THERMAL RE-WRITABLE CARD READER /WRITER TCP400II SERIES User s Manual 操作手册이용안내
Trademark acknowledgments TCP400II: Star Micronics Co., Ltd. Notice All rights reserved. Reproduction of any part of this manual in any form whatsoever, without STAR s express permission is forbidden. The contents of this manual are subject to change without notice. All efforts have been made to ensure the accuracy of the contents of this manual at the time of going to press. However, should any errors be detected, STAR would greatly appreciate being informed of them. The above notwithstanding, STAR can assume no responsibility for any errors in this manual. Copyright 2005-2014 Star Micronics Co., Ltd.
TABLE OF CONTENTS 1. Precautions for Safe Use...4 2. Unpacking...6 3. External Appearance and Part Names...6 4. Connecting to External Devices...7 5. Connecting the Power Cord...8 6. Setting Fonts Using the Font Setting Card...9 7. Cleaning Cards...9 8. Troubleshooting... 11 ENGLISH Appendixes A. Connection Settings... 31 B. Removing / Installing Interface Board... 33 C. Optional Ethernet Interface IFBD-HE05/07... 34 D. General Specifications... 35 This User s Manual describes important information to enable you to use the reader/writer safely. Carefully read this manual before using the reader/writer and observe the descriptions herein. WEEE Statement In the European Union, this label indicates that this product should not be disposed of with household waste. It should be deposited at an appropriate facility to enable recovery and recycling in accordance with legislation under the WEEE Directive (Directive 2002/96/EC).
1. Precautions for Safe Use Always observe the following items. Carefully read and obey the following items to prevent injury to yourself or to others and to prevent damaging property. 1-1. Precautions for Reader/Writer Setup 1. Setup the reader/writer in a solid, and level location. 2. Do not use or place the reader/writer in areas exposed to direct sunlight, or near heat sources. 3. Avoid using or storing the reader/writer in areas of high humidity. Do not use or store liquids near the reader/writer. 4. Avoid using or storing the reader/writer in locations where there is dust or other airborne particles. 5. Avoid using the reader/writer in locations where corrosive gases, ignition gases, chemicals or vapors are emitted. 6. Do not operate the reader/writer near devices which may produce magnetic fields or interference. 7. Do not get power from a circuit to which electrical devices that generate electrical noise are connected. 8. Connect a grounding wire to use this device safely. 9. Allow plenty of space around the reader/writer for ventilation. 1-2. Precautions for Reader/Writer Use 1. Use only Star recommended cards. 2. Do not use cards that are dirty or oily or wet in any other manner. Also, do not handle cards with dirty or wet hands. Do not apply tape or glue to cards. 3. Do not place cards near devices that generate magnetic fields (such as cellular telephones, speakers, televisions, etc.). 4. Do not place cards in direct sunlight or high temperature areas (such as dashboards in automobiles), as high temperatures can cause cards to bend or can erase the information recorded on cards. 5. Do not use bent cards, as this can cause them to become jammed in the reader/writer. 6. Insert cards in the indicated direction. 7. Never insert anything other than the appropriate cards into the reader/writer. 8. Do not obstruct the insertion or discharge path of the cards. 9. Do not cut the power while a card is being processed. 10. In case of reader/writer error (abnormal sounds, abnormal odors, smoke, fire) turn off the reader/writer immediately and unplug it from the power outlet. 4
