내진설계를위한혁신적인힐티앵커솔루션 기술부황희선과장 2016. 06. 10 1
Contents I. 후설치앵커의분류 II. 내진설계에대한최근동향 III. 후시공앵커의내진성능개념 IV. 중하중용내진앵커 - Hilti HUS3 스크류앵커 V. 고하중용내진앵커 - HY200 SAFEset 시스템 2
후설치앵커의분류 Post-installed Anchor 후설치앵커 Mechanical Anchor 기계식앵커 Adhesive Anchor 부착식앵커 3
후설치기계식앵커의분류 HUS 3 Post-installed mechanical anchor 후설치기계식앵커 Screw anchor 스크류앵커 Expansion anchor 확장앵커 Undercut anchor 언더컷앵커 HDA HKD HSL-3 Torque-controlled 비틀림제어확장앵커 Displacement-controlled 변위제어확장앵커 HST HSA Sleeve anchor 슬리브확장앵커 Wedge anchor 쐐기확장앵커 4
후설치부착식앵커의분류 Post-installed adhesive anchor 후설치부착식앵커 Capsule anchor 캡슐형앵커 Injection anchor 주입형앵커 RE500 HVU HY200 5
Contents I. 후설치앵커의분류 II. 내진설계에대한최근동향 III. 후시공앵커의내진성능개념 IV. 중하중용내진앵커 - Hilti HUS3 스크류앵커 V. 고하중용내진앵커 - HY200 SAFEset 시스템 6
지진에대한고려가중요한이유 1. 내진설계의필요성 - 많은나라에서내진에대해명확한규정을가지고있다. - 지역이나국가에관계없이설계자들에게내진설계의필요성이증대되고있다. 7
지진에대한고려가중요한이유 2. 내진은구조재뿐아니라비구조재에도필요로하고있다. - 내진설계에서는접합부의안전이가장중요한요소. - 비구조요소는내진설계가이루어지지않고현장에서결정되는경우가많음. - 비구조재의적절한내진설계는지진으로인한피해를최소화할수있다. 지진으로인한피해복구비용의평균값 Source: Taghavi S. and Miranda E.: Seismic Performance and Loss Assessment of Nonstructural Building Components, Proceedings of 7th National Conference on Earthquake Engineering, Boston, 2002. 8
9
10
Contents I. 후설치앵커의분류 II. 내진설계에대한최근동향 III. 후시공앵커의내진성능개념 IV. 중하중용내진앵커 - Hilti HUS3 스크류앵커 V. 고하중용내진앵커 - HY200 SAFEset 시스템 11
지진시콘크리트는균열콘크리트상태 1. 지진시콘크리트는압축영역과인장영역이불명확해져서균열콘크리트로 간주한다. 이경우균열발생은대부분앵커가설치된부위를따라서 발생한다 : 앵커홀주위에응력집중현상 (notch effect) 앵커의확장력또는앵커에작용하는하중으로인해콘크리트에응력유발 Source: Prof. Rolf Eligehausen, University of Stuttgart: tests to asses the likelihood of cracks intercepting the position of anchors and anchor holes 12
균열발생시앵커성능의변화 2. 앵커주위에균열이발생하게되면응력의비대칭적인분산으로인해하중 전달양상이달라지게된다. 균열면 비균열콘크리트에서의응력분산 균열콘크리트에서의응력분산 균열콘크리트에서사용이가능한앵커만이내진성능을가질수있다. 13
Tension Shear Crack width 지진하중은단순한균열상태보다훨씬극한상태 3. 지진작용시앵커는아래의상황에저항할수있어야한다 : 반복하중 (Load cycling) 반복되는균열 (Crack cycling) w/ larger crack width 앵커의내진에대한검증은반드시정해진규정에따라테스트를수행해야한다. 14
후시공앵커의내진설계는검증테스트, 승인된기술자료 및설계코드를필요로한다. US Europe 앵커의내진성능 검증기준 ACI 355.4 with ICC-ES AC193/AC308 ETAG 001, Annex E 기술자료 ( 성능검증근거 ) ICC-ES Evaluation Service Report: ESR European Technical Approval: ETA 앵커의내진설계법 ACI 318 Appendix D AC308 EOTA TR045 15
European codes (EOTA TR045) US codes (ASCE 7) 유럽코드와미국코드의내진범주 ( 내진용앵커사용필요 ) 구조요소와비구조요소 Seismic Design Category (SDC) Importance Class II or III Importance Class IV A No seismic requirements B C - F ICC-ES seismic approved Seismic acceleration Importance Class II, III or IV < 0.05g Not seismic 0.05g to 0.1g > 0.1g 구조요소 C2 Building importance I for >0.05g requires C1 Seismic acceleration 비구조요소 Importance Class II or III < 0.05g Not seismic Importance Class IV 0.05g to 0.1g C1 C2 > 0.1g C2 Building importance I for >0.05g requires C1 16
