Chager 충전기 UC 36YRL Handling instructions 사용설명서 Read through carefully and understand these instructions before use. 사용전본설명서를충분히읽고이해한후사용해주십시오.
1 2 1 9 4 3 7 6 8 5 English 한국어 1 Rechargeable battery (BSL2530) 재충전배터리 (BSL2530) 2 Rechargeable battery (BSL3626) 재충전배터리 (BSL3626) 3 Charge status lamp (red) 충전상태램프 ( 적색 ) 4 Overheat lamp (green) 과열램프 ( 녹색 ) 5 Rail for connecting the rechargeable battery 6 Cooling fan 쿨링팬 7 Caution plate 경고판 충전식배터리연결용레일 8 Name plate 네임플레이트 9 Line 라인 2
English GENERAL OPERATIONAL PRECAUTIONS 1. Keep work area clean. Cluttered areas and benches invite accidents. 2. Avoid dangerous environment. Don t expose power tools and charger to rain. Don t use power tools and charger in damp or wet locations. And keep work area well lit. Never use power tools and charger near fl ammable or explosive materials. Do not use tool and charger in presence of fl ammable liquids or gases. 3. The appliance is not intended for use by young children or infi rm persons without supervision. Young children should be supervised to ensure that they do not play with the appliance. All visitors should be kept safe distance from work area. 4. Store idle tools and charger. When not in use, tools and charger should be stored in dry, high or lockedup place out of reach or children. Store tools and charger in a place in which the temperature is less than 40 C. 5. Don t abuse cord. Never carry charger by cord or yank it to disconnect from receptacle. Keep cord from heat, oil and sharp edges. 6. When the charger is not in use or when being maintained and inspected, disconnect the power cord of the charger from the receptacle. 7. To avoid danger, always use only the specifi ed charger. 8. Use only genuine HITACHI replacement parts. 9. Do not use power tools and charger for applications other than those specifi ed in the Handling Instructions. 10. To avoid personal injury, use only the accessories or attachment recommended in these handling instructions or in the HITACHI catalog. 11. If the supply cord is damaged, it must be replaced by the manufacture or its service agent or a similarly qualifi ed person in order to avoid a hazard. Let only the authorized service center do the repairing. The Manufacture will not be responsible for any damages or injuries caused by repair by the unauthorized persons or by mishandling of the tool. 12. To ensure the designed operational integrity of power tools and charger, do not remove installed covers or screws. 13. Always use the charger at the voltage specifi ed on the nameplate. 14. Always charge the battery before use. 15. Never use a battery other than that specifi ed. Do not connect a usual dry cell, a rechargeable battery other than that specifi ed or a car battery to the power tool. 16. Do not use a transformer containing a booster. 17. Do not charge the battery from an engine electric generator or DC power supply. 18. Always charge indoors. Because the charger and battery heat slightly during charging, charge the battery in a place not exposed to direct sunlight; where the humidity is low and the ventilation is good. 19. Use the exploded assembly drawing on this handling instructions only for authorized servicing. PRECAUTIONS FOR CHARGER 1. Always charge the battery at an ambient temperature of 0 40 C. A temperature of less than 0 C will result in over charging which is dangerous. The battery cannot be charged at a temperature greater than 40 C. The most suitable temperature for charging is that of 20 25 C. 2. Do not use the charger continuously. When one charging is completed, leave the charger for about 15 minutes before the next charging of battery. 