Rev: 001 Product Family Data Sheet LM561B - 5630 Middle Power LED Introduction Features Beam Angle: 120 Precondition : JEDEC Level 2a Dimension : 5.6 x 3.0 x 0.8 mm ESD withstand Voltage : up to ± 5KV [HBM] Applications INDOOR LIGHTING : Ambient Light, LED tube, Down light, LED bulb and Ceiling Light SAMSUNG ELECTRONICS 95, Samsung2-Ro, Giheung-Gu, Yongin-City, Gyeonggi-Do 446-711, KOREA Copyright 1995-2013 SAMSUNG ELECTRONICS Co.,Ltd. All rights reserved. The information in this document is subject to change without notice. SAMSUNG, is a registered trademark of SAMSUNG ELECTRONICS. http://www.samsungled.com 1 / 46
Contents 1. Product Code Information ----------------------- 3 2. Characteristics ----------------------- 9 3. Typical Characteristics Graph ----------------------- 10 4. Outline Drawing & Dimension ----------------------- 16 5. Reliability Test Items & Conditions ----------------------- 17 6. Solder Conditions ----------------------- 18 7. Tape & Reel ----------------------- 19 8. Label Structure ----------------------- 20 9. Packing Structure ----------------------- 21 10. Precaution For Use ----------------------- 23 11. Hazard Substance Analysis Report ----------------------- 26 Revision History ----------------------- 46 http://www.samsungled.com 2 / 46
1. Product Code Information 1) Luminous Flux Bins (T s = 25 ) Nominal CCT Product Code Flux Rank Sorting Condition lm @65mA Flux Range (Φ v, lm) SPMWHT541MD5WAW0S1 S1 24.0 ~ 26.0 2700K SPMWHT541MD5WAW0S2 S2 26.0 ~ 28.0 SPMWHT541MD5WAW0S3 S3 28.0 ~ 30.0 SPMWHT541MD5WAV0S1 S1 24.5 ~ 26.5 3000K SPMWHT541MD5WAV0S2 S2 26.5 ~ 28.5 SPMWHT541MD5WAV0S3 S3 28.5 ~ 30.5 SPMWHT541MD5WAU0S1 S1 25.0 ~ 27.0 3500K SPMWHT541MD5WAU0S2 S2 27.0 ~ 29.0 SPMWHT541MD5WAU0S3 S3 29.0 ~ 31.0 SPMWHT541MD5WAT0S1 S1 26.0 ~ 28.0 4000K SPMWHT541MD5WAT0S2 S2 28.0 ~30.0 SPMWHT541MD5WAT0S3 S3 30.0 ~32.0 SPMWHT541MD5WAR0S1 S1 27.0 ~ 29.0 5000K SPMWHT541MD5WAR0S2 S2 29.0 ~ 31.0 SPMWHT541MD5WAR0S3 S3 31.0 ~ 33.0 SPMWHT541MD5WAQ0S1 S1 26.5 ~ 28.5 5700K SPMWHT541MD5WAQ0S2 S2 28.5 ~ 30.5 SPMWHT541MD5WAQ0S3 S3 30.5 ~ 32.5 SPMWHT541MD5WAP0S1 S1 26.0 ~ 28.0 6500K SPMWHT541MD5WAP0S2 S2 28.0 ~ 30.0 SPMWHT541MD5WAP0S3 S3 30.0 ~ 32.0 Notes: SAMSUNG ELECTRONICS maintains a tolerance of ±5% on Luminous Flux measurements http://www.samsungled.com 3 / 46
2) Color Bins (T s = 25 ) 1) Color Binning Nominal CCT Product Code Color Rank Chromaticity Bins 2700K SPMWHT541MD5WAW0S1 SPMWHT541MD5WAW0S2 SPMWHT541MD5WAW0S3 W0(Whole bin) W1, W2, W3, W4, W5, W6, W7, W8, W9, WA, WB, WC, WD, WE, WF, WG 3000K SPMWHT541MD5WAV0S1 SPMWHT541MD5WAV0S2 SPMWHT541MD5WAV0S3 V0(Whole bin) V1, V2, V3, V4, V5, V6, V7, V8, V9, VA, VB, VC, VD, VE, VF, VG 3500K SPMWHT541MD5WAU0S1 SPMWHT541MD5WAU0S2 SPMWHT541MD5WAU0S3 U0(Whole