LJ1220 Getting Started Guide-XL- EN,TC,ID,KO,TH,VI

getting started guide petunjuk untuk memulai penggunaan hp LaserJet 1220 print copy scan

Copyright Information Copyright Hewlett-Packard Company 2002 All Rights Reserved. Reproduction, adaptation, or translation without prior written permission is prohibited, except as allowed under the copyright laws. Part number: C7045-90922 First Edition: March 2002 FCC Regulations This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy. If this equipment is not installed and used in accordance with the instructions, it may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: Reorient or relocate the receiving antenna. Increase separation between equipment and receiver. Connect equipment to an outlet on a circuit different from that to which the receiver is located. Consult your dealer or an experienced radio/tv technician. Warranty The information contained in this document is subject to change without notice. Hewlett-Packard makes no warranty of any kind with respect to this information. HEWLETT-PACKARD SPECIFICALLY DISCLAIMS THE IMPLIED WARRANTY OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. Hewlett-Packard shall not be liable for any direct, indirect, incidental, consequential, or other damage alleged in connection with the furnishing or use of this information. Trademark Credits Microsoft, Windows, and Windows NT are U.S. registered trademarks of Microsoft Corporation. All other products mentioned herein may be trademarks of their respective companies. Any changes or modifications to the printer that are not expressly approved by HP could void the user s authority to operate this equipment. Use of a shielded interface cable is required to comply with the Class B limits of Part 15 of FCC rules. For more regulatory information, see the HP LaserJet 1220 electronic user guide.

Preparation 1 3 2 5 10 7 4 1 9 6 8 Review package contents. Make sure all parts are included. 1) HP LaserJet 1200 series printer. 2) Copier/scanner. 3) Copier/scanner media input tray. 4) Copier/scanner output bin. 5) Toner cartridge (in protective bag). 포장내용물확인. 부품이모두들어있는지확인합니다. 1) HP LaserJet 1200 시리즈프린터. 2) 복사기 / 스캐너. 3) 복사기 / 스캐너입력트레이. 4) 복사기 / 스캐너출력함. 5) 토너카트리지 ( 보호백에들어있음 ). Periksa isi kemasan. Pastikan semua bagian sudah lengkap. 1) Printer seri HP LaserJet 1200. 2) Perangkat penyalin (copier)/ perangkat penelusur (scanner). 3) Baki masukan untuk perangkat penyalin/ penelusur. 4) Keranjang keluaran untuk perangkat penyalin/penelusur. 5) Kartrid toner (dalam kantung pelindung). 6) Getting Started Guide. 7) Software and electronic user guide on two (2) CD-ROMs. 8) Power cord. 9) Printer media input tray. 10) Printer priority media input tray. 6) 입문설명서. 7) 소프트웨어및온라인사용설명서 CD-ROM 두장. 8) 전원코드. 9) 프린터용지함. 10) 프린터우선용지함. 6) Pedoman untuk Memulai Penggunaan. 7) Perangkat lunak dan petunjuk pemakaian elektronik (berbahasa Inggris) dalam dua (2) CD-ROM. 8) Kabel daya. 9) Baki masukan untuk printer. 10) Baki masukan prioritas utama untuk printer. English Bahasa Indonesia