11. Always hold the plug to unplug the power cord from its outlet. Pulling on the cord will damage the cord. 12. When disconnecting use for prolonged periods, always remove the power plug from the outlet. 13. Do not use the reader/writer in an environment where condensation has formed. 14. To ensure reader/writer reliability, clean the reader/writer everyday, or when the cleaning lamp has lit. 15. Avoid contact with the optional cleaning liquid. If it gets in your eyes, or is ingested, seek immediate medical assistance. 16. Do not disassemble or modify the reader/writer. 17. Do not expose cards to direct sunlight or fluorescent lights for extended periods of time. 18. If a card is to be reprinted, allow for at least three minutes between prints. When printing repeatedly to different cards, no wait is required. 19. This symbol is placed near the thermal print head and erase head to indicate that it may be hot. Never touch the thermal print head and erase head immediately after the printer has been used. Let the thermal print head and erase head cool for a few minutes before touching it. 20. This symbol is placed near the thermal print head and erase head to indicate that it is easily damaged. Observe the precautions for handling electrostatic sensitive devices. 21. Be careful not to drop paper clips, pins or other foreign matter into the unit as these cause the reader/writer to malfunction. 22. Do not open the cover while operating. 23. The reader/writer is equipped with a DC motor or switches which use electrical contacts. Plese avoid using the reader/writer in an area where silicon gas is present. 5
2. Unpacking The following outlines the reader/writer and its accessories. 1. Reader/writer 2. Power cord 1 7 3. Cleaning cards (2 cards) 4. Ferrite core 5. This manual 6. Font setting card 7. RS-232C Interface card Note: Whether there are a ferrite core and font setting card depends on the reader/writer model. 6 3 5 2 4 3. External Appearance and Part Names 2 3 4 5 7 1 6 1. Power Switch...This turns the power to the reader/writer on and off. 2. Power Lamp...Indicates that reader/writer power is on. 3. Status Lamp...Indicates printer ready, printing and errors. 4. Cleaning Lamp...Indicates the reader/writer needs cleaning. 5. Interface Connector...Connects to host computer via a cable. 6. AC Inlet...Connects to accessory power cord. 7. Cleaning Switch...Press the cleaning switch while turning the power on. Insert a cleaning card dampened with alcohol to clean the reader/writer. 6
4. Connecting to External Devices Connect either the RS-232C interface Cable or USB interface Cable to the reader/writer. To use the RS-232C interface cable, exchange the USB interface board for the RS-232C interface board that comes with the reader/writer. See the Appendix B (page 33). 4-1 Mounting the RS-232C Interface Cable 1. Cut the power to the host computer and the reader/writer. 2. Connect one end of the interface cable to the reader/writer and the other end to the host computer. 3. Mount the accessory ferrite core to the interface cable. 4. Tighten the left and right screws on the connector. 4-2 Mounting the USB Interface Cable 1. Affix the ferrite core onto the USB cable as shown in the illustration below and make sure to pass the cable through the cable support as shown in the illustration. 2. Plug on end of the USB cable into the USB port on the back of the reader/writer. 3. Plug the other end of the USB cable into the USB port of the host computer. 4. If a driver for the reader/writer is required, use the media that was distributed by your agent to install the driver. 7