bin) U1, U2, U3, U4, U5, U6, U7, U8, U9, UA, UB, UC, UD, UE, UF, UG 4000K SPMWHT541MD5WAT0S1 SPMWHT541MD5WAT0S2 SPMWHT541MD5WAT0S3 T0(Whole bin) T1, T2, T3, T4, T5, T6, T7, T8, T9, TA, TB, TC, TD, TE, TF, TG 5000K SPMWHT541MD5WAR0S1 SPMWHT541MD5WAR0S2 SPMWHT541MD5WAR0S3 R0(Whole bin) R1, R2, R3, R4, R5 R6, R7, R8, R9,RA 5700K SPMWHT541MD5WAQ0S1 SPMWHT541MD5WAQ0S2 SPMWHT541MD5WAQ0S3 Q0(Whole bin) Q1, Q2, Q3, Q4, Q5 Q6, Q7, Q8, Q9, QA 6500K SPMWHT541MD5WAP0S1 SPMWHT541MD5WAP0S2 SPMWHT541MD5WAP0S3 P0(Whole bin) P1, P2, P3, P4, P5 P6, P7, P8, P9, PA http://www.samsungled.com 4 / 46
2) Chromaticity Region & Coordinates http://www.samsungled.com 5 / 46
2) Chromaticity Region & Coordinates (Continued) Region CIE X CIE Y Region CIE X CIE Y W rank (2700K) Region CIE X CIE Y Region CIE X CIE Y V rank (3000K) 0.4373 0.3893 0.4465 0.4071 0.4147 0.3814 0.4221 0.3984 W1 0.4418 0.3981 0.4513 0.4164 W9 0.4475 0.3994 0.4573 0.4178 V1 0.4183 0.3898 0.4259 0.4073 V9 0.4242 0.3919 0.4322 0.4096 0.4428 0.3906 0.4523 0.4085 0.4203 0.3833 0.4281 0.4006 0.4428 0.3906 0.4523 0.4085 0.4203 0.3833 0.4281 0.4006 W2 0.4475 0.3994 0.4573 0.4178 WA 0.4532 0.4008 0.4634 0.4193 V2 0.4242 0.3919 0.4322 0.4096 VA 0.4300 0.3939 0.4385 0.4119 0.4483 0.3919 0.4582 0.4099 0.4259 0.3853 0.4342 0.4028 0.4483 0.3919 0.4582 0.4099 0.4259 0.3853 0.4342 0.4028 W3 0.4532 0.4008 0.4634 0.4193 WB 0.4589 0.4021 0.4695 0.4207 V3 0.4300 0.3939 0.4385 0.4119 VB 0.4359 0.3960 0.4449 0.4141 0.4538 0.3931 0.4641 0.4112 0.4316 0.3873 0.4403 0.4049 0.4538 0.3931 0.4641 0.4112 0.4316 0.3873 0.4403 0.4049 W4 0.4589 0.4021 0.4695 0.4207 WC 0.4646 0.4034 0.4756 0.4221 V4 0.4359 0.3960 0.4449 0.4141 VC 0.4418 0.3981 0.4513 0.4164 0.4593 0.3944 0.4700 0.4126 0.4373 0.3893 0.4465 0.4071 0.4418 0.3981 0.4513 0.4164 0.4183 0.3898 0.4259 0.4073 W5 0.4465 0.4071 0.4562 0.4260 WD 0.4523 0.4085 0.4624 0.4274 V5 0.4221 0.3984 0.4299 0.4165 VD 0.4281 0.4006 0.4364 0.4188 0.4475 0.3994 0.4573 0.4178 0.4242 0.3919 0.4322 0.4096 0.4475 0.3994 0.4573 0.4178 0.4242 0.3919 0.4322 0.4096 W6 0.4523 0.4085 0.4624 0.4274 WE 0.4582 0.4099 0.4687 0.4289 V6 0.4281 0.4006 0.4364 0.4188 VE 0.4342 0.4028 0.4430 0.4212 0.4532 0.4008 0.4634 0.4193 0.4300 0.3939 0.4385 0.4119 0.4532 0.4008 0.4634 0.4193 0.4300 0.3939 0.4385 0.4119 W7 0.4582 0.4099 0.4687 0.4289 WF 0.4641 0.4112 0.4750 0.4304 V7 0.4342 0.4028 0.4430 0.4212 VF 0.4403 0.4049 0.4496 0.4236 0.4589 0.4021 0.4695 0.4207 0.4359 0.3960 0.4449 0.4141 0.4589 0.4021 0.4695 0.4207 0.4359 0.3960 0.4449 0.4141 W8 0.4641 0.4112 0.4750 0.4304 WG 0.4700 0.4126 0.4813 0.4319 V8 0.4403 0.4049 0.4496 0.4236 VG 0.4465 0.4071 0.4562 0.4260 0.4646 0.4034 0.4756 0.4221 0.4418 0.3981 0.4513 0.4164 http://www.samsungled.com 6 / 46