2 3 416 mm (16.4 in.) 402 mm (15.8 in.) English Prepare the location. Place on a sturdy, level surface. Allow space for ventilation. Allow space behind the printer for output from the straight-through media doors. Regulate the environment. Do not place in direct sunlight. Ensure the environment is free from abrupt temperature or humidity changes. Temperature 10 to 32.5 C (50 to 91 F). Relative humidity 20% to 80%. 설치할장소를준비합니다. 견고하고평평한장소에프린터를놓습니다. 환기가잘될수있도록합니다. 고속출력배출구로부터용지가출력될수있도록프린터뒤쪽공간을비워둡니다. 배치환경선택. 직사광선에노출되지않도록합니다. 습도또는온도의급격한변화가없는환경이어야합니다. 온도 10 ~ 32.5 C. 상대습도 20 ~ 80% Bahasa Indonesia Siapkan lokasi penempatan. Tempatkan printer pada permukaan yang kuat dan datar. Sediakan cukup ruang untuk ventilasi. Sediakan juga cukup ruang di belakang printer untuk menampung hasil cetak dari pintu saluran-langsung keluaran. Atur keadaan ruangan. Jangan menempatkan perangkat sehingga terkena sinar matahari secara langsung. Pastikan bahwa tidak ada perubahan mendadak dalam suhu atau kelembapan ruangan. Suhu 10 sampai 32.5 C. Kelembapan relatif 20% sampai 80%.

Assembly 1 2 1 2 Open the toner door. Pull the sides of the door forward until the door locks in its open position. Leave the door open until step 10. Remove the left side panel. 1) Grasp the left side panel using the finger hole. 2) Pull out and remove the panel. 토너덮개열기. 덮개가열린위치에고정될때까지덮개양쪽을앞쪽으로당깁니다. 10 단계까지덮개를연채로둡니다. 왼쪽덮개를분리합니다. 1) 구멍을사용하여왼쪽덮개를잡습니다. 2) 덮개를당겨분리합니다. Buka pintu toner. Tarik ke depan bagian samping pintu sampai pintu tertahan pada posisi terbuka. Biarkan pintu terbuka sampai langkah 10. Lepaskan panel sebelah kiri. 1) Pegang panel dengan menggunakan lubang untuk jari. 2) Tarik ke arah keluar kemudian lepaskan panel.

3 4 English Install the copier/scanner. Place the copier/scanner unit on top of the printer. Firmly slide the copier/scanner towards the rear until it snaps into place. Attach the copier/scanner cable. Attach the ribbon cable to the edge of the I/O board. Make sure that the connection is secure. 복사기 / 스캐너케이블연결. 복사기 / 스캐너장치를프린터위에올려놓은복사기 / 스캐너가제자리에고정될때까지뒤쪽으로밉니다. 복사기 / 스캐너케이블연결. 리본케이블을 I/O 보드가장자리에연결합니다. 연결이제대로되었는지확인합니다. Bahasa Indonesia Pasang unit penyalin/penelusur. Tempatkan unit penyalin/penelusur di atas printer. Doronglah dengan kuat unit penyalin/penelusur ke arah belakang sampai terpasang baik pada tempatnya. Pasang kabel unit penyalin/penelusur. Sambungkan kabel pita ke ujung papan I/O. Pastikan kabel terpasang dengan kuat.

5 6 1 Connect USB or parallel cable to printer. The printer includes USB and parallel ports. Connect one cable to the proper port and run the cable through the cable slot. Do not connect the cable to the computer until step 16 (during software installation). Remove the scanner access cover from the left side panel. Pick up the left side panel and remove the scanner access cover (1) from the inside of the panel. Save the scanner access cover in case you remove the scanner. USB 또는병렬케이블을프린터에연결합니다. 프린터에는 USB 및병렬포트가포함되어있습니다. 케이블을알맞은포트에연결하고케이블슬롯을따라케이블을빼놓습니다. 단계 16 ( 소프트웨어를설치하는동안 ) 까지는케이블을컴퓨터에연결하지마십시오. 왼쪽패널에서스캐너액세스덮개를제거합니다. 왼쪽패널을들어올리고패널안쪽에서스캐너액세스덮개 (1) 을제거합니다. 스캐너를분리할경우를위해스캐너액세스덮개를잘보관합니다. Hubungkan USB atau kabel paralel ke printer. USB dan gerbang paralel tersedia pada printer ini. Sambungkan salah satu kabel ke gerbang yang sesuai dan tempatkan kabel melalui celahnya. Dilarang menghubungkan kabel ini ke komputer sebelum langkah ke 16 (dalam instalasi perangkat lunak) dilaksanakan. Lepaskan penutup akses scanner pada panel kiri. Ambil panel bagian kiri dan lepaskan penutup akses scanner (1) dari bagian dalam panel. Simpanlah penutup ini untuk digunakan jika anda ingin memindahkan perangkat ini.