유럽코드 : 2 가지내진범주로구분해서승인. 내진성능범주 C1 0.5mm 정지균열상태에서반복하중을가해서지진을형상화함. C1 Pulsating tension tests Alternating shear tests Dw= 0.5mm Note: 균열콘크리트에서의정적성능테스트시균열폭은 0.3mm 17
유럽코드 : 2 가지내진범주로구분해서승인. 내진성능범주 C2 0.8mm 동적균열상태에서반복하중을가해서지진을형상화함. C2 Pulsating tension tests Alternating shear tests Open/closing crack width Dw= 0.8mm Note: 균열콘크리트에서의정적성능테스트시균열폭은 0.3mm Dw = 0 0.8mm 18
US 코드 : 1 가지범주를대상으로승인 US 내진관련승인 0.5mm 정지균열상태에서반복하중을가해서지진을형상화함. Pulsating tension tests Alternating shear tests = C1 Dw= 0.5mm Note: 균열콘크리트에서의정적성능테스트시균열폭은 0.3mm 19
힐티내진성능인증앵커 (ICC-ESR / ETA C1&C2) HIT-HY 200 + HIT-Z ICC-ESR / ETA C1&C2 HIT-HY 200 + HIT-V ICC-ESR / ETA C1 HIT-RE 500-SD + HIT-V ICC-ESR / ETA C1 HDA ICC-ESR / ETA C1&C2 (pending) HSL-3 ICC-ESR HST ETA C1&C2 KB-TZ ICC-ESR HUS3 ETA C1 KH-EZ ICC-ESR 20
Contents I. 후설치앵커의분류 II. 내진설계에대한최근동향 III. 후시공앵커의내진성능개념 IV. 중하중용내진앵커 - Hilti HUS3 스크류앵커 V. 고하중용내진앵커 - HY200 SAFEset 시스템 21
중하중용내진앵커 - Hilti HUS3 스크류앵커 큰몸통직경보다높은하중에저항가능 ( 기존스크류대비 66%, 스터드앵커대비 33%) σ1 σ2 > σ1 최적화된나사산높은설치품질확보가능 «Not confined» «Confined» 커팅날균일한품질의설치가능 2 타입의앵커헤드현장상황에맞도록헤드타입선정가능 Innovations 1. 다양한모재에적용가능 : 콘크리트 ( 균열및비균열 ), Hollow core slab, Masonry 2. Approval : 내진성능확보 (ETA & ICC-ES) / 조정가능 (Adjustability process) 에대한인증 3. 빠른시공속도 : 스터드앵커대비 50% 더빠른설치 4. 높은시공신뢰성 : 특정토크값이필요없음 22
하중저감없이현장여건에맞는설치유연성발휘 Install anchor Unscrew anchor Add shims to align base plate Re-screw anchor Base plate Max 10mm Max 10mm Uneven surface Concrete 10mm 까지풀었다가다시조였을때, 하중저감이없음 (ETA 인증서보유 - HUS3 8 & 10 (2 번 X 10mm)) 23
3 가지설치깊이제공으로인한선택의다양성 Embedment depth HUS3-H 10 & Stud anchor M12 Ø 12 Stud anchor 7,6 kn Ø 10 Ø 10 Ø 10 h mom3 h nom2 h nom1 Lowest cost Lowest cost per fastening point with highest productivity Replace studs Same performance as stud anchors with high productivity +24% loads Compared to stud anchors 24% higher tension loads HUS3-H 10 h nom1 HUS3-H 10 h nom2 HUS3-H 10 4,6 kn 7,7 kn +1% 9,4 kn h nom3 100 90 80 70 60 50 40 30 20 10 0 +24% 24
HUS3 는짧은모서리거리와앵커간간격을제공 25
주요적용분야 소방시설내진설계 커튼월고정 / 창호고정 내진보강 / 철판보강 파이프랙고정 핸드레일고정 진동셔터및기계장치고정 26
Contents I. 후설치앵커의분류 II. 내진설계에대한최근동향 III. 후시공앵커의내진성능개념 IV. 중하중용내진앵커 - Hilti HUS3 스크류앵커 V. 고하중용내진앵커 - HY200 SAFEset 시스템 27
혁신적인고성능 HY200 시스템 - HY200 + Hollow Drill Bit + HIT-Z HY200 SAFEset System 은균열콘크리트, 내진설계에대한최고의솔루션 Adhesive Anchor Rod 내진솔루션 Non-cleaning systems ICC-ESR ETA C1 HIT-HY200 HIT-V rod Hollow Drill Bit & Vacuum cleaner ICC-ESR ETA C1&C2 HIT-HY200 HIT-Z rod 28