2) Chromaticity Region & Coordinates (Continued) Region CIE X CIE Y Region CIE X CIE Y U rank (3500K) Region CIE X CIE Y Region CIE X CIE Y T rank (4000K) 0.3889 0.3690 0.3941 0.3848 0.367 0.3578 0.3702 0.3722 U1 0.3915 0.3768 0.3968 0.3930 U9 0.3981 0.3800 0.4040 0.3966 T1 0.3726 0.3612 0.3763 0.376 T9 0.3744 0.3685 0.3782 0.3837 0.3953 0.3720 0.4010 0.3882 0.3686 0.3649 0.3719 0.3797 0.3953 0.3720 0.4010 0.3882 0.3726 0.3612 0.3763 0.3760 U2 0.3981 0.3800 0.4040 0.3966 UA 0.4048 0.3832 0.4113 0.4001 T2 0.3783 0.3646 0.3825 0.3798 TA 0.3804 0.3721 0.3847 0.3877 0.4017 0.3751 0.4080 0.3916 0.3744 0.3685 0.3782 0.3837 0.4017 0.3751 0.4080 0.3916 0.3783 0.3646 0.3825 0.3798 U3 0.4048 0.3832 0.4113 0.4001 UB 0.4116 0.3865 0.4186 0.4037 T3 0.3840 0.3681 0.3887 0.3836 TB 0.3863 0.3758 0.3912 0.3917 0.4082 0.3782 0.4150 0.3950 0.3804 0.3721 0.3847 0.3877 0.4082 0.3782 0.4150 0.3950 0.384 0.3681 0.3887 0.3837 U4 0.4116 0.3865 0.4186 0.4037 UC 0.4183 0.3898 0.4259 0.4073 T4 0.3898 0.3716 0.395 0.3875 TC 0.3924 0.3794 0.3978 0.3958 0.4147 0.3814 0.4221 0.3984 0.3863 0.3758 0.3912 0.3917 0.3915 0.3768 0.3968 0.3930 0.3686 0.3649 0.3719 0.3797 U5 0.3941 0.3848 0.3996 0.4015 UD 0.4010 0.3882 0.4071 0.4052 T5 0.3744 0.3685 0.3782 0.3837 TD 0.3763 0.376 0.3802 0.3916 0.3981 0.3800 0.4040 0.3966 0.3702 0.3722 0.3736 0.3874 0.3981 0.3800 0.4040 0.3966 0.3744 0.3685 0.3782 0.3837 U6 0.4010 0.3882 0.4071 0.4052 UE 0.4080 0.3916 0.4146 0.4089 T6 0.3804 0.3721 0.3847 0.3877 TE 0.3825 0.3798 0.3869 0.3958 0.4048 0.3832 0.4113 0.4001 0.3763 0.376 0.3802 0.3916 0.4048 0.3832 0.4113 0.4001 0.3804 0.3721 0.3847 0.3877 U7 0.4080 0.3916 0.4146 0.4089 UF 0.4150 0.3950 0.4222 0.4127 T7 0.3863 0.3758 0.3912 0.3917 TF 0.3887 0.3836 0.3937 0.4001 0.4116 0.3865 0.4186 0.4037 0.3825 0.3798 0.3869 0.3958 0.4116 0.3865 0.4186 0.4037 0.3863 0.3758 0.3912 0.3917 U8 0.4150 0.3950 0.4222 0.4127 UG 0.4221 0.3984 0.4299 0.4165 T8 0.3924 0.3794 0.3978 0.3958 TG 0.395 0.3875 0.4006 0.4044 0.4183 0.3898 0.4259 0.4073 0.3887 0.3836 0.3937 0.4001 http://www.samsungled.com 7 / 46
2) Chromaticity Region & Coordinates (Continued) Region CIE X CIE Y Region CIE X CIE Y R rank (5000K) 0.3366 0.3369 0.3456 0.3601 R1 R2 R3 R4 R5 Q1 Q2 Q3 Q4 Q5 0.3441 0.3428 0.3539 0.3669 R6 0.3449 0.3515 0.3551 0.3760 0.3369 0.3451 0.3464 0.3688 0.3441 0.3428 0.3363 0.3287 0.3515 0.3487 0.3433 0.3341 R7 0.3527 0.3578 0.3441 0.3428 0.3449 0.3515 0.3366 0.3369 0.3369 0.3451 0.3433 0.3341 0.3449 0.3515 0.3503 0.3396 R8 0.3456 0.3601 0.3515 0.3487 0.3373 0.3534 0.3441 0.3428 0.3449 0.3515 0.3376 0.3616 0.3527 0.3578 0.3464 0.3688 R9 0.3539 0.3669 0.3471 0.3775 0.3456 0.3601 0.3379 0.3698 0.3373 0.3534 0.3464 0.3688 0.3456 0.3601 0.3551 0.3760 RA 0.3464 0.3688 0.3564 0.3851 0.3376 0.3616 0.3471 0.3775 Q rank (5700K) 0.3222 0.3243 0.3292 0.3461 0.3294 0.3306 