PRODUCT SPECIFICTION. SCOPE( 적용범위 적용범위 ) This Product Specification covers the.5 mm(.098 inch) pitch Board to Board Connector. Series. ( 이 Spec. 은.5mm(.098 inch) pitch Board to Board Connector. 에대하여규정한다 ). PRODUCT DESCRIPTION( 제품구성 ). PRODUCT NME ND SERIES NUMBER( 제품명 & 제품번호 ) Product Name Parts Number Wafer ss y 5045 N fter TUBE Packing 500-** **50 Mated with Molex Part No. 50 N (Terminal :50 SERIES) 505 N (Terminal :559 SERIES) 55 N (Terminal :5659 SERIES). DIMENSIONS, MTERILS, PLTINGS ND MRKINGS( 치수 Refer to the attached product Drawings ( 제품도참조 ) 안전승인 ). SFETY GENCY PPROVLS( 안전승인. RTINGS( 정격 ). VOLTGE( 전압 ) 50 Volts C (RMS) {or 50 Volts DC} 허용전류 ). CURRENT( 허용전류 mps 치수, 재질, 도금 ) 사용온도범위 ) Operating : - 40 C to + 05 C Including Terminal Temperature Rise( 통전에의한온도상승분포함 ). TEMPERTURE RNGE( 사용온도 REVISION: ECR/ECN INFORMTION: DTE: 006/0/05 (5045/500) of 5
PRODUCT SPECIFICTION 4. PERFORMNCE( 성능 ) 4. ELECTRICL REQUIREMENTS( 전기적 전기적특성 ) 접촉저항 Mate connector and measured by dry circuit, 0mV and a current of 0m Connector 를결합한상태에서개방전압 0mV 이하단락전류 0m 에서측정한다. 0 milliohms [Initial] 0 mω [ 초기 ] Insulation 절연저항 Mate connector and pply a voltage of 500V DC between adjacent terminals and between terminals to ground Connector 를결합한상태에서연접하는단자와단자, 단자와접지간에 DC 500V 를가하고측정한다. 000 Mega ohms 000MΩ Dielectric Strength 내전압 Mate connector and pply a voltage of 000V C for minute between adjacent terminals and between terminals to ground. Connector 를결합한상태에서연접하는단자와단자, 단자와접지간 C 50V 를 분간가한다. No breakdown; Current leakage < 5 m 절연파괴없을것 ; 누설전류 < 5 m 기계적특성 ) 4. MECHNICL REQUIREMENTS( 기계적 Insertion and Withdrawal Force 삽입력 / 발거력 Insert and withdraw connector at the speed rate of 5 ± mm per minute. Connector 를 5 ± mm/min 의속도로삽입 / 이탈을반복하여 회,6 회,0 회째의삽입력과발거력을측정한다. Refer to Paragraph 6 제 6 항참조 Terminal/ Housing Retention Force 단자유지력 pply axial pull out force at the speed rate of 5 ± mm per minute on the terminal assembled in the housing. 터미널이결합된 Housing 을고정시키고터미널을축방향으로인발하여단자의이탈하는힘을측정한다. 9.8 N(.0kgf) 9.8 N(.0kgf) REVISION: ECR/ECN INFORMTION: DTE: 006/0/05 (5045/500) of 5
PRODUCT SPECIFICTION 4. MECHNICL REQUIREMENTS (continued) Duability 내구성 Mate connectors up to {5 cycles for tin (non-noble) plating OR 50 cycles for gold (noble) plating} at a maximum rate of 0 cycles per minute prior to Environmental Tests. 분당 0 회의주기로커넥터를인발하여내구성을측정한다 0 milliohms 0 milliohms 4 Terminal Strength When applied a load of 500gw, minute 터미널강도 500G 의하중을 분간가했을경우의강도유지상태를측정한다. 