SamHwa Engineering 2003-10-14 MM440 사용설명서 SamHwa Engineering Tel. +82 2 895 5816,5826 Fax. +82 2 6336 5816 http://www.samhwasiemens.co.kr MM440_ 사용설명서 1 By H.J.Kim
SamHwa Engineering 2003-10-14 1. 개요 1.1 MM440 - MM440은 3상모터의속도를제어하기위한인버터이다. 모델범위는단상 120W ~ 삼상 200kW까지이다. - 마이크로프로세서로제어되며 IGBT를사용, 다양하고신뢰할수있는성능을발휘한다. 선택가능한스위칭주파수와펄스폭변조방법은조용한모터의운전을가능하게한다. - 공장설정값혹은파라메터를이용, 다양한범위의기계응용에사용가능하다. 1.2 MM440 특성 1.2.1 일반 - 운전, 파라메터설정, 설치가용이하다. - 제어신호의빠른응답시간. - 다양한기계응용을위한폭넓은파라메터설정. - 간단한케이블연결및다양한옵션. - 저소음을위한높은스위칭주파수. - PC 통신, BOP, AOP, Profibus Module용외부옵션. 1.2.2 성능 - 향상된동적특성과자속전류제어 (Flux Current Control) - SVC(Sensor-less Vector) Control - VC(Vector) Control --Option 첨부시 - 빠른전류제한. - DC 인가제동내장. - 회생에너지소멸용 Braking Chopper 내장. - 제동성능향상을위한컴파운드제동. - S형가, 감속시간설정가능. - PID제어기능을이용한폐회로제어기능. 1.2.3 보호 - 인버터, 모터의완벽한보호. - 과전압, 저전압보호. - 인버터과열보호. - 모터과열 (I2t) 보호. - 접지불량폴트기능. - 단선보호. MM440_ 사용설명서 2 By H.J.Kim
SamHwa Engineering 2003-10-14 2. 제품사양 구분사양 주운전전압 200~240V ±10% 1AC 200~240V ±10% 3AC 380~480V ±10% 3AC 출력범위 200~240V ±10% 1AC 0.12kW ~ 3.0kW 200~240V ±10% 3AC 0.12kW ~ 45kW 380~480V ±10% 3AC 0.37kW ~ 200kW 제품크기 Flame A B C D E F FX GX WxHxD 73x173 149x202 185x245 275x520 275x650 350x850 330x1555 330x1875 (mm) x149 x172 x195 x245 x245 x320 x360 x560 보호등급 IP20 사용온도 CT : -10 ~ +50, VT : -10 ~ +40 보관온도 -40 ~ +70 습도 95% 운전고도 해발 1,000 m 까지 ( 감쇠없음 ) 제어모드 벡터제어, 토르크제어 ( 선형 V/F, 비선형 V/F), 자속전류제어 (Flux Current Control) 과부하수용력출력전류의 150%(60 초 ), 200%(3 초 ) 전자파수용력옵션 EMC Filter ( ClassA or ClassB ) 보호기능 입력주파수 주파수분해능력 저전압, 과전압, 접지불량, 단선, 인버터과열, 모터과열, 스톨방지 47 ~ 63Hz 디지털 0.01Hz, 직렬 0.01Hz, 아날로그 10bit 스위칭주파수 2k ~ 16k Hz ( 2k Hz 씩변화가능 ) 디지털입력 6 단자 ( PNP/NPN 선택가능 ) 다단주파수 16 단 ( binary code 사용 ) 점프주파수 4 개 릴레이출력 3 개 ( 30V dc 5A / 250V ac 2A ) 아날로그입력 아날로그출력 2 개 ( 0/2V ~ 10V or -10V~+10V or 0/2mA~20mA ) : 사용자지정가능 2 개 ( 0/2mA ~ 20mA ) : 사용자지정가능 직렬인터페이스 옵션 ( RS232, RS485 ) 디자인 ISO9001 규격 UL, cul, CE, C-tick CE 마크 EC 저전압규정 73/23/EEC, 전자파규정 89/336/EEC 규격에합격 출력역률 0.7 인버터효율 96% ~ 97% 침입전류 제동기능 정격전류보다적다 제동초퍼내장, DC 인가제동, 컴파운드제동 MM440_ 사용설명서 3 By H.J.Kim
General Circuit Diagram Ω Ω Ω 3.Circuit Diagrams
SamHwa Engineering 2003-10-14 4. 파라메터설정 4.1 파라메터설정입문 4.1.1 기본설정 Parameter - P0003 : 사용자사용레벨 ( 출하시설정값 : 1 ) 파라메터사용값을나타낸다. 대부분의간단한응용에서는기본사용설정만으로도충분히사용가능하다. 설정가능한값 0 : 사용자정의파라메터목록 P0013의설명참고. 1 : 기본 : 가장자주이용하는파라메터에접근가능. 2 : 확장 : 확장된 I/O 기능활용이가능. 3 : 전문 : 전문사용자만사용가능. 4 : 서비스 : 서비스전문가만사용가능패스워드로보호 - P0004 : 파라메터필터링기능 ( 출하시설정값 : 0 ) 이파라메터에서선택한파라메터만인버터에표시된다. 예를들면, P0004=22에설정하였다면 PI 제어와관련된파라메터만표시된다. 설정가능한값 0 : 모든파라메터 2 : 인버터 3 : 모터 7 : 명령 & 디지털입출력 8 : 아날로그입출력 10 : 설정채널 & 가감속발생기 12 : 드라이브특성 13 : 모터제어 20 : 통신 21 : 알람, 경고 & 모니터링 22 : PI 제어기참고 P0004의설정값에관계없이인버터를운전할수있다. 일부파라메터는 Commissioning only 파라메터이고, 필터파라메터내에서만볼수있다. 그러나, 이파라메터들을 P0010=1 로설정해야지만변경가능하다. 이파라메터들은오른쪽컬럼에기호를보고알수있다.( 열쇠그림 ) - P0005 : Display 표시선택 ( 출하시설정값 : 21 ) 20 : 설정주파수 21 : 실제주파수 22 : 출력rpm 24 : 출력주파수 25 : 출력전압 26 : DC Link 전압 27 : 출력전류 34 : 모터온도 37 : 인버터온도 39 : 소비전력 MM440_ 사용설명서 5 By H.J.Kim
SamHwa Engineering 2003-10-14 - P0010 : 파라메터필터링기능 ( 출하시설정값 : 0 ) 0 : 운전준비 1 : 빠른운전수행 ( 열쇠그림있는파라메터설정값변경시 ) 30 : 공장설정치로리셋 ( P3900=1 ) 주 ) 인버터가운전하기전반드시 0 으로설정하여야운전된다. - P0304 : 모터정격전압 ( 출하시설정값 :? V ) at P0010=1 - P0305 : 모터정격전류 ( 출하시설정값 :? A ) at P0010=1 - P0307 : 모터정격용량 ( 출하시설정값 :? kw ) at P0010=1 - P0310 : 모터정격주파수 ( 출하시설정값 : 50 Hz ) at P0010=1 - P0311 : 모터정격rpm ( 출하시설정값 :? rpm ) at P0010=1 - P3900 : 최종빠른운전수행 : 3 ( 모든입력 data에의해연산수행,at P0010=1 ) ( 주 ) P3900=3을수행하면자동으로연산을마친후에 P0010=0으로전환된다. - P1080 : 모터최소주파수 ( 출하시설정값 : 0.0 Hz ) 0.0 ~ 650.0 Hz - P1082 : 모터최대주파수 ( 출하시설정값 : 50.0 Hz ) 0.0 ~ 650.0 Hz - P1120 : 모터가속시간 ( 출하시설정값 : 10.0 sec ) 0.0 ~ 650.0 Hz - P1121 : 모터감속시간 ( 출하시설정값 : 10.0 sec ) 0.0 ~ 650.0 Hz - P1300 : 출력사양선택 ( 출하시설정값 : 1 ) 0 : v/f 직선 1 : FCC ( Flux current control ) 2 : 비선형 v/f 3 : 다중 v/f ( 전문가 only ) 20 : Sensorless-Vector Control 21 : Vector Control with sensor 22 : Sensorless-Vector torque Control - P0700 : 명령경로선택 ( 출하시설정값 : 0 ) 0 : 공장설정치 1 : 키패드 ( BOP / AOP ) 2 : Terminal ( 단자대 ) 4 : BOP 링크의 USS1 ( RS232 ) 5 : 통신링크의 USS2 ( RS485 ) 6 : Profibus/ 통신링크의필드버스 MM440_ 사용설명서 6 By H.J.Kim
SamHwa Engineering 2003-10-14 4.1.2 아날로그설정운전.. 기본조건 - 외부 VR, 외부전압 (0~10V), 외부전류 (0<4>~20mA) 을이용하여속도조절. - 외부조작스위치 ( 또는 PLC) 를이용하여모터구동 ( 정, 역운전 ). - Inverter 내부 Terminal을사용 Inverter 운영.. 적용 Inverter 선정 - 적용모터의정격용량, 정격전류, 정격전압에맞는모델선정. 주 ) 원하는 Application에적당한모델인지충분히검토요망. Ex. Digital input, analogue output, relay output etc.. Inverter Setting 1) 일반적설정 ( 공장설정값 ) - 기본공장설정값은위의기본조건과규합되나, 사용지역의설정이유럽 (50Hz) 으로되어있으므로사용지역또는적용모터가국산 (60Hz용) 인경우 Dip switch2를 On 상태로하여주거나세부설정의모터데이터를명판내용대로정확히기입하면된다. 2) 세부적설정 - 44MM~ Inverter에는 2개의 Analogue Input이있으며, 일반적으로 Input1을사용하나, 선택적으로 Input1 or Input2를사용할수있으며설정범위를조정할수있다. - 적용모터의 Data 및 User's Application에알맞은 Parameter setting이가능하다. MM440_ 사용설명서 7 By H.J.Kim
SamHwa Engineering 2003-10-14 4.1.2.1 Parameter Setting.( 속도조절 : 전압 control ) - P0003 : 사용자사용레벨 : 2 ( 확장 ) - P0004 : 파라메터필터링기능 : 0 ( All parameter ) - P0700 : 명령경로선택 : 2 ( Terminal ) - P1000 : 주파수 Main 설정 : 2 ( 아날로그입력 ) - P0304 : 모터정격전압 :? V ( at P0010=1 일때수치변경가능 ) - P0305 : 모터정격전류 :? A ( at P0010=1 일때수치변경가능 ) - P0307 : 모터정격용량 :? kw ( at P0010=1 일때수치변경가능 ) - P0310 : 모터정격주파수 :? Hz ( at P0010=1 일때수치변경가능 ) - P0311 : 모터정격rpm :? rpm ( at P0010=1 일때수치변경가능 ) - P3900 : 최종빠른운전수행 : 3 ( 모든입력 data에의해연산수행,at P0010=1 ) ( 주 ) P3900=3을수행하면자동으로연산을마친후에 P0010=0으로전환된다. - P1080 : 모터최소주파수 :? Hz ( 0.0 ~ 650.0 Hz ) - P1082 : 모터최대주파수 :? Hz ( 0.0 ~ 650.0 Hz ) - P1120 : 모터가속시간 :? sec ( 0.0 ~ 650.0 Hz ) - P1121 : 모터감속시간 :? sec ( 0.0 ~ 650.0 Hz ) - P0756.0 : 아날로그입력종류선택 : 0 ( 0~10V ) ( 주 ) 전면 Dip1( 좌측 ) off 상태유지. - P0757.0 : 아날로그입력범위 X1(Min.) : 0.0 V - P0758.0 : 아날로그입력범위 Y1(Min.) : 0.0 % ( -99999.9 ~ +99999.9 ) - P0759.0 : 아날로그입력범위 X2(Max.) : 10 V - P0760.0 : 아날로그입력범위 Y2(Max.) : 100 % ( -99999.9 ~ +99999.9 ) ( 주 ) P0758 & P0760 의기준값 (%) : P2000 ( Reference Freq. ) - P0776.0 : 아날로그출력종류선택 : 0 ( 전류출력 ) - P0777.0 : 아날로그출력범위 X1(Min.) : 0 % (-99999.0 ~ +99999.0 ) - P0778.0 : 아날로그출력범위 Y1(Min.) : 0<4> ma ( 0 ~ 20 ma ) - P0779.0 : 아날로그출력범위 X2(Max.) : 100 % ( -99999.0 ~ +99999.0 ) - P0780.0 : 아날로그출력범위 Y2(Max.) : 20 ma ( 0 ~ 20 ma ) - P1300 : 출력사양선택 : 1 ( FCC ) - P0005 : Display 표시선택 : 21 ( 실제주파수 ) MM440_ 사용설명서 8 By H.J.Kim