0.3373 0.3534 Q6 0.3293 0.3384 0.3376 0.3616 0.3217 0.3316 0.3292 0.3539 0.3294 0.3306 0.3227 0.3170 0.3366 0.3369 0.3295 0.3228 Q7 0.3369 0.3451 0.3294 0.3306 0.3293 0.3384 0.3222 0.3243 0.3217 0.3316 0.3295 0.3228 0.3293 0.3384 0.3363 0.3287 Q8 0.3292 0.3461 0.3366 0.3369 0.3212 0.3389 0.3294 0.3306 0.3293 0.3384 0.3207 0.3462 0.3369 0.3451 0.3292 0.3539 Q9 0.3373 0.3534 0.3291 0.3617 0.3292 0.3461 0.3202 0.3535 0.3212 0.3389 0.3292 0.3539 0.3292 0.3461 0.3376 0.3616 QA 0.3292 0.3539 0.3379 0.3698 0.3207 0.3462 0.3291 0.3617 Region CIE X CIE Y Region CIE X CIE Y P rank (6500K) 0.3068 0.3113 0.3126 0.3324 P1 P2 P3 P4 P5 0.3145 0.3187 0.3210 0.3408 P6 0.3135 0.3256 0.3205 0.3481 0.3055 0.3177 0.3117 0.3393 0.3145 0.3187 0.3081 0.3049 0.3221 0.3261 0.3154 0.3119 P7 0.3216 0.3334 0.3145 0.3187 0.3135 0.3256 0.3068 0.3113 0.3055 0.3177 0.3154 0.3119 0.3135 0.3256 0.3226 0.3188 P8 0.3126 0.3324 0.3221 0.3261 0.3041 0.3240 0.3145 0.3187 0.3135 0.3256 0.3028 0.3304 0.3216 0.3334 0.3117 0.3393 P9 0.3210 0.3408 0.3107 0.3461 0.3126 0.3324 0.3015 0.3368 0.3041 0.3240 0.3117 0.3393 0.3126 0.3324 0.3205 0.3481 PA 0.3117 0.3393 0.3200 0.3554 0.3028 0.3304 0.3107 0.3461 Notes: SAMSUNG ELECTRONICS maintains ±0.007 tolerance of Cx, Cy http://www.samsungled.com 8 / 46
2. Characteristics 1) Absolute Maximum Rating Item Symbol Rating Condition Operating temperature range Top -40 ~ +85 - Storage temperature range Tstg -40 ~ +120 - LED junction temperature T J 110 - Forward Current I F 150 ma - Peak Pulsed Forward Current IFP 300 ma Duty 1/10 pulse width 10ms Thermal resistance Rth, j-s 16 /W Junction to solder point Assembly Process Temperature - 260, < 10sec - ESD - 5kV HBM 2) Electro-optical Characteristics Item Forward Voltage 1) (V F) (@65 ma, Ts = 25 ) Luminous Flux 2) (Φ v) (@65 ma, Ts = 25 ) Unit Nominal CCT Product Code V - - WA lm 2700K (W0) 3000K (V0) 3500K (U0) 4000K (T0) 5000K (R0) 5700K (Q0) 6500K (P0) Rank Min Typ Max AZ 2.70-2.80 A1 2.80-2.90 A2 2.90-3.00 A3 3.00-3.10 A4 3.10-3.20 *WAW0S1 S1 24.0-26.0 *WAW0S2 S2 26.0-28.0 *WAW0S3 S3 28.0-30.0 *WAV0S1 S1 24.5-26.5 *WAV0S2 S2 26.5-28.5 *WAV0S3 S3 28.5-30.5 *WAU0S1 S1 25.0-27.0 *WAU0S2 S2 27.0-29.0 *WAU0S3 S3 29.0-31.0 *WAT0S1 S1 26.0-28.0 *WAT0S2 S2 28.0-30.0 *WAT0S3 S3 30.0-32.0 *WAR0S1 S1 27.0-29.0 *WAR0S2 S2 29.0-31.0 *WAR0S3 S3 31.0-33.0 *WAQ0S1 S1 26.5-28.5 *WAQ0S2 S2 28.5-30.5 *WAQ0S3 S3 30.5-32.5 *WAP0S1 S1 26.0-28.0 *WAP0S2 S2 28.0-30.0 *WAP0S3 S3 30.0-32.0 Reverse Voltage V - - - 0.7-1.2 (@5 ma, Ts = 25 ) Color Rendering Index 3) (R a) - - - 5 80 - - Special CRI 4) (R9) - - - - 0 - - Notes: 1)~4) SAMSUNG ELECTRONICS maintains a tolerance of V F:±0.1 V, Φ v:±5 %, R a :±3.0, R9 :±6.5 on measurements 5) " * " is Product Code of "SPMWHT541MD5" http://www.samsungled.com 9 / 46
