3-1. Disassembly and Reassembly R510 [Caution] Attention to red sentence. 2 2 1. Before disassembling, the AC adaptor and Battery must be separated. 2. AS mark No.1/2 put KNOB-Battery to end of each side, then pull the battery upward like outward 1 1 3. After removing the Battery 4. ODD and DOOR-HDD, DOOR-Memory Screw Remove. M2 X L4, Black (4EA) - Yellow ( ): ODD Screw - Skyblue ( ): HDD Door Screw - Red ( ): Minicard Door Screw 5. HDD DOOR Remove, MEMORY DOOR Remove ODD Remove 3-1 3_Disassembly and Reassembly_eng1 1
6. Separate HDD by pulling in the arrow direction. * Cautions Avoid lifting HDD excessively, because Connector can be damaged. 1 7. ODD Remove 2 1 8. Bottom Screw Remove - Yellow( ): M2 X L4, Black (4EA) - Skyblue( ): M2.6 X L8, Black (17EA) - Red( ): M2 X L6, (2EA) 9. Push two keyboard hooks fixing a keyboard in the arrow direction * Caution When using a tool, be careful not to scratch the surface of Top and not to be hurt 3-2 3_Disassembly and Reassembly_eng2 2
10. When seperating the keyboard hook, use a tweeze, wood cutter or - screwdriver. * Caution Keyboard is connected to FPC, thus lift a little bit until FPC appear. 11. Lift up the cover of connector connected FPC of keyboard, and then pull out FPC, separate the keyboard. * Caution Avoid pulling the keyboard excessively at this time as the keyboard connector can become detached. 12. Separate 3 CABLE from TOP ASSY (TOUCH_PAD / SPEAKER / MIC Cable) 13. Separate two cables for disassembling Top. (Audio / MIC.) 3-3 3_Disassembly and Reassembly_eng3 3
- 이 문서는 삼성전자의 기술 자산으로 승인자만이 사용할 수 있습니다 Part Picture Description 14. 화 살표 방향으로 FPC Connector를 당겨서 TouchPad FPC를 분리한다. 15. And Then Remove TOP ASSY by lift up 16. W ireless LAN Card와 Bluetooth를 Board에서 분리한다. 17. R emove cables connected to Wireless LAN Card, remove screw and LAN Card. 3-4 C(MWEWWIQFP]ERH6IEWWIQFP]CIRK
18. 화살표방향으로 Bluetooth Connector 을당겨서 Bluetooth Cable 을분리하고, Screw 를풀어서 Bluetooth Module 을제거한다. M2 X L4, Black (1EA) 19. LCD Ass y 를 에서분리시키기위해서그림에표시된 2 부분의 Cable 을분리한다. 20. 화살표방향으로당겨서 Camera Cable 과 LCD Cable 을분리한다. 21. To separate LCD ASSY Remove 1,2 Screw 3-5 3_Disassembly and Reassembly_eng5 5
- 이 문서는 삼성전자의 기술 자산으로 승인자만이 사용할 수 있습니다 Part Picture Description 22. ASSY LCD and Bottom sys. 23. Remove Dummy Card in the direction of arrow. 24. Lift up board following direction. 25. BOTTOM 3-6 C(MWEWWIQFP]ERH6IEWWIQFP]CIRK
- 이 문서는 삼성전자의 기술 자산으로 승인자만이 사용할 수 있습니다 Part Picture Description 26. R emove screws for separating FAN and Heat sink. - Yellow ( ): Screw (6EA) - Red ( ): M2 X L4, Black (2EA) 27. Remove FAN CONNECTOR 28. separating FAN and Heat sink. 29. T urn the screwdriver in the direction of anticlockwise and open CPU socket. 3-7 C(MWEWWIQFP]ERH6IEWWIQFP]CIRK
30. Hold up CPU. 31. Remove rubber-lcd-cap & Screw on the LCD front. * Caution When using a tool, be careful not to scratch the surface of Top and not to be hurt. 32. 그림과같이 6 개부분의 Screw 를제거한다. M2 X L6 (6EA) 3-8 3_Disassembly and Reassembly_eng8 8
33. Separate LCD Front by twisting inside to outside like picture. * Caution When removing LCD Front, avoid twisting too strongly. If not, it can be bant. 34. Remove 4 screw in the Hinge LCD Ass'y 35. Hinge L, R 을제거한후의모습 36. LCD Panel Ass y 를분해하기위해서 INVERTER BD 를고정한 Screw 를제거한다. M2 X L5 (1EA) 3-9 3_Disassembly and Reassembly_eng9 9
37. Separate Hinge and LCD-Panel like picture 38. Screw 2 개를제거하고, Bracket 를제거한다. LCD Ass'y 39. 화살표방향으로 CAMERA MODULE 과 CABLE 을분리한다. 3-10 3_Disassembly and Reassembly_eng10 10
40. 그림과같이 Wireless LAN Antenna Cable 을제거한다. LCD Ass'y 41. LCD Panel Ass Y 와 Cable 을모두제거한후의 LCD-Back 의모습 42. LCD Panel Ass Y 의모습 3-11 3_Disassembly and Reassembly_eng11 11
43. 화살표표시 6 개의 Screw 를제거하고, Bracket -LCD _L, R 을분리한다. M2 * L5 (6 EA) 44. 화살표방향으로당겨 LCD CABLE 과 INVERTER BD 를분리한다. LCD Ass'y 1 45. 1 번, 2 번원안에있는 Tape 를제거하고, 화살표방향으로당겨 LCD Cable 을분리한다 2 46. LCD CABLE 과 INVERTER cable 을제거한 LCD Panel 의모습 3-12 3_Disassembly and Reassembly_eng12 12
LCD panel 47. Remove Speaker & Mic. LCD Ass'y 48. Taking care of removing Touchpad FPC, remove Shield of Touchpad. After that, remove Touchpad FPC. * Caution Touchpad module is fixed using by tape on Top. 3-13 3_Disassembly and Reassembly_eng13 13