7 8 1 2 English Reattach the left side panel. 1) Insert the left side panel tabs behind the edge of the front panel. 2) Swing the panel shut while pressing the top of the panel under the scanner. Prepare the toner cartridge. Remove the toner cartridge from the plastic bag. Remove the mylar tape by breaking the tab on the left and pulling the tape completely out. 왼쪽덮개를다시부착합니다. 1) 왼쪽덮개탭을전면덮개가장자리뒤로밀어넣습니다. 2) 스캐너아래덮개윗부분을누르면서덮개를닫습니다. 토너카트리지준비. 토너카트리지를플라스틱백에서꺼냅니다. 왼쪽의탭을떼어마일라테이프를분리하여테이프를완전히떼어냅니다. Bahasa Indonesia Pasang kembali panel sebelah kiri. 1) Sisipkan tonjolan-tonjolan panel ke belakang ujung panel depan. 2) Tutup panel dengan cara mengayunkannya sambil menekan bagian atas panel yang berada di bawah perangkat penelusur. Siapkan kartrid toner. Keluarkan kartrid toner dari kantung plastik. Lepaskan pita mylar dengan cara mematahkan tonjolan di sebelah kiri kemudian tariklah pita sampai keluar seluruhnya

9 10 Install the toner cartridge. Insert the cartridge into the printer, making sure that the toner cartridge is in position. Close the toner door. The toner cartridge engages when the door is closed. 토너카트리지설치. 토너카트리지를프린터에삽입하고올바로장착되었는지확인합니다. 토너덮개를닫습니다. 덮개가닫히면토너카트리지가맞물립니다. Pasang kartrid toner. Sisipkan kartrid ke dalam printer, pastikan kartrid toner terletak dengan baik di tempatnya. Tutup pintu toner. Kartrid toner akan terkunci jika pintu ditutup.

11 12 2 2 1 4 English Install the copier/scanner trays. 1) Insert the copier/scanner media output bin into the copier/scanner. 2) Insert the copier/scanner media input tray above the output bin. Install the printer trays. 1) Leave the printer media input trays taped together. 2) Slide the complete assembly in at an angle and then down until it fits securely in the printer. 3) Remove the tape and lift off the printer priority media input tray (top tray). 4) Slide the media guides out and back to accommodate the media. 복사기 / 스캐너용지함을설치합니다. 1) 복사기 / 스캐너출력함을복사기 / 스캐너에삽입합니다. 2) 복사기 / 스캐너입력트레이를출력함위에삽입합니다. 프린터용지함을설치합니다. 1) 프린터용지함은테이프로함께고정된채로두십시오. 2) 전체조립품을비스듬히밀어넣은다음프린터에단단히고정될때까지아래로내립니다. 3) 테이프를제거하고프린터우선용지함 ( 상단용지함 ) 을들어올립니다. 4) 용지에맞도록용지가이드를조절합니다. Bahasa Indonesia Pasang baki-baki perangkat penyalin/penelusur. 1) Sisipkan keranjang keluaran media ke unit penyalin/penelusur. 2) Sisipkan keranjang masukan media ke unit penyalin/penelusur. Pasang baki printer. 1) Biarkan baki-baki masukan media (kertas) printer terisolasi menjadi satu. 2) Selipkan masuk rakitan yang lengkap dalam posisi menyudut dan kemudian tekan ke bawah hingga tepat pada posisinya di printer. 3) Lepaskan isolasi dan angkat baki masukan media (kertas) prioritas utama printer (baki atas). 4) Gerakkan pemandu media cetak ke arah luar atau ke arah belakang agar media dapat ditempatkan dalam baki.

