< 좌측면 > Left Side image < 정면 > Front Side image

Size: px

Start display at page:

Download "< 좌측면 > Left Side image < 정면 > Front Side image"

일화 성
5 years ago
Views:

1 기능시험평가지 Task Instructions for Skills Test 업종 평가시간 Test Duration: 5 분 5minutes Ⅰ. 과제의구성 Test Procedure 구분 Procedure Test Test Test 3 세부과제명 Test 핀꽂기 Insert Pins 작업물걸기 Hang Items 평가시간 Test Duration 비고 Remark min - min - 3 min 전동공구를사용시 분으로조정 When it comes to electrically driven tools, the time will be adjust into min. Ⅱ. 요구사항및도면 Requirements and Diagram Test. 핀꽂기 Insert Pins. 요구사항 Requirements 도면에따라주어진작업판에지급된핀을색상, 모양, 크기에맞게꽂으십시오. Considering the diagram, insert the pins in to the slate provided according to the color, size and shape.. 도면 diagram [ 핀꽂이판 Pin Board : Size : 380 x 380mm ]

2 < 좌측면 > Left Side image < 정면 > Front Side image

3 Test. 작업물걸기 Hang Items. 요구사항 Requirements 작업물걸이대에지급된링을규격에맞게거십시오. Hang the rings on the rod according to size.. 도면 diagram [ 작업물걸이대 Ring Rod : 링 ring 50mm ] < 링걸이대 > < 링 > 3

4 < 작업예시 > Test 3. join. 요구사항 Requirements 지급된공구와부품을이용해정해진위치에합판을정확하게결속하여이어붙이고 감독위원의지시에따라해체하시오. Bind and stick the plywood to the indicated joint position accurately by using designated tools and parts and dismantle it in accordance with the instructor s instructions. 4

5 . 도면 diagram < 실시요령 > Instructions. 안전장갑을착용하고준비된경첩을못의위치와수에유의하여제한시간내에제시된 도면과같이지정된위치에경첩을부착하시오. Attach the hinge to the indicated position as in the presented design in a limited time by wearing safety gloves and being careful of the position and number of nails.. 나무판과나무판사이를 mm 떼고경첩을부착해야합니다. Please link the hinge and the plates, considering the mm gap between the plates. 3. 경첩을체결한후나무판을접었을때접히지않으면최하점을부여하니유의하십시오. Please be conscious of the fact that you will be given the lowest point if the plates couldn t be folded after linking the hinge. 4. 감독위원의지시에따라분리해체하시오. Disassemble and separate the unit in accordance with the instructor s directions. 5. 조립은하였으나일치성치수가 0mm 이상차이나는경우최하점을부여하니유의하십시오. Be aware of the fact that you will be given the lowest point if the corresponding scale is more than 0mm. 5

< 작업예시 > example < 접었을때단면 > when folded Ⅲ. 응시자유의사항 Guideline for Applicants. 작업중안전사고가나지않도록유의하십시오.

시작전에 미리작업을하거나, 종료후에도계속작업을할경우최하점수를부여하니유의하십시오. Follow the instructor s signal to begin and end each session.

감독위원이시험종료를선언하면수험자는즉시작업을중단하고채점이끝날때까지 대기하십시오. 채점이끝나면다음수험자를위하여평가도구를처음상태로원위치하십시오. ( 체결한나사못은분리해체하시오.

6 < 작업예시 > example < 접었을때단면 > when folded Ⅲ. 응시자유의사항 Guideline for Applicants. 작업중안전사고가나지않도록유의하십시오. Take extra care to prevent any accidents.. 모든작업은감독위원의시작선언과함께시작하고종료선언과함께종료하십시오. 시작전에 미리작업을하거나, 종료후에도계속작업을할경우최하점수를부여하니유의하십시오. Follow the instructor s signal to begin and end each session. If you perform the job before the test starts or after it ends, you will receive the lowest mark. 3. 감독위원이시험종료를선언하면수험자는즉시작업을중단하고채점이끝날때까지 대기하십시오. 채점이끝나면다음수험자를위하여평가도구를처음상태로원위치하십시오. ( 체결한나사못은분리해체하시오.) At the instructor s signal to end the session, stop the job immediately and wait until your work is evaluated. After evaluation, return all testing tools to their original position for next applicants. (Disassemble and separate the joined screws.) 6

7 4. 각각의작업은가능한빠르고정확하게작업하고, 작업이끝난응시자는바로손을들어 감독위원에게확인을받으십시오. Complete each task as quickly and precisely as possible. After completing a task, please raise your hand to inform the examiner of it. 5. 작업은신속하고정확하게수행하되, 무리하게힘을가하거나불필요한동작으로평가도구가 훼손될경우최하점수를부여하니유의하십시오. Perform the job promptly and accurately. Damaging testing tools using unnecessary force or action will result in the lowest mark. 6. 감독위원의지시에불응하거나, 수험질서를어지럽히는경우퇴실조치되오니유의하십시오. If you fail to follow instructions or cause disorder, you may get expelled from the testing room. 7. 과제는작업수행시반드시안전장갑을착용하도록하며, 체결공구를정확한방법으로 사용하여안전사고가발생하지않도록주의하십시오. Make sure to wear safety gloves when carrying out the work and be careful not to cause a safety accident by using units diagonally in an inappropriate posture. 8. 안전사고가발생하면해당과제는최하점을부여하므로유의하십시오. Be aware of the fact that you will be given the lowest point if there has been negligent accident. 7

8 Ⅴ. 평가장시설목록 List of Test Facilities 구분 Type 일련번호 Serial No. 장비및시설명 Equipment & Facilities 규격 Spec. 단위 Unit 수량 QTY 비고 Remarks 과제 Test 작업대 Workbench,400x,000x700mm // 핀꽂이세트 Pin Set 제작 manufacture 셋 SET 핀 : 36 Pin : 36 pcs 핀박스 Pin Box 핀꽂이판 Pin Board // 3 스톱워치 Stop Watch 연속형공업표준 industrial standard 과제 Test 4 작업대 Workbench,400x000x700mm // 5 걸이대세트 Rod Set 제작 manufacture 셋 SET 링 36 (3 종 ) 36 rings (3 types) // 6 스톱워치 Stop Watch 연속형공업표준 industrial standard 3 과제 Test3 7 작업대 Workbench,400x,000x700mm // 8 // 9 // 0 합판 Plywood 나사못 Screw 드라이버 Driver 50*50*8 3-5mm 십자드라이버 (300mm 미만 ) Phillips screwdriver (less than 300mm) 장 Sheet 0 8T(MDF*) Medium Density Fiberboard 4명당 장 sheet for 4 people 3-5mm 인당 8 8pcs for people 5 인당 pcs for 5people // 경첩 Hinge 3" // 안전장갑 Safety globe 장 Sheet 인당 pcs for people 8

기능시험평가지 Task Instructions for Skills Test 업종 Job Category 어업 Fishery 세부분야 Subject 연근해어업 In and off-shore fishery 평가시간 Test Duration: 4 분, 4min Ⅰ. 과제의구

기능시험평가지 Task Instructions for Skills Test 연근해 평가시간 Test Duration: 4 분, 4min Ⅰ. 과제의구성 Test Procedure 구분 Procedure 과제 Test 2과제 Test 2 3 과제 Test 3 세부과제명 Test 수작업핀꽂기 Insert Pins Manually 작업물운반 Transporting