Fast changeover, fast payback: The original quick jaw change power chuck KNCS -N Easy lubrication even on vertical machines with 3 radial built-in grease nipples. Minimal set-up times Jaw change in less than 1 minute High repeatability when jaw changing No reboring of already machined jaws necessary, because runout < 0.02 mm (KNCS-N 210) Flexibility jaws can be radially adjusted and are reversible = less jaw sets Standardized mounting direct mounting Jaws radially adjustable Jaws 180 reversed Profitability Recess and bolt circle to DIN 55026 Vertical application Example set-up times/costs Jaw change Reboring of jaws Ø jaw changes/day Working days/year Machine costs/hour Total costs per year Profit* Conventional chuck 10 min 20 min 2 230 $ 60. $ 13 800. KNCS-N 1 min 0 min 2 230 $ 60. $ 460. $ 13 340. * If jaws are changed more often, the profitability is increased accordingly. 78 SMW-AUTOBLOK Version for vertical application with cover and drain holes for coolant available. Extra long, symmetrical jaw guides. Ideal for O.D. or I.D. gripping. Unique wedge bar drive for high speed. Minimum loss in gripping force because of tangentially supported wedge bars. Minimum increase of gripping force (hysteresis) after quick spindle stop. High efficiency of the wegde bar drive ensures highest concentricity and repeatability. Suitable for high-low clamping. Original SMW-AUTOBLOK patented quick jaw change. Jaw change accuracy with unique jaw safety interlock. Serration is not fully engaged jaw safety interlock active.
Clamping glossary Case hardening: The surface of the components is hardened (60 HRC) to a depth of about 1 mm (0.04 ). The core shows a high tensile strength and toughness. Compared to partial inductive hardened and nitrited parts the rigidity and the resistance against wear is greatly increased. Efficiency: The ratio between the calculated theoretical gripping force (disregarding friction) and the actual (measured) gripping force. High-low clamping: For easily deformed components. High gripping forces for the rough cut are reduced to low gripping forces for the finish cut without unchucking. This means less deformation on the finished components. Contrarily to wedge hook chucks the KNCS-N wedge bar drive is suitable for high-low clamping. Hysteresis: At high speeds the chuck body grows due to centrifugal force. The draw-pull of the clamping cylinder causes an increase in gripping force which cannot be decreased at a quick spindle stop (or change in speed). This can cause deformation at easily deformed parts. KNCS-N chucks with wedge bar drive have a very low hysteresis. Jaw change accuracy: The centering accuracy after a jaw change with once already bored/ground jaws on the chuck. The clamping force on the KNCS-N is transmitted via the wedge bar drive. The