3. Do not allow foreign matter to enter the connector for the rechargeable battery. 4. Never disassemble the rechargeable battery or charger. 5. Never short-circuit the rechargeable battery. Short-circuiting the battery will cause a great electric current and overheat. It results in burn or damage to the battery. 6. Do not dispose of the battery in fi re. If the battery is burnt, it may explode. 7. Using an exhausted battery will damage the charger. 8. Bring the battery to the shop from which it was purchased as soon as the post-charging battery life becomes too short for practical use. Do not dispose of the exhausted battery. 9. Do not insert objects into the air ventilation slots of the charger. Inserting metal objects or fl ammable into the charger air ventilation slots will result in an electrical shock hazard or damage to the charger. 3
English SPECIFICATION CHARGER Charging time Charging voltage Weight BSL2530: Approx. 60 minutes BSL3626: Approx. 80 minutes 25.2 36 V 0.9 kg APPLICATION For charging the HITACHI BATTERY. BSL2530, BSL3626 CHARGING Before using the power tool, charge the battery as follows. 1. Connect the charger s power cord to the receptacle. When connecting the plug of the charger to a receptacle, the charge status lamp will blink in red. (At 1-second intervals). 2. Insert the battery into the charger. Firmly insert the battery into the charger until the line is visible, as shown in Fig. 1. 3. Charging When inserting a battery in the charger, the charge status lamp will light up continuously in red. When the battery becomes fully recharged, the charge status lamp will blink in red. (At 1-second intervals.) (See Table 1) (1) Lamp indication The indications of the lamp will be as shown in Table 1, according to the condition of the charger or the rechargeable battery. Table 1 Before charging Blinks Indications of the lamp Lights for 0.5 seconds. Does not light for 0.5 seconds. (off for 0.5 seconds) Charge status lamp (red) While charging Charging complete Lights Blinks Lights continuously Lights for 0.5 seconds. Does not light for 0.5 seconds. (off for 0.5 seconds) Charging impossible Flickers Lights for 0.1 seconds. Does not light for 0.1 seconds. (off for 0.1 seconds) Malfunction in the battery or the charger Overheat lamp (green) Overheat standby Lights Lights continuously NOTE: When standby for cooling battery, UC36YRL cools the overheated battery by cooling fan. Battery overheated. Unable to charge. (Charging will commence when battery cools) (2) Regarding the temperature of the rechargeable battery. The temperatures for rechargeable batteries are as shown in the Table 2, and batteries that have become hot should be cooled for a while before being recharged. Table 2 Rechargeable batteries Temperatures at which the battery can be recharged BSL2530, BSL3626 0 C 50 C (3) Regarding recharging time Table 3 shows the recharging time required according to the type of battery. Table 3 Recharging time (approx. min.) at 20 C Battery capacity (Ah) Battery Li-ion BATTERY Voltage 2.6 Ah 3.0 Ah 25.2 V BSL2530 (14 cells) 65 min. 36 V BSL3626 (20 cells) 80 min. NOTE: The recharging time may vary according to the ambient temperature. 4. Disconnect the charger s power cord from the receptacle. 5. Hold the charger fi rmly and pull out the battery. NOTE Be sure to pull out the battery from the charger after use, and then keep it. 4
