. 5. 일단분수대가비워지면반시계방향으로돌려서탭을잠금해제하여콘을분리하십시오. 들어올려서옆에놓으십시오 ( 그림 2 참조 ). 6. 다음은용기을거꾸로돌려서전기코드를두개의코드클립에서빼내십시오 ( 그림 12 참조 ). 그러면용기내의전기코드통과로를통해코드를당겨낼수있습니다 ( 그림 13 참조 ). EN 그림 12 코드통과로그림 13 코드클립 23

24 EN 7. 청소를위해펌프를빼내십시오. 먼저흡입관홀더를들어올려서흡입관을펌프로부터분리하여흡입관을떼어내십시오. ( 그림 14 및 15 참조 ) 그러면펌프를분리할수있습니다. 그런다음흡입관을흡입관홀더로부터당겨낼수있습니다. ( 자세한모터 / 펌프청소지침에대해서는 " 폄프유지보수 " 를참조하십시오 ) 그림 14 그림 펌프에서포움필터를제거하십시오. 펌프의전면판에축적되어있을수있는털, 오물또는애완동물사료를닦아내십시오 ( 자세한펌프청소법에대해서는 폄프유지보수 를참조하십시오 ). 9. 분수대부품을온수와비누로닦으십시오. 또한분수대를식기세척기의맨위선반에놓아도됩니다. 분수대를식기세척기에넣기전에펌프를빼내십시오. 펌프는식기세척기에넣지마십시오! 가능하면식기세척기내의수온을낮추도록권장합니다. 10. 어떤부분이나비좁은귀퉁이에손이미치기에어려움이있는경우, 면봉을사용해보거나 Drinkwell 청소키트 ( 브러시 3개키트 ) 를구입하십시오. 청소키를구입하기위해서는저희웹사이트 을방문하여가까운소매점을찾거나해당지역의고객지원센터전화번호를찾아보십시오. 폄프유지보수 중요 : 펌프청소는물의청결뿐만아니라분수대의장기사용을위해필수적입니다. 펌프를최소한두주마다청소하십시오. 펌프를정기적으로청소하지않으면품질보증이무효화될수있습니다. 흡입판 전면판 펌프 임펠러 24

25 1. " 분수대분해및청소 " 항 ( 구체적으로단계 6 및 7) 에설명된대로분수대에서펌프를빼내십시오. 2. 일단펌프가분수대에서이탈되면엄지와검지로전면판의한측면을가볍게압축하여빼내십시오. 손톱을전면판의경계선에집어넣어서젓혀내야할수도있습니다. 3. 다음은눈물방울모양의흡입판의좁은쪽에위치에있는작은입술모양부분아래로손톱을집어넣어흡입판을빼낼수있습니다 ( 그림 16). EN 흡입판당김탭 그림 흡입판을빼낸다음에는자력에의해고정되어있는임펠러 (3개의그림 17 흰색날이있는프로펠러 ) 를뺄수있습니다. 임펠러를빼내려면손톱을플라스틱날아래에넣고올려서빼내면됩니다 ( 그림 17). 5. 일단모터가분해되면부품들을따뜻한비눗물로씻으면됩니다. 면봉이나 Drinkwell 청소키트의 " 모터브러시 " 를사용하여모터설치자리에있는침적물을제거합니다 ( 그림 18). 추가로소독하고그림 18 경수물때를제거하려면흰식초 20% 와물 80% 를혼합한용액으로모터를닦으십시오. 맹물로철저하게헹구어야합니다. 6. 부품들이깨끗해졌으면사용을위해펌프를다시조립할수있습니다. a) 임펠러를설치합니다 b) 흡입판을설치합니다. c) 전면판을설치합니다. 25

26 EN 분수대재조립 1. 포움필터가펌프를둘러싸게하십시오. 전기코드는포움필터의아래쪽이아니라위로지나가야하는데이렇게함으로써포움필터가제자리에유지되기때문입니다. 2. 포움필터가펌프주변을단단히둘러싼상태에서용기중앙에있는네개의 12.5 mm 기둥사이의제위치에펌프를설치합니다. 펌프상단에있는구멍을용기내의전기코드통과로옆에배치해야합니다. 부드럽게내리눌러흡입컵들이맞물리게하십시오. 3. 흡입관을흡입관홀더안에설치한후에기둥상의안내선을흡입관홀더내의홈과정렬하여흡입관홀더를다시전기코드통과로기둥에설치하십시오. 흡입관정렬에유의하여펌프상단에있는구멍안에맞게해야합니다. 4. 인라인플러그를펌프옆에있는구멍안으로끼워넣으십시오. 용기의바닥쪽에서 " 코드클립 " 을사용하여코드를제자리에고정하십시오 ( 그림 12). 다음은전기코드를코드통과로를통해분수대밖으로직접끌어내십시오 ( 그림 12 및 13). 이통과로를이용하여전기코드가보이지않게하십시오. 5. 콘주변의세홈들을용기내의해당탭들과정렬시키십시오. 다음은콘부품을오른쪽으로 ( 시계방향 ) 돌려서탭들이제자리에잠기게하십시오. ( 그림 2 및 4) 6. 분수대를청소한후에, 필터를교체하면좋습니다. 7. 필터하우징캡을돌려서끼우고필터하우징을콘의상단에있는구멍내의제자리에밀어넣으십시오. 필터하우징을오른쪽으로 ( 시계방향 ) 사분의일회전하여제자리에잠기게하십시오. 8. 선호하는주둥이링을선택하여 ( 주둥이 1개에서 5개까지 ) 필터하우징캡꼭대기에놓고부드럽게눌러서제자리에들어가게합니다. 사방으로끝까지고르게눌러내려야합니다. 9. 흐름제어캡이필터하우징캡상의홈과정렬되게하고부드럽게내리눌러서흐름제어캡을설치하십시오. 10. 분수대를원하는위치에놓고 MAX( 최대 ) 채우기선까지물로채우십시오. 11. 마른손으로인라인플러그를다시연결한후에분수대의플러그를꽂으십시오. 유량을원하는대로조절해서애완동물이분수대의신선한자유낙하수를즐기게하십시오. 26