5. Connecting the Power Cord 1. Turn the power switch off. 2. Connect the powr cord to the AC inlet on the backside of the reader/writer. 3. Insert the power cord plug into a properly grounded AC outlet. Connect the grounding terminal to a metal portion (such as an outlet that has a grounding point) on a ground in the vicinity to use this reader/writer safely. Caution: We recommend that you unplug the reader/writer from the power outlet whenever you do not plan to use it for long period. Because of this, you should locate the reader/writer so that the power outlet it is plugged into is nearby and easy to access. 8
6. Setting Fonts Using the Font Setting Card European, US and Korean bound models are provided a standard font setting card that is for their country. Before using the reader/writer, set the fonts according to the directions below. <Procedures to Set Fonts> 1. Turn the power ON while pressing the Cleaning switch. 2. The buzzer will ring and the green status lamp will flash. This indicates that the reader/ writer has entered the setting mode to use the setting card. 3. Insert the font setting card. The font setting information is automatically read from the magnetic strip. That new font setting information is then written to the internal memory. 4. When the new settings have been completed successfully, COMPLETE! is printed and the card is discharged. The reader/writer will then return to its normal operating status. Status Lamp Font Setting Card Cleaning Switch 7. Cleaning Cards A cleaning card is used to clean the transport rollers inside the unit. Two cleaning cards accompany each unit. They are in the plastic wrap. 7-1 External Shape 22.0 54.0 Felt Surface 85.6 89.6 Felt Surface 9
7-2 Frequency of Use 1. Everyday, or once every 300 prints. 2. If errors occur repeatedly, or if there are printing problems, clean the reader/writer. 3. The cleaning LED will flash when there have been 300 printings. Clean the reader/ writer when this flashes. 7-3 How to Use Use the following procedures to clean the reader/writer. 1. Press the cleaning switch. 2. Dampen the felt surfaces (both side) of a cleaning card with optional cleaning liquid. 3. Insert the cleaning card from the normal card insertion inlet. 4. Allow the reader/writer to sit for approximately one minute before using again, to allow it to dry. Note: 1. Do not use bent cleaning cards. Using bent cards can cause them to become jammed. 2. A cleaning fluid is not supplied with the unit. Therefore, an optional cleaning fluid or a commercially available ethanol (85% minimum purity) must be obtained. To obtain the optional cleaning fluid, contact your sales agent. 3. The attached cleaning card attains its cleaning effectiveness by absorbing a cleaning fluid before use. Make sure to allow it to absorb a cleaning fluid before using it for cleaning. 4. Make sure to use ethanol with a minimum purity of 85%. If ethanol with a lower purity is used, it will take the cleaning card a longer time to dry. If an undried cleaning card is inserted into the slot, it could cause a malfunction, such as card slippage. 5. Cleaning cards can be used approximately 30 times. Contact your sales agent if they are damaged or excessively dirty. Cleaning Switch 10