13 14 1 2 Load the media. 1) Place the media into the media input tray. Slide the guides until they are flush with the media. 2) Install the printer priority media input tray. 3) Connect the power cord. (220V models only: Turn on the switch.) Test the printer. Wait until the ready light is illuminated and press the Go button. A configuration page, showing the printer s current configuration, should print in 10 seconds. If a configuration page does not print, go to step 22. Refer to the User s Manual on the CD for more information. 용지를넣습니다. 1) 용지를용지함에넣습니다. 용지에맞도록가이드를조절합니다. 2) 프린터우선용지함을설치합니다. 3) 전원코드를연결합니다 (220V 모델은스위치를켭니다 ). 프린터테스트. 준비등이켜지기를기다렸다가진행단추를누릅니다. 프린터의현재구성을보여주는구성페이지가 10 초후에인쇄됩니다. 구성페이지가인쇄되지않으면단계 22로이동하십시오. 자세한정보를보려면 CD 의사용설명서를참조하십시오. Masukkan media (kertas). 1) Tempatkan media pada baki masukan tersebut. Dorong kembali pemandu media sampai rata dengan media. 2) Pasang baki masukan media (kertas) prioritas utama printer. 3) Sambungkan kabel daya. (Hanya untuk model 220V: Nyalakan saklarnya.) Lakukan pengujian perangkat penyalin. Tunggu sampai lampu siap (ready) menyala, kemudian tekan tombol Go. Satu halaman konfigurasi, yang menunjukkan konfigurasi yang berlaku pada printer, harus tercetak dalam waktu 10 detik. Apabila halaman konfigurasi tidak tercetak, lanjutkan ke langkah 22. Aculah pada Buku Panduan Pengguna yang terdapat pada CD untuk memperoleh keterangan lebih lanjut.

15 16 English Test the copier. Place a document in the copier/scanner input tray, and press the Copy button. The document should feed into the copier/scanner. A copy should appear in the printer output bin. If no copy appears, go to step 23 (Troubleshooting the copier). Install the printer software. Choose and install the appropriate CD for your software installation or go to the Plug and Play section. Use CD #1 for Windows (step 17) or CD #2 for Macintosh (step 18). Make sure to select the correct model number during installation (HP 1220 for printer with copier/scanner; HP 1200 for printer only). 복사기테스트. 복사기 / 스캐너입력트레이에문서를놓고복사단추를누릅니다. 문서가복사기 / 스캐너로들어가고, 복사본이프린터출력함으로출력되어야합니다. 복사본이나타나지않으면단계 23( 복사기문제해결 ) 으로이동하십시오. 프린터소프트웨어설치. 소프트웨어설치를위해해당 CD 를선택하여설치하거나플러그앤플레이섹션으로이동합니다. Windows 용 CD #1( 단계17) 또는 Macintosh 용 CD #2 ( 단계 18) 를사용하십시오. 설치시반드시올바른모델번호를선택해야합니다 ( 복사기 / 스캐너기능을가진프린터의경우 HP 1220, 프린터전용인경우 HP 1200). Bahasa Indonesia Lakukan pengujian perangkat penyalin. Tempatkan dokumen pada baki masukan perangkat penyalin/penelusur kemudian tekan tombol Copy. Dokumen akan masuk ke dalam perangkat penyalin/penelusur. Salinannya akan muncul di keranjang keluaran printer. Apabila tidak ada salinan yang ke luar, lanjutkan ke langkah 23 (Penelusuran Masalah copier). Instal perangkat lunak printer. Pilih dan masukkan CD yang tepat untuk instalasi perangkat lunak anda atau baca pada bab Plug and Play. Gunakan CD nomor 1 untuk Windows (langkah 17) atau CD nomor 2 untuk Macintosh (langkah 18). Pastikan untuk memilih nomor model yang sesuai ketika melakukan instalasi (HP 1220 untuk printer dengan copier/scanner; HP 1200 untuk printer saja).