SamHwa Engineering 2003-10-14 4.1.2.2 Parameter Setting.( 속도조절 : 전류 control ) - P0003 : 사용자사용레벨 : 2 ( 확장 ) - P0004 : 파라메터필터링기능 : 0 ( All parameter ) - P0700 : 명령경로선택 : 2 ( Terminal ) - P1000 : 주파수 Main 설정 : 2 ( 아날로그입력 ) - P0304 : 모터정격전압 :? V ( at P0010=1 일때수치변경가능 ) - P0305 : 모터정격전류 :? A ( at P0010=1 일때수치변경가능 ) - P0307 : 모터정격용량 :? kw ( at P0010=1 일때수치변경가능 ) - P0310 : 모터정격주파수 :? Hz ( at P0010=1 일때수치변경가능 ) - P0311 : 모터정격rpm :? rpm ( at P0010=1 일때수치변경가능 ) - P3900 : 최종빠른운전수행 : 3 ( 모든입력 data에의해연산수행,at P0010=1 ) ( 주 ) P3900=3을수행하면자동으로연산을마친후에 P0010=0으로전환된다. - P1080 : 모터최소주파수 :? Hz ( 0.0 ~ 650.0 Hz ) - P1082 : 모터최대주파수 :? Hz ( 0.0 ~ 650.0 Hz ) - P1120 : 모터가속시간 :? sec ( 0.0 ~ 650.0 Hz ) - P1121 : 모터감속시간 :? sec ( 0.0 ~ 650.0 Hz ) - P0756.0 : 아날로그입력종류선택 : 2 ( 0<4>~20 ma ) ( 주 ) 전면 Dip1( 좌측 ) On 상태유지. - P0757.0 : 아날로그입력범위 X1(Min.) : 0<4> ma - P0758.0 : 아날로그입력범위 Y1(Min.) : 0.0 % ( -99999.9 ~ +99999.9 ) - P0759.0 : 아날로그입력범위 X2(Max.) : 20 ma - P0760.0 : 아날로그입력범위 Y2(Max.) : 100 % ( -99999.9 ~ +99999.9 ) ( 주 ) P0758 & P0760 의기준값 (%) : P2000 ( Reference Freq. ) - P0776.0 : 아날로그출력종류선택 : 0 ( 전류출력 ) - P0777.0 : 아날로그출력범위 X1(Min.) : 0 % (-99999.0 ~ +99999.0 ) - P0778.0 : 아날로그출력범위 Y1(Min.) : 0<4> ma ( 0 ~ 20 ma ) - P0779.0 : 아날로그출력범위 X2(Max.) : 100 % ( -99999.0 ~ +99999.0 ) - P0780.0 : 아날로그출력범위 Y2(Max.) : 20 ma ( 0 ~ 20 ma ) - P1300 : 출력사양선택 : 1 ( FCC ) - P0005 : Display 표시선택 : 21 ( 실제주파수 ) MM440_ 사용설명서 9 By H.J.Kim
SamHwa Engineering 2003-10-14 4.1.2.3 배선및설치. - Analogue 입력및제어명령. < 전압입력시 > < 전류입력시 > MM440_ 사용설명서 10 By H.J.Kim
SamHwa Engineering 2003-10-14 - Analogue 출력. 주 ) 1. 인버터의아날로그출력범위는 0(4) ~ 20mA로정, 역방향을모두사용하는경우표시용계기의입력범위는 0(4) ~ 20mA or 0 ~ 10V 이어야하며, 표시출력범위는 0(4)mA(V) 시 -100%, 20(10)mA(V) 시 +100% 용으로선정하여야한다.( 출력방향 < 회전방향 > 에따른표시를위함 ) 2. 방향에상관없이아날로그출력 0(4)~20mA ( r0018>2.0 ) - P0003 = 3 ( 전문가모드 ) - P2800 = 1 ( 사용자정의선택사양사용 ) - P2802[8] = 1 ( 연산기능사용 ) - P2877[0] = 21 - P2877[1] = 21 - P2264 = 2878 - P2270 = 1 ( 연산수행 ) - P0771 =2272 ( 아날로그출력으로결과공급 ) 3. 2개의아날로그입력을사용하여선택형동작을요할시 ( 보편적으로자동 / 수동의조작시사용 ) - P0809[2] = 1 (copy CDS) - P0703[0] = 99 * - P0703[1] = 99 * - P1000[0] = 2 - P1000[1] = 7 - P0810 = 722.2 * ~ 상기예제는 Din3을절체용으로이용시이며, 다른 Din을사용시에는해당되는 Din용 Parameter와 P0810의값을변경시켜주면된다.(* 표 ) MM440_ 사용설명서 11 By H.J.Kim
SamHwa Engineering 2003-10-14 4.1.3 디지탈설정운전.. 기본조건 - BOP/AOP 운전. - 다단속운전1 (1~6속도가능 ). - 다단속운전2 (1~15속도가능 : Binary coded selection). - BOP/AOP or Inverter 내부 Terminal을사용 Inverter 운전.. 적용 Inverter 선정 - 적용모터의정격용량, 정격전류, 정격전압에맞는모델선정. 주 ) 원하는 Application에적당한모델인지충분히검토요망. Ex. Digital input, analogue output, relay output etc.. Inverter Setting 1) 일반적설정. - 사용지역의설정이유럽 (50Hz) 으로되어있으므로사용지역또는적용모터가국산 (60Hz용) 인경우 Dip switch2를 On 상태로하여주거나세부설정의모터데이터를명판내용대로정확히기입하면된다. 2) 세부적설정 - 적용모터의 Data 및 User's Application에알맞은 Parameter setting이가능하다. 4.1.3.1 BOP/AOP 운전시 Parameter Setting. - P0003 : 사용자사용레벨 : 2 ( 확장 ) - P0004 : 파라메터필터링기능 : 0 ( All parameter ) - P0700 : 명령경로선택 : 1 ( BOP/AOP <Keypad> ) - P1000 : 주파수 Main 설정 : 1 ( MOP< 운전속도 > setpoint ) - P0304 : 모터정격전압 :? V ( at P0010=1 일때수치변경가능 ) - P0305 : 모터정격전류 :? A ( at P0010=1 일때수치변경가능 ) - P0307 : 모터정격용량 :? kw ( at P0010=1 일때수치변경가능 ) - P0310 : 모터정격주파수 :? Hz ( at P0010=1 일때수치변경가능 ) - P0311 : 모터정격rpm :? rpm ( at P0010=1 일때수치변경가능 ) - P3900 : 최종빠른운전수행 : 3 ( 모든입력 data에의해연산수행,at P0010=1 ) ( 주 ) P3900=3을수행하면자동으로연산을마친후에 P0010=0으로전환된다. - P1080 : 모터최소주파수 :? Hz ( 0.0 ~ 650.0 Hz ) - P1082 : 모터최대주파수 :? Hz ( 0.0 ~ 650.0 Hz ) - P1120 : 모터가속시간 :? sec ( 0.0 ~ 650.0 Hz ) - P1121 : 모터감속시간 :? sec ( 0.0 ~ 650.0 Hz ) - P1040 : MOP( 운전속도 ) 설정값 :? Hz ( -650 ~ +650 Hz ) - P1300 : 출력사양선택 : 1 ( FCC ) - P0005 : Display 표시선택 : 21 ( 실제주파수 ) 주 ) 최종운행한주파수를기억하려면 P1031=1 로설정한다. ( Keypad 의최종설정값을 P1040 에자동 Up-data 한다. ) MM440_ 사용설명서 12 By H.J.Kim
SamHwa Engineering 2003-10-14 4.1.3.2 1~4속도운전시 Parameter Setting. - P0003 : 사용자사용레벨 : 2 ( 확장 ) - P0004 : 파라메터필터링기능 : 0 ( All parameter ) - P0304 : 모터정격전압 :? V ( at P0010=1 일때수치변경가능 ) - P0305 : 모터정격전류 :? A ( at P0010=1 일때수치변경가능 ) - P0307 : 모터정격용량 :? kw ( at P0010=1 일때수치변경가능 ) - P0310 : 모터정격주파수 :? Hz ( at P0010=1 일때수치변경가능 ) - P0311 : 모터정격rpm :? rpm ( at P0010=1 일때수치변경가능 ) - P3900 : 최종빠른운전수행 : 3 ( 모든입력 data에의해연산수행,at P0010=1 ) ( 주 ) P3900=3을수행하면자동으로연산을마친후에 P0010=0으로전환된다. - P1080 : 모터최소주파수 :? Hz ( 0.0 ~ 650.0 Hz ) - P1082 : 모터최대주파수 :? Hz ( 0.0 ~ 650.0 Hz ) - P1120 : 모터가속시간 :? sec ( 0.0 ~ 650.0 Hz ) - P1121 : 모터감속시간 :? sec ( 0.0 ~ 650.0 Hz ) - P0700 : 명령경로선택 : 2 ( Terminal ) - P0701 : 디지탈입력 1 : 1 ( 정방향운전 ) - P0702 : 디지탈입력 2 : 12 ( 반전 < 역회전 > 설정 ) - P0703 : 디지탈입력 3 : 15 ( 다단주파수3, P1003로속도설정 ) - P0704 : 디지탈입력 4 : 15 ( 다단주파수4, P1004로속도설정 ) - P0705 : 디지탈입력 5 : 15 ( 다단주파수5, P1005로속도설정 ) - P0706 : 디지탈입력 6 : 15 ( 다단주파수6, P1006로속도설정 ) - P1000 : 주파수 Main 설정 : 3 ( 다단주파수 ) - P1003 : 다단주파수3 (FF3) :? ( -650 ~ +650 Hz ) - P1004 : 다단주파수4 (FF4) :? ( -650 ~ +650 Hz ) - P1005 : 다단주파수5 (FF5) :? ( -650 ~ +650 Hz ) - P1006 : 다단주파수6 (FF6) :? ( -650 ~ +650 Hz ) - P1300 : 출력사양선택 : 1 ( FCC ) - P0005 : Display 표시선택 : 21 ( 실제주파수 ) MM440_ 사용설명서 13 By H.J.Kim
SamHwa Engineering 2003-10-14 주 ) 1. P0701,P0702,P0703,P0704,P0705,P0706=16 이면별도의 Run(On) 명령이없이운전가능하다.(6속운전) 2. Din3,Din4,Din5,Din6이모두 On이되면, 설정값 (P1003,P1004,P1005,P1006) 이모두합하여져서출력이되며단,P1082의값이상이될수없다. MM440_ 사용설명서 14 By H.J.Kim
SamHwa Engineering 2003-10-14 4.1.3.3 1~6속도운전시 Parameter Setting. - P0003 : 사용자사용레벨 : 2 ( 확장 ) - P0004 : 파라메터필터링기능 : 0 ( All parameter ) - P0304 : 모터정격전압 :? V ( at P0010=1 일때수치변경가능 ) - P0305 : 모터정격전류 :? A ( at P0010=1 일때수치변경가능 ) - P0307 : 모터정격용량 :? kw ( at P0010=1 일때수치변경가능 ) - P0310 : 모터정격주파수 :? Hz ( at P0010=1 일때수치변경가능 ) - P0311 : 모터정격rpm :? rpm ( at P0010=1 일때수치변경가능 ) - P3900 : 최종빠른운전수행 : 3 ( 모든입력 data에의해연산수행,at P0010=1 ) ( 주 ) P3900=3을수행하면자동으로연산을마친후에 P0010=0으로전환된다. - P1080 : 모터최소주파수 :? Hz ( 0.0 ~ 650.0 Hz ) - P1082 : 모터최대주파수 :? Hz ( 0.0 ~ 650.0 Hz ) - P1120 : 모터가속시간 :? sec ( 0.0 ~ 650.0 Hz ) - P1121 : 모터감속시간 :? sec ( 0.0 ~ 650.0 Hz ) - P0700 : 명령경로선택 : 2 ( Terminal ) - P0701 : 디지탈입력 1 : 16 ( 다단주파수1, P1001로속도설정 ) - P0702 : 디지탈입력 2 : 16 ( 다단주파수3, P1002로속도설정 ) - P0703 : 디지탈입력 3 : 16 ( 다단주파수3, P1003로속도설정 ) - P0704 : 디지탈입력 4 : 16 ( 다단주파수4, P1004로속도설정 ) - P0705 : 디지탈입력 5 : 16 ( 다단주파수5, P1005로속도설정 ) - P0706 : 디지탈입력 6 : 16 ( 다단주파수6, P1006로속도설정 ) - P1000 : 주파수 Main 설정 : 3 ( 다단주파수 ) - P1001 : 다단주파수1 (FF1) :? ( -650 ~ +650 Hz ) - P1002 : 다단주파수2 (FF2) :? ( -650 ~ +650 Hz ) - P1003 : 다단주파수3 (FF3) :? ( -650 ~ +650 Hz ) - P1004 : 다단주파수4 (FF4) :? ( -650 ~ +650 Hz ) - P1005 : 다단주파수5 (FF5) :? ( -650 ~ +650 Hz ) - P1006 : 다단주파수6 (FF6) :? ( -650 ~ +650 Hz ) - P1300 : 출력사양선택 : 1 ( FCC ) - P0005 : Display 표시선택 : 21 ( 실제주파수 ) MM440_ 사용설명서 15 By H.J.Kim
SamHwa Engineering 2003-10-14 주 ) 1. P0701,P0702,P0703,P0704,P0705,P0706=16 이면별도의 Run(On) 명령이없이운전가능하다.(6속운전) 2. Din1,Din2,Din3,Din4,Din5,Din6이모두 On이되면, 설정값 (P1001,P1002,P1003,P1004,P1005,P1006) 이모두합하여져서출력이되며 P1082의값이상이될수없다 MM440_ 사용설명서 16 By H.J.Kim