8. Troubleshooting 8-1. Trouble when Turning on the Power The power lamp does not light. The power lamp lights. Symptom Possible Cause What to Do Won t accept cards. Accepts cards. Won t accept cards. Accepts cards but reader/ writer operating incorrectly. The power cord is not correctly connected. Broken wire in power cord. Broken wire in fuse. Display LED burned out. Reader/writer error. Bad Card Card damaged, bent, data erased on card, or other user card. Head is dirty. Composing system is not operating normally. Reader/writer error. Correct connect the power cord. Contact your dealer. Use a normal card. Clean using a cleaning card. Contact your dealer. 8-2. Trouble when Operating Symptom Possible Cause What to Do Cards are not discharged. Card is jammed. Turn on power to reader/ writer again. If cards are still not discharged, turn off the power and open the upper cover. Then, pull the snap lever to raise the upper portion of the mechanism to remove the card. Reading/Writing errors occur Inappropriate card. Use the recommended card. Using other card type. Use the correct card. Card data erased by magnet. Issue a new card. Card is bent. Card is damaged. Head is dirty. Clean using a cleaning card. 11
8-3. Removing Jammed Cards 1. Turn off the power and unplug the reader/writer. 2. Press the cover opener. 3. Lift the upper cover while the cover is open. Upper cover Cover Opener 4. While pulling the mechanism s snap lever, lift the mechanism. Note: Do not touch the thermal head or erasing head. There is the danger of getting burned. Thermal head Erase head Snap lever 5. Remove the card while the cover is open. Caution: Trying to remove the card by forcibly pulling it will damage internal parts such as the card guides. Remove the card by pushing it along the card guides and out of the card inlet. 6. Return the mechanism to its original position. 7. Close the upper cover. 12
目录 1. 使用时注意事项... 14 2. 开箱检查... 16 3. 外型结构... 16 4. 连接外置设备... 17 5. 连接电源线... 18 6. 使用字库设置卡设置字库... 19 7. 清洗卡... 19 8. 故障处理... 21 附录.... 31 中文 附录.只出现在本手册的英语部分中 此手册说明如何安全地使用读写机 使用读写机之前, 请仔细阅读此手册
1. 使用时注意事项 经常注意以下各项 仔细阅读以下各项, 避免造成伤害 1-1. 安装时注意事项 1. 放置读写机于平稳的工作台 2. 避免读写机受阳光接照射或靠近热源 3. 避免读写机在太过潮湿的环境下使用 避免读写机靠近液体 4. 避免读写机周围布满灰尘 5. 避免读写机靠近腐蚀性气体 易燃性气体 化学物体等 6. 避免读写机靠近能产生磁场或干扰的设备 7. 避免读写机与其它能产生电力的设备插于同一插座 8. 读写机需要连接地线 9. 读写机的周围应有足够空气流通 1-2. 使用时注意事项 1. 请使用 Star 公司提供的重写卡 2. 当重写卡已经弄脏 布满油或弄湿, 请不要再使用 另外, 不要在重写卡表面上贴上胶带或涂上胶水 3. 避免重写卡靠近能产生磁场的设备 如 : 手机 播放器 电视等设备 4. 避免重写卡受阳光直接照射或靠近高温 因为高温会对卡造成变形或删除存储在卡内的信息 5. 不要使用已经变形的重写卡, 因为会造成卡卡现象 6. 按印在卡上的指示方向插入重写卡 7. 请勿插入不符合规格的重写卡 8. 避免放置物件于卡的进出口位置 9. 机器运作时, 不要切断电源 10. 当读写机发生错误时, 如发出不正常声音 异味 冒烟等, 请马上关闭读写机电源并拔掉电源线 11. 拔掉电源线时, 手要拿住电源线的插头来拔掉 12. 如准备长时间不会使用读写机, 请拔掉电源线 14
13. 避免读写机靠近积水的地方 14. 为保持读写机的可靠性, 最好每天清洗打印头或当清洗灯亮着时才进行清洗 15. 避免眼睛接触选购的清洗剂 如不小心接触了清洗剂, 请马上看医生 16. 不要自行拆装读写机 17. 避免重写卡长时间受阳光或灯光直接照射 18. 如同一张卡需要重写, 请至少等待三分钟才重写 但如重写是另一张卡, 则无需等待 19. 此标记贴于打印头和擦写头旁 刚使用完打印机后, 请勿触摸打印头或擦写头 请等待打印头和擦写头冷却后, 才可触摸 20. 此标记贴于打印头和擦写头旁 请勿直接触摸打印头和擦写头, 防止对静电较敏感的设备的造成破坏 21. 小心不要将纸夹 销或其它杂质掉落到本机中, 否则会造成读 / 写头故障 22. 操作时请勿打开盖 23. 读 / 写头配有直流电机或使用电触点的开关 请不要在有硅燃气的地方使用读 / 写头 15