engaging/disengaging of the jaws is done by an additional tangential movement of the wedge bars. This proven and patented design with self-acting cleaning of the serration offers a constant high jaw change accuracy after jaw changing. Jaw safety interlock: At quick jaw change chucks the transmission of the gripping force to the interchangeable clamping jaws is done via a serration. With existing chuck designs misoperation by the operator can cause danger to man and machine if the jaw is not inserted correctly i.e. the serration is not fully engaged. The KNCS-N is equipped with a unique patented safety interlock: The built-in safety interlock eliminates misoperation. Repeatability: The centering accuracy of the chuck equipped with one set of jaws starting from the first up to the last component of a batch. Due to the wedge bar drive KNCS-N chucks offer a much higher repeatability compared to wedge hook chucks. Wedge bar drive: The chuck is driven by tangentially mounted wedge bars. This design allows highest repeatability and rigidity. These chucks have very low loss in gripping force due to centrifugal force. The design does not require counterbalance weights which allows highest speeds without vibration. Chuck body and internal parts are case hardened and ground. For highest rigidity, durability and precision. Large through hole for full use of spindle bore. SMW-AUTOBLOK 79 3
Main dimensions and technical data Jaw position: open position for external clamping Base jaw position»o«base jaw position»p«subject to technical changes For more detailed information please ask for customer drawing Type KNCS-N Mounting Rotating ring nut/depth Piston thread/depth Piston stroke Fixing bolt circle Fixing bolt 140-35 170-43 210-52 225-66 260-78 275-86 Z120 A5 Z140 A5 A6 Z170 A6 A8 Z170 A6 A8 Z170 Z220 A6 A8 Z220 A6 A8 Dim. A 145 175 215 225 260 275 B 87 103 98 113 115 105 122 124 105 122 124 120 120 137 139 120 144 139 C 93.9 109.9 104.9 119.9 121.9 109.9 126.9 128.9 109.9 126.9 128.9 128.3 128.3 145.3 147.3 128.3 152.3 147.3 H6 D 120 82.57 140 82.57 106.39 170 106.39 139.73 170 106.39 139.73 170 220 106.39 139.73 220 106.39 139.73 E 122 152 168 180 210 210 F 52 67 85 95 101 122 G1 * M50 x 1.5/18* M60 x 1.5/16 M75 x 1.5/16 M90 x 2/20 M95 x 2/20 G2 M45 x 1.5/18 M60 x 1.5/18 M75 x 2/19 M85 x 2/19 M102 x 2/23 M110 x 2/23 K 20 20/25 22/25 22/25 25/28 25/28 max. L 20 36 25 40 42 25 42 44 25 42 44 28 28 45 47 28 52 47 M 35 43 52 66 78 86 N 104.8 104.8 104.8 104.8 133.4 133.4 133.4 171.4 133.4 133.4 171.4 133.4 171.4 133.4 171.4 171.4 133.4 171.4 O M10 M10 M10 M10 M12 M12 M12 M16 M12 M12 M16 M12 M16 M12 M16 M16 M12 M16 P 65 75 72 82 95 105 Q 166 195 261 271 307 321 R1 M8/12 M8/12 M10/12 M10/12 M10/12 M10/18 R2 M5/10 M5/10 M6/10 M6/10 M8/16 M8/14 S 6 6 6 6 6 6 a 20 20 22 22 26 26 f7 b 8 8 10 10 