Concrete Threaded Rod Concrete Threaded Rod Load [kn] 부착식앵커사용시먼지청소의중요성 During the approval process tests are done with reduced clearing to check the robustness of the chemical anchor system Mortar Ultimate resistance With hole cleaning Mortar + Dust Improper hole cleaning Displacement [mm] 29
Hollow drill bit 를적용하여안전성및작업속도향상 Hollow drill bit : Drilling과 Cleaning을동시에할수있는드릴비트 혁신적인시공품질향상으로케미컬앵커의부착강도 100% 발휘가능 60% 빠른작업속도로생산성향상 Video: mode of operation air dust Combination of robustness of Hilti drill bits + suitable flow behaviour for proper cleaning of bore holes requires intensive numerical simulation and tests. Numerical simulation: Distribution of pressure inside and outside the hollow drill bit; vacuum by VC 20 Numerical simulation: Transition from Hollow Drill Bit to Adapter: Traces and speed of dust Numerical simulation: Flow behaviour at the head and in the gap between bore hole and drill bit. 30
Hollow drill bit 사용천공작업 31
Load [kn] Load [kn] SAFE Set HIT-HY 200 with HIT-Z rod Hilti HIT-HY 200 + HIT-Z Regular threaded rod w/ injection mortar Ultimate resistance Without hole cleaning Ultimate resistance With hole cleaning With hole cleaning Without hole cleaning Displacement [mm] Displacement [mm] 32
실제규모내진시험 (Real scale seismic testing) (1) 7-story structure [2006] - Piping support and anchoring system 33
실제규모내진시험 (Real scale seismic testing) (2) BNCS was the latest world landmark in real scale seismic testing Every detail was recorded (video, crack openings, anchor forces ) Post-installed anchors as well as cast-in channels were studied 34
These investigations offer an understand of the behavior of each anchor during seismic loading Anchor Load [kn] 40.0 20.0 0.0 20.0 Anchor loading Anchor 2 Anchor 4 Crack Width [mm] Anchor 1 Anchor 3 40.0 0.0 9.0 10.0 11.0 12.0 13.0 14.0 9.0 10.0 11.0 12.0 13.0 14.0 10.0 Time [s] 9.0 Time [s] Anchor 1 8.0 Anchor displacement 7.0 Anchor 2 6.0 Anchor 3 5.0 Anchor 4 4.0 3.0 2.0 1.0 0.0 9.0 10.0 11.0 12.0 13.0 14.0 Time History Time [s] 30.0 9.00 Load [kn] 20.0 10.0 Load Displacement Crack Width Anchor Displacement [mm] 0.0 0.00 8.0 9.0 10.0 11.0 12.0 13.0 14.0 15.0 Time [s] 1.0 0.8 0.6 0.4 0.2 Wcr 1 Wcr 2 Wcr 3 Wcr 4 Concrete cracks Correlation load / displacement / concrete cracks 8.00 7.00 6.00 5.00 4.00 3.00 2.00 1.00 Displacement [mm] 35
HIT HY200 + HIT-Z load transfer mechanism 36
HY200 SAFEset Solution 에어컴프레서할로우드릴비트청소없이시공 앵커설치작업단계 Drill 2x2x2 Install Drill Install Drill Install 인발테스트 결과 HIT-V rod HIT-Z rod 100%* 100% ~ 30% 100% 내진성능! 안전성! 시공성! HY200 SAFEset 솔루션으로모두해결할수있습니다. 37
감사합니다! 38