2. 开箱检查 打开包装箱, 对照下图检查箱内部件是否齐全 1. 读写机 2. 电源线 3. 清洗卡 ( 两张 ) 4. 磁芯 5. 操作手册 6. 字库设置卡 7. RS-232C 接口卡 注 : 是否有磁芯和字体设置卡取决于读 / 写头型号 3. 外型结构 1 6 3 5 7 2 4 2 3 4 5 7 1 6 1. 电源开关... 启动或关闭读写机电源 2. 电源灯... 表示读写机的电源状态 3. 状态灯... 表示读写机的各种状态 4. 清洗灯... 表示打印头是否需要清洗 5. 接口... 通过连接线连接主机 6. 电源线插座... 连接电源线 7. 清洗键... 按住清洗键开机, 然后插入已涂上清洗剂的清洗卡 16
4. 连接外置设备 使用 RS-232C 串口线或 USB 线连接读写机 如需使用 RS-232C 串口线, 请将 USB 接口板更换为读写机随附的 RS-232C 接口板 请参见附录. B( 第 33 页 ) 4-1 使用 RS-232C 串口线连接 1. 关闭主机和读写机的电源 2. 插入串口线的一端至读写机, 而串口线的另一端插入主机 3. 安装随机的磁芯在串口线 4. 锁紧插头 4-2 使用 USB 串口线连接 1. 如下图所示, 将磁芯固定在 USB 线上, 并确定如图所示将线穿过线支架 2. 将 USB 线的一端插入读写机的 USB 端口 3. 将 USB 线的另一端插入主机的 USB 端口 4. 安装驱动 17
5. 连接电源线 1. 关闭读写机开关 2. 在机后插上电源线 3. 将电源线的另一端插入电源插座 警告 : 如准备长时间不会使用读写机, 请拔掉电源线 因此建议读写机靠近电源插座, 方便拔插 18
6. 使用字库设置卡设置字库 如是欧洲 美国 韩国版本机型, 随机会有一张标准的字库设置卡 请根据以下步骤进行设置 : < 设置字库步骤 > 1. 按住清洗键开机 2. 蜂鸣器会响一声, 状态灯会以绿色闪烁 这表示读写机已进入设置模式 3. 插入字库设置卡, 读写机会阅读卡上磁带的数据, 然后写入机内, 存储设置值 4. 当设置完成后, COMPLETE! 样字会打印在卡上并会退卡, 然后读写机会自动回复至正常模式 状态灯 字库设置卡 7. 清洗卡 清洗键 清洗卡是用于清洗在机内接触卡面的滚轮 随机带有两张卡, 已放在小透明袋子内 7-1 外型 85.6 89.6 22.0 54.0 毛毡面 毛毡面 19
7-2 使用频率 1. 每日或每打印 300 次 2. 如果错误不停出现或打印出现问题, 尝试清洗读写机 3. 打印 300 次后, 清洗灯会闪烁 此时需要清洗读写机 7-3 如何使用 根据以下步骤清洗读写机 : 1. 按下清洗键 2. 在清洗卡的毛毡面 ( 两面 ) 涂上选购的清洗剂 3. 插入清洗卡 4. 如需要连续使用, 请等待约一分钟, 让清洗剂在卡面干透 注意 : 1. 不要使用已变形的清洗卡 使用已变形的清洗卡会造成卡卡 2. 本机不附带清洗剂 因此, 必须有选购的清洗剂或市售酒精 ( 纯度 85% 以上 ) 若要得到选购的清洗剂, 请联系销售代理商 3. 使用前, 安装的清洁卡会吸收清洗剂以达到清洁效果 请务必让其吸收清洗剂再进行清洁 4. 务必使用纯度为 85% 以上的酒精 如果酒精纯度低, 则需要更长的时间将清洁卡烘干 如果插入在槽中的卡片未烘干, 会导致故障, 如卡片滑落 5. 清洗卡可用约 30 次 清洗键 20
8. 故障处理 8-1. 开机故障 电源灯不亮 电源灯不亮 8-2. 操作上故障 故障现象 原因 处理 卡不能进读写机 可能电源线未插好 把电源线插好 可能电源线内的线断开 可能保险丝烧掉 联络经销商 卡能进读写机 可能面版灯烧掉 卡不能进读写机 可能读写机故障 使用另一张卡再 试 卡能进读写机, 但读写操作不正常 可能坏卡 卡变形 存在卡内的数据丢失或插错卡 可能打印头已弄脏 可能系统操作不正常 可能读写机故障 使用清洗卡清洗读写机 联络经销商 故障现象 原因 处理 不能退卡 可能卡卡 关闭读写机电源, 然后再启动 如卡仍然不能退出, 关闭读写机电源, 打 开上盖 拉开绿色铜杆并往上提起机芯的 上部份, 手动推出重写卡 读写故障 可能使用不正确的重写卡 使用建议的重写卡 可能使用另一类型的重写卡 使用正确的重写卡 可能卡上的数据已 被磁铁删除 可能卡变形 重新的发行新的重写卡 可能卡已经损坏 可能打印头已弄脏 使用清洗卡清洗读写机 21
8-3. 清除卡卡 1. 关闭读写机电源, 拔掉电源线 2. 按下上盖开关 3. 打开上盖 4. 拉动铜杆, 并同时向上提起机芯 注意 : 避免接触热敏打印头和清除打印头 热敏打印头 清除打印头 5. 手动推出重写卡 铜杆 注意 : 尝试用力拉拽插卡将其取出会损坏内部零件如插卡导杆 请沿着插卡导杆将插卡推出插卡口来取出插卡 6. 退回机芯的上部份到原来位置 7. 关上上盖开关 22
목록표 1. 안전한사용을위한사전주의사항... 24 2. 포장풀기... 25 3. 외양및부품명칭... 26 4. 외부기기와의연결... 26 5. 전원케이블연결... 27 6. 폰트설정카드를사용하여폰트설정하기... 27 7. 크리닝카드... 28 8. 장애시해결... 29 부록... 31 부록미번역. KOREAN 본사용자매뉴얼은본기기의안전한사용을위한중요한정보를기술하고있습니다. 기기를사용하기전이매뉴얼을주의깊게읽어보시고사용방법을준수하여주시기바랍니다. 23
1. 안전한사용을위한사전주의사항 언제나이하의항목을지켜주세요. 다음을주의깊게읽으시고안내사항을잘준수하여귀하와타인에대한부상이나장비의손실을방지하시기바랍니다. 1-1. 리더 / 라이터설치시주의사항 1. 평평하고단단한곳에서본리더 / 라이터를설치하십시오. 2. 직사광선이나열에직접노출된곳에서는본기기를사용하거나교체하지마십시오. 3. 습기가높은곳에서본기기를저장하거나운용하지마십시오. 본기기근접한곳에서액체물질을사용하거나저장하지마십시오. 4. 먼지나대기에분진이있는장소에서본기기를사용하거나저장하지마십시오. 5. 부식또는발화성이있는가스, 화학물질혹은기포가분출되는장소에서본기기를운용하지마십시오. 6. 자기장또는간섭을생성하는기기가근접한곳에서본기기를운용하지마십시오. 7. 전자장애가발생되는전자기기의회로에전원을연결하지마십시오. 8. 본기기의안전한운용을위해접지를하십시오. 9. 환기를위해기기주변에충분한공간을확보해주십시오. 1-2. 리더 / 라이터사용시주의사항 1. 당사가추천한카드만을사용하십시오. 2. 더럽거나기름묻었거나젖은카드및카드를기타다른용도로사용하지마십시오. 또한더럽거나젖은손으로카드를다루지마십시오. 카드에테이프나접착제를사용하지마십시오. 3. 자기 ( 磁氣 ) 가발생하는기기 ( 핸드폰, 스피커, TV 등의 ) 주변에카드를놓지마십시오. 4. 직사광선이나고온이발생하는곳 ( 자동차의대쉬보드등 ) 에카드를놓지마십시오. 카드가휘어지거나저장된정보가손실될우려가있습니다. 5. 카드를구부리지마십시오. 기기내에서걸림현상을일으킬수있습니다. 6. 지시된방향으로카드를삽입하십시오. 7. 적절한카드외에어떠한물질도기기안으로삽입하지마십시오. 8. 카드의삽입 / 배출시손대지마십시오. 9. 카드데이터가기록 / 소거되는중전원을끄지마십시오. 10. 기기에러일경우 ( 비정상소음, 진동, 연기, 발화 ), 즉시기기의전원을끄고전원플러그를콘센트에서뽑으십시오. 11. 콘센트에서전원코드를뽑아두십시오. 코드를잡아당기면코드가상할수있습니다. 12. 기기를오랫동안사용치않을경우전원코드를콘센트에서뽑아두십시오. 13. 수분응축현상이발생하는곳에서는기기를사용하지마십시오. 14. 기기의신뢰성을유지하기위해매일또는크리닝램프가깜빡일경우기기를청소해주십시오. 15. 액세서리인크리닝액사용시주의하십시오. 만일눈에들어가거나마셨을경우즉시응급처치를받으십시오. 24