27 애완동물분수대와환경 습한환경에거주하며곰팡이나조류문제가있는경우, 정기적인세척후모든애완동물분수대부품들을희석한식초표백제용액 ( 백식초 20% 및물 80%) 에 10분정도담그십시오. 그런다음, 희석한식초표백제를모터설치공간에따르십시오. 사용하는물이 경수 인경우펌프내외에소량의흰색광물침전물이생길수있습니다. 이로인해결국에는임펠러가올바로회전되지못할수있습니다. 펌프교체및손상을방지하려면다음예방책을숙지하십시오. 1. 더자주펌프를청소합니다. 2. 매주희석한식초표백제로펌프를세척합니다. 3. 수돗물대신에병입수를사용합니다. EN 사용요령 분수대를처음접할때애완동물은새롭고전에보지못한이물체를경계할수있습니다. 분수대를사용하기시작한후에애완동물이스스로자신의페이스에따라적응하게하십시오. 어떤애완동물은며칠이지난후에사용하기시작할수도있고, 어떤애완동물은즉시사용하기시작할수도있습니다. 애완동물은분수대가그들의정상적인식사공간에서멀리떨어져있기를원할수도있습니다. 주방의다른부분이나화장실이나다용도실과같은다른장소에놔두어보십시오. 산뜻하고차거운물을공급하기위해서는용기에얼음을넣으십시오! 27

28 EN 품질보증및고객서비스 본제품은제조업체로부터 1년동안제한적인보증이제공됩니다. 본품질보증은사고, 오용및남용으로인한손상을보상하지않습니다. 법적으로허용되는대로부수적또는결과적피해도명시적으로제외합니다. 청소부실, 오물또는 " 경수 " 로인한광물질침전의결과로발생하는기능상실은본보증의대상이되지않습니다 ( 청소지침및환경유의사항을참조하십시오 ). 본제품의보증및사용약관에대한상세한안내는 에서보시거나다음주소로이메일을보내어제공받으실수있습니다 : asiacc@petsafe.net. 설치및기술적인문제가있거나필요한경우제품교체를위한도움을받기위해서는해당지역고객서비스센터에문의하십시오. 해당지역의고객관리센터목록은당사웹사이트 에나와있습니다. 준수 본기기는 EMC 및저전압지침을준수합니다. Radio Systems Corporation에서승인하지않은본제품에대한무단변경이나개조는유럽연합규정의위반에해당되고기기작동에대한사용자의권한및보증을무효화할수있습니다. 적합성선언은다음사이트에서보실수있습니다 : 중요한재활용정보 해당국가의폐가전제품규정을준수하십시오. 이기기는재활용해야합니다. 이기기가더이상필요하지않아폐기할경우일반생활폐기물로폐기해서는안됩니다. 당사의재활용시스템을이용하려면구입한곳으로반환해주십시오. 반환이어려운경우에는고객관리센터에문의하여자세한정보를얻으십시오. 28

29 사용조건과배상책임의한계 1. 사용조건이제품을사용하려면본설명서에포함된약관, 조건및통지를변경하지않고수용해야합니다. 본제품의사용은당해의모든조항, 조건및통지를수용하는것으로간주됩니다. 이러한약관, 조건및통지를수락하지않는경우에는비용및위험을부담하고제품을사용하지않은채로원래의포장에넣어구입증거물과함께고객관리센터로반송하여환불을요청하십시오. 2. 올바른사용본제품이귀하의애완견에적합한지잘모를경우에는사용전에수의사또는공인트레이너에게문의하십시오. 적절한사용에는사용설명서의전체내용및일체의구체적안전정보내용을검토하는것이포함되나이에국한되지는않습니다. 3. 불법적또는용도이외의사용금지본제품은애완동물에게만사용하도록제작되었습니다. 용도이외의방식으로이제품을사용하는것은연방, 주, 지역법률에위배될수있습니다. 4. 배상책임의한계 Radio Systems Corporation이나모든관련기업은어떠한경우에도 (i) 간접적, 징벌적, 부수적, 결과적이거나특별한손해및 / 또는 (ii) 이제품의오용으로인하거나그와관련하여발생하는모든손실이나손해에대해서도책임을지지않습니다. 구매자는법이허용하는최대한도내에서이제품의사용으로인한모든위험및책임을집니다. 의문의여지를피히기위하여, 이조항 4의어떠한내용도인명사망이나상해또는사기나사기성의잘못된설명에대한 Radio Systems Corporation의책임을제한하지않습니다. 5. 구매조건변경 Radio Systems Corporation은이제품에적용되는약관, 조건및통지를수시로변경할수있는권리를보유합니다. 이제품을사용하기전에그러한변경사항이통지되었을경우에는본설명서에설명되어있는것처럼구속력을갖게됩니다. EN 해당특허 : 미국특허번호 5,799,609 및 5,842,

30 30

31 31

32 Radio Systems Corporation PetSafe Way Knoxville, TN (865) Radio Systems Corporation