17 Installing on Windows. 1) Select Software Installation from the autorun screen. If autorun does not occur, select Start, select Run, and type x:\setup (where x is the letter of your CD-ROM drive). 2) Follow the instructions on the screen. Click Finish to complete the installation. 3) After the installation is complete, connect the I/O cable to the computer and reboot the computer. Windows 상의설치. 1) 자동실행화면에서소프트웨어설치를선택합니다. 자동실행이시작되지않으면시작, 실행을선택한다음 x:\setup (x 는 CD-ROM 드라이브문자 ) 을입력합니다. 2) 화면에나타나는지시사항을따릅니다. 종료를눌러설치를완료합니다. 3) 설치를완료한후 I/O 케이블을컴퓨터에연결하고컴퓨터를재부팅합니다. Instalasi pada Windows. 1) Pilih Instalasi Perangkat Lunak dari layar yang diperintah secara otomatis. Jika layar autorun tidak muncul, pilih Start, pilih Run, kemudian ketikkan x:\setup (di mana x adalah huruf pengenal penggerak CD-ROM anda). 2) Ikuti petunjuk pada layar. Klik Finish untuk menyelesaikan instalasi 3) Setelah instalasi selesai, sambungkan kabel I/O ke komputer dan boot ulang komputer.

18 English Installing on Macintosh (USB). 1) Connect the I/O cable to the computer. 2) Insert CD #2. 3) Double-click the HP All-in-One Installer. 4) Select a language. 5) Click Install, and follow the screen instructions. 6) When the installation is complete, click Restart. 7) When the computer restarts, follow the onscreen instructions for the HP All-in-One Setup Utility. 8) Click Finish to complete the setup. Macintosh 에설치하기 (USB). 1) I/O 케이블을컴퓨터에연결합니다. 2) CD #2 를삽입합니다. 3} HP All-in-One 설치기를두번누릅니다. 4) 언어를선택합니다. 5) 설치를누른다음화면에나타나는지침을따릅니다. 6) 설치가완료되면다시시작을누릅니다. 7) 컴퓨터가재시작되면 HP All-in-One 설치유틸리티화면에나타나는지시를따르십시오. 8) 설치를끝내려면완료를누릅니다. Bahasa Indonesia Melakukan Instalasi pada Macintosh (USB). 1) Sambungkan kabel I/O ke komputer. 2) Masukkan CD nomor 2. 3) Klik dua kali HP All-in-One Installer (Pemasang HP Lengkap). 4) Pilih bahasa yang dikehendaki. 5) Klik Install kemudian ikuti petunjuk pada layar. 6) Bilamana instalasi telah selesai, klik Restart. 7) Ketika komputer memulai lagi, ikuti petunjuk-petunjuk yang ada pada layar untuk HP All-in-One Setup Utility (Perangkat Penyetelan HP Lengkap). 8) Klik Finish untuk mengakhiri penyetelan

19 20 Test the scanner. 1) Place a document in the copier/scanner input tray and press the Scan button. The HP LaserJet Director appears on your screen. Note: NT 4.0 users can access HP LaserJet Director through Start\Programs\HP 1220\HP LaserJet Director. 1) Click Scan, and select your printer from the Destination field. 2) Click OK. The document should feed into the copier/scanner. The copy should appear in the printer output bin. If no copy appears, go to Step 23 (Troubleshooting the copier). 스캐너테스트. 복사기 / 스캐너입력트레이에문서를놓고스캔단추를누릅니다. HP LaserJet Director 가화면에나타납니다. 주 : NT 4.0 사용자는시작 \ 프로그램 \HP 1220\ HP LaserJet 디렉터를통하여 HP LaserJet 디렉터에액세스할수있습니다. 1) 스캔을누른다음대상필드에서사용할프린터를선택합니다. 2) 확인을누릅니다. 문서가복사기 / 스캐너로들어가고, 복사본이프린터출력함으로출력되어야합니다. 복사본이나타나지않으면단계 23 ( 복사기문제해결 ) 으로이동하십시오. Lakukan pengujian perangkat penelusur. Tempatkan dokumen pada baki masukan perangkat penyalin/penelusur kemudian tekan tombol Scan. Pada layar akan muncul HP LaserJet Director. Catatan: Para pengguna NT 4.0 dapat mengakses HP LaserJet Director melalui Start\Programs\HP 1220\HP LaserJet Director. 1) Klik Scan, kemudian pilih printer anda dari field Destination. 2) Klik OK. Dokumen akan masuk ke dalam perangkat penyalin/penelusur. Salinannya akan muncul di keranjang keluaran printer. Apabila tidak ada salinan yang ke luar, lanjutkan ke Langkah 23 (Penelusuran Masalah copier).