16. 기기를분해하거나수정하지마십시오. 17. 카드를직사광선또는형광등에오랜기간노출시키지마십시오. 18. 이표시는감열헤드및소거헤드가까이에표시되어있으며헤드가뜨거울수있음을나타냅니다. 프린터사용직후에는절대감열헤드및소거헤드를만지지마십시오. 몇분뒤감열헤드가식은후만지도록하십시오. 19. 이표시는감열헤드및소거헤드가까이에표시되어있으며헤드가쉽게손상될수있음을나타냅니다. 정전기에민감한기기를다룰때의주의사항을준수하십시오. 프린터가사용된후, 열인자헤드와소거헤드에결코닿지말아주세요. 손대기전에몇분간열인자헤드와소거헤드를냉각시켜주세요. 20. 본표시는프린터감열헤드및소거헤드주위에표시되어있으며쉽게손상될수있음을의미합니다. 21. 페이퍼클립, 핀또는기타이물질을리더 / 라이터위에떨어뜨리지마십시오.. 고장의원인이될수있습니다. 22. 운용중에커버를열지마십시오. 23. 리더 / 라이터는전기가흐르는 DC 모터또는스위치가장착되어있습니다. 규소가스가있는곳에서리더 / 라이터를사용하지마십시오. 2. 포장풀기 다음은기기및액세서리내역입니다. 1. 본체 2. 전원코드 3. 크리닝카드 ( 2 장 ) 4. 페릿코어 5. 매뉴얼 6. 폰트설정카드 7. RS-232C 인터페이스보드 참고 : 페릿코어및폰트설정카드의포함여부는리더 / 라이터모델에따라다릅니다. 1 6 3 5 7 2 4 25
3. 외양및각부위명칭 2 3 4 1. 전원스위치... 기기를켜거나끕니다. 2. 전원램프... 기기에전원이켜진것을나타냅니다. 3. 상태램프... 프린터의준비상태, 출력및에러를나타냅니다. 4. 크리닝램프... 기기청소시점을나타냅니다. 5. 인터페이스연결부... 케이블을통해호스트컴퓨터에연결합니다. 6. AC 전원부... 전원코드에연결합니다. 7. 크리닝스위치... 전원을켜고크리닝스위치를누릅니다. 알코올을묻힌크리닝카드를삽입하여기기를청소합니다. 4. 외부기기에연결 7 1 RS-232C 인터페이스케이블또는 USB 인터페이스케이블을기기에연결합니다. RS-232C 인터페이스케이블을사용하여 USB 인터페이스보드를리더 / 라이터에포함된 RS-232C 인터페이스보드로교환하십시오. 부록 B(33 페이지 ) 를참조하십시오. 4-1. RS-232C 인터페이스케이블연결하기. 1. 호스트컴퓨터및기기의전원을끕니다. 2. 기기와호스트컴퓨터를인터페이스케이블로연결합니다. 3. 액세서리인페릿코어를인터페이스케이블에감아줍니다. 4. 연결부의좌 / 우나사를고정시킵니다. 4-2. USB 인터페이스케이블연결하기 1. 기기와호스트컴퓨터를인터페이스케이블로연결합니다. 2. 그림과같이 USB 케이블을케이블고정후크에걸어줍니다. 3. 기기용드라이버가필요한경우대리점에서제공되는미디어를사용드라이버를설치하십시오. 4. 기기용드라이버가필요하면대리점에서제공된미디어를활용, 드라이버를설치하십시오. 5 6 26
5. 전원코드연결하기 1. 전원스위치를끕니다. 2. 기기의후면에있는 AC 전원부에전원코드를연결합니다. 3. 전원코드를적절히고정된 AC 콘센트에꼽아줍니다. 본기기의안전한사용을위해접지부분을지면의금속부위 ( 접지되어있는콘센트 ) 에연결하십시오. 주의 : 기기를오랜기간사용하지않을경우, 전원코드를뽑아주십시오. 장래에사용할경우에대비해서콘센트가가까운곳에기기를두시는것이좋습니다. 6. 폰트설정카드를사용하여폰트설정하기 유럽, 미국및한국용모델에는표준형폰트카드가제공됩니다. 기기를사용하기전, 하단안내사항에따라폰트를설정하십시오. < 폰트설정절차 > 1. 크리닝스위치를누른상태에서전원을켜십시오. 2. 부저가울리면서녹색상태램프가깜빡거리는데, 이는기기가 설정카드사용을위한설정모드 로바뀐것을나타냅니다. 3. 폰트설정카드를삽입하십시오. 자기띠의폰트설정정보가자동으로읽혀집니다. 이때새로운폰트설정정보가내부메모리에저장됩니다. 4. 새로운설정이성공적으로수행되면, COMPLETE 가인자되고카드가배출됩니다. 이때기기는일반사용모드로되돌아갑니다. 상태확인램프 폰트세팅카드 크리닝스위치 27
7. 크리닝카드 크리닝카드는기기내부의이송롤러를청소하는데사용됩니다. 두장의카드가동봉되어있으며플라스틱랩으로쌓여있습니다. 7-1. 외양 22.0 54.0 7-2. 크리닝횟수 1. 매일또는 300 매출력후 2. 에러가반복되거나또는출력시문제가생기면기기를청소하여주십시오. 3. 300 매출력후, 크리닝 LED 가깜빡거립니다. 이때기기를청소하여주십시오. 7-3. 사용법 85.6 89.6 다음절차에따라기기를청소하여주십시오. 1. 크리닝스위치를누릅니다. 2. 크리닝카드의펠트표면 ( 양면 ) 에헤드크리닝액을묻힙니다. 3. 일반카드삽입구에크리닝카드를삽입합니다. 4. 약일분뒤, 기기가건조되면다시사용하여주십시오. 참고 : 1. 휘어진크리닝카드를사용하지마십시오. 걸림현상의원인이됩니다. 2. 크리닝액은내역에포함되어있지않습니다. 옵션으로크리닝액을구입하거나시중에서판매하는에탄올 ( 최소순도 85%) 을구입하십시오. 옵션으로크리닝액을구입하려면대리점에문의하십시오. 3. 크리닝카드는사용전에크리닝액을흡수해야그기능을발휘합니다. 크리닝카드를사용하기전에반드시크리닝액을도포해주십시오. 4. 순도가최소 85% 인에탄올을사용하십시오. 이보다낮은순도의에탄올을사용하면크리닝카드가건조하는데더많은시간이소요되며, 건조되지않은크리닝카드를슬롯에삽입하면카드미끄럼과같은고장을일으킬수있습니다. 5. 크리닝카드는약 30 회사용할수있습니다. 만일카드가손상되거나매우더러울경우, 구매처에연락하십시오. 크리닝스위치 28
8. 장애해결 8-1. 전원을켤때장애 증상원인조치사항 전원램프가안켜짐. 전원램프가켜짐. 카드가삽입되지않음. 전원코드가바르게연결되지않음. 전원코드손상. 휴즈손상. 카드가삽입됨. 표시 LED 손상. 카드가삽입되지리더 / 라이터에러. 않음. 불량카드카드손상, 휘어짐, 데이터손상된카드사용. 카드가삽입되나기기가올바르게헤드오염. 동작하지않음. 전원코드를바르게연결. 구매처에연락. 정상카드사용. 크리닝카드를이용, 청소. 시스템이정상적으로동작하지않음. 구매처에연락. 리더 / 라이터에러. 8-2. 동작중장애 증상원인조치사항 카드가배출되지않음. 카드막힘현상. 기기를다시켭니다. 여전히카드가배출되지않으면전원을끄고상단커버를엽니다. 스냅레버를당겨서메커니즘상단부를들어올린후카드를제거합니다. 부적절한카드. 권장카드사용. 다른카드사용. 올바른카드사용. 리더 / 라이터에러발생. 자기에의한데이터삭제. 새로운카드사용. 휘어진카드. 카드손상. 헤드오염. 크리닝카드를사용청소. 29
8-3. 카드막힘제거 1. 파워를끄고기기의전원코드를뽑습니다. 2. 커버오프너를누릅니다. 3. 커버가열려진상태에서윗부분을들어올립니다. 상단커버 커버오프너 4. 메커니즘의스냅레버를당겨서메커니즘을들어올립니다. 참고 : 감열헤드또는소거헤드에손대지마십시오. 화상을입을수있습니다. 감열헤드 소거헤드 스냅레버 5. 커버가열린상태에서카드를제거합니다. 주의 : 카드를강제로빼면카드가이드와같은내부부품이손상될수있습니다. 카드가이드에맞춰카드를눌러빼주십시오. 6. 메커니즘을원래위치에두십시오. 7. 상단커버를닫습니다. 30