English Regarding electric discharge in case of new batteries, etc. As the internal chemical substance of new batteries and batteries that have not been used for an extended period is not activated, the electric discharge might be low when using them the fi rst and second time. This is a temporary phenomenon, and normal time required for recharging will be restored by recharging the batteries 2 3 times. How to make the batteries perform longer. (1) Recharge the batteries before they become completely exhausted. When you feel that the power of the tool becomes weaker, stop using the tool and recharge its battery. If you continue to use the tool and exhaust the electric current, the battery may be damaged and its life will become shorter. (2) Avoid recharging at high temperatures. A rechargeable battery will be hot immediately after use. If such a battery is recharged immediately after use, its internal chemical substance will deteriorate, and the battery life will be shortened. Leave the battery and recharge it after it has cooled for a while. CAUTION If the battery is charged while it is heated because it has been left for a long time in a location subject to direct sunlight or because the battery has just been used, the overheat lamp of the charger lights up green. In such a case, fi rst let the battery cool, then start charging. When the charge status lamp fl ickers in red (at 0.2-seconds intervals), check for and take out any foreign objects in the charger s battery connector. If there are no foreign objects, it is probable that the battery or charger is malfunctioning. Take it to your authorized Service Center. Since the built-in micro computer takes about 3 seconds to confi rm that the battery being charged with UC36YRL is taken out, wait for a minimum of 3 seconds before reinserting it to continue charging. If the battery is reinserted within 3 seconds, the battery may not be properly charged. CAUTION Repair, modifi cation and inspection of Hitachi Power Tools must be carried out by a Hitachi Authorized Service Center. This Parts List will be helpful if presented with the tool to the Hitachi Authorized Service Center when requesting repair or other maintenance. In the operation and maintenance of power tools, the safety regulations and standards prescribed ineach country must be observed. MODIFICATIONS Hitachi Power Tools are constantly being improved and modifi ed to incorporate the latest technological advancements. Accordingly, some parts (i.e. code numbers and/ ordesign) may be changed without prior notice. NOTE Due to HITACHI s continuing program of research and development, the specifi cations herein are subject to change without prior notice. MAINTENANCE AND INSPECTION 1. Inspecting the mounting screws: Regularly inspect all mounting screws and ensure that they are properly tightened. Should any of the screws be loose, retighten them immediately. Failure to do so could result in serious hazard. 2. Cleaning of the charger When the charger is stained, wipe with a soft dry cloth or a cloth moistened with soapy water. Do not use chloric solvents, gasoline or paint thinner, for they melt plastics. 3. Store idle charger When not in use, the charger should be stored in dry, high or locked-up place out of reach of children. 4. Service parts list A : Item No. B : Code No. C : No. Used D : Remarks 5