3. Typical Characteristics Graph (T s = 25 ) 1) Spectrum Distribution [CCT : 2700K & 3000K] [CCT : 3500K & 4000K] http://www.samsungled.com 10 / 46
[CCT : 5000K & 5700K] [CCT : 6500K] http://www.samsungled.com 11 / 46
2) Forward Current Characteristics [Relative Luminous Flux vs. Forward Current] (T s = 25 ) [Forward Current vs. Forward Voltage] (T s = 25 ) http://www.samsungled.com 12 / 46
3) Temperature Characteristics [Relative Luminous Flux vs. Ts] (I F = 65mA) [Forward Voltage vs. Ts] (I F = 65mA) http://www.samsungled.com 13 / 46
4) Color shift Characteristics [Forward Current vs. Color x, y] (T s = 25 ) http://www.samsungled.com 14 / 46
5) Derating Curve 6) Beam Angle Characteristics http://www.samsungled.com 15 / 46
4. Outline Drawing & Dimension 1. Tolerance is ±0.10 mm 2. The maximum compressing force is 15N on the body a 3. Do not place pressure on the encapsulation resin b Left Side View Top View Bottom View Anode Mark a b Cathode Anode Front View Recommended Land Pattern Notes: 1) This LED has built-in ESD protection device(s) connected in parallel to LED Chip(s). 2) Ts point & measurement method 1 Measure the nearest point to the thermal pad. If necessary, remove PSR of PCB to reach Ts point. 2 Thermal pad must be soldered to the PCB to dissipate heat properly. Otherwise, LED can be damaged. 3) Precautions 1 The pressure on the LEDs will influence to the reliability of the LEDs. Precautions should be taken to avoid the strong pressure on the LEDs. Do not put stress on the LEDs during heating. 2 Re-soldering should not be done after the LEDs have been soldered. If re-soldering is unavoidable, LED`s characteristics should be carefully checked before and after such repair. 3 Do not stack assembled PCBs together. Since materials of LEDs is soft, abrasion between two PCB assembled with LED might cause catastrophic failure of the LEDs. http://www.samsungled.com 16 / 46
5. Reliability Test Items and Conditions 1) Test Items Test Item MSL Test Room Temperature life test High Temperature life test High Temperature humidity life test Low Temperature life test Powered Temperature Cycle test Thermal Shock High Temperature Storage Low Temperature Storage ESD(HBM) ESD(MM) Test Conditions 125 24hrs drying 60, 60%RH 120hrs 260 10sec 3 cycles Test Hours/Cycles Sample No 1 cycle 11 25 ±3, DC150 ma 1,000hrs 22 85 ±3, DC150 ma 1,000hrs 22 85 ±3, 85%±2%RH, DC150 ma 1,000hrs 22-40 ±3, DC150 ma 1,000hrs 22-45 /20 min 85 /20 min, Sweep 100min cycle on/off: each 5 min, DC 150mA 100 cycle 22-45 /15 min 125 /15 min Hot plate 180 500 cycle 100 Ta=120 ±3 1000 hrs 11 Ta=-40 ±3 1000 hrs 11 R1:10 MΩ, R2:1.5 kω, C:100 pf, V = ±5 kv R1:10 MΩ, R2: 0, C:200 pf, V = ±0.5 kv 5times 5 5times 5 Vibration Test 20~2000~20 Hz 200 m/s 2, Sweep 4 min X, Y, Z 3 direction, each 1 cycle 4 cycles 11 Mechanical Shock Test 1500G, 0.5 ms, 3 shocks each X-Y-Z axis 5 cycles 11 2) Criteria for Judging the Damage Item Symbol Test Condition Min Limit Max Forward Voltage V F I F = 65 ma Init. Value*0.9 Init. Value*1.1 Luminous Flux Φ v I F = 65 ma Init. Value*0.7 Init. Value*1.2 http://www.samsungled.com 17 / 46