12 12 c 56 65 85 85 104 104 d 28 28 33 33 36 36 H7 f 18 18 20 20 20 20 g 32 32 40 40 40 40 k M8/12 M8/12 M8/13 M8/13 M12/15 M12/15 l 6.9 6.9 4.9 4.9 8.3 8.3 m 2.5 2.5 2.5 2.5 3 3 n 5 5 4.5 4.5 5.5 5.5 max./min. o 54/39.9 69/50.2 96.6/68.3 102/69 116.6/83.6 124/85.5 max./min. p 54/39.9 60/41.2 77.6/49.3 83/50 84.6/51.6 82/53.5 Base jaw tooth pitch 4.7 4.7 4.7 4.7 5.5 5.5 Base jaw offset r 14.1 18.8 28.3 33 33 38.5 Base jaw offset teeth 3 4 6 7 6 7 95 90 60 60 60 60 60 60 60 60 60 60 Stroke per jaw at piston stroke K Stroke per jaw at piston stroke K max. max. actuating force max. total gripping force max. speed Mass without top jaws Moment of inertia mm 5.1 6.0 6.0 7.0 7.0 20 22 22 25 25 mm 5.1 6.8 7.0 7.0 8.0 8.0 20 25 25 25 28 28 kn 25 32 53 53 70 70 kn 47 60 100 100 135 135 r.p.m. 6500 6300 6000 5500 4700 4700 kg 9 9.6 14 15 15 24 26 26 26 29 29 40 40 43 43 48 53 50.7 kg. m 2 0.024 0.06 0.11 0.2 0.38 0.41 Rec. closed center cyl. Rec. open center cyl. Type Type *KNCS-N 140-35 and KNCS-N 170-43 are available with fixed ring nut only SIN-S 100 SIN-S 100/125 SIN-S 125/150 SIN-S 125/150 SIN-S 150/175 SIN-S 150/175 VNK 70-32 VNK 102-46 VNK 130-52 VNK 150-67 VNK 170-77 VNK 225-95 80 SMW-AUTOBLOK Page 282 Page 83 Page 197
Main dimensions and technical data For highest speeds: flat gripping force curve FG Total gripping force at 3 jaws (kn) 340-117 325-104 260-78 275-86 210-52 225-66 170-43 140-35 F FG Speed (r.p.m.) The data in the diagrams refer to 3-jaw-chucks, newly maintained according to their service manuals using SMW-AUTOBLOK K05 grease.the static and dynamic gripping forces have been measured using standard soft top jaws, placed in a position not exceeding the outer diameter of the chuck. FG Total gripping force at 3 jaws (kn) F FG 630-165 500-155 400-128 Speed (r.p.m.) Safety advice/danger of damage: When using taller/heavier jaws and/or clamping on a bigger diameter reduce draw pull/rotating speed accordingly. 3 Type KNCS-N Mounting H6 Rotating ring nut/depth Piston thread/depth Piston stroke max. Fixing bolt circle Fixing bolt f7 H7 max./min. max./min. Base jaw tooth pitch Base jaw offset Base jaw offset Stroke per jaw at piston stroke K Stroke per jaw at piston stroke K max. max. actuating force max. total gripping force max. speed Mass without top jaws Moment of inertia Rec. closed center cyl. Rec. open center cyl. Dim. A B C D E F G1 G2 K L M N O P Q R1 R2 S a b c d f g k l m n o p r teeth mm mm kn kn r.p.m. kg kg. m 2 Type Type 325-104 340-117 400-128 500-155 630-165 Z220 Z300 A8 A11 300 A8 A11 Z300 Z380 A11 A15 Z380 A11 A15 Z380 A15 324 340 400 500 630 130 130 149 151 130 160 151 140 140 161 163 174 195 197 174 197 139.2 139.2 158.2 160.2 139.3 169.3 160.4 149.2 149.2 170.2 172.2 184 205 207 184 207 220 300 139.73 196.88 300 139.73 196.88 300 380 196.88 