SamHwa Engineering 2003-10-14 4.1.3.4 1~15속도운전시 Parameter Setting. - P0003 : 사용자사용레벨 : 2 ( 확장 ) - P0004 : 파라메터필터링기능 : 0 ( All parameter ) - P0304 : 모터정격전압 :? V ( at P0010=1 일때수치변경가능 ) - P0305 : 모터정격전류 :? A ( at P0010=1 일때수치변경가능 ) - P0307 : 모터정격용량 :? kw ( at P0010=1 일때수치변경가능 ) - P0310 : 모터정격주파수 :? Hz ( at P0010=1 일때수치변경가능 ) - P0311 : 모터정격rpm :? rpm ( at P0010=1 일때수치변경가능 ) - P3900 : 최종빠른운전수행 : 3 ( 모든입력 data에의해연산수행,at P0010=1 ) ( 주 ) P3900=3을수행하면자동으로연산을마친후에 P0010=0으로전환된다. - P1080 : 모터최소주파수 :? Hz ( 0.0 ~ 650.0 Hz ) - P1082 : 모터최대주파수 :? Hz ( 0.0 ~ 650.0 Hz ) - P1120 : 모터가속시간 :? sec ( 0.0 ~ 650.0 Hz ) - P1121 : 모터감속시간 :? sec ( 0.0 ~ 650.0 Hz ) - P0700 : 명령경로선택 : 2 ( Terminal ) - P0701 : 디지탈입력 1 : 17 ( 다단주파수1~15 + On, 2진코드적용 ) - P0702 : 디지탈입력 2 : 17 ( 다단주파수1~15 + On, 2진코드적용 ) - P0703 : 디지탈입력 3 : 17 ( 다단주파수1~15 + On, 2진코드적용 ) - P0704 : 디지탈입력 4 : 17 ( 다단주파수1~15 + On, 2진코드적용 ) - P1000 : 주파수 Main 설정 : 3 ( 다단주파수 ) - P1001 : 다단주파수1 (FF1) :? ( -650 ~ +650 Hz ) - P1002 : 다단주파수2 (FF2) :? ( -650 ~ +650 Hz ) - P1003 : 다단주파수3 (FF3) :? ( -650 ~ +650 Hz ) - P1004 : 다단주파수4 (FF4) :? ( -650 ~ +650 Hz ) - P1005 : 다단주파수5 (FF5) :? ( -650 ~ +650 Hz ) - P1006 : 다단주파수6 (FF6) :? ( -650 ~ +650 Hz ) - P1007 : 다단주파수7 (FF7) :? ( -650 ~ +650 Hz ) - P1008 : 다단주파수8 (FF8) :? ( -650 ~ +650 Hz ) - P1009 : 다단주파수9 (FF9) :? ( -650 ~ +650 Hz ) - P1010 : 다단주파수10 (FF10) :? ( -650 ~ +650 Hz ) - P1011 : 다단주파수11 (FF11) :? ( -650 ~ +650 Hz ) - P1012 : 다단주파수12 (FF12) :? ( -650 ~ +650 Hz ) - P1013 : 다단주파수13 (FF13) :? ( -650 ~ +650 Hz ) - P1014 : 다단주파수14 (FF14) :? ( -650 ~ +650 Hz ) - P1015 : 다단주파수15 (FF15) :? ( -650 ~ +650 Hz ) - P1300 : 출력사양선택 : 1 ( FCC ) - P0005 : Display 표시선택 : 21 ( 실제주파수 ) MM440_ 사용설명서 17 By H.J.Kim
SamHwa Engineering 2003-10-14 다단 (1~15) 속도용 2 진코드표 Din1 Din2 Din3 Din4 속도설정 Parameter 0 0 0 0 Off( 정지 ) 1 0 0 0 P1001 FF1(1속 ) 0 1 0 0 P1002 FF2(2속 ) 1 1 0 0 P1003 FF3(3속 ) 0 0 1 0 P1004 FF4(4속 ) 1 0 1 0 P1005 FF5(5속 ) 0 1 1 0 P1006 FF6(6속 ) 1 1 1 0 P1007 FF7(7속 ) 0 0 0 1 P1008 FF8(8속 ) 1 0 0 1 P1009 FF9(9속 ) 0 1 0 1 P1010 FF10(10속 ) 1 1 0 1 P1011 FF11(11속 ) 0 0 1 1 P1012 FF12(12속 ) 1 0 1 1 P1013 FF13(13속 ) 0 1 1 1 P1014 FF14(14속 ) 1 1 1 1 P1015 FF15(15속 ) MM440_ 사용설명서 18 By H.J.Kim
* 2 개의아날로그입력사용시 아날로그 1(Ain1) 과아날로그 2(Ain2) 를자동 / 수동의조건으로사용한다. - Digital Input3 을전환용스위치로사용시 - P0809[2] = 1 Copy CDS - P0703[0] = 99 - P0703[1] = 99 - P1000[0] = 2 - P1000[1] = 7 - P0810 = 722.2 * Brake형모터사용시인버터설정 - Relay Output 설정 P0731 = 52.C(52.12) RL1 설정 - MHB(Motor Holding Brake) 사용여부 P1215 = 1 - Time of Holding P1216 (MHB release delay< 풀림지연시간 >) :? sec P1217 (MHB holding delay< 잠김지연시간 >) :? sec
* 제동저항사용시인버터설정 - Designed to operate on a 5% Duty cycle - 연결단자 : B+, B- - Braking resistor function P1237 = 1 or 2 Rate[kW] Voltage[V] Cont. [W] Resistor[ohm] Remarks 0.12 ~ 0.75 230 50 180 1.1 ~ 2.2 120 68 3.0 250 39 4.0 ~ 5.5 300 27 7.5 ~ 15.0 800 10 18.5 ~ 22.0 1200 6.8 30.0 ~ 45.0 2500 3.3 0.37 ~ 1.5 380 ~ 480 100 390 2.2 ~ 4.0 200 160 5.5 ~ 11.0 650 56 15.0 ~ 22.0 1200 27 30.0 ~ 37.0 2200 15 45.0 ~ 75.0 4000 8.2
Braking Resistors for MICROMASTER 440 Instruction Sheet English WARNING Safe operation and performance to specification can only be guaranteed if this equipment is installed by suitably qualified personnel. Make sure that the resistor to be fitted to the MICROMASTER Vector is adequately rated to handle the required level of power dissipation. Using an incorrect braking resistor can cause severe damage to the associated inverter and may result in a fire. All applicable installation, usage and safety regulations regarding high voltage installations must be complied with. If the inverter is already in use, disconnect the prime power and wait at least five minutes for the capacitors to discharge before commencing installation. This equipment must be earthed. Braking resistors get hot during operation - do not touch. Provide adequate clearance and ventilation. A thermal cut-out circuit (see diagram) must be incorporated to protect the equipment from overheating, Technical Data Ambient operating temperature: Storage/transport temperature: Degree of protection: Humidity: -10C to 50C -40 to +70C IP20 0 to 95% (non-condensing) Installation The resistors MUST be installed in a VERTICAL position and secured to a heat resistant surface. At least 100 mm must be left above, below and to the side of the resistor to allow an unimpeded airflow. Connecting Up Resistor Protection It is important that the mains supply to the inverter is provided via a contactor which can disconnect the supply if the resistor overheats. Protection is provided by a thermal cut-out switch (supplied with each resistor). This is wired in-series with the coil supply for the main contactor (see diagram). The thermal switch contacts close again when the resistor temperature falls. Commissioning MICROMASTER Braking Resistors are designed to operate on a 5% duty cycle. To enable the Braking Resistor function, set P1237 = 1. Deutsch WARNUNG Betriebssicherheit und Erreichen der Sollleistung können nur gewährleistet werden, wenn dieses Gerät von qualifiziertem Fachpersonal installiert wird. Der Widerstand, der am MICROMASTER Vector montiert werden soll, muss so ausgelegt sein, dass er die vorgesehene Abgabeleistung aufnehmen kann. Bei Verwendung eines ungeeigneten Bemswiderstands besteht Brandgefahr und die Gefahr schwerer Schäden am zugehörigen Wechselrichter. Sämtliche maßgeblichen Einbau-, Verwendungs- und Sicherheitsvorschriften für Hochspannungsanlagen sind zu beachten. Befindet sich der Wechselrichter bereits in Betrieb, so ist zuerst die Primärstromversorgung abzuschalten und vor Beginn des Einbaus eine Zeit von mindestens fünf Minuten abzuwarten, damit sich die Kondensatoren entladen können. Das Gerät muss geerdet werden. Bremswiderstände heizen sich im Betrieb auf bitte nicht berühren! Achten Sie auf ausreichende Freiräume und Belüftung. Zum Schutz der Geräte gegen Überhitzung ist ein Temperaturschutzschalter (siehe Schaltplan) zwischenzuschalten. Technische Daten Betriebsumgebungstemperatur: -10C bis +50C Lager-/Transporttemperatur: -40 bis +70C Schutzart: IP20 Luftfeuchtigkeit: 0 bis 95% (nicht kondensatbildend) Einbau Die Widerstände MÜSSEN in SENKRECHTER Einbauposition eingebaut und auf einer wärmebeständigen Fläche befestigt werden. Oberhalb, unterhalb und auf den Seiten des Widerstands muss ein Freiraum von mindestens 100 mm bleiben, damit ein ungehinderter Luftstrom gewährleistet ist. Siemens plc 2001