21 22 No lights are on. English Congratulations! Your HP LaserJet 1220 product is ready to use. If you had any problems, refer to the electronic user guide for troubleshooting information as well as service and support information. Troubleshooting the printer. 1) If no lights are on, check the power cord, and then press the Go button. 축하합니다! HP LaserJet 1220 을사용할준비가되었습니다. 문제가발생할경우서비스및지원정보는물론문제해결정보에관해온라인사용설명서를참조하십시오. 프린터문제해결. 1) 표시등이켜지지않으면전원코드를확인하고진행단추를누릅니다. Bahasa Indonesia Selamat! Product HP LaserJet 1220 anda kini sudah siap digunakan. Apabila anda mempunyai masalah apapun, aculah pada buku panduan pengguna elektronis untuk memperoleh keterangan tentang penelusuran masalah dan juga keterangan tentang servis dan dukungan. Jika printer tidak berfungsi baik. 1) Jika tidak ada lampu yang menyala, periksa kabel daya, kemudian tekan tombol Go.

All lights are blinking. Bottom light is blinking. All lights are on. 2) If the bottom light is blinking, check the toner cartridge for proper installation, put media in the input tray, make sure all doors are closed, or check for media jams. 3) If all lights are blinking, remove the DIMM and replace it with a new DIMM, if necessary. 4) If all lights are on, unplug the printer, wait 5 minutes, plug it back in, and retry. If errors still exist, call HP Customer Support. 2) 아래쪽표시등이깜빡이면토너카트리지가올바로설치되었는지확인하고, 용지를용지함에넣은다음, 모든덮개가닫혀있는지확인하고, 용지걸림을확인합니다. 3) 모든표시등이깜빡이면 DIMM 을분리하고필요한경우새로운 DIMM 으로교체합니다. 4) 모든표시등이켜지면프린터의코드를뽑고 5 분정도기다렸다가다시코드를꽂고재시도해봅니다. 오류가지속되면 HP 고객지원으로문의합니다. 2) Jika lampu bawah berkedip-kedip, periksa apakah kartrid toner sudah terpasang dengan baik, apakah media cetak sudah tersedia di baki masukan, apakah semua pintu sudah tertutup dengan baik, atau apakah ada kemacetan media cetak. 3) Jika semua lampu berkedip-kedip, lepaskan DIMM dan gantilah dengan DIMM yang baru jika perlu. 4) Jika semua lampu menyala, lepaskan kabel daya dari printer, tunggu 5 menit, pasang kembali kabel daya ke printer, kemudian ulangi pengujian. Jika masalah masih belum hilang, hubungi Layanan Bantuan HP.