285.77 380 196.88 285.77 380 285.77 268 270 330 420 585 144 160 180 207 217 M115 x 2/22 M125 x 2/22 M138 x 2/22 M165 x 2/25 M175 x 2/25 M132 x 2/25 M146 x 2/25 M160 x 2/25 M185 x 2/28 M195 x 2/28 25/28 25/28 32 42 42 28 28 47 49 28 58 49 32 32 53 55 42 63 65 42 65 104 117 128 155 165 171.4 235 171.4 235 235 171.4 235 235 330.2 235 330.2 330.2 235 330.2 330.2 330.2 M16 M20 M16 M20 M20 M16 M20 M20 M24 M20 M24 M24 M20 M24 M24 130 140 152 180 195 385 400 452 552 643 M10/16 M10/16 M12/18 M16/25 M16/25 M10/16 M10/16 M12/18 M12/18 M12/18 6 6 8 8 8 32 32 32 45 45 12 12 12 18 18 115 115 125 160 200 36 36 43 50 50 20 20 26 30 30 40 40 54 60 60 M12/17 M12/17 M12/17 M16/34 M16/34 9.3 9.3 9.3 10 10 3 3 3 4 4 6 6 7 9 9 155.7/106.2 163.2/113.7 182.3/121.8 225/141 270.5/179.5 111.7/62.2 119.2/69.7 143.3/82.2 164/80 170.5/79.5 5.5 5.5 5.5 7 7 49.5 49.5 60.5 84 91 9 9 11 12 13 60 60/35 60 60 20/9 x 40 60 60 60 60 60 7.0 7.0 25 25 8.0 8.0 8.0 10.0 10.0 28 28 32 42 42 95 95 115 120 120 180 180 240 250 250 4000 3500 3500 2200 1700 65 65 68 68 77 88.5 82.5 111 111 116 116 225 231 231 390 398 1.2 1.24 2.5 6.5 18 SIN-S 150/175/200 SIN-S 150/175/200 SIN-S175/200 SIN-S 175/200 SIN-S 175/200 VNK 250-110 VNK 320-127 VNK 320-127 VSG 450-165 VSG 450-165 SMW-AUTOBLOK 81
Ordering review Supply range: Chuck + key + mounting bolts + mounting key (from diameter 210) + 1 set hardened base jaws type GBK + 1 set soft top jaws type WAK + set of coverplates Spindle mounting Size rim small KNCS-N KNCS-N KNCS-N KNCS-N KNCS-N KNCS-N KNCS-N KNCS-N KNCS-N KNCS-N KNCS-N 140-35 170-43 210-52 225-66 260-78 275-86 325-104 340-117 400-128 500-155 630-165 Z 170 Z 220 Z 300 Z 300 088900 088912 088822 088889 Z 120 Z 140 Z 170 Z 170 Z 220 Z 220 Z 300 Z 300 Z 380 Z 380 Z 380 088800 088802 088806 088809 088901 067910 088913 067920 088823 088826 088829 rim large A 05 088801 088803 A 06 088804 088807 088810 088902 067911 A 08 088808 088811 088903 067912 088914 067921 A 11 088915 067922 088824 088827 A 15 088825 088828 088830 Supply range: Chuck + key + mounting bolts + mounting key (from diameter 210) + 1 set hardened, reversible stepped monoblock jaws type GST, ground on chuck + set of coverplates Spindle mounting Size rim small KNCS-N KNCS-N KNCS-N KNCS-N KNCS-N KNCS-N KNCS-N KNCS-N KNCS-N KNCS-N KNCS-N 140-35 170-43 210-52 225-66 260-78 275-86 325-104 340-117 400-128 500-155 630-165 Z 170 Z 220 Z 300 Z 300 088904 088916 088850 088859 Z 120 Z 140 Z 170 Z 170 Z 220 Z 220 Z 300 Z 300 Z 380 Z 380 Z 380 088831 088833 088836 088839 088905 067913 088917 067923 088851 088854 088857 rim large A 05 088832 088834 A 06 088835 088837 088840 088906 067914 A 08 088838 088841 088907 067915 088918 067924 A 11 088919 067925 088852 088855 A 15 088853 088856 088858 Supply range: Chuck + key + mounting bolts + mounting key (from diameter 210) + 