6. Solder Conditions 1) Reflow Conditions ( Pb Free ) Reflow Frequency : 2 times max. 2) For Manual Soldering Not more than 5 seconds @Max. 300, under soldering iron. http://www.samsungled.com 18 / 46
7. Tape & Reel unit:mm PKG direction in carrier tape pocket Anode Mark (Cutting ) End Start More than 500 mm Unloaded tape Mounted with Flash LED More than 100~200 mm Unloaded tape Leading part more than 500 mm (1) Quantity : The quantity/reel to be Max. 2,000 pcs,. (2) Cumulative Tolerance : Cumulative tolerance/10 pitches to be ±0.2 mm (3) Adhesion Strength of Cover Tape : Adhesion strength to be 0.1-0.7N when the cover tape is turned off from the carrier tape at 10 angle to be the carrier tape. (4) Packaging : P/N, Manufacturing data code no. and quantity to be indicated on a damp proof Package. http://www.samsungled.com 19 / 46
8. Label Structure 1) Label Structure abcdef AZ 1S1 SPMWHT541MD5WA 0S1 AZ 1S1 01 IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII GLAW94001 / 1001 / 2,000pcs IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII Rank Code N.B) Denoted rank is the only example. ' ' means All kind of Chromaticity Coordinate Rank. Rank Code ab : Forward Voltage(V F ) Rank (refer to page. 9) cd : Chromaticity Coordinate Rank (refer to page. 5~8) ef : Luminous Flux(Φ v, lm) Rank (refer to page. 3) 2) LOT Number The Lot number is composed of the following characters AZ 1S1 SPMWHT541MD5WA 0S1 AZ 1S1 01 IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII GLAW94001 / 1001 / 2,000pcs IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII 123456789 / 1abc / 2,000PCS 1 2 : L (LED) 3 4 : Year (V:2011, W:2012, X:2013...) 5 : Month (1 ~ 9, A, B) 6 : Day (1 ~ 9, A, B ~ V) 789 : SAMSUNG ELECTRONICS LED Product number (1 ~ 999) abc : Reel Number (1 ~ 999) : Production Site (S:SAMSUNG ELECTRONICS, G:GOSIN CHINA) : Product State (A:Normality, B:Bulk, C:First Production, R:Reproduction, S:Sample) http://www.samsungled.com 20 / 46
9. Packing Structure 1) Packing Process Reel AZ 1S1 SPMWHT541MD5WA 0S1 AZ 1S1 01 IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII GLAW94001 / 1001 / 2,000pcs IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII LEVEL 2a Aluminum Vinyl Bag AZ 1S1 SPMWHT541MD5WA 0S1 AZ 1S1 01 IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII GLAW94001 / 1001 / 2,000pcs IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII Material : Paper(SW3B(B)) TYPE SIZE(mm) L W H 7inch 245 220 182 1 SIDE AZ 1S1 SPMWHT541MD5WA 0S1 AZ 1S1 01 IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII GLAW94001 / 1001 / 2,000pcs IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII H CHIP LED L W 1 http://www.samsungled.com 21 / 46