안전을위한일반사용수칙 1. 작업환경을깨끗하게하십시오. 작업장, 작업대가어지러우면사고를가져올수있습니다. 2. 위험한장소를피하십시오. 파워툴, 충전기를비에노출시키지마십시오. 파워툴, 충전기를습한장소에서사용하지마십시오. 작업장을밝게하십시오. 가연성물질옆에서파워툴, 충전기를사용하지마십시오. 가연성액체, 가스옆에서사용하지마십시오. 3. 본장치는어린이, 심신미약자가감독없이사용할수없습니다. 어린이가본장치를가지고놀지않도록주의감독해주십시오. 작업반경내사람들의안전거리를유지하십시오. 4. 사용하지않는도구, 충전기는보관하십시오. 사용하지않으실때는도구와충전기는건조하고어린이의손이닿지않는곳에보관하십시오. 40 이하의온도에서보관하십시오. 5. 코드가망가지지않도록하십시오. 줄을잡아당겨서플러그를빼지마십시오. 열, 기름, 날카로운물건을피하여보관해주십시오. 6. 충전기를사용하지않거나보관할때, 검사할때는충전기의파워코드를콘센트에서빼주십시오. 7. 위험을방지하기위하여, 명시된충전기만사용하십시오. 8. 정품 HITACHI 부품만사용하십시오. 9. 본사용설명서에명시되지않은파워툴, 충전기를사용하지마십시오. 10. 상해를예방하기위하여, 본사용설명서혹은 HITACHI 카탈로그에서추천된액세서리, 부품을사용하여주십시오. 11. 공급코드가망가지면제조자, 서비스에이전트혹은관련기술자에게교체하십시오. 공식서비스센터만수리할수있습니다. 제조사는비공식서비스센터의수리, 부주의로인한손해, 상해에대해책임지지않습니다. 12. 파워툴과충전기가온전히작동할수있도록설치된커버와스크류를제거하지마십시오. 13. 네임플레이트에명시된볼트의충전기를사용하십시오. 14. 사용전항상배터리를충전하십시오. 15. 명시된배터리이외에사용하지마십시오. 건전지, 명시되지않은재충전배터리, 자동차배터리에연결하지마십시오. 16. 승압변압기를사용하지마십시오. 17. 엔진전기발전기, DC 전원장치로충전하지마십시오. 18. 항상실내에서충전하십시오. 충전하는동안약간의열이발생합니다. 햇빛에노출되지않는곳에서충전하십시오. 습기가적고, 통풍이잘되는곳에서충전하십시오. 19. 본설명서의조립도는공인된서비스용으로만사용해주십시오. 충전기의안전예방수칙 1. 항상 0-40 사이의적절한온도에서충전하십시오. 0 이하에서는과도하게충전되어위험할수있습니다. 40 이상에서는충전되지않습니다. 가장적절한충전온도는 20-25 사이입니다. 2. 충전기를연속적으로사용하지마십시오. 한번충전이끝나면, 다음충전때까지 15 분정도기다리십시오. 3. 재충전배터리와충전기의연결홀에이물질이들어가지않도록하십시오. 4. 재충전배터리, 충전기를분해하지마십시오. 5. 재충전배터리가합선되지않도록하십시오. 전류의증가및과열로인해배터리가손상됩니다. 6. 배터리를불속에버리지마십시오. 배터리가타면폭발할수있습니다. 7. 소모된배터리를사용하시면충전기가망가질수있습니다. 8. 사용중배터리의수명이짧아지면배터리를구매처로가져가십시오. 소모된배터리를버리지마십시오. 9. 충전기의통풍구에이물질을넣지마십시오. 금속성물질이나가연성물질을충전기의통풍구로넣으면전기충격의위험이있을수있으며배터리가망가질수있습니다. 사양 충전기 충전시간 충전전압무게 BSL2530: 약 60 분 BSL3626: 약 80 분 25.2 V - 36 V 0.9 Kg 적용 HITACHI 배터리충전용 BSL2530, BSL3626 충전 파워툴을사용하기전에아래의순서대로배터리를충전해주십시오. 1. 충전기의전원코드를소켓에연결하십시오. 소켓에충전기의플러그를연결할때, 충전상태램프의빨간불이깜빡입니다. (1 초간격 ) 2. 배터리를충전기에삽입합니다. Fig. 1 와같이선이보일때까지배터리를충전기안에정확히삽입하십시오. 3. 충전충전배터리를충전기안에삽입할때, 충전상태를나타내는램프의빨간불이계속켜집니다. 배터리가완전히재충전되면, 충전상태램프의빨간불이깜빡입니다. (1 초간격 ) ( 표 1 참조 ) (1) 램표표시충전기, 재충전배터리의상태에따른램프표시는아래와같습니다. 6
표 1 파일롯램프표시 0.5초간격으로점멸 충전전 점멸 충전상태램프 ( 적색 ) 충전중 충전완료 점등 점멸 계속불이켜져있음 0.5초간격으로점멸 충전불가 점멸 0.1 초간격으로점멸 배터리나충전기의오작동 과열램프 ( 녹색 ) 과열준비 점등 배터리과열계속불이켜져있음충전할수없음 ( 배터리가식으면다시충전됨 ) 주의 : 배터리가식을때까지기다릴때, UC36YRL은과열된배터리를냉각팬으로식힙니다. (2) 재충전온도재충전배터리의온도는표 2 와같습니다. 과열된배터리는재충전전충분히식힌후사용해야합니다. 표 2. 재충전배터리 재충전가능한온도 BSL2530, BSL3626 0 C - 50 C (3) 재충전시간 배터리타입에따른재충전시간은표3과같습니다. 표3. 재충전시간 ( 근사치, 분 ) 20 배터리용량 (Ah) 배터리 Li-ion 배터리 전압 2.6 Ah 3.0 Ah 25.2 V --- --- BSL2530 (14 셀 ) 60분 36 V BSL3626 (20 셀 ) 80분 --- --- 주의 : 재충전시간은온도에따라달라질수있습니다. 4. 충전기의파워코드를소켓에서빼주십시오. 5. 충전기를잡고배터리를빼주십시오. 주의사용후배터리를충전기에서분리하여보관하십시오. 새배터리의방전 새배터리, 혹은오랫동안사용하지않은배터리의내부화학현상에따라처음한두번성능이떨어질수있습니다. 이것은일시적인현상이며 2-3 회재충전하시면회복됩니다. 배터리수명을길게하려면 (1) 배터리가완전히소모되기전에재충전하십시오. 공구의파워가약해졌다고느끼면사용을멈추고재충전하십시오. 계속해서사용할경우배터리가망가지거나수명이짧아질수있습니다. (2) 고온에서의재충전은피하십시오. 재충전배터리는사용즉후과열됩니다. 이상태에서재충전으로하면내부화학물질이망가지고수명이짧아집니다. 배터리를식힌후재충전하십시오. 주의 배터리를장시간햇빛에노출시키거나장시간사용에의해과열된상태에서충전하는경우, 충전기의과열램프의녹색불이들어옵니다. 이경우, 배터리를식힌후충전하십시오. 충전상태램프의빨간불이깜박이면 (0.2 초간격 ) 배터리커넥터에이물질이없는지체크후제거해주십시오. 이물질이없는경우, 배터리나충전기의오작동입니다. 공인서비스센터에문의하십시오. 내장마이크로컴퓨터가 UC36YRL 에서배터리가충전이완료된것을확인하는데 3 초가걸립니다. 연속적으로충전할때재삽입전최소 3 초기다려주십시오. 배터리가 3 초이내재삽입되면배터리는제대로충전되지않은것입니다. 유지보수및검사 1. 스크류검사정기적으로모든스크류가잘조여져있는지검사하고확인하십시오. 스크류가느슨해진경우즉시조여주십시오. 그렇지않으면큰위험을초래할수있습니다. 2. 충전기청소충전기가녹슨경우부드러운마른천이나비눗물을묻힌천으로닦아주십시오. 염소계솔벤트, 가솔린, 페인트신나는플라스틱을녹이므로사용하지마십시오. 3. 사용하지않는충전기는보관하십시오. 충전기를사용하지않는경우, 건조하고어린이의손이닿지않는높은곳에보관하십시오. 7
4. 서비스부품정보 A: 품목번호 B: 코드번호 C: 사용개수 D: 비고주의 Hitachi 전동툴의수리, 변경및검사는반드시공식 Hitachi 서비스센터를통해서해야합니다. 공식 Hitachi 서비스센터에수리또는기타점검을요청할때툴과함께부품정보를제공하면도움이됩니다. 전동툴을사용하거나점검할때는각국의안전수칙및규정을준수해야합니다. 변경 Hitachi 전동툴은개선및수정을통해끊임없이최신기술발전을반영하고있습니다. 따라서일부부품 ( 코드번호및 / 또는디자인 ) 은사전예고없이변경될수있습니다. 주의 HITACHI 의연구개발프로그램에의해본사용설명서의규격은사전안내없이변경될수있습니다. 8
UC36YRL A B C D 1 328637 1 2 328630 1 3 993963 3 M3 12 4 327174 7 D3 8 5 328632 1 6 949553 3 M3 7 1 8 328633 1 9 328622 1 10 328618 1 11 326358 4 D3 18 12 327173 4 13 1 14 322201 1 15 327176 1 16 328531 1 17 328679 1 18 1 19 327175 2 D3 25 20 326809 1 9
10
11
Hitachi Koki Co., Ltd. 105 Code No. C99165451 G Printed in China