1 set hardened base jaws type GBK + 1 set hardened, reversible top jaws type GUA, ground on chuck + set of coverplates Spindle mounting Size rim small KNCS-N KNCS-N KNCS-N KNCS-N KNCS-N KNCS-N KNCS-N KNCS-N KNCS-N KNCS-N KNCS-N 140-35 170-43 210-52 225-66 260-78 275-86 325-104 340-117 400-128 500-155 630-165 Z 170 Z 220 Z 300 Z 300 088908 088920 088879 088888 Z 120 Z 140 Z 170 Z 170 Z 220 Z 220 Z 300 Z 300 Z 380 Z 380 Z 380 088860 088862 088865 088868 088909 067916 088921 067926 088880 088883 088886 rim large A 05 088861 088863 A 06 088864 088866 088869 088910 067917 A 08 088867 088870 088911 067918 088922 067927 A 11 088923 067928 088881 088884 A 15 088882 088885 088887 82 SMW-AUTOBLOK
BASE JAWS and TOP JAWS GBK Hardened base jaws Chuck Jaw type KNCS-N 140 KNCS-N 170 KNCS-N 210 KNCS-N 225 KNCS-N 260 KNCS-N 275 KNCS-N 325 KNCS-N 340 KNCS-N 400 KNCS-N 500 KNCS-N 630 GBK 140 GBK 160 GBK 200 GBK 200 GBK 250 GBK 250 GBK 315 GBK 315 GBK 400 GBK 500 GBK 630 012438 012439 012440 012440 012441 012441 012442 012442 012443 012444 012445 Id. No. B 20 20 22 22 26 26 32 32 32 45 45 H 27.5 27.5 29.5 29.5 37 37 43 43 43 57 57 L 56 65 85 85 104 104 115 115 125 160 200 N 18 18 20 20 20 20 20 20 26 30 30 S 8 8 10 10 12 12 12 12 12 18 18 kg/set 0.6 0.7 1.0 1.0 1.8 1.8 2.7 2.7 3.0 7.1 9.0 WAK Soft top jaws 3 Chuck Jaw type KNCS-N 140 KNCS-N 170 KNCS-N 210 KNCS-N 225 KNCS-N 260 KNCS-N 275 KNCS-N 325 KNCS-N 340 KNCS-N 400 KNCS-N 500 KNCS-N 630 WAK 140-10 WAK 160-10 WAK 200-10 WAK 200-10 WAK 250-10 WAK 250-10 WAK 250-10 WAK 250-10 WAK 400-10 WAK 500-10 WAK 500-10 Id. No. 012490 012491 012492 012492 012493 012493 012493 012493 012494 012495 012495 B 20 20 22 22 30 30 30 30 35 45 45 H 35.5 35.5 42 42 50 50 50 50 54 75.5 75.5 L 69 85 105 105 125 125 125 125 145 180 180 A 26 42 50 50 70 70 70 70 74 100 100 kg/set 0.9 1.2 2.0 2.0 3.6 3.6 3.6 3.6 5.8 13.7 13.7 Chuck face UVB Soft monoblock jaws Chuck KNCS-N 140 KNCS-N 170 KNCS-N 210 KNCS-N 225 KNCS-N 260 KNCS-N 275 KNCS-N 325 KNCS-N 340 KNCS-N 400 KNCS-N 500 KNCS-N 630 Jaw type UVB 140 UVB 160 UVB 200 UVB 200 UVB 250 UVB 250 UVB 315 UVB 315 UVB 400 UVB 500 UVB 630 Id. No. 012446 012447 012448 012448 012449 012449 012450 012450 012451 012452 012453 B 20 20 22 22 26 26 32 32 32 45 45 H 60 60 70 70 90 90 100 100 100 134 134 h 39 39 45 45 61 61 66 66 66 87 87 L 58 69 84 84 107 107 118 118 145 175 230 kg/set 1.1 1.3 2.0 2.0 4.2 4.2 6.6 6.6 9.0 19.5 27.5 Chuck face GST Hardened stepped monoblock jaws Gripping ranges J3 J2 J1 A1 S J4 A4 A3 A2 Chuck KNCS-N 140 KNCS-N 170 KNCS-N 210 KNCS-N 225 KNCS-N 260 KNCS-N 275 KNCS-N 325 KNCS-N 340 KNCS-N 400 KNCS-N 500 KNCS-N 630 Jaw type GST 160-2 GST 170 GST 210 GST 210 GST 260 GST 260 GST 315 GST 315 GST 400 GST 500 GST 500 Id. No. 012454 035867 035863 035863 037623 037623 012457 012457 012458 012459 012459 