2) Aluminum Packing Bag AZ 1S1 SPMWHT541MD5WA 0S1 AZ 1S1 01 IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII GLAW94001 / 1001 / 2,000pcs IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII Silica gel & Humidity Indicator Card in Aluminum Vinyl Bag http://www.samsungled.com 22 / 46
10. Precaution for use 1) For over-current-proof function, customers are recommended to apply resistors to prevent sudden change of the current caused by slight shift of the voltage. 과전류방지를위해전압의미세한이동에의해야기되는전류의순간변화를방지하기위해저항등의설치를권장함. 2) This device should not be used in any type of fluid such as water, oil, organic solvent, etc. When washing is required, IPA is recommended to use. 제품은물, 오일, 유기물과같은액체타입에서의사용은제한되며, 세정이필요할시에는 IPA 사용을권장함. 3) When the LEDs illuminate, operating current should be decided after considering the ambient maximum temperature. LED 의발광시, 동작전류는주변최고온도를고려하여결정되어야함. 4) LEDs must be stored in a clean environment. If the LEDs are to be stored for 3 months or more after being shipped from Samsung Electronics, they should be packed by a sealed container with nitrogen gas injected.(shelf life of sealed bags: 12 months, temp. ~40, ~90%RH) LED 의보관은청정한환경에서보존되어져야하며, 만약삼성전자로부터공급받는후 3 개월또는그이상보관이필요하다면질소가스를동봉한보존용기에보관되어야함. ( 보존 bag 의수명 : 12 개월, 보존온도 ~40, 습도 ~90%RH) 5) After storage bag is open, device subjected to soldering, solder reflow, or other high temperature processes must be: 보존 Bag 이개봉된후에, 납땜이나 reflow 등의높은온도에노출되는제품은다음의사항에부합되어야함. a. Mounted within 672 hours(28 days) at an assembly line with a condition of no more than 30 /60%RH, a. 제품은 30 /60%RH 보다같거나낮은조립조건에서 672 시간 (28 일 ) 이내에조립해야함. b. Stored at <10%RH. b. 10% 이하의상대습도에서보관되어야함. 6) Repack unused Products with anti-moisture packing, fold to close any opening and then store in a dry place. 사용하지않은제품은방습팩에넣어개봉부위를닫아서다시포장한후, 건조한장소에서보관할것을권장함. http://www.samsungled.com 23 / 46
7) Devices require baking before mounting, if humidity card reading is >60% at 23±5. 만약습도표시카드의수치가 23±5 에서 60% 이상이라면, 제품실장전 baking 해야함. 8) Devices must be baked for 1 hour at 65±5, if baking is required. 만약 baking 이필요하다면, 제품은 65±5 에서 1 시간정도 baking 되어야함. 9) The LEDs are sensitive to the static electricity and surge. It is recommended to use a wrist band or anti-electrostatic glove when handling the LEDs. LED 는정전기및서지에민감한제품이므로, LED 제품을다룰시에는정전기방지장갑이나손목밴드를사용하기를권장함. If voltage exceeding the absolute maximum rating is applied to LEDs, it may cause damage or even destruction to LED devices. 