W MAINS POWER INPUT CONTACTOR SUPPLY PE L1 L2 L3 125 V DC 230 V AC Max. D L1 L CONTACTOR W1 D L/L1 N/L2 L3 W B+/DC+ MICROMASTER 440 RESISTOR T1 T2 L1 L B- THERMAL SWITCH Contact Rating 2.5 A D1 D2 W1 FSA & FSB L2 L3 FSC, FSD, FSE & FSF Braking Resistor Selection Resistor MLFB 6SE6400- Inverter Frame Size Inverter Nominal Voltage (V) Max Inverter Power (kw) Continuous Power (W) Peak Power 5% Duty Cycle (12 Seconds) Resistance Ohms +/- 10% DC Voltage Rating Dimensions (mm) (V) L L1 L2 L3 D D1 D2 W W1 Resistor Weight (Kg) 4BC05-0AA0 A 230 0.75 50 1000 180 450 230 217 - - 43.5 - - 72 56 1.0 4BC11-2BA0 B 230 2.2 120 2400 68 450 239 226 - - 43.5 - - 149 138 1.6 4BC12-5CA0 C 230 3.0 250 4500 39 450 285 200 145 170 150 217 185 185 230 3.8 4BC13-0CA0 C 230 5.5 300 6000 27 450 285 200 145 170 150 217 185 185 230 3.8 4BC18-0DA0 D 230 15.0 800 16000 10 450 515 350 205 195 175 242 210 270 315 7.4 4BC21-2EA0 E 230 22.0 1200 24000 6.8 450 645 480 205 195 175 242 210 270 315 10.6 4BC22-5FA0 F 230 45.0 2500 50000 3.3 450 650 510 270 335 315 382 382 400 435 16.7 4BD11-0AA0 A 400 1.5 100 2000 390 900 230 217 - - 43.5 - - 72 56 1.0 4BD12-0BA0 B 400 4.0 200 4000 160 900 239 226 - - 43.5 - - 149 138 1.6 4BD16-5CA0 C 400 11.0 650 13000 56 900 285 200 145 170 150 217 185 185 230 3.8 4BD21-2DA0 D 400 22.0 1200 24000 27 900 515 350 205 195 175 242 210 270 315 7.4 4BD22-2EA0 E 400 37.0 2200 44000 15 900 645 480 205 195 175 242 210 270 315 10.6 4BD24-0FA0 F 400 75.0 4000 80000 8.2 900 650 510 270 335 315 382 382 400 435 16.7 4BE14-5CA0 C 575 5.5 450 9000 120 1100 285 200 145 170 150 217 185 185 230 3.8 4BE16-5CA0 C 575 11.0 650 13000 82 1100 285 200 145 170 150 217 185 185 230 3.8 4BE21-3DA0 D 575 22.0 1300 26000 39 1100 515 350 205 195 175 242 210 270 315 7.4 4BE21-8EA0 E 575 37.0 1900 38000 27 1100 645 480 205 195 175 242 210 270 315 10.6 4BE24-2FA0 F 575 75.0 4200 84000 12 1100 650 510 270 335 315 382 382 400 435 16.7 Siemens plc 2001
Parameter P0004 = 0 (no filter function) allows direct access to the parameters. For BOP and AOP depending on the selected access level P0004 = 2, P0003 = 1 Parameters level 1 concerning the inverter unit P0004 = 2, P0003 = 3, Parameters level 1, 2 and 3 concerning the inverter unit P0004 = 2 Inverter Unit P0004 = 2, P0003 = 2 Parameters level 1 and 2 concerning the inverter unit P0004 = 2, P0003 = 4 Parameters level 1, 2, 3 and 4 concerning the inverter unit P0004 = 21 Alarms, Warnings & Monitoring P0004 = 22 PI Controller P0004 = 2 Inverter Unit P0004 = 3 Motor Data P0004 = 20 Communication P0003 = 1, Access Level Standard P0004 = 4 Speed sensor xp0003 = 3, Access Level E pert P0003 = 2, Access Level Extended P0004 = 13 Motor Control P0003 = 4, Access Level Service P0004 = 5 Technology Application / units P0004 = 12 Drive Features P0004 = 10 Setpoint Channel & Ramp Generator P0004 = 8 Analogue I/O P0004 = 7 Commands and Digital I/O Figure 5-1 Parameter Overview
5.3 Parameter list (short form) Always Explanatory information on following table: Default: Factory setting Level: Access level DS Inverter status (Drive State), indicates the inverter state in which a parameter can be modified (see P0010). C Commissioning U Run T Ready to run QC Quick Commissioning Q Parameter can be modified in the Quick Commissioning state. 1. N Parameter cannot be modified in the Quick Commissioning state. r0000 Drive display - 1 - - P0003 User access level 1 1 CUT N P0004 Parameter filter 0 1 CUT N P0010 Commissioning parameter 0 1 CT N P0014[3] Store mode 0 3 UT N P0199 Equipment system number 0 2 UT N Quick Commissioning Parameter Reset P0100 Europe / North America 0 1 C Q P3900 End of quick commissioning 0 1 C Q Par.-No. Parametername Default Level DS QC P0970 Factory reset 0 1 C N Technological functions Par.-No. Parametername Default Level DS QC P0500[3] Technological application 0 3 CT Q Inverter Unit (P0004 = 2) r0018 Firmware version - 1 - - r0026[1] CO: Act. DC-link voltage - 2 - - r0039 CO: Energy consumpt. meter [kwh] - 2 - - P0040 Reset energy consumption meter 0 2 CT N r0037[5] CO: Inverter temperature [ C] - 3 - - r0070 CO: Act. DC-link voltage - 3 - - r0200 Act. power stack code number - 3 - -
P0201 Power stack code number 0 3 C N r0203 Act. inverter type - 3 - - r0204 Power stack features - 3 - - P0205 Inverter application 0 3 C Q r0206 Rated inverter power [kw] / [hp] - 2 - - r0207 Rated inverter current - 2 - - r0208 Rated inverter voltage - 2 - - r0209 Maximum inverter current - 2 - - P0210 Supply voltage 230 3 CT N r0231[2] Max. cable length - 3 - - P0290 Inverter overload reaction 2 3 CT N P0292 Inverter overload warning 15 3 CUT N P1800 Pulse frequency 4 2 CUT N r1801 CO: Act. pulse frequency - 3 - - P1802 Modulator mode 0 3 CUT N P1820[3] Reverse output phase sequence 0 2 CT N P1911 No. of phase to be identified 3 2 CT N r1925 Identified on-state voltage - 2 - - r1926 Ident. gating unit dead time - 2 - - Motor Data (P0004 = 3) r0035[3] CO: Act. Motor temperature - 2 - - P0300[3] Select motor type 1 2 C Q P0304[3] Rated motor voltage 230 1 C Q P0305[3] Rated motor current 3.25 1 C Q P0307[3] Rated motor power 0.75 1 C Q P0308[3] Rated motor cosphi 0.000 2 C Q P0309[3] Rated motor efficiency 0.0 2 C Q P0310[3] Rated motor frequency 50.00 1 C Q P0311[3] Rated motor speed 0 1 C Q r0313[3] Motor pole pairs - 3 - - P0320[3] Motor magnetizing current 0.0 3 CT Q r0330[3] Rated motor slip - 3 - - r0331[3] Rated magnetization current - 3 - - r0332[3] Rated power factor - 3 - - r0333[3] Rated motor torque - 3 - - P0335[3] Motor cooling 0 2 CT Q P0340[3] Calculation of motor parameters 0 2 CT N P0341[3] Motor inertia [kg*m^2] 0.00180 3 CUT N P0342[3] Total/motor inertia ratio 1.000 3 CUT N P0344[3] Motor weight 9.4 3 CUT N r0345[3] Motor start-up time - 3 - - P0346[3] Magnetization time 1.000 3 CUT N P0347[3] Demagnetization time 1.000 3 CUT N