B 20 20 22 22 26 26 32 32 32 45 45 H 43.5 43.5 51 51 60 60 66 66 70 93 93 h 23 23 26 26 31 31 32 32 36 46 46 L 58 65 84 84 100 100 117 117 137 175 175 T 7 7 8 8 10 10 10 10 11 20 20 kg/set 0.6 0.7 1.3 1.3 1.9 1.9 3.4 3.4 4.4 11.7 11.7 A1 5-40 6-59 10-85 12-96 10-98 14-113 20-115 46-141 48-173 70-225 45-240 A2 35-70 42-89 56-121 57-132 62-150 66-165 85-180 111-206 116-238 170-320 133-328 A3 66-101 73-120 96-161 97-172 111-200 115-215 140-235 166-261 184-308 315-470 283-479 A4 97-132 104-151 136-201 137-212 161-250 165-265 195-290 221-316 252-378 - - J1 39-72 44-78 60-134 62-144 63-149 67-164 80-170 106-196 118-243 - - J2 69-103 74-110 100-174 101-185 112-199 116-214 135-225 161-251 186-310 180-330 149-342 J3 99-134 105-141 140-214 141-225 161-249 165-264 190-282 216-308 253-378 325-475 297-492 J4 131-163 135-182 185-250 186-261 212-300 216-315 255-350 281-376 328-448 425-560 385-581 S 166 198 255 266 303 318 350 376 456 585 - SMW-AUTOBLOK 83
n SOFT TOP JAWS wide version n Accessories Type Id. No. B H L A kg/ SMWset AUTOBLOK WAKS 140-10 012496 35 35.5 63 25 1.5 KNCS-N 140 WAKS 160-10 080931 25 45.5 85 42 1.8 KNCS-N 170 WAKS 160-20 080932 30 50.5 75 35 2.2 WAKS 160-30 080933 35 75.5 70 26 3.4 WAKS 200-10 080934 30 51 100 57 2.9 KNCS-N 210 WAKS 200-20 080935 30 66 100 45 3.4 KNCS-N 225 WAKS 200-30 012497 40 36 70 27 1.9 WAKS 200-31 080936 40 56 90 43 3.9 WAKS 200-32 036733 40 76 95 52 5.8 WAKS 250-10 080937 40 55 125 70 3.9 KNCS-N 260 WAKS 250-11 080938 40 75 125 70 7.5 KNCS-N 275 WAKS 250-12 080939 40 95 125 70 9.6 KNCS-N 325 WAKS 250-13 080940 40 115 125 70 11.5 KNCS-N 340 WAKS 250-20 012498 60 55 90 44 6.2 WAKS 250-21 080942 60 55 110 60 7.6 WAKS 250-22 080943 60 75 90 44 9.4 WAKS 250-23 080944 60 75 110 60 11.5 WAKS 250-30 012499 80 55 90 44 8.5 WAKS 250-31 080945 80 75 110 60 14.1 WAKS 400-10 080946 40 54 110 54 4.9 KNCS-N 400 WAKS 400-11 080947 40 54 145 89 6.7 WAKS 400-12 080948 40 94 145 89 11.1 WAKS 400-13 080949 40 114 145 89 13.5 WAKS 400-14 080950 40 146 145 89 16.9 WAKS 400-20 080951 60 54 110 54 7.6 WAKS 400-21 080952 60 74 110 54 10.3 WAKS 400-22 080953 60 94 110 54 14.1 WAKS 400-30 012500 80 64 100 44 11.0 WAKS 500-10 080954 60 73 155 90 13.8 KNCS-N 500 WAKS 500-12 080956 60 113 155 90 19.5 KNCS-N 630 WAKS 500-20 080957 80 73 155 90 15.5 WAKS 500-21 080958 80 93 155 90 26.3 WAKS 500-30 012501 90 73 130 65 16.4 WAKS 500-31 012502 100 73 150 85 20.0 Accessories for KNCS-N/KNCS-NB chucks Ejector/axial stop Coolant flush E Ø25 Ø8 O M6 M6 SW13 Ø16 Ø16 Ejector stroke 25 mm 7 7 8.5 10 102 Technical data SMW-AUTOBLOK type Ejector Ejector Ejector/axial flush Coolant flush basic kit Coolant flush basic kit Coolant flush premium kit Coolant flush premium kit KNCS-N 170 KNCS-N 210 KNCS-N 225 KNCS-N 260 KNCS-N 275 KNCS-NB 210 KNCS-NB 260 E mm 68.5 61.5 61.5 46.5 46.5 min./max. O mm 69 68.3/77.8 73.7/83.1 88.6/105.1 91/113 Id. No. 174140 174142 174144 174146 175000 min./max. O mm 69 68.3/77.8 73.7/83.1 88.6/105.1 91/113 Id. No. 175001 175002 175003 175004 175005 min./max. O mm 59.6/69 68.3/96.6 73.8/120 89.1/116.6 91/124 Id. No. 176021 176022 176023 176024 176025 84 SMW-AUTOBLOK