만약절대허용치를초과하는전압이 LED 에가해지면, LED 소자는파괴되거나손상될수있음. Damaged LEDs may show some unusual characteristics such as increase in leak current, lowered turn-on voltage, or abnormal lighting of LEDs at low current. 손상된제품은누설전류의증가, Turn on 전압의저하, 저전류에서의점등불량등의이상거동을보일수있음. 10) VOCs (volatile organic compounds) may be occurred by adhesives, flux, hardener or organic additives which is used in luminaires (fixture) and LED silicone bags are permeable to it. It may lead a discoloration when LED expose to heat or light. VOCs( 휘발성유기화합물 ) 는등기구에사용되는접착제, Flux, 경화제, 유기물첨가제에서발생하여 LED 실리콘봉지제를투과하고, 빛또는열에노출되었을때변색이발생할수있음. This phenomenon can give a significant loss of light emitted(output) from the luminaires(fixtures). 이러한현상은등기구로부터나오는빛의중대한손실을줄수있음. In order to prevent these problems, we recommend you to know the physical properties for the materials used in luminaires, It requires to select carefully. 이러한문제발생방지를위해서, 등기구에사용되는자재에대한물성을알고주의하여선택되어야함. http://www.samsungled.com 24 / 46
11) Risk of Sulfurization (or Tarnishing) The lead frame from Samsung Electronics is a plated package and it may change to black(or dark colored) when it is exposed to Ag (a), Sulfur (S), Cchlorine (Cl) or other halogen compound. It requires attention. 삼성전자의리드프레임은 Ag( 은 ) 을도금한 Package 제품으로황 (S), 염소 (Cl), 또는다른할로겐화합물들에노출시 Ag( 은 ) 은검정 ( 또는어두운색 ) 으로바뀔수있으니주의가필요함. Sulfide (Sulfurization) of the lead frame may cause a change of degradation intensity, chromaticity coordinates and it may cause open circuit in extreme cases. It requires attention. 리드프레임의황화 (Sulfurization) 는광량저하, 색좌표변화및심한경우회로내의 LED 무등 (Open) 불량을일으킬수도있으니주의가필요함. Sulfide (Sulfurization) of the lead frame may cause of storage and using with oxidizing substances together. Therefore, LED is not recommend to use and store with the below list. : Rubber, Plain paper, lead solder cream etc. 리드프레임황화 (Sulfurization) 의근원이될수있으니 LED 는아래의목록으로만들어진산화성물질들과함께저장, 사용이불가함 : 고무, 일반종이, 남땜크림등 http://www.samsungled.com 25 / 46
11. Hazard Substance Analysis - SGS http://www.samsungled.com 26 / 46
http://www.samsungled.com 27 / 46
http://www.samsungled.com 28 / 46
http://www.samsungled.com 29 / 46
http://www.samsungled.com 30 / 46
http://www.samsungled.com 31 / 46
11. Hazard Substance Analysis - SVHC(REACH) http://www.samsungled.com 32 / 46
http://www.samsungled.com 33 / 46
http://www.samsungled.com 34 / 46
http://www.samsungled.com 35 / 46
http://www.samsungled.com 36 / 46
http://www.samsungled.com 37 / 46
http://www.samsungled.com 38 / 46
http://www.samsungled.com 39 / 46
http://www.samsungled.com 40 / 46
http://www.samsungled.com 41 / 46
http://www.samsungled.com 42 / 46
http://www.samsungled.com 43 / 46
http://www.samsungled.com 44 / 46
http://www.samsungled.com 45 / 46
Revision History Writer Date No. Revision History Drawn Approved 2013.2.08 001 New version W.H Jung Y.T KIM http://www.samsungled.com 46 / 46