23 English Troubleshooting the copier. 1) Check the configuration page (step 14) to verify that the copier/scanner is recognized. 2) If it is recognized, retry the copier test (step 15). 3) If the copier/scanner is not recognized, verify that the copier/scanner cable is firmly connected. 4) Unplug the printer, plug the printer back in, and retry the test. If errors still exist, call HP Customer Support. 복사기문제해결. 1) 복사기 / 스캐너가인식되었는지점검하려면구성페이지 ( 단계 14) 를확인하십시오. 2) 복사기가인식되었으면복사기검사 ( 단계 15) 를재시도합니다. 3) 복사기 / 스캐너가인식되지않았으며복사기 / 스캐너케이블이제대로연결되었는지확인합니다. 4) 프린터의플러그를뽑았다가다시꽂고테스트를재시도합니다. 오류가지속되면 HP 고객지원으로문의합니다. Bahasa Indonesia Jika perangkat penyalin tidak berfungsi baik. 1) Periksa halaman konfigurasi (langkah 14) untuk memastikan bahwa copier/scanner dikenali. 2) Apabila tidak dikenali, coba ulangi uji copier (langkah 15). 3) Jika unit penyalin/penelusur tersebut belum dikenali, periksa apakah kabel unit tersebut sudah tersambung dengan baik. 4) Lepaskan kabel daya dari printer, pasang kembali, kemudian ulangi pengujian. Jika masalah masih belum hilang, hubungi Layanan Bantuan HP.

Plug & Play 1 Installing on Windows 98 and Millennium (USB). 1) Connect the I/O cable to the computer. 2) Reboot the computer. 3) In the Add New Hardware wizard, click Next. 4) Select Search for the best driver for your device (recommended), and click Next. 5) Select Specify a location, and type x:\98me_usb\ (where x is the letter of your CD-ROM drive). 6) Follow the instructions on your screen. Windows 98/Millennium 에설치 (USB). 1) I/O 케이블을컴퓨터에연결합니다. 2) 컴퓨터를재시동합니다. 3) 새하드웨어추가마법사에서다음을누릅니다. 4) 장치에가장알맞은드라이버검색 ( 권장 ) 을선택하고다음을누릅니다. 5) 검색할위치지정을선택하고 x:\98me_usb\ (x 는 CD-ROM 드라이브문자 ) 를입력합니다. 6) 화면에나타나는지시사항을따릅니다. Melakukan Instalasi pada Windows 98 dan Millennium (USB). 1) Hubungkan kabel I/O ke komputer. 2) Reboot komputer anda. 3) Pada wizar Add New Hardware, klik Next. 4) Pilih Search for the best driver for your device (recommended) kemudian klik Next. 5) Beri tanda pada Specify a location, kemudian ketikkan x:\98me_usb\ (di mana x adalah penggerak CD-ROM anda). 6) Ikuti petunjuk pada layar.

2 English Installing on Windows 2000 (USB). 1) Connect the I/O cable to the computer. 2) Reboot the computer. 3) In the Found New Hardware wizard, click Next. 4) Select Search for a suitable driver for my device (recommended), and click Next. 5) Select Specify a location. 6) Under Copy manufacturer s files from, type x:\2000\ (where x is the letter of your CD-ROM drive), and click OK. 7) Click Next. 8) Follow the instructions on your screen. Windows 2000에설치 (USB). 1) I/O 케이블을컴퓨터에연결합니다. 2) 컴퓨터를재시동합니다. 3) 새하드웨어발견마법사에서다음을누릅니다. 4) 장치에적절한드라이버검색 ( 권장 ) 을선택하고다음을누릅니다. 5) 위치지정을선택합니다. 6) 복사할제조업체파일위치 : 에서 x:\2000\ (x 는 CD-ROM 드라이브문자 ) 를입력하고, 확인을누릅니다. 7) 다음을누릅니다. 8) 화면에나타나는지시사항을따릅니다. Bahasa Indonesia Melakukan Instalasi pada Windows 2000 (USB). 1) Hubungkan kabel I/O ke komputer. 2) Reboot komputer anda. 3) Pada wizar Found New Hardware, klik Next. 4) Pilih Search for a suitable driver for my device (recommended) kemudian klik Next. 5) Beri tanda pada Specify a location. 6) Di bawah Copy manufacturer s files from, ketikkan x:\2000\ (di mana x adalah penggerak CD-ROM anda) kemudian klik OK. 7) Klik Next. 8) Ikuti petunjuk pada layar.