n Hard roughing top jaws n Stop pins KNCS -N Type Id. No. B H T G N S b L kg/ SMW- Clamping range Ø Clamping range Ø Set AUTOBLOK external A 1 internal J 1 external A 2 internal J 2 GGK 1751 012464 25 40 16 M5 8 18 32 64 0.9 KNCS-N 140 28-53 125-162 - - GGK 1752 012465 68 1.0 36-56 128-168 - - GGK 1753 012466 60 1.0 55-81 101-135 - - GGK 1754 012467 56 0.9 80-105 75-109 - - GGK 1751 012464 25 40 16 M5 8 18 32 64 0.9 KNCS-N 170 25-62 133-171 33-80 155-190 GGK 1752 012465 68 1.0 32-61 134-172 42-79 153-181 GGK 1753 012466 60 1.0 52-89 107-145 70-107 125-163 GGK 1754 012467 56 0.9 77-115 81-118 95-133 99-137 GGK 2001 012469 28 45 20 M5 10 20 40 87 1.9 KNCS-N 210 29-59 187-252 36-87 - GGK 2002 012470 66 1.3 57-122 121-186 94-150 158-215 GGK 2003 012471 66 1.3 93-149 85-140 131-187 122-178 GGK 2004 012472 85 1.7 152-208 62-100 189-246 72-137 GGK 2001 012469 28 45 20 M5 10 20 40 87 1.9 KNCS-N 225 30-69 - 45-106 - GGK 2002 012470 66 1.3 67-132 131-197 105-170 169-235 GGK 2003 012471 66 1.3 104-169 95-160 141-207 134-199 GGK 2004 012472 85 1.7-68-110-74-148 GGK 2501 012473 40 50 22 M6 12 20 40 94 3.0 KNCS-N 260 45-85 197-274 61-148 254-342 GGK 2502 012474 72 2.3 78-154 132-208 141-218 195-272 GGK 2503 012475 78 2.6 107-184 109-175 159-247 152-238 GGK 2504 012476 108 3.2 - - - 80-156 GGK 2501 012473 40 50 22 M6 12 20 40 94 3.0 KNCS-N 275 49-100 201-289 65-163 258-357 GGK 2502 012474 72 2.3 82-169 136-223 145-233 199-287 GGK 2503 012475 78 2.6 111-199 113-190 163-262 156-253 GGK 2504 012476 108 3.2 - - - 84-171 GGK 2501 012473 40 50 22 M6 12 20 40 94 3.0 KNCS-N 325 34-100 210-300 - 300-370 GGK 2502 012474 72 2.3 90-175 - 170-262 - GGK 2503 012475 78 2.6-110-210 206-292 - GGK 2505 012477 84 2.8-82-150 - - GGK 2501 012473 40 50 22 M6 12 20 40 94 3.0 KNCS-N 340 60-126 236-326 - 326-396 GGK 2502 012474 72 2.3 116-201 - 196-288 - GGK 2503 012475 78 2.6-136-236 232-318 - GGK 2504 012476 84 2.8-108-186 - - GGK 4001 012478 50 55 25 M8 12 26 54 104 4.8 KNCS-N 400 78-188 258-378 143-263 333-453 GGK 4002 012479 91 3.5-140-263 258-378 - GGK 4003 012480 147 3.6-118-243 - - GGK 5001 012481 60 74 35 M8 18 30 60 125 8.8 KNCS-N 500 100-210 280-420 210-350 415-560 GGK 5002 012482 108 6.7-155-295 330-470 - GGK 5003 012483 50 74 35 M8 18 30 60 130 6.2-100-240 - - GGK 5001 012481 60 74 35 M8 18 30 60 125 8.8 KNCS-N 630 80-240 265-450 240-440 460-650 GGK 5002 012482 108 6.7-140-320 380-560 - 3 H T b G GGK Hard roughing jaw Clamping ranges Base jaw position P Base jaw position O S L N B Stop pins Type Id. No. H SW G G H SW ALB 505 016510 M5 5 10 ALB 510 016508 10 ALB 515 016509 15 ALB 605 016513 M6 5 10 ALB 610 016511 10 ALB 615 016512 15 ALB 620 017602 20 ALB 805 017603 M8 5 13 ALB 810 016514 10 ALB 815 016515 15 ALB 820 016516 20 ALB 825 081191 25 SMW-AUTOBLOK 85