P0350[3] Stator resistance (line-to-line) 4.0 2 CUT N P0352[3] Cable resistance 0.0 3 CUT N r0384[3] Rotor time constant - 3 - - r0395 CO: Total stator resistance [%] - 3 - - r0396 CO: Act. Rotor resistance - 3 - - P0601[3] Motor temperature sensor 0 2 CUT N P0604[3] Threshold motor temperature 130.0 2 CUT N P0610[3] Motor I2t temperature reaction 2 3 CT N P0625[3] Ambient motor temperature 20.0 3 CUT N P0640[3] Motor overload factor [%] 150.0 2 CUT Q P1910 Select motor data identification 0 2 CT Q r1912[3] Identified stator resistance - 2 - - r1913[3] Identified rotor time constant - 2 - - r1914[3] Ident. Total leakage inductance - 2 - - r1915[3] Ident. Nom. Stator inductance - 2 - - r1916[3] Identified stator inductance 1-2 - - r1917[3] Identified stator inductance 2-2 - - r1918[3] Identified stator inductance 3-2 - - r1919[3] Identified stator inductance 4-2 - - r1920[3] Identified dyn. Leak. Inductance - 2 - - P1960 Speed control optimisation 0 3 CT Q Commands and Digital I/O (P0004 = 7) R0002 Drive state - 2 - - r0019 CO/BO: BOP control word - 3 - - r0050 CO: Active command data set - 2 - - r0052 CO/BO: Act. Status word 1-2 - - r0051[2] CO: Active drive data set (DDS) - 2 - - r0053 CO/BO: Act. Status word 2-2 - - r0054 CO/BO: Act. Control word 1-3 - - r0055 CO/BO: Add. Act. Control word - 3 - - r0403 CO/BO: Encoder status word - 2 - - P0700[3] Selection of command source 2 1 CT Q P0701[3] Function of digital input 1 1 2 CT N P0702[3] Function of digital input 2 12 2 CT N P0703[3] Function of digital input 3 9 2 CT N P0704[3] Function of digital input 4 15 2 CT N P0705[3] Function of digital input 5 15 2 CT N P0706[3] Function of digital input 6 15 2 CT N P0707[3] Function of digital input 7 0 2 CT N P0708[3] Function of digital input 8 0 2 CT N r0720 Number of digital inputs - 3 - - r0722 CO/BO: Binary input values - 2 - - P0719[3] Selection of cmd. & freq. Setp. 0 3 CT N
P0724 Debounce time for digital inputs 3 3 CT N P0725 PNP / NPN digital inputs 1 3 CT N r0730 Number of digital outputs - 3 - - P0731[3] BI: Function of digital output 1 52:3 2 CUT N P0732[3] BI: Function of digital output 2 52:7 2 CUT N P0733[3] BI: Function of digital output 3 0:0 2 CUT N r0747 CO/BO: State of digital outputs - 3 - - P0748 Invert digital outputs 0 3 CUT N P0800[3] BI: Download parameter set 0 0 :0 3 CT N P0801[3] BI: Download parameter set 1 0 :0 3 CT N P0810 BI: CDS bit 0 (Local / Remote) 0:0 2 CUT N P0811 BI: CDS bit 1 0:0 2 CUT N P0809[3] Copy command data set (CDS) 0 2 CT N P0820 BI: DDS bit 0 0 :0 3 CT N P0821 BI: DDS bit 1 0 :0 3 CT N P0819[3] Copy drive data set (DDS) 0 2 CT N P0840[3] BI: ON/OFF1 722 :0 3 CT N P0842[3] BI: ON reverse/off1 0 :0 3 CT N P0844[3] BI: 1. OFF2 1 :0 3 CT N P0845[3] BI: 2. OFF2 19 :1 3 CT N P0848[3] BI: 1. OFF3 1 :0 3 CT N P0849[3] BI: 2. OFF3 1 :0 3 CT N P0852[3] BI: Pulse enable 1:0 3 CT N P1020[3] BI: Fixed freq. Selection Bit 0 0 :0 3 CT N P1021[3] BI: Fixed freq. Selection Bit 1 0 :0 3 CT N P1022[3] BI: Fixed freq. Selection Bit 2 0 :0 3 CT N P1023[3] BI: Fixed freq. Selection Bit 3 722 :3 3 CT N P1026[3] BI: Fixed freq. Selection Bit 4 722 :4 3 CT N P1028[3] BI: Fixed freq. Selection Bit 5 722 :5 3 CT N P1035[3] BI: Enable MOP (UP-command) 19 :13 3 CT N P1036[3] BI: Enable MOP (DOWN-command) 19 :14 3 CT N P1055[3] BI: Enable JOG right 0 :0 3 CT N P1056[3] BI: Enable JOG left 0 :0 3 CT N P1074[3] BI: Disable additional setpoint 0:0 3 CUT N P1110[3] BI: Inhibit neg. freq. Setpoint 0 :0 3 CT N P1113[3] BI : Reverse 722 :1 3 CT N P1124[3] BI: Enable JOG ramp times 0 :0 3 CT N P1140[3] BI: RFG enable 1 :0 3 CT N P1141[3] BI: RFG start 1 :0 3 CT N P1142[3] BI: RFG enable setpoint 1 :0 3 CT N P1230[3] BI: Enable DC braking 0:0 3 CUT N P2103[3] BI: 1. Faults acknowledgement 722 :2 3 CT N P2104[3] BI: 2. Faults acknowledgement 0 :0 3 CT N P2106[3] BI : External fault 1 :0 3 CT N P2220[3] BI: Fixed PID setp. Select Bit 0 0 :0 3 CT N
P2221[3] BI: Fixed PID setp. Select Bit 1 0 :0 3 CT N P2222[3] BI: Fixed PID setp. Select Bit 2 0 :0 3 CT N P2223[3] BI: Fixed PID setp. Select Bit 3 722 :3 3 CT N P2226[3] BI: Fixed PID setp. Select Bit 4 722 :4 3 CT N P2228[3] BI: Fixed PID setp. Select Bit 5 722 :5 3 CT N P2235[3] BI: Enable PID-MOP (UP-cmd) 19 :13 3 CT N P2236[3] BI: Enable PID-MOP (DOWN-cmd) 19 :14 3 CT N Analogue I/O (P0004 = 8) P0295 Inverter fan off delay time 0 3 CUT N r0750 Number of ADCs - 3 - - r0752[2] Act. input of ADC [V] or [ma] - 2 - - P0753[2] Smooth time ADC 3 3 CUT N r0754[2] Act. ADC value after scaling [%] - 2 - - r0755[2] CO: Act. ADC after scal. [4000h] - 2 - - P0756[2] Type of ADC 0 2 CT N P0757[2] Value x1 of ADC scaling [V / ma] 0 2 CUT N P0758[2] Value y1 of ADC scaling 0.0 2 CUT N P0759[2] Value x2 of ADC scaling [V / ma] 10 2 CUT N P0760[2] Value y2 of ADC scaling 100.0 2 CUT N P0761[2] Width of ADC deadband [V / ma] 0 2 CUT N P0762[2] Delay for loss of signal action 10 3 CUT N r0770 Number of DACs - 3 - - P0771[2] CI: DAC 21:0 2 CUT N P0773[2] Smooth time DAC 2 2 CUT N r0774[2] Act. DAC value [V] or [ma] - 2 - - P0776[2] Type of DAC 0 2 CT N P0777[2] Value x1 of DAC scaling 0.0 2 CUT N P0778[2] Value y1 of DAC scaling 0 2 CUT N P0779[2] Value x2 of DAC scaling 100.0 2 CUT N P0780[2] Value y2 of DAC scaling 20 2 CUT N P0781[2] Width of DAC deadband 0 2 CUT N Setpoint Channel and Ramp Generator (P0004 = 10) P1000[3] Selection of frequency setpoint 2 1 CT Q P1001[3] Fixed frequency 1 0.00 2 CUT N P1002[3] Fixed frequency 2 5.00 2 CUT N P1003[3] Fixed frequency 3 10.00 2 CUT N P1004[3] Fixed frequency 4 15.00 2 CUT N P1005[3] Fixed frequency 5 20.00 2 CUT N P1006[3] Fixed frequency 6 25.00 2 CUT N P1007[3] Fixed frequency 7 30.00 2 CUT N P1008[3] Fixed frequency 8 35.00 2 CUT N
P1009[3] Fixed frequency 9 40.00 2 CUT N P1010[3] Fixed frequency 10 45.00 2 CUT N P1011[3] Fixed frequency 11 50.00 2 CUT N P1012[3] Fixed frequency 12 55.00 2 CUT N P1013[3] Fixed frequency 13 60.00 2 CUT N P1016 Fixed frequency mode Bit 0 1 3 CT N P1014[3] Fixed frequency 14 65.00 2 CUT N P1017 Fixed frequency mode Bit 1 1 3 CT N P1015[3] Fixed frequency 15 65.00 2 CUT N P1018 Fixed frequency mode Bit 2 1 3 CT N P1019 Fixed frequency mode Bit 3 1 3 CT N r1024 CO: Act. Fixed frequency - 3 - - P1025 Fixed frequency mode Bit 4 1 3 CT N P1027 Fixed frequency mode Bit 5 1 3 CT N P1032 Inhibit reverse direction of MOP 1 2 CT N P1031[3] Setpoint memory of the MOP 0 2 CUT N P1040[3] Setpoint of the MOP 5.00 2 CUT N r1050 CO: Act. Output freq. Of the MOP - 3 - - P1058[3] JOG frequency right 5.00 2 CUT N P1059[3] JOG frequency left 5.00 2 CUT N P1060[3] JOG ramp-up time 10.00 2 CUT N P1061[3] JOG ramp-down time 10.00 2 CUT N P1070[3] CI : Main setpoint 755:0 3 CT N P1071[3] CI : Main setpoint scaling 1:0 3 CT N P1075[3] CI : Additional setpoint 0:0 3 CT N r1078 CO: Total frequency setpoint - 3 - - P1076[3] CI: Additional setpoint scaling 1:0 3 CT N r1079 CO: Selected frequency setpoint - 3 - - P1080[3] Min. frequency 0.00 1 CUT Q P1082[3] Max. frequency 50.00 1 CT Q P1091[3] Skip frequency 1 0.00 3 CUT N P1092[3] Skip frequency 2 0.00 3 CUT N P1093[3] Skip frequency 3 0.00 3 CUT N P1094[3] Skip frequency 4 0.00 3 CUT N P1101[3] Skip frequency bandwidth 2.00 3 CUT N r1114 CO: Freq. Setp. After dir. Ctrl. - 3 - - r1119 CO: Freq. Setpoint before RFG - 3 - - P1120[3] Ramp-up time 10.00 1 CUT Q P1121[3] Ramp-down time 10.00 1 CUT Q P1130[3] Ramp-up initial rounding time 0.00 2 CUT N P1131[3] Ramp-up final rounding time 0.00 2 CUT N P1132[3] Ramp-down initial rounding time 0.00 2 CUT N P1133[3] Ramp-down final rounding time 0.00 2 CUT N P1134[3] Rounding type 0 2 CUT N P1135[3] OFF3 ramp-down time 5.00 2 CUT Q