3 Installing on Windows 9X and Millennium (Parallel). 1) Connect the I/O cable to the computer. 2) Reboot the computer. 3) When the Installation wizard appears, click Next. 4) Select Search for the best driver for your device (recommended), and click Next. 5) Select Specify a location, then type x:\9xme_lpt\ (where x is the letter of your CD-ROM drive). 6) Follow the instructions on your screen. Windows 9X/Millennium 에설치 ( 병렬 ). 1) I/O 케이블을컴퓨터에연결합니다. 2) 컴퓨터를재시동합니다. 3) 설치마법사가나타나면다음을누르십시오. 4) 장치에가장알맞은드라이버검색 ( 권장 ) 을선택하고다음을누릅니다. 5) 검색할위치지정을선택하고 x:\9xme_lpt\ (x 는 CD-ROM 드라이브문자 ) 를입력합니다. 6) 화면에나타나는지시사항을따릅니다. Melakukan Instalasi pada Windows 98 dan Millennium (Paralel). 1) Hubungkan kabel I/O ke komputer. 2) Reboot komputer anda. 3) Bilamana petunjuk Instalasi muncul, klik Next. 4) Pilih Search for the best driver for your device (recommended) kemudian klik Next. 5) Beri tanda pada Specify a location, kemudian ketikkan x:\9xme_lpt\ (di mana x adalah penggerak CD-ROM anda). 6) Ikuti petunjuk pada layar.

4 5 English Installing on Windows NT (Parallel). (Note: You must have Administrator privileges.) 1) When the Installation wizard appears, click Software Installation. 2) Follow the instructions on your screen. Installing on Windows 2000 (Parallel). 1) Connect the I/O cable to the computer. 2) Reboot the computer. 3) In the Found New Hardware wizard, click Next. 4) Select Search for a suitable driver for my device (recommended), and click Next. Windows NT 에설치 ( 병렬 ). ( 참고 : 관리자권한이있어야합니다.) 1) 설치마법사가나타나면소프트웨어설치를누르십시오. 2) 화면에나타나는지시사항을따릅니다. Windows 2000에설치 ( 병렬 ). 1) I/O 케이블을컴퓨터에연결합니다. 2) 컴퓨터를재시동합니다. 3) 새하드웨어발견마법사에서다음을누릅니다. 4) 장치에적절한드라이버검색 ( 권장 ) 을선택하고다음을누릅니다. Bahasa Indonesia Melakukan Instalasi pada Windows NT (Paralel). (Perhatikan: Anda harus memiliki hak (privilege) sebagai administrator ) 1) Bilamana petunjuk Instalasi muncul, klik Software Installation. 2) Ikuti petunjuk pada layar. Melakukan Instalasi pada Windows 2000 (Paralel). 1) Hubungkan kabel I/O ke komputer. 2) Reboot komputer anda. 3) Pada wizar Found New Hardware, klik Next. 4) Pilih Search for a suitable driver for my device (recommended) kemudian klik Next.

5) Select Specify a location. 6) Under Copy manufacturer s files from, type x:\2000\ (where x is the letter of your CD-ROM drive), and click OK. 7) Click Next. 8) Follow the instructions on your screen. 5) 위치지정을선택합니다. 6) 복사할제조업체파일위치 : 에서 x:\2000\ (x 는 CD-ROM 드라이브문자 ) 를입력하고, 확인을누릅니다. 7) 다음을누릅니다. 8) 화면에나타나는지시사항을따릅니다. 5) Beri tanda pada Specify a location. 6) Di bawah Copy manufacturer s files from, ketikkan x:\2000\ (di mana x adalah penggerak CD-ROM anda) kemudian klik OK. 7) Klik Next. 8) Ikuti petunjuk pada layar.

printed on recycled paper copyright 2002 Hewlett-Packard Co. www.hp.com/support/lj1220 *C7045-90922* *C7045-90922* C7045-90922