Hard reversible top jaws GUA Hardened reversible top jaws Gripping ranges Base jaw position o "0" "0" "P" Base jaw position p "P" J2 J1 A1 S J6 A6 A5 J5 J4 A4 A2 A3 J3 Chuck KNCS-N 140 KNCS-N 170 KNCS-N 210 KNCS-N 225 KNCS-N 260 KNCS-N 275 KNCS-N 325 KNCS-N 340 KNCS-N 400 KNCS-N 500 KNCS-N 630 Jaw type GUA 160 GUA 160 GUA 200 GUA 200 GUA 250 GUA 250 GUA 250 GUA 250 GUA 400 GUA 500 GUA 630 Id. No. 012484 012484 012485 012485 012486 012486 012486 012486 012487 012488 012488 B 20 20 22 22 30 30 30 30 36 45 45 H 32.5 32.5 38 38 50 50 50 50 56 70 70 L 63 63 72 72 90 90 90 90 105 130 130 T 7.5 7.5 10 10 14 14 14 14 15 20 20 kg/set 0.6 0.6 0.8 0.8 1.9 1.9 1.9 1.9 3.2 10.8 10.8 A1 17-42 32-69 55-111 65-131 73-150 77-165 120-205 146-231 138-258 190-336 192-385 A2 63-89 60-98 69-125 79-145 45-90 49-105 48-120 74-146 78-188 80-200 85-220 A3 88-115 85-123 96-152 106-172 125-170 129-185 130-200 156-226 186-298 200-320 205-340 A4 17-42 13-51 17-73 27-93 20-86 24-161 36-188 62-214 60-183 55-200 60-192 A5 63-89 78-116 104-163 117-183 76-154 80-169 120-205 146-231 143-268 190-335 225-425 A6 88-115 103-141 131-190 144-210 156-234 160-249 205-285 231-311 253-378 315-455 345-545 J1 77-101 91-129 117-174 128-194 152-229 156-244 202-285 228-311 218-338 305-450 345-540 J2 101-126 116-154 144-201 155-221 233-310 237-325 280-365 306-391 328-448 425-570 465-660 J3 146-172 144-181 158-215 169-235 204-249 208-264 208-280 234-306 263-380 335-450 355-490 J4 77-101 74-111 80-136 90-156 101-166 105-181 110-200 136-226 138-263 170-310 200-345 J5 101-126 99-136 107-163 117-183 180-246 184-261 198-280 224-306 248-373 290-430 320-465 J6 146-172 162-200 193-253 207-273 235-312 239-327 276-365 302-391 333-458 425-570 495-695 S 166 198 196-253/255 207-273/276 322 337 390 416-590 700 For further jaws and accessories please ask for our 150 pages special catalogue! 86 SMW-AUTOBLOK
Grease Grease Gun Important for maintenance and safe operation, to be ordered with the chuck Grease K05 Special grease for manual and power chucks Cartridge 14 Oz. (DIN 1284) Grease content 500 g Id. No. 016440 Grease gun Grease gun (DIN 1283) for cartridges 14 Oz. (DIN 1284). n Also refillable from grease can 1000 g. 3 Can 1000 g Id. No. 011881 n High adhesion n High resistance against coolant n High load bearing capacity n Low friction coefficient n High gripping force n Avoids tribocorrosion Lubrication set Id. No. 083726 Supply range n Grease gun n 1 Adapter flexible for high pressure grease nipple n 1 Adapter for cone grease nipple SMW-AUTOBLOK 87