r1170 CO: Frequency setpoint after RFG - 3 - - P1257[3] Freq limit for kinetic buffering 2.5 3 CUT N Drive Features (P0004 = 12) P0006 Display mode 2 3 CUT N P0007 Backlight delay time 0 3 CUT N P0005[3] Display selection 21 2 CUT N P0011 Lock for user defined parameter 0 3 CUT N P0012 Key for user defined parameter 0 3 CUT N P0013[20] User defined parameter 0 3 CUT N P1200 Flying start 0 2 CUT N P1202[3] Motor-current: Flying start 100 3 CUT N r1205 Status word: Flying start SLVC - 3 - - P1203[3] Search rate: Flying start 100 3 CUT N P1210 Automatic restart 1 2 CUT N P1211 Number of restart attempts 3 3 CUT N P1215 Holding brake enable 0 2 T N P1216 Holding brake release delay 1.0 2 T N P1217 Holding time after ramp down 1.0 2 T N P1232[3] DC braking current 100 2 CUT N P1233[3] Duration of DC braking 0 2 CUT N P1234[3] DC braking start frequency 650.00 2 CUT N P1237 Dynamic braking 0 2 CUT N P1236[3] Compound braking current 0 2 CUT N r1242 CO: Switch-on level of Vdc-max - 3 - - P1240[3] Configuration of Vdc controller 1 3 CT N P1243[3] Dynamic factor of Vdc-max 100 3 CUT N P1245[3] Switch on level kin. Buffering 76 3 CUT N r1246[3] CO:Switch-on level kin buffering - 3 - - P1247[3] Dyn. Factor of kinetic buffering 100 3 CUT N P1254 Auto detect Vdc switch-on levels 1 3 CT N P1253[3] Vdc-controller output limitation 10 3 CUT N P1256[3] Reaction of kinetic buffering 0 3 CT N Motor Control (P0004 = 13) r0020 CO: Act. frequency setpoint - 3 - - r0021 CO: Act. frequency - 2 - - r0022 Act. rotor speed - 3 - - r0024 CO: Act. output frequency - 3 - - r0025 CO: Act. output voltage - 2 - - r0027 CO: Act. output current - 2 - - r0029 CO: Flux gen. current - 3 - - r0030 CO: Torque gen. current - 3 - -
r0031 CO: Act. torque - 2 - - r0032 CO: Act. power - 2 - - r0038 CO: Act. power factor - 3 - - r0056 CO/BO: Status of motor control - 3 - - r0061 CO: Act. rotor speed - 2 - - r0062 CO: Freq. setpoint - 3 - - r0063 CO: Act. frequency - 3 - - r0064 CO: Dev. frequency controller - 3 - - r0065 CO: Slip frequency - 3 - - r0066 CO: Act. output frequency - 3 - - r0067 CO: Act. output current limit - 3 - - r0068 CO: Output current - 3 - - r0071 CO: Max. output voltage - 3 - - r0072 CO: Act. output voltage - 3 - - r0075 CO: Current setpoint Isd - 3 - - r0076 CO: Act. current Isd - 3 - - r0077 CO: Current setpoint Isq - 3 - - r0078 CO: Act. current Isq - 3 - - r0079 CO: Torque setpoint (total) - 3 - - r0086 CO: Act. active current - 3 - - r0090 CO: Act. rotor angle - 2 - - P0095[10] CI: Display PZD signals 0:0 3 CT N r0096[10] PZD signals - 3 - - r1084 Max. frequency setpoint - 3 - - P1300[3] Control mode 0 2 CT Q P1310[3] Continuous boost 50.0 2 CUT N P1311[3] Acceleration boost 0.0 2 CUT N P1312[3] Starting boost 0.0 2 CUT N P1316[3] Boost end frequency 20.0 3 CUT N P1320[3] Programmable V/f freq. coord. 1 0.00 3 CT N P1321[3] Programmable V/f volt. coord. 1 0.0 3 CUT N P1322[3] Programmable V/f freq. coord. 2 0.00 3 CT N P1323[3] Programmable V/f volt. coord. 2 0.0 3 CUT N P1324[3] Programmable V/f freq. coord. 3 0.00 3 CT N P1325[3] Programmable V/f volt. coord. 3 0.0 3 CUT N P1330[3] CI: Voltage setpoint 0:0 3 T N P1333[3] Start frequency for FCC 10.0 3 CUT N r1337 CO: V/f slip frequency - 3 - - P1335[3] Slip compensation 0.0 2 CUT N P1336[3] Slip limit 250 2 CUT N P1338[3] Resonance damping gain V/f 0.00 3 CUT N P1340[3] Imax controller prop. gain 0.000 3 CUT N r1343 CO: Imax controller freq. output - 3 - - P1341[3] Imax controller integral time 0.300 3 CUT N r1344 CO: Imax controller volt. output - 3 - -
P1345[3] Imax controller prop. gain 0.250 3 CUT N P1346[3] Imax controller integral time 0.300 3 CUT N P1350[3] Voltage soft start 0 3 CUT N P1400[3] Configuration of speed control 1 3 CUT N r1407 CO/BO: Status 2 of motor control - 3 - - r1438 CO: Freq. setpoint to controller - 3 - - P1452[3] Filter time for act.speed (SLVC) 4 3 CUT N P1460[3] Gain speed controller 3.0 2 CUT N P1462[3] Integral time speed controller 400 2 CUT N P1470[3] Gain speed controller (SLVC) 3.0 2 CUT N P1472[3] Integral time n-ctrl. (SLVC) 400 2 CUT N P1477[3] BI: Set integrator of n-ctrl. 0:0 3 CUT N P1478[3] CI: Set integrator value n-ctrl. 0:0 3 UT N r1482 CO: Integral output of n-ctrl. - 3 - - r1490 CO: Droop frequency - 3 - - P1488[3] Droop input source 0 3 CUT N P1489[3] Droop scaling 0.05 3 CUT N P1492[3] Enable droop 0 3 CUT N P1496[3] Scaling accel. precontrol 0.0 3 CUT N P1499[3] Scaling accel. torque control 100.0 3 CUT N P1500[3] Selection of torque setpoint 0 2 CT Q P1501[3] BI: Change to torque control 0:0 3 CT N P1503[3] CI: Torque setpoint 0:0 3 T N r1508 CO: Torque setpoint - 2 - - P1511[3] CI: Additional torque setpoint 0:0 3 T N r1515 CO: Additional torque setpoint - 2 - - r1518 CO: Acceleration torque - 3 - - P1520[3] CO: Upper torque limit 5.13 2 CUT N P1521[3] CO: Lower torque limit -5.13 2 CUT N P1522[3] CI: Upper torque limit 1520:0 3 T N P1523[3] CI: Lower torque limit 1521:0 3 T N r1526 CO: Upper torque limitation - 3 - - r1527 CO: Lower torque limitation - 3 - - P1525[3] Scaling lower torque limit 100.0 3 CUT N P1530[3] Motoring power limitation 0.75 2 CUT N P1531[3] Regenerative power limitation -0.75 2 CUT N r1538 CO: Upper torque limit (total) - 2 - - r1539 CO: Lower torque limit (total) - 2 - - P1570[3] CO: Fixed value flux setpoint 100.0 2 CUT N P1574[3] Dynamic voltage headroom 10 3 CUT N P1580[3] Efficiency optimization 0 2 CUT N P1582[3] Smooth time for flux setpoint 15 3 CUT N r1598 CO: Flux setpoint (total) - 3 - - P1596[3] Int. time field weak. controller 50 3 CUT N P1610[3] Continuous torque boost (SLVC) 50.0 2 CUT N