Appendix A: Connection Settings A-1. RS-232C Interface < RS-232C Serial Interface Specifications > 1. Connectors D-Sub 9PIN (Male) * Reader/Writer Side 2. Compatible Connectors D-Sub 9PIN (Female) * Cable Side 3. Connector Pins See Table Below 4. I/O Circuit See Table Below 5. Level RS-232C 6. Cable Cross (Reverse) Cable Pin No. Signal Name I/O Functions 1 NC - Not Connected 2 RXD Input Reception Data 3 XD Output Transmission Data 4 DTR Output Data Terminal Ready 5 GND - Ground for Signal 6 DSR Input Data Set Ready (Not Detected) 7 RTS Output Transmission Request 8 CTS Input Transmission Ready (Not Detected) 9 NC - Not Connected < Settings for Communication Speed > To change the serial communication settings, change the following DIP switch settings. (Ex-factory Default Settings: DSW 1 to 6 are ON, 7 and 8 are OFF.) Switches ON OFF DSW 1-1 Baud Rate Setting (See table below) DSW 1-2 DSW 1-3 Fixed at On DSW 1-4 Parity Disabled Parity Enabled DSW 1-5 Odd Parity Even Parity DSW 1-6 Fixed at On DSW 1-7 Fixed at Off DSW 1-8 Fixed at Off Baud Rates BPS 4800 BPS 9600 BPS 19200 BPS 38400 BPS DSW 1-1 OFF ON ON OFF DSW 1-2 ON ON OFF OFF * If incorrect switch settings are made, there may be a failure of the card reader/writer. Be careful when making setting changes. APPENDIX 31
To change the DIP switch settings, do the following. 1. Check that the power is turned off for both the reader/writer and the host computer. 2. Remove the two screws. 3. Pull out the interface card to remove it. 4. Change the DIP switch settings on the interface card. 5. Push in the interface card to mount it. 6. Tighten the two screws. 7. Turn on the power for both the reader/writer and the host computer. Note: The new settings will take effect when the reader/writer power is turned back on. DIP switch A-2. USB Interface Specifications 1 Communication Rating Conforms to USB 2.0 Specifications 2 Communication Speed USB Full Speed Mode (Max. 12 MBPS) 3 Communication Method USB Bulk Transmission Mode 4 Power Specifications USB Self-power Function 5 Connectors Type-B 32
Appendix B: Removing / Installing Interface Board B-1. Removing 1. Turn off the power switch. Then, unplug the power cord from the outlet. 2. Remove the two screws as shown in the figure below. 3. Pull the interface board in the direction of the arrow to remove it. B-2. Installing 1. Insert the interface board to the reader/writer. Note: Firmly insert so that the reader/writer connector and the interface board connector are securely connected. 2. Tighten the two screws to fasten the interface board. 3. After connecting the interface board, run a test print using the following steps before connecting the interface cable. If the connection is good, the model of the connected I/F will be printed. < How to Run a Test Print > Turn on the power while pressing the CLEANING switch. The buzzer will ring and the green status lamp will flash. Press the CLEANING switch again. The status lamp will switch to orange and will flash. Insert a card in this state. This will cause the system to automatically write data to the magnetic stripe and to read data therefrom. The test results will be printed, and the card will be discharged. The results of reading and writing to the magnetic stripe, the setting rank of the erase/ print heads, the status of the EEPROM setting, the type of interface being used and the ROM version are printed in order for the test results. Use a PET type card with the predetermined magnetic stripe on both sides to run a test print. When performing a test print, magnetic data for the test is written to the card. Use a card whose magnetic stripe can be overwritten without causing a problem. (Use a card that is right for the print settings on the card reader/writer.) Note: A USB cable is not an accessory part. Purchase one that meets specifications. 33