환경적특성 ) 4. ENVIRONMENTL REQUIREMENTS( 환경적 Heat 내열성 Cold 내한성 Mate connectors : Duration: 96 hours Temperature: 05 ± C 05 ± C에서 96시간방치후꺼내어외관측정한다접촉저항 Mate connectors : Duration: 96 hours Temperature: -40 ± C -40 ± C에서 96시간방치후꺼내어외관측정한다. 접촉저항 Vibration 내진동성 mplitude :.5mm P-P Sweep time : 0-55-0 Hz in minute Duration : Hours in each X,Y,Z axes 진폭 :.5mm P-P 진동수 : 0-55-0 Hz/ 분진동시간 : X,Y,Z 축각 시간 Discontinuity 외관접촉저항순간단락 microsecond μs max. REVISION: ECR/ECN INFORMTION: DTE: 006/0/05 (5045/500) of 5
PRODUCT SPECIFICTION 4. ENVIRONMENTL REQUIREMENTS (continued) 4 5 6 7 Shock 50g, strokes in each X,Y,Z axes 내충격성 50g의충격을각 X,Y,Z축에 회가한다. Humidity 내습성 Temperature Cycling 온도싸이클 Salt Spray 염수분무 내아황산성 Temperature: 40 ± C Relative humidity: 90-95% Duration: 96 hours. Remove surface moisture and air dry for hour prior to measurements. 주위온도 40 ± C, 상대습도 90-95% 상에서 96 시간방치후꺼내어측정한다. 측정 시간전에표면습기및대기건조제거한다. 5 cycles of : a) 55 ± 0minutes b) +85 ± 0minutes Discontinuity 외관접촉저항순간단락 Insulation Dielectric Strength 외관접촉저항절연저항내전압 microsecond μs max. 00Mega ohms No Breakdown at 50V C 40mΩ max. 00 MΩ min. 절연파괴없을것 5 싸이클 : 외관 a) 55 ± b) +85 ± 0분접촉저항 40mΩ max. Duration: 48±4 hours exposure; tmosphere: salt spray from the 5% solution; Temperature: 5 ± C 주위온도 : 5 ± C Solution : 5% 시간 : 48±4 시간방치 주위온도 : 40 ± C 환경 : 50ppm SO gas 시간 : 4 시간방치 외관접촉저항 외관 접촉저항 REVISION: ECR/ECN INFORMTION: DTE: 006/0/05 (5045/500) 4 of 5
PRODUCT SPECIFICTION 4. ENVIRONMENTL REQUIREMENTS (continued) 8 mmonia Gas (NH ) 내암모니아성 Duration: 40 minutes exposure; tmosphere: NH gas evaporating from a 8% mmonia solution 주위온도 : 5 ± C 외관환경 : 8% NH gas 시간 : 40분방치접촉저항 9 Solderability Solder Duration : ± 0.5 seconds Solder Temperature : 0 ± 5 C Solder coverage: 95% 납땜성 납땜시간 : ± 0.5 seconds 납땜온도 : 0 ± 5 C 95% min. 침적 0 to Soldering Heat 납땜내열성 Soldering Iron Method - Solder Duration: 5 ± 0.5 seconds; - Solder Temperature: 60 ± 5 C 수동 Solder 방식 - 납땜시간 : 5 ± 0.5 seconds; - 납땜온도 : 60 ± 5 C to insulator material 5. INSERTION/WITHDRWL FORCE( 삽입력 삽입력 / 발거력 ) [Unit : Kgf] No of Insertion Force(MX) Extraction Force(MIN) Ckt. st 6th 0th st 6th 0th.6.4.4 0.65 0.55 0.55 4.4 4. 4. 0.70 0.60 0.60 4 5. 4.8 4.8 0.75 0.65 0.65 5 6.0 5.5 5.5 0.80 0.70 0.70 6 6.6 6.0 6.0 0.90 0.80 0.80 7 7. 6.5 6.5.00 0.90 0.90 8 7.8 7.0 7.0.5.00.00 9 8.4 7.5 7.5.0.5.5 0 9.0 8.0 8.0.45.0.0 9.6 8.5 8.5.60.45.45 0. 9.0 9.0.85.60.60 0.8 9.5 9.5.00.75.75 4.4 0.0 0.0.5.90.90 5.0 0.5 0.5.0.05.05 REVISION: ECR/ECN INFORMTION: DTE: 006/0/05 (5045/500) 5 of 5