P1611[3] Acc. torque boost (SLVC) 0.0 2 CUT N P1740 Gain for oscillation damping 0.000 3 CUT N r1751 Status word of motor model - 3 - - P1750[3] Control word of motor model 1 3 CUT N P1755[3] Start-freq. motor model (SLVC) 5.0 3 CUT N P1756[3] Hyst.-freq. motor model (SLVC) 50.0 3 CUT N P1758[3] T(wait) transit to feed-fwd-mode 1500 3 CUT N P1759[3] T(wait) for n-adaption to settle 100 3 CUT N P1764[3] Kp of n-adaption (SLVC) 0.2 3 CUT N r1770 CO: Prop. output of n-adaption - 3 - - r1771 CO: Int. output of n-adaption - 3 - - r1782 Output of Rs-adaptation - 3 - - P1780[3] Control word of Rs/Rr-adaption 3 3 CUT N r1787 Output of Xm-adaption - 3 - - P2480[3] Position mode 1 3 CT N P2481[3] Gearbox ratio input 1.00 3 CT N P2482[3] Gearbox ratio output 1.00 3 CT N P2484[3] No. of shaft turns = 1 Unit 1.0 3 CUT N r2489 Act. number of shaft revolutions - 3 - - P2487[3] Positional error trim value 0.00 3 CUT N P2488[3] No. final shaft turns = 1 Unit 1.0 3 CUT N Communication (P0004 = 20) P0918 CB address 3 2 CT N P0927 Parameter changeable via 15 2 CUT N r0965 Profibus profile - 3 - - r0967 Control word 1-3 - - r0968 Status word 1-3 - - r0964[5] Firmware version data - 3 - - P0971 Transfer data from RAM to EEPROM 0 3 CUT N P2000[3] Reference frequency 50.00 2 CT N P2001[3] Reference voltage 1000 3 CT N P2002[3] Reference current 0.10 3 CT N P2003[3] Reference torque 0.75 3 CT N r2004[3] Reference power - 3 - - P2009[2] USS normalization 0 3 CT N P2010[2] USS baudrate 6 2 CUT N P2011[2] USS address 0 2 CUT N P2012[2] USS PZD length 2 3 CUT N P2013[2] USS PKW length 127 3 CUT N P2014[2] USS telegram off time 0 3 CT N r2015[8] CO: PZD from BOP link (USS) - 3 - - P2016[8] CI: PZD to BOP link (USS) 52:0 3 CT N r2018[8] CO: PZD from COM link (USS) - 3 - -
r2024[2] USS error-free telegrams - 3 - - P2019[8] CI: PZD to COM link (USS) 52:0 3 CT N r2025[2] USS rejected telegrams - 3 - - r2026[2] USS character frame error - 3 - - r2027[2] USS overrun error - 3 - - r2028[2] USS parity error - 3 - - r2029[2] USS start not identified - 3 - - r2030[2] USS BCC error - 3 - - r2032 BO: CtrlWrd1 from BOP link (USS) - 3 - - r2031[2] USS length error - 3 - - r2033 BO: CtrlWrd2 from BOP link (USS) - 3 - - r2036 BO: CtrlWrd1 from COM link (USS) - 3 - - r2037 BO: CtrlWrd2 from COM link (USS) - 3 - - P2040 CB telegram off time 20 3 CT N P2041[5] CB parameter 0 3 CT N r2050[8] CO: PZD from CB - 3 - - r2053[5] CB identification - 3 - - P2051[8] CI: PZD to CB 52:0 3 CT N r2054[7] CB diagnosis - 3 - - r2090 BO: Control word 1 from CB - 3 - - r2091 BO: Control word 2 from CB - 3 - - Alarms, Warnings and Monitoring (P0004 = 21) r0947[8] Last fault code - 2 - - r0948[12] Fault time - 3 - - r0949[8] Fault value - 3 - - P0952 Total number of faults 0 3 CT N P2100[3] Alarm number selection 0 3 CT N P2101[3] Stop reaction value 0 3 CT N r2110[4] Warning number - 2 - - P2111 Total number of warnings 0 3 CT N r2114[2] Run time counter - 3 - - P2115[3] AOP real time clock 0 3 CT N P2150[3] Hysteresis frequency f_hys 3.00 3 CUT N P2151[3] CI: Monitoring speed setpoint 0:0 3 CUT N P2152[3] CI: Act. monitoring speed 0:0 3 CUT N P2153[3] Time-constant speed filter 5 2 CUT N P2155[3] Threshold frequency f_1 30.00 3 CUT N P2156[3] Delay time of threshold freq f_1 10 3 CUT N P2157[3] Threshold frequency f_2 30.00 2 CUT N P2158[3] Delay time of threshold freq f_2 10 2 CUT N P2159[3] Threshold frequency f_3 30.00 2 CUT N P2160[3] Delay time of threshold freq f_3 10 2 CUT N P2161[3] Min. threshold for freq. setp. 3.00 2 CUT N
P2162[3] Hysteresis freq. for overspeed 20.00 2 CUT N P2163[3] Entry freq. for perm. deviation 3.00 2 CUT N P2164[3] Hysteresis frequency deviation 3.00 3 CUT N P2165[3] Delay time permitted deviation 10 2 CUT N P2166[3] Delay time ramp up completed 10 2 CUT N P2167[3] Switch-off frequency f_off 1.00 3 CUT N P2168[3] Delay time T_off 10 3 CUT N r2169 CO: Act. filtered frequency - 2 - - P2170[3] Threshold current I_thresh 100.0 3 CUT N P2171[3] Delay time current 10 3 CUT N P2172[3] Threshold DC-link voltage 800 3 CUT N P2173[3] Delay time DC-link voltage 10 3 CUT N P2174[3] Torque threshold T_thresh 5.13 2 CUT N P2176[3] Delay time for torque threshold 10 2 CUT N P2177[3] Delay time for motor is blocked 10 2 CUT N P2178[3] Delay time for motor pulled out 10 2 CUT N P2179 Current limit for no load ident. 3.0 3 CUT N P2180 Delay time for no load ident. 2000 3 CUT N P2181[3] Belt failure detection mode 0 2 CT N P2182[3] Belt threshold frequency 1 5.00 3 CUT N P2183[3] Belt threshold frequency 2 30.00 2 CUT N P2184[3] Belt threshold frequency 3 50.00 2 CUT N P2185[3] Upper torque threshold 1 99999.0 2 CUT N P2186[3] Lower torque threshold 1 0.0 2 CUT N P2187[3] Upper torque threshold 2 99999.0 2 CUT N P2188[3] Lower torque threshold 2 0.0 2 CUT N P2189[3] Upper torque threshold 3 99999.0 2 CUT N P2190[3] Lower torque threshold 3 0.0 2 CUT N P2192[3] Time delay for belt failure 10 2 CUT N r2197 CO/BO: Monitoring word 1-2 - - r2198 CO/BO: Monitoring word 2-2 - - PI Controller (P0004 = 22) P2200[3] BI: Enable PID controller 0:0 2 CUT N P2201[3] Fixed PID setpoint 1 0.00 2 CUT N P2202[3] Fixed PID setpoint 2 10.00 2 CUT N P2203[3] Fixed PID setpoint 3 20.00 2 CUT N P2204[3] Fixed PID setpoint 4 30.00 2 CUT N P2205[3] Fixed PID setpoint 5 40.00 2 CUT N P2206[3] Fixed PID setpoint 6 50.00 2 CUT N P2207[3] Fixed PID setpoint 7 60.00 2 CUT N P2208[3] Fixed PID setpoint 8 70.00 2 CUT N P2209[3] Fixed PID setpoint 9 80.00 2 CUT N P2210[3] Fixed PID setpoint 10 90.00 2 CUT N