Appendix C: Optional Ethernet Interface IFBD-HE05/07 LED Push switch IFBD-HE05 Ferrite core IFBD-HE07 <Initializing Settings> To initialize the setting information, set the push switch as described below. Push the switch for 1 to 5 seconds while the unit is operating in the normal mode. The green and red LEDs will flash with a regular pattern. In this state, momentarily push the switch once again to turn OFF both the green and red LEDs. This will revert the interface board to its factory settings. After the interface board has been initialized, the unit will automatically reboot itself. <LED Display> Green (100M): Lights when the port is operating at 100 Mbps. Red (Link/Activity): Lights when the link is made between the port and the connected device, and mutual communication is enabled. <Connecting the Ethernet Cable> 1. An Ethernet cable is not included with the unit. Please provide a cable that is appropriate for the specs. 2. If a ferrite core is included, install the ferrite core onto the ethernet to prevent electrical noise. If a ferrite core is not included, perform step 3.) only. For details on how to attach the ferrite core, see the installation sheet that is supplied with the Ethernet board. 3. Insert the Ethernet cable into the interface board connector. 34
Appendix D: General Specifications Card Specification Item Card Transport Unit Transport Method Rollers Card Insertion Direction Card Travel Speed Specifications Plastic card (JIS X6301 / ISO 7810:type ID-1) One Direction 300 mm/s (at high speed: When reading) 30 mm/s (at slow speed: when erasing/printing) Magnetic Stripe Functions JISII type (1 track) read/write (TCP400) ISO type (3 tracks) read/write (TCP410) Print Unit Environment Conditions Recommended cards Power Source Interface Mass External Dimensions *1 Number of Print Characters Printing Character Types Max. 21 characters x 13 lines (504 x 320 dots) ANK Code Page 437, Code Page 858, GB, BIG 5 (Varies according to model and font settings.) External characters, graphics Dot Configuration 24 x 12, 24 x 24, 48 x 24, 24 x 48, 48 x 48 Dot Pitch Location of Use Ambient Temperature and Humidity Storage Temperature and Humidity Shock Durability Vertical Direction: 0.125 mm Horizontal Direction: 0.121 mm Indoors *1: Not including the protruding portion of the interface. 5 to 35 C, 20 to 80% RH (There must be no condensation.) -30 to 65 C, 20 to 90% RH (There must be no condensation.) 1.5 G 7 to 100 Hz XYZ Directions for one hour (When packaged) STAR Recommended Thermal Re-writing Cards AC 90 to 132 V 50/60Hz AC 198 to 264 V 50Hz USB, RS-232C D-sub 9 Pin Ethernet (option) Approximately 2.5 kg 119 (W) x 132.5 (H) x 270.5 (D) mm 35
SPECIAL PRODUCTS DIVISION STAR MICRONICS CO., LTD. 536 Nanatsushinya, Shimizu-ku, Shizuoka, 424-0066 Japan Tel: (int+81)-54-347-0112 Fax: (int+81)-54-347-0409 Please access the following URL http://www.star-m.jp/eng/dl/dl03.htm for the latest revision of the manual. OVERSEAS SUBSIDIARY COMPANIES STAR MICRONICS AMERICA, INC. 1150 King Georges Post Road, Edison, NJ 08837-3729 U.S.A. Tel: (int+1)-732-623-5555, Fax: (int+1)-732-623-5590 STAR MICRONICS EUROPE LTD. Star House, Peregrine Business Park, Gomm Road, High Wycombe, Bucks, HP13 7DL, U.K. Tel: (int+44)-1494-471111, Fax: (int+44)-1494-473333 TCP400 EN/HK/KR 2014. 10. 24 59082440