P2211[3] Fixed PID setpoint 11 100.00 2 CUT N P2212[3] Fixed PID setpoint 12 110.00 2 CUT N P2213[3] Fixed PID setpoint 13 120.00 2 CUT N P2214[3] Fixed PID setpoint 14 130.00 2 CUT N P2215[3] Fixed PID setpoint 15 130.00 2 CUT N P2216 Fixed PID setpoint mode - Bit 0 1 3 CT N P2217 Fixed PID setpoint mode - Bit 1 1 3 CT N P2218 Fixed PID setpoint mode - Bit 2 1 3 CT N P2219 Fixed PID setpoint mode - Bit 3 1 3 CT N r2224 CO: Act. fixed PID setpoint - 2 - - P2225 Fixed PID setpoint mode - Bit 4 1 3 CT N P2227 Fixed PID setpoint mode - Bit 5 1 3 CT N P2231[3] Setpoint memory of PID-MOP 0 2 CUT N P2232 Inhibit rev. direct. of PID-MOP 1 2 CT N P2240[3] Setpoint of PID-MOP 10.00 2 CUT N r2250 CO: Output setpoint of PID-MOP - 2 - - P2251 PID mode 0 3 CT N P2253[3] CI: PID setpoint 0:0 2 CUT N P2254[3] CI: PID trim source 0:0 3 CUT N P2255 PID setpoint gain factor 100.00 3 CUT N P2256 PID trim gain factor 100.00 3 CUT N P2257 Ramp-up time for PID setpoint 1.00 2 CUT N P2258 Ramp-down time for PID setpoint 1.00 2 CUT N r2260 CO: PID setpoint after PID-RFG - 2 - - P2261 PID setpoint filter timeconstant 0.00 3 CUT N r2262 CO: Filtered PID setp. after RFG - 3 - - P2263 PID controller type 0 3 CT N P2264[3] CI: PID feedback 755:0 2 CUT N P2265 PID feedback filter timeconstant 0.00 2 CUT N r2266 CO: PID filtered feedback - 2 - - P2267 Max. value for PID feedback 100.00 3 CUT N P2268 Min. value for PID feedback 0.00 3 CUT N P2269 Gain applied to PID feedback 100.00 3 CUT N P2270 PID feedback function selector 0 3 CUT N P2271 PID transducer type 0 2 CUT N r2272 CO: PID scaled feedback - 2 - - r2273 CO: PID error - 2 - - P2274 PID derivative time 0.000 2 CUT N P2280 PID proportional gain 3.000 2 CUT N P2285 PID integral time 0.000 2 CUT N P2291 PID output upper limit 100.00 2 CUT N P2292 PID output lower limit 0.00 2 CUT N P2293 Ramp-up /-down time of PID limit 1.00 3 CUT N r2294 CO: Act. PID output - 2 - - P2295 Gain applied to PID output 100.00 3 CUT N
P2350 PID autotune enable 0 2 CUT N P2354 PID tuning timeout length 240 3 CUT N P2355 PID tuning offset 5.00 3 CUT N P2800 Enable FFBs 0 3 CUT N P2801[17] Activate FFBs 0 3 CUT N P2802[14] Activate FFBs 0 3 CUT N P2810[2] BI: AND 1 0:0 3 CUT N r2811 BO: AND 1-3 - - P2812[2] BI: AND 2 0:0 3 CUT N r2813 BO: AND 2-3 - - P2814[2] BI: AND 3 0:0 3 CUT N r2815 BO: AND 3-3 - - P2816[2] BI: OR 1 0:0 3 CUT N r2817 BO: OR 1-3 - - P2818[2] BI: OR 2 0:0 3 CUT N r2819 BO: OR 2-3 - - P2820[2] BI: OR 3 0:0 3 CUT N r2821 BO: OR 3-3 - - P2822[2] BI: XOR 1 0:0 3 CUT N r2823 BO: XOR 1-3 - - P2824[2] BI: XOR 2 0:0 3 CUT N r2825 BO: XOR 2-3 - - P2826[2] BI: XOR 3 0:0 3 CUT N r2827 BO: XOR 3-3 - - P2828 BI: NOT 1 0:0 3 CUT N r2829 BO: NOT 1-3 - - P2830 BI: NOT 2 0:0 3 CUT N r2831 BO: NOT 2-3 - - P2832 BI: NOT 3 0:0 3 CUT N r2833 BO: NOT 3-3 - - P2834[4] BI: D-FF 1 0:0 3 CUT N r2835 BO: Q D-FF 1-3 - - r2836 BO: NOT-Q D-FF 1-3 - - P2837[4] BI: D-FF 2 0:0 3 CUT N r2838 BO: Q D-FF 2-3 - - r2839 BO: NOT-Q D-FF 2-3 - - P2840[2] BI: RS-FF 1 0:0 3 CUT N r2841 BO: Q RS-FF 1-3 - - r2842 BO: NOT-Q RS-FF 1-3 - - P2843[2] BI: RS-FF 2 0:0 3 CUT N r2844 BO: Q RS-FF 2-3 - - r2845 BO: NOT-Q RS-FF 2-3 - - P2846[2] BI: RS-FF 3 0:0 3 CUT N r2847 BO: Q RS-FF 3-3 - - r2848 BO: NOT-Q RS-FF 3-3 - -
P2849 BI: Timer 1 0:0 3 CUT N P2850 Delay time of timer 1 0 3 CUT N P2851 Mode timer 1 0 3 CUT N r2852 BO: Timer 1-3 - - r2853 BO: Nout timer 1-3 - - P2854 BI: Timer 2 0:0 3 CUT N P2855 Delay time of timer 2 0 3 CUT N P2856 Mode timer 2 0 3 CUT N r2857 BO: Timer 2-3 - - r2858 BO: Nout timer 2-3 - - P2859 BI: Timer 3 0:0 3 CUT N P2860 Delay time of timer 3 0 3 CUT N P2861 Mode timer 3 0 3 CUT N r2862 BO: Timer 3-3 - - r2863 BO: Nout timer 3-3 - - P2864 BI: Timer 4 0:0 3 CUT N P2865 Delay time of timer 4 0 3 CUT N P2866 Mode timer 4 0 3 CUT N r2867 BO: Timer 4-3 - - r2868 BO: Nout timer 4-3 - - P2869[2] CI: ADD 1 755:0 3 CUT N r2870 CO: ADD 1-3 - - P2871[2] CI: ADD 2 755:0 3 CUT N r2872 CO: ADD 2-3 - - P2873[2] CI: SUB 1 755:0 3 CUT N r2874 CO: SUB 1-3 - - P2875[2] CI: SUB 2 755:0 3 CUT N r2876 CO: SUB 2-3 - - P2877[2] CI: MUL 1 755:0 3 CUT N r2878 CO: MUL 1-3 - - P2879[2] CI: MUL 2 755:0 3 CUT N r2880 CO: MUL 2-3 - - P2881[2] CI: DIV 1 755:0 3 CUT N r2882 CO: DIV 1-3 - - P2883[2] CI: DIV 2 755:0 3 CUT N r2884 CO: DIV 2-3 - - P2885[2] CI: CMP 1 755:0 3 CUT N r2886 BO: CMP 1-3 - - P2887[2] CI: CMP 2 755:0 3 CUT N r2888 BO: CMP 2-3 - - P2889 CO: Fixed setpoint 1 in [%] 0 3 CUT N P2890 CO: Fixed setpoint 2 in [%] 0 3 CUT N
Encoder P0400[3] Select encoder type 0 2 CT N P0408[3] Encoder pulses per revolution 1024 2 CT N P0491[3] Reaction on speed signal loss 0 2 CT N P0492[3] Allowed speed difference 10.00 2 CT N P0494[3] Delay speed loss reaction 10 2 CUT N
5.4 Command and Drive Datasets - Overview Command Datasets (CDS) ParNr ParText 0701[3] Function of digital input 1 0702[3] Function of digital input 2 0703[3] Function of digital input 3 0704[3] Function of digital input 4 0705[3] Function of digital input 5 0706[3] Function of digital input 6 0707[3] Function of digital input 7 0708[3] Function of digital input 8 0719[3] Selection of cmd. & freq. setp. 0731[3] BI: Function of digital output 1 0732[3] BI: Function of digital output 2 0733[3] BI: Function of digital output 3 0800[3] BI: Download parameter set 0 0801[3] BI: Download parameter set 1 0840[3] BI: ON/OFF1 0842[3] BI: ON reverse/off1 0844[3] BI: 1. OFF2 0845[3] BI: 2. OFF2 0848[3] BI: 1. OFF3 0849[3] BI: 2. OFF3 0852[3] BI: Pulse enable 1000[3] Selection of frequency setpoint 1020[3] BI: Fixed freq. selection Bit 0 1021[3] BI: Fixed freq. selection Bit 1 1022[3] BI: Fixed freq. selection Bit 2 1023[3] BI: Fixed freq. selection Bit 3 1026[3] BI: Fixed freq. selection Bit 4 1028[3] BI: Fixed freq. selection Bit 5 1035[3] BI: Enable MOP (UP-command) 1036[3] BI: Enable MOP (DOWN-command) 1055[3] BI: Enable JOG right 1056[3] BI: Enable JOG left 1070[3] CI: Main setpoint 1071[3] CI: Main setpoint scaling 1074[3] BI: Disable additional setpoint 1075[3] CI: Additional setpoint 1076[3] CI: Additional setpoint scaling 1110[3] BI: Inhibit neg. freq. setpoint 1113[3] BI: Reverse 1124[3] BI: Enable JOG ramp times 1140[3] BI: RFG enable ParNr ParText 1141[3] BI: RFG start 1142[3] BI: RFG enable setpoint 1230[3] BI: Enable DC braking 1330[3] CI: Voltage setpoint 1477[3] BI: Set integrator of n-ctrl. 1478[3] CI: Set integrator value n-ctrl. 1500[3] Selection of torque setpoint 1501[3] BI: Change to torque control 1503[3] CI: Torque setpoint 1511[3] CI: Additional torque setpoint 1522[3] CI: Upper torque limit 1523[3] CI: Lower torque limit 2103[3] BI: 1. Faults acknowledgement 2104[3] BI: 2. Faults acknowledgement 2106[3] BI: External fault 2151[3] CI: Monitoring speed setpoint 2152[3] CI: Act. monitoring speed 2200[3] BI: Enable PID controller 2220[3] BI: Fixed PID setp. select Bit 0 2221[3] BI: Fixed PID setp. select Bit 1 2222[3] BI: Fixed PID setp. select Bit 2 2223[3] BI: Fixed PID setp. select Bit 3 2226[3] BI: Fixed PID setp. select Bit 4 2228[3] BI: Fixed PID setp. select Bit 5 2235[3] BI: Enable PID-MOP (UP-cmd) 2236[3] BI: Enable PID-MOP (DOWN-cmd) 2253[3] CI: PID setpoint 2254[3] CI: PID trim source 2264[3] CI: PID feedback